Numaligarh Refinery Limited Tender

BALL VALVE CS INT. COATED, 150,0, API 608, FLGD,B16.5,FF, LO, FULL BORE, BB, LONG PATTERN, WITH LOCKING ARRANGEMENT, A105N/A216 Gr.WCB, A182 F304 /A351 CF8, STEM SS 304, RTFE, SEAL FLEXIBLE GRAPHITE, A193 Gr.B7/A194Gr.2H, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, INTERNALLY LIQUID EPOXY COATED ACC. TO, DOC. NR-0ZZZZ-CV-SPE-0019, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 15 KG/CM2(G), DESIGN TEMPERATURE 65 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED.

BALL VALVE CS INT. COATED, 150,0, API 608, FLGD,B16.5,FF, LO, FULL BORE, BB, LONG PATTERN, WITH LOCKING ARRANGEMENT, A105N/A216 Gr.WCB, A182 F304 /A351 CF8, STEM SS 304, RTFE, SEAL FLEXIBLE GRAPHITE, A193 Gr.B7/A194Gr.2H, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, INTERNALLY LIQUID EPOXY COATED ACC. TO, DOC. NR-0ZZZZ-CV-SPE-0019, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 15 KG/CM2(G), DESIGN TEMPERATURE 65 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED.

BALL VALVE CS INT. COATED, 150,0, API 608, FLGD,B16.5,FF, LO, FULL BORE, BB, LONG PATTERN, WITH LOCKING ARRANGEMENT, A105N/A216 Gr.WCB, A182 F304 /A351 CF8, STEM SS 304, RTFE, SEAL FLEXIBLE GRAPHITE, A193 Gr.B7/A194Gr.2H, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, INTERNALLY LIQUID EPOXY COATED ACC. TO, DOC. NR-0ZZZZ-CV-SPE-0019, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 15 KG/CM2(G), DESIGN TEMPERATURE 65 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED.

BALL VALVE CS, 150,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, LONG PATTERN, WITH LOCKING ARRANGEMENT, A105N/A216 Gr.WCB, A182 F304 /A351 CF8, STEM SS 304, RTFE, SEAL FLEXIBLE GRAPHITE, A193 Gr.B7/A194Gr.2H, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 12 KG/CM2(G), DESIGN TEMPERATURE 65 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED.

GROUP-2 (GROUP WISE EVALUATION) SUPPLY OF BALL VALVE- FIRE SAFE_CS FOR AG+UG PIPPING FOR NERP PROJECT Including TPI Charges as specified in Material Requisition.

BALL VALVE CS (NACE), 150,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, FIRE SAFE, LONG PATTERN, WITH LOCKING ARRANGEMENT, ALL WELDS SHALL BE SUBJECTED, TO PWHT., SERVICE NACE, CATEGORY 1, A105N/A216 Gr.WCB, A182 F316 /A351 CF8M, STEM SS 316, SS 316, SEAL FLEXIBLE GRAPHITE, A193GrB7M/A194 Gr2HM, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, FOR SOUR(NACE) SERVICE REQ. ACC. TO, NACE MR0103,NR-0ZZZZ-PI-SPE-0025 AND IN-043, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 3.5 KG/CM2(G), DESIGN TEMPERATURE 300 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED.

BALL VALVE CS (NACE+CAUSTIC), 150,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, FIRE SAFE, LONG PATTERN, WITH LOCKING ARRANGEMENT, ALL WELDS SHALL BE SUBJECTED, TO PWHT., SERVICE NACE, CATEGORY 1, A105N/A216 Gr.WCB, A182 F316 /A351 CF8M, STEM SS 316, RTFE, SEAL FLEXIBLE GRAPHITE, A193GrB7M/A194 Gr2HM, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, FOR SOUR(NACE) SERVICE REQ. ACC. TO, NACE MR0103,NR-0ZZZZ-PI-SPE-0025 AND IN-043, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 16.5 KG/CM2(G), DESIGN TEMPERATURE 120 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED.

BALL VALVE CS (H2 SER.), 300,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, FIRE SAFE, LONG PATTERN, WITH LOCKING ARRANGEMENT, ALL WELDS SHALL BE SUBJECTED, TO PWHT., A105N/A216 Gr.WCB, A182 F304 /A351 CF8, STEM SS 304, RTFE, SEAL FLEXIBLE GRAPHITE, A193 Gr.B7/A194Gr.2H, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE1 44.6 KG/CM2(G), DESIGN TEMPERATURE1 190 DEG.C, DESIGN PRESSURE2 13.2 KG/CM2(G), DESIGN TEMPERATURE2 80 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED.

BALL VALVE CS (H2 SER.), 300,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, FIRE SAFE, LONG PATTERN, WITH LOCKING ARRANGEMENT, ALL WELDS SHALL BE SUBJECTED, TO PWHT., A105N/A216 Gr.WCB, A182 F304 /A351 CF8, STEM SS 304, SS 304, SEAL FLEXIBLE GRAPHITE, A193 Gr.B7/A194Gr.2H, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 12.2 KG/CM2(G), DESIGN TEMPERATURE 340 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED.

BALL VALVE CS (NACE+CAUSTIC), 300,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, FIRE SAFE, LONG PATTERN, WITH LOCKING ARRANGEMENT, ALL WELDS SHALL BE SUBJECTED, TO PWHT., SERVICE NACE, CATEGORY 1, A105N/A216 Gr.WCB, A182 F316 /A351 CF8M, STEM SS 316, RTFE, SEAL FLEXIBLE GRAPHITE, A193GrB7M/A194 Gr2HM, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, FOR SOUR(NACE) SERVICE REQ. ACC. TO, NACE MR0103,NR-0ZZZZ-PI-SPE-0025 AND IN-043, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 35 KG/CM2(G), DESIGN TEMPERATURE 120 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED.

BALL VALVE CS (NACE+CAUSTIC), 300,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, FIRE SAFE, LONG PATTERN, WITH LOCKING ARRANGEMENT, ALL WELDS SHALL BE SUBJECTED, TO PWHT., SERVICE NACE, CATEGORY 1, A105N/A216 Gr.WCB, A182 F316 /A351 CF8M, STEM SS 316, RTFE, SEAL FLEXIBLE GRAPHITE, A193GrB7M/A194 Gr2HM, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, FOR SOUR(NACE) SERVICE REQ. ACC. TO, NACE MR0103,NR-0ZZZZ-PI-SPE-0025 AND IN-043, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 35 KG/CM2(G), DESIGN TEMPERATURE 120 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED.

BALL VALVE CS (NACE+CAUSTIC), 300,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, FIRE SAFE, LONG PATTERN, WITH LOCKING ARRANGEMENT, ALL WELDS SHALL BE SUBJECTED, TO PWHT., SERVICE NACE, CATEGORY 1, A105N/A216 Gr.WCB, A182 F316 /A351 CF8M, STEM SS 316, RTFE, SEAL FLEXIBLE GRAPHITE, A193GrB7M/A194 Gr2HM, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, FOR SOUR(NACE) SERVICE REQ. ACC. TO, NACE MR0103,NR-0ZZZZ-PI-SPE-0025 AND IN-043, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 35 KG/CM2(G), DESIGN TEMPERATURE 120 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED.

BALL VALVE EXT. BONNET LTCS, 600,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, FIRE SAFE, LONG PATTERN, WITH LOCKING ARRANGEMENT, EXT. BONNET ACC. TO BS 6364, (NON-COLD BOX APPLICATION), A350LF2CL1/A352GrLCB, A182 F316 /A351 CF8M, STEM SS 316, SS 316, SEAL FLEXIBLE GRAPHITE, A193 Gr.B7/A194Gr.2H, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 66.5 KG/CM2(G), DESIGN TEMPERATURE 70 DEG.C, DESIGN PRESSURE -1.01 KG/CM2(G), DESIGN TEMPERATURE -45 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED.

GROUP-3 (GROUP WISE EVALUATION) SUPPLY OF BALL VALVE- FIRE SAFE_SS FOR AG+UG PIPPING FOR NERP PROJECT Including TPI Charges as specified in Material Requisition.

BALL VALVE SS DUAL, 150,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, FIRE SAFE, LONG PATTERN, WITH LOCKING ARRANGEMENT, A182F304/L A351CF3/M, A182 F316 /A351 CF8M, STEM SS 316, RTFE, SEAL FLEXIBLE GRAPHITE, A193 Gr.B7/A194Gr.2H, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, SHALL BE A182 Gr.F304/304L OR, A351 Gr.CF3/CF8, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE1 10.5 KG/CM2(G), DESIGN TEMPERATURE1 65 DEG.C, DESIGN PRESSURE2 18 KG/CM2(G), DESIGN TEMPERATURE2 65 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED., SHALL BE DUAL CERTIFIED AND THE, MAXIMUM CARBON CONTENT SHALL BE 0.03%

BALL VALVE SS DUAL, 150,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, FIRE SAFE, LONG PATTERN, WITH LOCKING ARRANGEMENT, A182F304/L A351CF3/M, A182 F316 /A351 CF8M, STEM SS 316, RTFE, SEAL FLEXIBLE GRAPHITE, A193 Gr.B7/A194Gr.2H, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, SHALL BE A182 Gr.F304/304L OR, A351 Gr.CF3/CF8, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE1 10.5 KG/CM2(G), DESIGN TEMPERATURE1 65 DEG.C, DESIGN PRESSURE2 18 KG/CM2(G), DESIGN TEMPERATURE2 65 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED., SHALL BE DUAL CERTIFIED AND THE, MAXIMUM CARBON CONTENT SHALL BE 0.03%

BALL VALVE SS DUAL, 300,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, FIRE SAFE, LONG PATTERN, WITH LOCKING ARRANGEMENT, A182F304/L A351CF3/M, A182 F316 /A351 CF8M, STEM SS 316, RTFE, SEAL FLEXIBLE GRAPHITE, A193 Gr.B7/A194Gr.2H, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, SHALL BE A182 Gr.F304/304L OR, A351 Gr.CF3/CF8, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 12 KG/CM2(G), DESIGN TEMPERATURE 65 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED., SHALL BE DUAL CERTIFIED AND THE, MAXIMUM CARBON CONTENT SHALL BE 0.03%

BALL VALVE SS DUAL (H2 SER., 600,0, API 608, FLGD,B16.5,RF, LO, FULL BORE, BB, FIRE SAFE, LONG PATTERN, WITH LOCKING ARRANGEMENT, A182F304/L A351CF3/M, A182 F316 /A351 CF8M, STEM SS 316, SS 316, SEAL FLEXIBLE GRAPHITE, A193 Gr.B7/A194Gr.2H, SPRINGS INCONEL X-750, SUPP. REQUIREMENTS, VALVE BORE SHALL BE FULL BORE FOR 1/2" TO, 11/2"AND SINGLE REDUCED BORE FOR 2" & ABOVE, SHALL BE A182 Gr.F304/304L OR, A351 Gr.CF3/CF8, ADD. INFORMATION, DOCUMENTS TO BE FOLLOWED, TK-1ZZZA-PI-SPE-0005,TK-1ZZZA-PI-SPE-0006,, TK-1ZZZA-PI-SPE-0008,TK-1ZZZA-PI-SPE-0009, AND IN-042, VENDOR TO SUBMIT PRESSURE-TEMP., RATING CHART, DESIGN PRESSURE 44.6 KG/CM2(G), DESIGN TEMPERATURE 190 DEG.C, VALVE SHALL HAVE 120MM EXTENDED SPINDLE, (MEASURED FROM THE VALVE BONNET) TO ENSURE, THAT THE LEVER CLEARS VALVE INSULATION., FOR TRUNNION MOUNTED VALVES SEALANT /, LUBRICANT / FLUSHING INJECTION S, ASSEMBLIES SHALL BE PROVIDED FOR THE, AND OR STEM SEAL. REFER CLAUSE B.5.16 OF, TK-1ZZZA-PI-SPE-0009., VALVE SHALL BE SUITABLE FOR, BI-DIRECTIONAL FLOW & PRESSURE SHUTOFF, VALVE SHALL BE TESTED IN PREFERRED AND, NON PREFERRED FLOW DIRECTION., PREFERRED FLOW DIRECTION SHALL BE MARKED., SHALL BE DUAL CERTIFIED AND THE, MAXIMUM CARBON CONTENT SHALL BE 0.03%