Northeast Frontier Railway Tender

Single Row Angular contact ball bearing SKF 7213 B, PN: WJ-18 size: 65 mm ID, 120 mm OD, 23mm thickness MAKE :MBE

Single Row Deep Groove ball Bearing SKF 6208, PN: WJ- 21 size: 40 mm ID, 80 mm OD, 18 mm Thickness MAKE :MBE 6

Standard Duplex Roller Chain Part No: Drg/JMP/WJ-33 Make:Daimond 7

Chain Cover WJ-30/M MAKE: SSA 8

Leather Bellow PART No: Drg/JMP/WJ 8/M MAKE: SSA 9

Juliee Clip Top & Bottom Drg/JMP/WJ-22/M MAKE: SSA 10

Sprocket Large PART NO- Drg/JMP/WJ 24/M with key MAKE: SSA 11

Check Nut of worm Drg/JMP/ WJ-27 MAKE: SSA

Check nut of screw spindle MAKE: SSA

KEY FOR WORM WHEEL ,SCREW SPINDLE Drg/JMP/ KY-43 , SPROCKET LARGE Drg/JMP/ KY-63 , L/H & R/H With ey & Pin WJ/97/M-WJ/98/M,KY-36 MAKE: SSA 14

WASHER SCREW SHAFT MAKE :SSA 15

Link Right Hand & Left Hand Drg/JMP/ WJ/97/M- MAKE: SSA 16

Side Wheel Drg/JMP/ WJ-84 MAKE: SSA 17

Rear Wheel Drg/JMP/ WJ-83 MAKE: SSA 18

Lever Arm (Bush) WITH KEY & PIN Drg/JMP/WJ/93/M MAKE: SSA 19

Worm Shaft Drg/JMP/WJ 25 Drg/JMP/ WJ-101 MAKE: SSA

5-Pin & 4 Pin Plug MAKE:BCH

Pendent type push button assembly with 2 nos. of normally open \inching type push button suitable for cable entry arrangement for 35 Ton Jack MAKE : SNT 3

16 Amps Contactor MAKE:BCH 4

32 Amps Contactor MAKE:BCH 5

Overload Relay with terminal MAKE:BCH 6

PUSH BUTTOM & NO+NC

Elbow-3Pcs.,Tee-3Pcs.,Pipe10ft-1Pcs.,MTA-3Pcs.,Bend-3 Pcs., Nipple 2" - 3 Pcs.Small Nipple with Check Nut or limit switch - 3 Pcs. Metallic Pipe-3Mtr.,Plastics Pipe- L type plate :3nos & U type plate :1 no. MAKE: INDIGENOUS

Heavy duty general purpose limit switch oil tight on line die cast aluminum housing suitable for 35 Ton Jack upply quick brake spring loaded lever with roller 01 no. + 01 NC with normal angular roller lever MAKE:BCH

5 HP brake Motor with fail safe disc brake assembly. as follows:- Motor 5 HP squirrel cage totally enclosed an cooled horizontal foot mounted brake (Motor Repairing Only) MAKE :DELTA

(A) Direct Online Starter wall mounting type with push button control, suitable for 3 phase 50 HZ. 415V for 30HP Motor. The contactor coil of the starter must be suitable for 415 V. 50 HZ. AC supply. The starter shall be complete with over load and NO Volt. Protection. Material Specification: IS: B544 (Part-1) IS: 13947- 4 - 1. Make: BCH /SIEMENS / Havells / Jeevan / SCHNEIDER / L&T., Qty-1 no. (B) Supply & Fitment of Material for 30 HP DOL Starters (Master) in SL. No. (A) of 25T Universal JMP Jack (i) Red phase indicating LED lamp 415V AC Qty-1 No. (ii) Yellow phase indicating 10 LED lamp 415 V AC Qty-1 No.(iii) Blue phase indicating LED lamp 415 V AC Qty-1 No. (iv) On indicating LED lamp 415V AC (Red) Qty-1 No. (v) Off indicating LED lamp 415V AC (Green) Qty-1 No. (vi) Trip indicating LED lamp 415V AC (Amber) Qty-1 No. (vii) Emergency push button Qty-1 No. (viii) 0-500V AC analog voltmeter Qty-1 No. (ix) 3 phase voltmeter selector switCh Qty-1 No. (x) Single phasing, phase reversal/phase sequence protec(ion relay Qty-1 No. (xi) Reset button to release overload relay in case of tripping Qty-1 No. (xii)TB 30A 6 way Qty-1 No. (xiii) TB 30A 4 way Qty-1 No. & (xiv) 63 Amp. MCB switch (fitted on outer panel) (1 set consisting of SI No. i to xiv) Make :BCH/ SIEMENS / Havells / Jeevan / SCHNEIDER / L&T. (1 set consisting of SI No. A & B). OFFER MAKE:BCH

(A) Direct On line Starter with Z sets of 3 pole / 4 pole contactors (2 sets AC contactor coils, 25 AMP each),each set controlled separately by 415V, SOHZ AC Contactor Coils. One set of contactor coil is to be controlled by the forward direction of rotation through an inching type push button and the other set through another inching button to control the reverse direction of 7.5 HP, 3Phase, SOHZ. 415VoIts, AC Motor. There must be electrical interlocking contact to prevent both set of contactors to close simultaneously. Each of above push buttons should have one normally closed auxiliary contact and one stop push buttons are required. The starter shalJ be complete with over load, shall be wired and shall be provided with power plug and socket with locking arrangement as 11 shown in schematic Drawing No. 1736/23 and 1737/23 Alt.-1. Each starter is to be provided with 2 Nos. power plug and sockets and 2 Nos. of control plug and sockets. Maximum Dimension of the starter should not excessed 280mm (B) X 430mm (L) X 175mm (T) irrespective of Dimension. Material Spec.: IS: 13947 Pt.-4 Sec.-1, 1993, Make: BCH or SIEMENS or Havells or Jeevan / SCHNEIDER or L&T. Qty. 1 no. (B)Supply & Fitment of Material for 7.5 HP DOL Starters (Individual) in SL No. (A)of 25T Universal JMP Jack SI No. (i) Up indicating LED lamp 415V AC (Red) Qty-1 No. (ii) Down indicating LED lamp 415V AC (Red) Qty-1 No. (iii) Trip indicating lamp 415V AC (Amber) Qty-1 No. (iv) ) 415V AC 2NO+2NC FS-C 45MM Control Relay Qty-1 No. (v) 3 Phase (RYB) indicating LED lamp, (vi) Reset Button to release overload relay in case of tripping Qty-1 No. & (vii) 30A 3 way terminal block Qty-2 Nos. (1 set consisting of SI No. i to vii) Make:BCH/Siemens/L&T/C&S/ Jeevan. (1 set consisting of SI No. A & B). OFFER MAKE:BCH 12

Coil for brake motor MAKE:DELTA

Air break direct on line starter with 2 sets of 3 pole contactor each set controlled separately by 415 V, 50 Hz, AC cotactor coil. One set of contactor coil is to controlled by the forward direction of rotation through an inching type push button and the other set through another inching button to control the reverse direction of 5 HP, 3 phase, 50 Hz, 415 V, AC motor. There must be 13 electrical interlocking contact to prevent both set of contactors to close simultaneously. Each of above push buttons are required. The starter shall be complete with overload, shall be wired and shall be provided with power plug and socket with locking arrangement as shown in schematic diagram Drg. 1736/23 and 1737/23. Each starter is to be provided with 2 Nos. power plug and sockets and 2 nos. control plugs and sockets. Maximum dimension 280 mm (B) x 360 mm (L) x 162 mm (T). Acceptable brand - BCH, HAVELLS and JEEVAN

Single core 2.5 sq.mm (80/0.2 mm) copper conductor insulated and sheathed cable 1100V Grade, 1 Roll of 90 MTR MAKE: EVERSHINE KDK

4 core cable 2.5 sq. mm (48/0.2mm) copper conductor insulated and heavy duty sheathed flexible core 1100 volt grade conforming to IS-694 (PL-1) 1981, 1 Roll of 100 MTR. MAKE: EVERSHINE KDK