Industries And Commerce Department Tender

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size necessary screws. Kiln seasoned and chemically treated hollock wood 30 mm thick

Providing and fixing PVC Door frame of size 50x47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screw, the vertical door profile to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm, including providing EPDM rubber gasket weather seal trhoughout the frame, including jointing 5 mm PVC frame to be fixed to the wall using 8 x 100 mm long anchor fasteners complete, all as per manufacturer's specification and direction of Engineer -In-Charge.

35 mm thick factory made solid panel PVC Door Shutter, made out of single piece extruded soild PVC profile, 5 mm (±0.2 mm) thick, having style & rails (except lock rail) of size 95 mm x 95 mm x 5 mm, out of wich 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm x 20 mm x 1mm, joints of style & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm x 100 mm of cross section size 35 mm x 17 mm 1 mm at each corner. Single piece extruded 5 mm thick soild PVC lock rail of size 115 mm 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends,having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screw of 125 mm 11 mm, including providing 5 mm single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineer-In-Charge. Non decorative finish (matt finish)

Cement concrete flooring 1:2:4(1 cement :2coarse sand: 4graded stone aggregate) finished with a floating coat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I limpet washers or which G.I limpet washer filled with white lead, including a coat of approved steel primer and two of approved paint on overlapping of sheets complete(up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately): Natural colour insulating board 12 mm thick

15 mm cement plaster on the rough side of single or half brick wall of mix: 1:4 (1 cement : 4 fine sand)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction od Engineer-in-Charge. External work

15 mm nominal dia pipes

65 mm nominal pipes

ELECTRICAL WORKS

TUBE LIGHT

CEILING FAN

FLOOD LIGHT 23 WATTS

LED BULB 9 WATTS

LABOUR CHARGES