NHPC Limited Tender

Providing soling in foundation and under floor with stone/best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering complete. Stone soling of thickness 150mm.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).(a) In prop 1cement: 3 sand :6 coarse aggregate by volume

Providing Ceramic Tiles of approved quality, size, shape and thickness not less than 8 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with fix-A Tile Choksey/ Sika/ Pedelite/ Rouf/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department).a)Normal range Somany/ Orient/Nitco /Asian Make(II)Of size 400mmx400mm and above

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side d) In cement mortar 1:6

Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)(i) Thickness = 1.5 mm thick

Wall painting (two coats) with acrylic emulsion paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth.(a).Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

(a) Removing white or colour wash by steel wire brushing and/ or scraping, sand papering and preparing the wall surface smooth including necessary repairs to scratches complete.

CEMENT PAINT & PRIMER b) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new wall surface (two coats) to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials.

Removing old paint or polish from wood and wood base surfaces with casti soda solution and making the surface even.

Painting one coat (excluding priming coat) on old wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of all dirt, dust and other foreign matter sand papering and stopping.

Extra over item no 13.6.5 & 13.6.6 for every subsequent coat of paint. (i) Surfaces over 100mm in width or girth. a) General purpose (Asian paint/Berger paint/ICI paint/J&N paint/Nerolac).

Painting one coats on old G.C.I sheets with ready mixed anticorrosive paint of approved brand and shade suitable for painting over C.I sheets to give an even shade including the cleaning the rust patches with emery paper, dust ,dirt, grease and other foreign matter with water complete.

Extra over item no.13.8.3 for every subsequent coat of paint.

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately)(A) 112mm thick brick wall (a) In cement mortar in proportion 1:4. (1 cement:4 sand)

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) b) M20 grade concrete or Prop. 1:1.5:3

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar

Providing polished granite tiles of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department)(i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) M/F Suspended Ceiling which includes G.I. perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I. intermediate Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two equal flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm c/c, 9.5mm/ 12.5mm tapered edge Gypboard (conforming to IS:2095-1982) is then screw fixed to ceiling section with 25mm long drywall screws at 230mm c/c. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally, the boards are to be jointed and finished so as to have a flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, joint paper tape and two coats of drywall topcoat suitable for Gypboard complete at all levels as specified and directed. (For light fittings, providing opening for doors, window, ventilators etc, cut out made with frame of perimeter channel supported suitably to be measured and paid separately where necessary). channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25mmx10mmx0.55mm thick fixed to soffit with G.I.cleat and steel expansion fasteners. (I) 9.5mm thick

Providing corrugated galvenised Iron sheet roofing of TATA SHAKTEE / SAIL including fitting and fixing necessary galvenised J or L hooks, bolts and nuts 8 mm dia with bitumen washer 25 mm dia x 3 mm thick and 1.6 mm thick limpet washer complete excluding cost of roof truss, purlin etc. (Roof trusses and purlin etc.to be measured and paid separately). (b) 0.50 mm thick

Providing and fixing clear sheet glass beded in putty and fixed with/without wooden bidding including necessary cutting and glass to be required sized(payment for wooden bead shall be made separately)(b). 4.00mm thick.

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws.b) Non decorative type and block board core. (i) 40 mm thick .

Applying priming coat over new wood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. (b)With ready mixed paint , wood primer (white).

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping.(i).Surfaces over 100mm in width or girth.a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Supplying, fitting and fixing PVC pipes 6kg/sqcm(supreme/prince)or otherISI approved including joining .fitting and fixing wiyh clamp etc.as necessary complete at all level including below G,L as directed and specified. b) Concealed bu chiselling or breaking brick wall/C.C./RCC and making good to the damages. III) 90mm dia

Supplying fitting and fixing GI pipes of following sizes with all necessary 'R' brand or similar approved GI fittings such as bend, Tee, elbow, reducer, nipple, plug, long screw fitting, HW clamps etc complete at all levels including below GL as directed and specified.Concealed bu chiselling or breaking brick wall/C.C./RCC and making good to the damages Structure. f)15mm Dia (Medium) Use Tata Make

Providing vitreous china wash basin with CI/MS brackets,C.p Brass chain with plug,PVC waste pipe including painting of fitting and brackets, cutting and making good the wall wherever required, (Pillar Cock,Stop cocks waste coupling are to be paid separately) Basin (without pedestal)(B) Hindware make (a) White(II)Standard 630x450(cat.No.10001)

Providing and fixing white vitreous china pedestal type water closet (European type WC pan 400mm high) with seat and lid, CP brass hinges and rubber buffers, C.I / MS brackets, 40mm dia flush bend, with fittings including painting of fittings and brackets required :(Flushing cisturn to be paid separately)(C ) Jaquar Make (B ) Hindware make (a)White (III)Water closet POPULAR P (Cat.No. 20044)(including of seat cover)

Supplying, fitting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. complete as directed and specified (pipes will be measured separately)Hindware make White (i) Sleek+ PVC cistern

Supplying and fitting gun metal country pit valve (full way valve) ISI, make as specified and directed .(e) 15mm dia

Renewing GI union joint (heavy quality) as specified and directed.a) 15mm dia

Supplying fitting and fixing CP bib cock 15mm dia of approved brand as directed and specified. (GI & CP pipes will be measured seperately) Essco make (Delux / Sumthing spl. / Tropical) I c) Two way long body bib cock with wall flange

Supplying fitting and fixing CP pillar cock of 15mm dia of approved brand as directed and specified. (ii) Jaquar make (a ) Continental

Supplying fitting and fixing CP stop cock of approved brand and size as mentioned below as directed and specified. (GI & CP pipes will be measured seperately)(I )brass stop cock (Haevy) of sant make (i)15mm Dia

Providing , Fitting and fixing chrome plated soap dish complete as specified and directed. Jaquar Make ( I ) Jaquar Make (a ) Continental ( Cat .No-CAN -1331 N )

Providing , Fitting and fixing chrome plated towel rail complete as directed and specified . ( B )Sona make ( I ) Towel rail Diplomate long ( Cat No- TR-0605)

Providing, fitting and fixing chrome plated towel ring complete as directed and specijfied ( b ) Sona make (I )Towel ring round ( Cat no-TR-06051 )

Providing , Fitting and fixing chrome plated toilet paper holder complete as specified and directed.( B ) Agmeco make (iii )Econ ( CatNO- EN-00001 )

Providing fitting and fixing Mirror with plastic frame of size 500x400mm complete as directed and specified.

Providing , Fitting and fixing Glass shelf with C.P guard rail (i) Sona make (Cat.no.TR-0701) (a ) 450 mm long.

Providing fitting and fixing stainless steel kitchen sink of parryware make with CI/MS brackets,C.P. Brass chain with rubber plug,PVC waste pipe etc. & making good the wall wherever required.(Sink cock,stop cocks,waste coupling are to be paid separately.(A) Parryware make (VI) Single Bowl(160x180)Flat Edge Glossy(Cat.No.C8538)