Indian Institute Of Entrepreneurship Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 5,47,909Document Cost
₹ 10,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2021_IIE_615546_1Bid Award Id
ViewTender No
F(244)/19-20/222(A)Tender Authority
Indian Institute Of Entrepreneurship ViewPurchaser Address
-Website
http://eprocure.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc height of propping and centering below supporting flor to ceiling not exceeding 4m and removal of the same for in-situ reinforced concrete and plain concrete work in:
Foundation , footings, bases of columns, pile cap, raft and mass concrete works etc
(i) Using 25mm thick plank.
57.84
-
-
... More
Providing and laying plain/ reinforcement cement concrete works in prop 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone chips,20mm down) including dewatering if necessary and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately).
Foundation, footing, columns with base ,tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank inspection pit and the like and other works not less than 100mm thick.(M 20)
35.05
-
-
... More
Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. Work/ R.B. wailing including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports , chairs, spacers etc.
complete (up to 1st floor level).
(a) TMT Bar
i) TATA/SAIL
68.15
-
-
... More
Brick work in cement mortar with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed in sub-structure up to plinth level.
(a) In proportion 1:4
5.33
-
-
... More
12mm thick cement plaster in single coat on fair side of brick/
concrete walls for plastering up to 1st floor level including arises, internal rounded angles, chambers and /or roounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. (b) In cement mortar 1:4.
1949.03
-
-
... More
m) Distempering two coats with oil bound distemper of approved brand and manufacture and of required shade on new wall surface to give an even shade, over and including a priming coat with distemper primer of approved brand and manufacture after throughly brooming the surface free from mortar dropings and other foreign matter and including preparing surface even and sand papered smooth.
(i).Priming coat with distemper primer
21479.98
-
-
... More
(ii). Top coat
21479.98
-
-
... More
Finishing wall with two coats of acrylic emulsion exterior coatings of approved brand of required shade, thinning by assing water as per the specification of manufacture after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials as specified and directed by the department.
c) Asian paint/Berger paint/ICI paint/J & N paint/Nerolac
5826.69
-
-
... More
15mm thick cement plaster in single coat on fair side of brick/concrete walls for exterior plastering up to 1st floor level including arises, internal rounded angles, chambers and /or roounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. With cement mortar 1:4 (1 cement : 4 fine sand)
1609.52
-
-
... More
DEMOLISHING / DISMANTLING WORKS:
Demolishing the plastering from walls/ R.C.C and P.C.C members without causing any damage to the wall/member upto any height including disposal of debris as directed for all levels
226.56
-
-
... More
Demolishing R.C.C. Work including stacking of steel bars and disposal of unserviceable material as directed for all levels
10.13
-
-
... More
Demolishing C.C. floors of various thickness including top layer and base course and disposal of debris as directed for all levels
109.81
-
-
... More
Dismantling and removing the existing door and window frame(chowkath) both wooden and steel of different sizes without damaging the walls and removing the frame and necessary repairs to the edges of the walls as directed by for all levels
110
-
-
... More
Demolishing brick work including stacking of serviceable materials and disposal of unserviceable materials as directed for all levels.
1.36
-
-
... More
Dismantling all types of ceiling, partition and wall lining and stacking the materials as directed by the department for all levels
295
-
-
... More
Demolishing skirting/ dado in walls/ RCC and PCC members without causing damage to walls/ member upto any height including disposal of debris as directed for all levels
157.32
-
-
... More
Dismantling of existing steel windows/ steel ventilators/ steel windows and steel ventilators without damaging the walls, removing to a safe place and necessary repairs to the edges of the walls.
248.55
-
-
... More
NEW CIVIL WORKS:
Supplying and filling sand in foundation trenches of column footings over slushy soil including including local carriage of materials within 8 km pumping out of water, ramming etc. complete for strengthing the bearing capacity of the soil as directed and specified including payment of forest royalty and sales tax and other duties and taxes as may be necessary
112.84
-
-
... More
112 MM Thick 1st class brick nogged wall in cement mortar including rackling out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S. Rod/ Tor steel of column to be embeded in cement mortar and will be measured and paid separetely).
Cement mortar 1:4 (1 cement :4 coarse sand)
29
-
-
... More
Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc height of propping and centering below supporting flor to ceiling not exceeding 4m and removal of the same for in-situ reinforced concrete and plain concrete work in:
Lintels, beams, plinth beams, girders, bressumers and cantilevers.
12
-
-
... More
Providing and fixing hand rail by welding etc to steel ladder railing bolcony railing & staircase railing including applying a priming coat of approved steel primer MS tube (Medium) 40mm nominal boar
1230
-
-
... More
Providing and laying plain/ reinforcement cement concrete works in prop 1:1:2 (1 cement :1 coarse sand :2 graded stone chips,20mm down) including dewatering if necessary and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately)
Foundation, footing, columns with base ,tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank inspection pit and the like and other works not less than 100mm thick.
Using admixture,plasticiser etc for air entraining, water reducing
purposes including addition of agent for changing normal setting
time of concrete as required(M 25)
4.23
-
-
... More
Providing two coats of Birla White Wall Care Putty(Water resistant white cement based putty for concrete/mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of energy stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department.( Total thickness of two coats is maximum 1.5mm) (INTERIOR ALL FLOORS)
8321
-
-
... More
Applying one coat of cement primer of approved brand and manufacture on new wall surface after thoroughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.
8321
-
-
... More
Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth.
(a) Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)
8321
-
-
... More
Providing two coats of Birla White Wall Care Putty(Water resistant white cement based putty for concrete/mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of energy stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department.( Total thickness of two coats is maximum 1.5mm) (EXTERIOR ALL FLOORS)
3866
-
-
... More
Applying one coat of cement primer of approved brand and manufacture on new wall surface after thoroughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.
3866
-
-
... More
Applying one self-priming coat of acrylic emulsion exterior paint of approved brand, thinning by adding water as per the specification of manufacturer over freshly plastered wall surface after throughly brooming the surfaces free mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth as specified and directed by the department
c) Asian paint/Berger paint/ICI paint/J & N paint/Nerolac
3866
-
-
... More
Finishing old/ new wall with water proofing weather coat smooth anti-fungal exterior painting of Apex brand of Asian paints and of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats)
2773
-
-
... More
Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter.
(i) Surface over 100mm in width or girt
b) High gloss( asian paint/ berger paint/ ici paint/ j & n paint/ nerolac)
5097.42
-
-
... More
Applying priming coat over new wood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting.
(a) with ready mixed paint, wood primer (pink)
2014.23
-
-
... More
Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (asian paint/ berger paint/ ici paint/ j & n paint/ nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping.
(i) Surface over 100mm in width or girth
b) High gloss( asian paint/ berger paint/ ici paint/ j & n paint/ nerolac)
2014.22
-
-
... More
Applying mordent solution of approved brand and manufacture on new C.I sheet for preparation of surfaces for painting @5.00 litre/100 sq. metre of surface and rubbing the solution with brush including thoroughly cleaning the surface of oil, grease, dirt and other foreign matter.
433.51
-
-
... More
Providing polished granite slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-
Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department).
(i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)
57.92
-
-
... More
Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed.
(A) CERAMIC Somany made- VC Shield (Group- 25) (605x605) mm
195
-
-
... More
Kota-stone slab flooring of 18 mm thick over 20mm thick base of cement plaster 1:6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.
(1) 550mm x 550mm
41.22
-
-
... More
Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls).
c) Deluxe range
i) Of size 300mmx600mm and above
211.36
-
-
... More
Supplying and installing uPVC- Fixed Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC multichambered sections of wall thickness 2.4mm with corners fusion welded, fully reinforced with galvanized steel 1.5/2mm including glazing bead , grooving bead, drain cap, fisher screws, packing pieces, necessary stainless steel screws etc. complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers and with suitable water draining system. Application of Silicon sealant from inside / outside of dowcorning / GE or equivalent.
With 5mm clear glass
(a) Fixed window using uPVC sections of size 58mm x 52mm x 2.4mm thick wall for frame and 58mm x 68mm having 2.4mm thick wall for glass sash having reinforcement of 1.5mm thick in both frame & sash.
(WINSTA KOMMERLING/ FINESTA/ ENCRAFT)
24.36
-
-
... More
Supplying and installing uPVC- Sliding Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC multichambered sections of wall thickness 2.4mm with corners fusion welded, fully reinforced with Galvanized steel 1.5/2mm including interlock profile, glazing bead, grooving bead, brush seal, aluminum sliding track, stainless steel rollers, sealing wedge block, Espag, int handle, pop up handle, keeper, drain cap, fisher screws, packing pieces with all necessary stainlessness screws etc. complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers and with suitable water draining system. Application of silicon sealant from inside / outside of Dowcorning / GE or equivalent.
With 5mm clear glass
(b) 2 Track Sliding Window without Flyscreen using uPVC section of size 58mm x 53mm x 2.4mm thick wall for frame, 37mm x 61mm x 2.4mm thick wall for glass sash having 1.5mm thick reinforecement for both frame & sash, Interlock: 43mm x 23mm (Glass Panel)
(WINSTA KOMMERLING/ FINESTA/ ENCRAFT)
(ii) 4-Panel with 5mm clear float glass
61.21
-
-
... More
Supplying and installing uPVC- Casement Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC sections of wall thickness 2.4mm, multichambered with corners fusion welded, fully reinforced with Galvanized steel 1.5/2mm including glazing bead, folding gasket, glazing gasket, friction stay, Espag handle, Espag, keeper, drain cap, run up block, fisher screws, packing pieces with all stainless steel screws complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets,bridging wedges and glass packers and with suitable water draining system. Fittings ROTO / GQ or Equivalent. Application of Silicon sealant from Inside / Outside of Dowcorning / GE or equivalent.
a) Single leaf Side hung Window using uPVC section of size 58mm x 57mm x 2.4mm thick wall for frame, 58mm x 68mm x 2.4mm thick wall for glass sash.
With 5mm clear float glass
(WINSTA KOMMERLING/ FINESTA/ ENCRAFT)
47.11
-
-
... More
Providing wood work in frame (chowkaths) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mmx3mmx250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C and masonry as directed and specified. (a) With sal wood
2.8
-
-
... More
Exterior cladding
1038.26
-
-
... More
Re-barring for slab, beam at appropriate position strictly as per manufacture specification complete 8 MM
120
-
-
... More
10 MM
85
-
-
... More
12 MM
73
-
-
... More
Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department)
18.23
-
-
... More
REPAIRING WORKS:
Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40mm dia. M.S. tube 1.5 m centre to centre horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge .The lavational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding.
3598
-
-
... More
WATER PROOFING WORKS:
Repairing of exterior plaster:
Extra for providing and mixing Integral waterproofing liquid admixture & plasticiser Conplast X421 IC of Fosroc Chemicals /Rheomac 707 of BASF/Dr.Sealkit Normal Plast (Asian Chemicals) @ 100ml per bag of cement in concrete for waterproofing structures like roof slabs, basement, sunken slabs, chajjas, tunnels water tank etc. as specified and directed by the Department complete at all levels. In Plasters/ mortars of proportion:
1 : 4 (1cement : 4coarse sand)
27
-
-
... More
Roof water proofing treatment: WATER PROOFING OF CHAJJAS, ROOF SLABS, TERRACES, SUNKEN SLABS, SEPTIC TANK,OH TANK, RAFT SLAB IN BASEMENT, WALLS ETC: Surface preparation should be done by making surface free from oil, grease, wax, dirt or any other form of foreign matter which might affect adhesion. Spalled and deeply disintegrated concrete should be removed to sound concrete and repaired. Application of waterproofing coating BRUSHBOND ROOF GUARD is high build fibre reinforced seamless waterproofing render suitable for waterproofing of old & new roofs, it is a polymer base product applied in three.
810
-
-
... More
Waterproofing treatment of sunken slab:
Applying 2 coats of 1mm thick elastomeric cementitious waterproofing coating Brushbond RFX of Fosroc Chemicals /Dr.Sealkit Flexbond AP 122 C (Asian Chemicals) / MASTERSEAL 550EL of BASF for waterproofing structures like roof slabs, basement, sunken slabs, chajjas, tunnels, water tank etc. after proper surface preparation and soaking the surface with water prior to application complete as specified and directed by the Department at all levels
195
-
-
... More
Expansion joint treatment.:
Providing treatment of expansion joints by the following process as specified and directed by the department. (a) Preparation of groove by nosing the groove in required sizes with Cement sand mortar (in prop 1:4)
mixed with Sika Latex of Sika India Ltd. /Dr. Sealkit Master Bond Latex(Asian Chemicals)@ 4% by weight of cement as specified & directed by theDepartment complete after proper surface preparation including cleaning/ chipping removing all sorts of loose particles and foreign materials and cleaning surface thoroughly (surface preparation including thorough cleaning of surface to bemeasured and paid separately).
52
-
-
... More
Spalled concrete treatment: Dismantling of the spalled concrete by hacking the loose concrete till sound concrete is found. All surfaces should be free from debris or loose material and properly cleaned with REEBAKLENS the concrete remover cleaning and etching agent.
805
-
-
... More
Internal wall treatment :
Extra for providing and mixing Integral waterproofing liquid admixture & plasticiser Conplast X421 IC of Fosroc Chemicals /Rheomac 707 of BASF/Dr.Sealkit Normal Plast (Asian Chemicals) @ 100ml per bag of cement in concrete for waterproofing structures like roof slabs, basement, sunken slabs, chajjas, tunnels, water tank etc. as specified and directed by the Department complete at all levels.In Plasters/ mortars of proportion:
1 : 4 (1cement : 4coarse sand)
235
-
-
... More
Rain water duct treatment: Rain water pipes & ducts should be removed in a proper way so to remove the loose mortar from the brick joints and clean properly. Application of two coats of NITOCOTE CM210 an elastomeric cementitious coating, should be applied on the brick surface. plastering should be done by integral waterproofing liquid admixture for concrete and mortar CONPLAST WL
110
-
-
... More
Grouting :
Providing Grouting in R.C.C. walls & slabs by drilling holes @ 300mm c/c upto half of the wall depth in zigzag manner or as per drawings using a drill machine and fixing a nozzle of 20mm dia. for injecting a grout/ grout slurry till the refusal of injected grout material from adjacent nozzle (grouting operation pressure shall be in between 2 to 4kg per sq.cm.). Followed by cutting the exposed nozzle so as to make the wall free from the grouting pipes and to seal the gap with polymer modified mortar as specified and directed by the Department complete at all levels.
235
-
-
... More
False Ceiling (GYP-board) : (PLAIN COFFER)
Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) M/F Suspended Ceiling which includes G.I perimetre channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall / partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceililng angle of width 25mm x 10mm x 0.55mm thick fixed to soffit with G.I cleat and steel expansion fasteners.
Ceiling suspension of 0.55mm thickness having knurled web of 51.5mm and two equal flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip in direction perpendicular to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel with the help of connecting clip in direction perpendicular to the intermediate channel at 457mm c/c, 9.5 mm/ 12.5mm tapered edged Gypboard (conforming to IS : 2095 - 1982) is then screw fixed to ceiling section with 25mm long drywall screws at 230mm c/c. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally the board are to be jointed and finished so as to have a flush look which include filling and finishing the tapered and square edges of the boards with jointing compound, joint paper tape and two coats of dry wall topcoat suitale for Gypboard complete at all levels as specified and directed. (For light fittings, providing opening for doors, windows, ventilators etc. cut out made with frame of perimeter channel supported suitably to be measured and paid seperately where necessary).
12.5mm thick
315.65
-
-
... More
Supplying and installation of Armstrong Classic Lite A.tegular edge Ceiling system in the size of 600x600mmx16mm thick complete with 24mm Prelude suspension/framing system as per manufacturer's specifications.
92.88
-
-
... More
Proving 1mm laminate finish of approved brand over existing doors . All existing enamel paint will be removed
24
-
-
... More
TABLE WITH CREDENZA :
Providing and fixing work station having a size of 5’-6”X2’-0”X2’-6” in 25mm thk. Exterior Grade Block Board of approved make for table top and sides. . A Powder coated Wire manager, Key Board Drawer size 12” x 20” x2” deep made out of 12mm. thk. Ply ,Wooden Beading Patty four side in Laminate finish run on with Heavy duty sliding Chanel The Side credenza of size 2'-6"X1’-6”X2’-6”ht. in 19 mm BWP ply with drawers &openable shutters, size 1’-3”X1’-8”X2’-5” in 19 mm BWP ply with three drawers as per the drawing, finishing in 1 mm thk laminate of approved make and shade / design etc. complete. (Please check the Side credenza size as per layout to fit site condition).
10
-
-
... More
LOW HEIGHT PARTITION in BWP Ply & Laminate.
Providing and fixing Low ht. partition 4' high made out of 16 gauge 2" x 2" Alum. Framing at 2' C to C horizontally & vertically as directed or as per design / instructions. The 16 gauge aluminium angles cleats shall be used for joinery with aluminium metal screw. The aluminium framing then shall be covered with12mm.Thk. BWP ply of approved make finished in 1 mm thk laminate of approved make & shade. The Partition with Partly 10 mm thk clear float glass with four side teak wood mouldings. The partition top shall be provided with 80 mm wide x 12mm thick moulding patty in 2nd class Teak wood with Zink Polish matching Laminate colour. The rate also includes openable Flap door with locking arrangement as per requirement.
The necessary openings shall be provided in the partition for the Electrical/Telephone conduits & outlets as per design/instructions
21.64
-
-
... More
FULL HEIGHT STORAGE (7' HIGH X1'-6" DEEP)
Providing and fixing Built in storage made out of 19 mm thk BWP Grade Marine Ply 1'-6" deep, 6mm thk BWP Grade Marine Ply for the back, 1-1/4”thk. openable shutters with hinges as recommended & with laminate for all exposed surface &openable shutters in Laminate of approved colour. 19mm. removable shelves with laminate finish on both sides, edges shall be provided with leaping patties on all sides, at 16" spacing. All hinges, tower bolts, S.S Brush finish handles, ball-catches shall be of brass heavy duty. Complete with approved make Locks handles etc. complete as per design / instructions. All the shutters shall be made out of 12 mm.BWP Grade ply framing 80mm wide with 3 Nos. wide at middle horizontal and 2 vertical rails and then covered with 6 mm.BWP Grade marine ply from both sides with laminate on both sides of the shutter, as per design/instructions.
16
-
-
... More
LOW HEIGHT STORAGE (4' HIGH X 1'-6" DEEP)
Providing and fixing Built in storage made out of 19 mm thk BWP Grade Marine Ply 1'-6" deep, 6mm thk BWP Grade Marine Ply for the back, openable shutters with hinges as recommended & in Laminate of approved colour. 19mm. removable shelves with laminate finish on both sides edges shall be provided with leaping patties on all sides, at 16" spacing. All hinges, tower bolts, S.S Brush finish handles, ball-catches shall be of brass heavy duty.Complete with approved make Locks handles etc. complete as per design / instructions. All the shutters shall be made out of19 mm.BWP Grade ply with 1mm laminate on both sides Please note that all Internal & External Surface finished with approved colour Laminate , Rest as per design/instructions
2.4
-
-
... More
WALL HUNG STORAGE (2'-6" HIGH X 1'-0" DEEP)
Providing and fixing storage overhead made of 19mm thick exterior grade Phenol Formaldehyde bonded block board including providing 1.5mm thick laminated sheet in matt finished of approved make and shade including first class timber frame work. All exposed edges of the block are to be covered with Teak wood lipping as per design. Rate to including charges for brass hardware fittings as well as fixtures complete as per drawing. (Approx. size 300 mm depth and 750mm height.
6.6
-
-
... More
SOFT BOARD / NOTICE BOARD:
Providing and fixing Soft Board panelling (3’-0”X4’-0”) made out of 12mm thick Soft Board covered with approved colour felt/cloth (Rate Rs. 350/- ) on 6 mm.Thk. BWP Grade ply backing
2
-
-
... More
VENETIAN/VERTICAL BLINDS : Supply fitting and fixing of vertical blinds of Vista /Mac make to the windows & Glazed partition.
(a) Regular (iv) 50mm
12.24
-
-
... More
Providing and supplying Swivel Chair (Mid Back)
In MS frame covered with breathable Mesh in blackfor back & Lumber support, 12 mm Moulded ply for seat with PU on it. PU Adjustable arms, Chrome base,
Synchro mech. & Gas Lift etc. complete.
10
-
-
... More
Message Board /Pin -up Boards :
Supply & fixing message boards made of 12mm thick soft board with fixed over 12mm BWR plywood as backing finished with fabric (costing approx. Rs. 190/- per mts.) of approved texture, design and colour inculding cost of material, labour, necessary adhesive, screws etc. complete as directed by SBI /COnsultant fixed flush with surfaces of wall cladding wherever required
10
-
-
... More
LINEAR / RUNNING WORK STATION:
Providing and fixing linear / running Work Station having a size of 4’-0”X2’-0”X2’-6”ht. in 25 mm thk. Exterior Grade Block Board of approved make for table top and side supports. The Front apron in 12mm.thk. BWP ply with approved colour Laminate & on fixed Raised panel in 12mm. Thk. Finished In approved colour Laminate for all exposed surface,fixed with S.S. Studs & the top and sides of the counter to be finished on both sides with 1 mm thk. Laminate of approved make and shade / design. A Powder coated Wire manager ,Key Board Drawer size 12” x 20”x 2” deep made out of 12mm. thk. Ply ,Wooden Beading Patty four side in Laminate finish run on with Heavy duty sliding Chanel , A drawer unit of size 1’-4”X1’-8”X2’-5” in 19 mm BWP ply with three drawers as per the drawing etc complete .(Low height partitions abutting the counters will be paid separately&also Please Check the Counter Length during execution as per plan / Site Condition).
6.4
-
-
... More
CREDENZA UNIT / STORAGE (2'-6" HIGH X 1'-6"DEEP)
Providing and fixing CREDENZA Unit / storage made out of 19 mm thk BWP Ply 1'-6" deep, 6mm thk BWP Grade Ply for the back, 19mm thk.BWP Grade BWP ply with drawers &openable shutters with hinges as recommended & with laminate for all exposed surface, in Laminate of approved colour. 19mm. removable shelves with laminate finish on both sides, edges shall be provided with leaping patties on all sides, at 16" spacing. All hinges, tower bolts, S.S Brush finish handles, ball-catches shall be of brass heavy duty. Complete with approved make Locks handles etc. complete as per design / instructions.
4
-
-
... More
Providing and Fixing EGO LAMINATE WOODEN Flooring as per manufacturer's specification
70.46
-
-
... More
Varnishing two coats (excluding priming coat) on new wood and wood based surfaces under coating with flatting varnish and finishing coat with copal varnish or spar varnish to give an even surface including cleaning the surface of all dirt, dust and filling the knots, crack etc with specially made wood putty and sand papering so as to produce a smooth, dry and matt surface.
i) Surfaces over 100mm in width or girth
53
-
-
... More
Applying two coats of wood preservative oil, colourless (Burger Products) on new wood and wood based surface, after including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting.
38
-
-
... More
Supplying and instlation of Armstrong Wood Work laminate Plain Microlook edge Ceiling in the size of 600x600x18mm thick complete with 15mm Silhoutte suspension / framing system as per manufacturer's specifications.
6.48
-
-
... More
Providing amd fixing of wall paneling/cladding made of 1mm. Laminate to be fitted over 12mm. Thick commercial ply wood with a wooden frame work made of 40mm. X 50mm. wooden members to be placed @ 600mm. c/c both ways. The rate included three cots of french polishing over a coat of primer etc. comopleat any level.
141.11
-
-
... More
Message Board /Pin -up Boards :
Supply & fixing message boards made of 12mm thick soft board with fixed over 12mm BWR plywood as backing finished with fabric (costing approx. Rs. 190/- per mts.) of approved texture, design and colour inculding cost of material, labour, necessary adhesive, screws etc. complete as directed by SBI /COnsultant fixed flush with surfaces of wall cladding wherever required.
3.24
-
-
... More
Texture Paint on Walls
Providing and applying Spectrum aggragate laminate coating in the branded name of SPECTRUM with its all tools, plants and machineries and scaffolding etc as per manufactures guideline and specification of the product. A) Spectrum Naturaplast
12.15
-
-
... More
b) ARMSTRONG WOOD WORK LAMINATE CEILING SYSTEM Supplying and instlation of Armstrong Wood Work laminate Plain Microlook edge Ceiling in the size of 600x600x18mm thick complete with 15mm Silhoutte suspension / framing system as per manufacturer's specifications.
13.68
-
-
... More
Supplying fitting and fixing laminate suspended ceiling on meal frame with 12mm water proof plybase as per design complete with finishing as directed
23.83
-
-
... More
ARMSTRONG OPTRA WALL PANEL SYSTEM
Supplying and installation of Armstrong Optra Wall Panel system in the size of 600x600 x25mm thick complete with 77mm x 102mm Implaler suspension system as per manufacturer's specifications.
9.72
-
-
... More
Providing , fitting and fixing 450 mm deep and 750 / 2100 mm height contineous storage with shutters and with necessary hard ware with storage arrangement at bottom with middle self and shutter and locking arrangement a s per the detail drawing enclosed made of 18mm thick water proof exterior grade block board/MDF board of approved make with lamination 1mm thick on horizontal vertical surface of approved make and shade including fixtures , locks , handles polishing and painting, transportation etc. complete as directed.
a) 750mm ht (low hight)
14.85
-
-
... More
Vertical panelling on existing square columns / wall with 1st class timber frame and 12 mm water proof ply / MDF board finished with glass/texture paint/acrelic board/vineer panels of approved shade/pattern etc. complete.
10.29
-
-
... More
Supply and fixing of vertical blinds of Vista /Mac make to the windows & Glazed partition.
(a) Regular (iv) 50mm
15.84
-
-
... More
Supplying & making Planter box of size 450mmx450mm and height 450 mm with18 mm block board / MDF Board with top beading and outside teak vineering and lamination and with inside varnish/ painting
6
-
-
... More
DISPLAY UNIT
Providing and placing in position display units fabricated out of BWR 19mm block board/ 12mm thick BWR ply and finished with laminated / veneer as directed complete with 12mm glass shelves completed with varnishing
30
-
-
... More
Magnetic White Board : Supplying and fixing in position Magnetic White Board of size 1800 x 1200 with all accessories like magnetic Duster, Magnetic colour markers, etc of white mark or equivalent make all complete.
2
-
-
... More
Providing VITRIFIED floor tiles of approved quality, of specified size, shape and thickness not less than 12 mm on floors skirting risers and tread of steps over 15mm thick base of cement mortar in Prop 1.3 (1cement : 3 coarse sand) including cutting where necessary finished with flush pointing with Fax -A-Tile (choksey / Sika / Pedelite / Rouf) white cement slurry mixed with approved pigment to match the shade of the shade of the tiles complete at all level as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Architect)
a) Premium Range (Size 600mm x 600mm) RAK / NITCO / JOHNSON (Double fired nano technology) c)( Delux Range (Size 1000mm x 1000mm - RAK/Somany/Orient / NITCO/Vermora / JOHNSON)
52.2
-
-
... More
Providing melamyne / PU protective and decorative coating for wood and veneer works to bring a natural finish complete using AP thinner with the spraying procedure to bring matt or gloss finish (Asian Paints)
30
-
-
... More
DISPLAY UNIT
FURNITURE, CHAIRS AND OTHER ACCESSORIES
Providing and supplying contemporary chic design centre table (Durian/equivalent make Cat. No. ZEE/YUBONG with clear tempered glass top and clear tempered glass shelf or 1 wooden shelf and 1 drawer below the top
1
-
-
... More
Providing and supplying single seater pure leather sofa of durian-AQILA-31802/castle-X / equivalent for Director's Room
2
-
-
... More
Providing and supplying two-seater pure leather sofa of durian
/castle-X / equivalent
2
-
-
... More
Providing and Fixing rubberite hollow mat at the entrance of size 5 feet x 3 feet -- 3 inch
1
-
-
... More
Providing and fixing Durosoft door mat for Main Entrance Door
b) 2 feet x 4 feet & 0 inch
1
-
-
... More
Service Trolly out of Teak Wood/ brass
1
-
-
... More
Removal of existing electrical wiring & fitting from conference hall , directors roomoffice space and corridor & lobby area
1
-
-
... More
Removal of fire fighting system from conference hall , directors roomoffice space and corridor & lobby area
1
-
-
... More
Removal of existing celing wall cladding etc from conference hall , directors roomoffice space and corridor & lobby area
1
-
-
... More
Supply, Installation, Testing, Commission of Loop card for Addressable Panels make- MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)
1
-
-
... More
Supply, installation, testing & commissioning of Network Card/RS 232 Communication Board etc complete.make- MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)
1
-
-
... More
Supply, Installation, Testing, Commission of Addressable Semi Flush Mounting Resettable (NonBreaking Glass) MCP, Supplied with Special Reset Tool BRAND : MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)
4
-
-
... More
Supply, Installation, Testing, Commission of Network Card / RS 232 Communication Board
1
-
-
... More
Supply, Installation, Testing, Commission of Intelligent Addressable Optical Detector with Remote Indicator Output With Base BRAND : MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)
63
-
-
... More
Supply, Installation, Testing, Commission of Addressable Wall Mounting Sounder / Hooter Cum Strobe Brand : MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)
4
-
-
... More
Supply, Installation, Testing, Commission of Addressable Input / Ouput Module Brand : MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)
1
-
-
... More
Supply, Installation, Testing, Commission of Addressable Loop Isolator Brand : MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)
4
-
-
... More
Supply & fixing of 2X1.5sq. mm. PVC insulated copper Armoured Cable on surface/ recess/ above false ceiling etc. as required. (ISI marked) )
360
-
-
... More
Clearance of service septic tank and removing the night soil and debris etc. manually from thetank/chamber to a distant place preferably during holidays or at night by bailing out the deposited night soil,buring the same in nearby trenches /pits which has been dug earlier and covering the same.The service septic tank is cleaned with clear water and completed asdirected by the Department.
(a) For 200 users
1
-
-
... More
Clearance of service septic tank and removing the night soil and debris etc. manually from thetank/chamber to a distant place preferably during holidays or at night by bailing out the deposited night soil,buring the same in nearby trenches /pits which has been dug earlier and covering the same.The service septic tank is cleaned with clear water and completed asdirected by the Department.
(a) For 100 users
2
-
-
... More
Cleaning & clearing the inspection chamber whichis partly filled with night soil connected to septic tank soak pit with both side soil pipe of length1.80m manually and disposed off the block by pushing with bamboo kamis as directed by the Department.
16
-
-
... More
Removing and refilling old G.I. Pipes of 15mm dia with new socket, bend, tee etc. complete including the stacking the old serviceable materials at safe place as directed.
171
-
-
... More
Indian type W.C Orissa pattern of size 580 x 440 mm
a) White
i) Parryware make
18
-
-
... More
Renewing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately)
a) White
(iii) Universal Closet P Trap (Cat No.C0272) (inclusive of seat cover)
18
-
-
... More
Renewing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately)
i) Parryware make
a) White
(i)Economy Single Flush (Cat No.C8090/C8055)
18
-
-
... More
Removing and refilling old G.I. Pipes of 20mm dia with new socket, bend, tee etc. complete including the stacking of old serviceable materials at safe place as directed.
61
-
-
... More
Removing and refilling old G.I. Pipes of 25mm dia with new socket, bend, tee etc. complete including the stacking of old serviceable materials at safe place as directed.
75
-
-
... More
Removing and refilling old G.I. Pipes of 32mm dia with new socket, bend, tee etc. complete including the stacking of old serviceable materials at safe place as directed.
33
-
-
... More
Removing and refilling old G.I. Pipes of 40mm dia with new socket, bend, tee etc. complete including the stacking of old serviceable materials at safe place as directed.
28
-
-
... More
Removing and refilling old G.I. Pipes of 50mm dia with new socket, bend, tee etc. complete including the stacking of old serviceable material at safe place as directed
28
-
-
... More
Removing and refilling old G.I. Pipes of 80mm dia with new socket, bend, tee etc. complete including the stacking of old serviceable materials at safe place as directed.
17
-
-
... More
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mn gap for thermal exapansion .(i) Single socketed pipes.
110 mm diameter
80
-
-
... More
Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :15.42.1 75 to 80 mm dia pipe
105
-
-
... More
Taking out C.I. cover with frame from R.C.C. top slab of inspection chambers of various sizes including demolishing of R.C.C. work manually/ by mechanical means and stacking of useful materials
near the site and disposal of unserviceable materials within 50 metres lead as per direction of Engineer-in-charge.
16
-
-
... More
Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.
52
-
-
... More
Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.
INDIAN TYPE WATER CLOSET
Providing fitting and fixing vitreous water closet squatting pan (Indian type W.C Orissa pattern) with all fittings and fixtures complete including cutting and making good to the walls and floors whereever required. (Flushing Cistern to be paid separately)
Indian type W.C Orissa pattern of size 580 x 440 mm a) White
iii) Jaquar make
3
-
-
... More
EUROPEAN TYPE WATER CLOSET
Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 415mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (including flusing listern)
C) Jaquar make
a) White
(Bowl for couple closet with soft closing seat cover
Size 660 x 415 x 830 s, trap-220 mm (CNS-WHT-75155 Including Cistern CNS-WHT-201)
16
-
-
... More
Providing fitting and fixing Vitreous china wall hang water closet (European type W.C pan 400mm high) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately)
iii) Jaquar make
a) White
(II)Solo (Cat. No.SLS-WHT-6951)Size 515x370x400 ) (inclusive of seat cover and fittings)
Supplying, fiting and fixing Flush Valves
ii) Jaquar Make
1
-
-
... More
Metropole Flush value Dual Flow 40 mm size ( concealed body ) with concealed sheet off provision & rectangular dual Flush plate ABS chrome Plated (3.0/6.0 ltspen flushing) code no Flv-1089 DFP
FLV-1089 DFP
1
-
-
... More
URINAL
Providing fitting and fixing vitreous china flat back type lipped front urinal basin of with automatic flushing cistern with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required.
C) Jaquar make
a) White
(i) Urinal (Cat. No.URS-WHT-0704) with Sensor (Cat. No.SNR-CHR-51097)
18
-
-
... More
DIVISION PLATE
(a) White
division plate 680x300 (Cat.No.61001)
11
-
-
... More
WASH BASIN
Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately)
Wall Hang Basin
(C) Jaquar Make
(i) Cat. No.CNS-WHT-WB04 (550 x 400 x 198)
14
-
-
... More
Table Top Basin
(C) Jaquar Make
(ii) Solo (Cat. No. SLS-WHT-0558)
1
-
-
... More
Under Counter Basin
(C) Jaquar Make
(i) Continental (Cat. No. CNS-WHT-705)
13
-
-
... More
MIRROR
Providing fitting and fixing Decorative Mirror complete as directed and specified.
(B)Parryware Make (a)Size 800mm x 600 mm
1
-
-
... More
(b) size 600mmx450mm
45
-
-
... More
SHELF
Providing fitting and fixing Glass Shelf complete as directed and specified.
Glass shelf with C.P. guard rail (iii) Jaquar make
(a) Continental 550 mm long (Cat. No.ACN-1171N)
27
-
-
... More
(c) Kubix 600mm long (Cat. No.AKB-35771P)
SOAP TRAY,SOAP DISH,LIQUID SOAP DISPENSER AND LIQUID SOAP CONTAINER
(i) Jaquar Make
1
-
-
... More
Providing, fitting and fixing Liquid soap dispenser and liquid soap container complete as directed and specified.
(i) Jaquar Make
(b) Continental (Cat.No.ACN-1133N) (soap dispenser with glam bottle)
27
-
-
... More
(c) Kubix with glass bottle (Cat. No.AKB-35735)
1
-
-
... More
TOWEL RAIL,TOWEL RACK & TOWEL RING
Providing, fitting and fixing CP towel rail complete as directed and specified.
(a) Jaquar make (ii) Continental 600mm (Cat.No. ACN-1111N)
5
-
-
... More
(vi) Kubix- Grab bar (300mm long) (Cat.No.AKB-35701)
2
-
-
... More
(vii) Kubix (600mm long) (Cat.No.AKB-35711)
1
-
-
... More
Providing, fitting and fixing Chrome Plated towel rack complete as directed and specified.
(a) Jaquar make (vii) Kubix (600mm long) without lower hanger (Cat.No.AKB-35781F)
1
-
-
... More
Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified.
(a) Jaquar make (i) Continental towel ring square (Cat.No. ACN-1121)
27
-
-
... More
(iv) Kubix towel ring square (Cat.No.AKB-35721)
1
-
-
... More
CHROME PLATED ROBE HOOK
Providing, fitting and fixing Chrome Plated robe hook complete as directed and specified.
(a) Jaquar make (i) Continental (Cat.No. ACN-1191N)
19
-
-
... More
(iv) Kubix (Cat.No.AKP-CHR-35791P)
1
-
-
... More
TOILET PAPER HOLDER
Providing, fitting and fixing Chrome Plated TOILET PAPER holder complete as directed and specified.
(a) Jaquar make (i) Continental toilet paper holder (Cat.No. ACN-1151N)
19
-
-
... More
(vii) Kubix toilet roll holder with Flap (Cat.No.AKB-CHR-35753P)
1
-
-
... More
WASTE COUPLING
Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified.
(a) Jaquar Make
(i) 32mm (HT/FT) (Cat.No.ALD-705 / 709)
28
-
-
... More
BOTTLE TRAP
Providing, fitting and fixing Chrome Plated bottle trap complete as directed and specified.
(a) Jaquar make (ii) Bottle trap (with internal partition) 32mm size with 300mm long wall connection pipe (Cat.No. ALD-769B)
28
-
-
... More
PVC PIPES,BENDS,JUNCTIONS,TEES ETC.
Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.
510.2
-
-
... More
(iv) 75mm dia.
271.2
-
-
... More
b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.
(ii) 110mm dia.
99.26
-
-
... More
(iv) 75mm dia.
10
-
-
... More
Supplying fiting and fixing 45degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.
7
-
-
... More
(iv) 75 mm dia.
3
-
-
... More
b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.
(ii) 110mm dia.
30
-
-
... More
(iv) 75 mm dia.
10
-
-
... More
Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.
6
-
-
... More
(iv) 75 mm dia.
2
-
-
... More
b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.
(ii) 110mm dia.
11
-
-
... More
(iv) 75 mm dia.
2
-
-
... More
Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.
10
-
-
... More
(iv) 75 mm dia.
2
-
-
... More
b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.
(ii) 110mm dia.
2
-
-
... More
(iv) 75 mm dia.
2
-
-
... More
Supplying fiting and fixing PVC single ‘Y’ of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.
5
-
-
... More
(iv) 75 mm dia.
2
-
-
... More
b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.
(ii) 110mm dia.
2
-
-
... More
(iv) 75 mm dia.
2
-
-
... More
Supplying fiting and fixing PVC single ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.
a) In exposed surfaces or in trenches. (i) 110mm dia.
4
-
-
... More
Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 110 mm x 75mm
16
-
-
... More
b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.
(iv) 110 mm x 75mm
5
-
-
... More
GRATING
Providing fiting & fixing (300x230)mm C.I. yard gully hinged Grating complete as directed and specified.
C.P. Grating (ii) 110mm dia
69
-
-
... More
MANHOLE COVER
Providing fitting and fixing (600x600)mm 90mm thick C.I. Man hole cover and frame of 25 Kg. weight complete as directed and specified
4
-
-
... More
SOAK PIT AND INSPECTION CHAMBER
Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.
6
-
-
... More
AJAY FLOWGUARD CPVC PIPE
Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and specified.
(Note: Ball valve and union will be charged extra and does not comes under Accessories)
(i) In internal wall - exposed on wall
(d) 32 mm OD
23
-
-
... More
(e) 40 mm OD
9
-
-
... More
(f) 50 mm OD
6
-
-
... More
(ii) Concealed by chiselling or breaking brick wall/C.C/R.C.C and making good to damages
(a) 15 mm OD
123
-
-
... More
(b) 20 mm OD
20
-
-
... More
(c) 25 mm OD
5
-
-
... More
Providing fitting and fixingJaquar make allied hand shower (health faucet) with imetre long easy flex tube in chorme finish & wall look cat no ALD-CHR-565
17
-
-
... More
BIB COCK
Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) Jaquare make
(a)Continental /Clarion
(iii)2-Way bib cock
16
-
-
... More
(b) Kubix-350- F/QUARTER Turn
ii)way bibcock with wall flange (KUB-35041f)
1
-
-
... More
STOP COCK
Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) Jaquar (a) Continental / Clarion
(ii)15mm dia( Angular stop cock )
(b)Kubix-F
64
-
-
... More
(i) Angular stop cock with wall flange(Kub-35053F)
2
-
-
... More
PILLAR COCK
Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. Jaguar make (a) Continental
16
-
-
... More
(b) SNR-CHR-51027 SENSOR FAUCET FOR WASH BASIN (director)
1
-
-
... More
VALVE
Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed.
a) 50mm dia
3
-
-
... More
b) 40 mm dia.
3
-
-
... More
c) 25 mm dia.
11
-
-
... More
Supplying and fitting ball valve as specified and directed..
a) 25 mm dia. (gun metal)
5
-
-
... More
b) 20mm dia. (gun metal/Copper)
2
-
-
... More
Supplying fitting and fixing gun metal check valve including necessary threads to pipes.
a) 50 mm dia (Heavy type)
2
-
-
... More
b) 40 mm dia (Heavy type)
2
-
-
... More
Supplying fitting and fixing G.I. Foot valve with strainer including cutting necessary threads to pipes. a) 50 mm dia (Heavy type)
1
-
-
... More
b) 40 mm dia (Heavy type)
1
-
-
... More
Providing fiting & fixing C.I. Grating to the floors complete as directed and specified.
110mm dia
6
-
-
... More
Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately)
Without pedestal
Parryware Make
White
Tapil Basin 500 x360
20
-
-
... More
Providing, fitting and fixing CP towel rail complete as directed and specified.
Sona make Towel rail Diplomat 600mm long (Cat.No.TR-0605)
18
-
-
... More
Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified.
Sona Make
Soap dish light (cat no. TR-0661
18
-
-
... More
Providing, fitting and fixing Chrome Plated robe hook complete as directed and specified.
Agmeco make Dolfee (Cat.No.DE-00211)
18
-
-
... More
Providing fitting and fixing 450mm dia. 90mm thick C.I. Man hole cover and frame of 38 Kg. weight complete as directed and specified.
2
-
-
... More
Providing, fitting and fixing Chrome Plated bottle trap complete as directed and specified.
Sona make Bottle trap indian 40mm (Cat. No.BT-0751)
18
-
-
... More
In concealed surfaces or in trenches. 110mm dia
78
-
-
... More
75 mm dia
27
-
-
... More
Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. In exposed surfaces or in trenches.
110mm dia
12
-
-
... More
Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. In exposed surfaces or in trenches.
110mm dia
4
-
-
... More
Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. 75mm dia. PVC cowel of ISI make
6
-
-
... More
Providing and fixing Chlorinated Polyvinyle Chloride (CPVC) Pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. The includes jointing of pipe
c) 25 mm nominal outer dia pipe
20.8
-
-
... More
d) 32 mm nominal outer dia pipe
30
-
-
... More
(B) Concealed pipe with cutting chases & making good the walls
a) 15 mm nominal outer dia pipe
82.8
-
-
... More
b) 20 mm nominal outer dia pipe
23.4
-
-
... More
Supplying fitting and fixing C.P bib cock 15mm dia of approved brand directed and specified.(G.I & C.P pipes will be measured separately).
Essco make (Delux/Sumthing spl/Tropical)
Bib cock short body
18
-
-
... More
Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) Sona Brand.
15 mm dia Concealed Stop Cock
36
-
-
... More
Supplying and Fitting C.P Pillar Cock of 15mm dia of approved brand as specified and directed. Sona make
Heavy Type
18
-
-
... More
Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately)
Parry ware make
White
Petite (SLP) CAT No. c0287/88
18
-
-
... More
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes. 110 mm diameter
40
-
-
... More
Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately)
parryware make
White Economy single flush (cat no C8090/c 8055)
18
-
-
... More
Supplying fitting and fixing overhead adjustable Chrome Plated (C.P.) spray shower 15mm dia. of Sona make with wall flange as directed and specified.(pipes will be measured and paid separately)
a) supreme shower with arm
18
-
-
... More
Wiring in surface/ recessed PVC conduit FR (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) cable
Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 20mm dia 2mm thick / heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) complete
Short point up to 3.00 metre. length.
24
-
-
... More
Medium point up to 6.00 metre. Length.
35
-
-
... More
Long point up to 10.00 metre. Length.
44
-
-
... More
Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.)
Long point up to 10.00 metre. Length.
27
-
-
... More
Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete.
Long point up to 10.00 metre. Length.
28
-
-
... More
Wiring for 5 pin 6 amp plug with 1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) including 5 pin 6 amp socket outlet (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.)make) and 6 amp flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.)make) earthing the 3rd pin of the socket as required on the switch board in surface/ recessed P.V.C. conduit wiring system. When fitted on same board of light and fan.
30
-
-
... More
Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system.
With 2 x 1.5 sq. mm. cable in 20 mm dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.
345
-
-
... More
Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system.
With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.
970
-
-
... More
With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. cable in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.
25
-
-
... More
With 2 x 6 sq. mm. + earth continuity with 1x 4 sq. mm. cable in 25 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.
215
-
-
... More
Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system.
With 4x 6 sq. mm. + earth continuity with 2x4 sq. mm. cable in 32 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.
30
-
-
... More
With 4 x 10 sq. mm. + earth continuity with 2x6 sq. mm. cable in 40 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.
150
-
-
... More
FITING AND ACCESSORIES
Fitting and fixing of brackets on the wall in GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover with all accessories such as GI/ MS switch board (ISI marked) with phenolic laminated sheet cover including connection as approved by the Deptt.)as required complete.
SWITCH GEAR & PROTECTION
INDUSTRIAL SOCKETS, DB WITHOUT MCB & MCCB , MCB, RCCB,RCBO, SFU, CHANGE OVER ETC. (C&S, Havells, INDOASIAN, HPL OR EQUIVALENT as approved by the Deptt.)MAKE)
1
-
-
... More
Supplying fitting and fixing industrial Plug & Socket in surface mounting SPN sheet steel powder painted MCB DB incorporated with MCB DIN rail, neutral link Earth bar of the following rating of DP MCB complete with making necessary connection etc. as specified and directed by the Deptt.
25A Capacity. (C&S, Havells, INDOASIAN, HPL or equivalent as approved by the Deptt.)make)
4
-
-
... More
MCB DB (ABB, SCHNEIDER MG, LEGRAND, HAGER MAKE) &(SCHNEIDER NEO BREAK, C&S, Havells, INDOASIAN, HPL OREQUIVALENT MAKE AS PPROVED BY THE DEPTT.)
Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt.
12 way SPN double door
7
-
-
... More
Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 double door surface mounting TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt.
ABB, Schneider MG, legrand, Hager make)
4 way TPN (4+12) double door
3
-
-
... More
MCB, MCCB, RCCB, RCBO (ABB, SCHNEIDER MG, LEGRAND, AND HAGER MAKE) & (SCHNEIDER NEO BREAK, C&S, Havells, INDO ASIAN, HPL OR EQUIVALENT MAKE AS PPROVED BY THE DEPTT.) MCB (Conform to IS / IEC 60898-1:200/ MCCB (Conform to IS/IEC 60947- RCCB (Conform to IS/IEC 12640 / 61008)
Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.
C Series(Schneider MG, legrand, Hager make)
6 to 32A
84
-
-
... More
Supplying with fitting and fixing DP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.
C Series(ABB, Schneider MG, legrand, Hager make)
6 to 32A
5
-
-
... More
40A
1
-
-
... More
Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.
C Series (ABB, Schneider MG, legrand, Hager make)
40A
4
-
-
... More
Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.
30mA sensitivity DP RCCB(ABB, Schneider MG, legrand, Hager make)
25A
5
-
-
... More
100/300mA sensitivity DP RCCB(ABB, Schneider MG, legrand, Hager make)
25A
2
-
-
... More
Supplying with fitting fixing of 6 amp one way modular clip in bell push MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.
1
-
-
... More
Supplying including installation of socket outlet 10/16 Amps 3/5 pin combine shuttered complete , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.
15
-
-
... More
Supplying including installation of socket outlet 6/10/13 Amps INTERNATIONAL SOCKET , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.
66
-
-
... More
Supplying with fitting fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.
29
-
-
... More
Supplying with fitting fixing of 6/10 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.
119
-
-
... More
Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department.
1-2 module type Metal
14
-
-
... More
3 module type Metal
24
-
-
... More
6 module type Metal
14
-
-
... More
8 module type Metal
6
-
-
... More
9 module type Metal
3
-
-
... More
12 module type Metal
7
-
-
... More
18 module type Metal
2
-
-
... More
Supplying including fitting fixing of following MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department.
2 module
14
-
-
... More
3 module
24
-
-
... More
6 module
14
-
-
... More
8 module
6
-
-
... More
9 module
3
-
-
... More
12 module
7
-
-
... More
18 module
2
-
-
... More
Supplying with fitting fixing of blank plate single in modular switch system , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.
48
-
-
... More
Supplying with fitting and fixing of 25A Modular Motor Starter 2M , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.
6
-
-
... More
CEILING FAN, EXHAUST FAN AND AIR CURTAIN
Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department.
Domestic
Trans Air 300 mm sweep (Crompton make)
1
-
-
... More
Supplying including fitting fixing of following A.C. Wall fan in the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department.
Swing platina with plastic blade, 400 mm sweep
INVERTER/ UPS AND RACK FOR LAN WORKS/ LAN WORKS/AVR
Supplying including installation of UPS
13
-
-
... More
2 KVA On-Line UPS System (Orion or equivalent make as approved by the Deptt.) with PWM-IGBT technology230V AC Input (160V – 280V A 1 Ph input- 1 Ph outputWith Isolation Transformer1.6KW output with 0.8 output PF30 min backup using SMF battery
2
-
-
... More
APWD Luminaires approved by CE New
Supplying, installation, testing and Commission of the following indoor Decorative Surface mounted 2' x 2' LED down lighter luminaries of model no-SM365C LED 32 -6500 PSU OD GR / SM365C LED 32 -6500 PSU OD GH / SM365C LED 32 -6500 PSU OD GR /SM365C LED 32 -6500 PSU OD WH/ LSVR01S036SC / LSVR01S0365SN / LSVR01S0365SW/ CRCO10S038HP57G1 complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips / Jaquar / Wipro make).
50
-
-
... More
Supplying, installation, testing and Commission of the following indoor Decorative Recess mounted LED down lighter luminaries of model no-LESP01R009XC / LESP01R009XN /LESP01R009XW / L00957R000 / L00940R000 / L00930R000 /LD90-111 - XXX-65-XX complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make).
22
-
-
... More
Supplying, installation, testing and Commission of the following indoor Decorative Recess mounted LED down lighter luminaries of model no-DN 393 B LED 12 S-6500 PSU WH / D01257R000 / D01240R000 / D01230R000 / CRDL11R017HP57 complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make).
57
-
-
... More
Supplying fitting & fixing of LED Bulb non-dimmable in the existing batten / angle holder as required and as directed by the department ( Jaquar or eqvt. make).
Prima Series Bulb 9W
1
-
-
... More
Supplying fitting & fixing of LED Kubik Batten tube light fitting 300mm length as required and as directed by the department ( Jaquar or eqvt. make).
kubik Series Batten tube fitting 6W
1
-
-
... More
Supplying, installation, testing and Commission of the indoor Decorative LED Recess-mounted, white powder-coated CRCA housing with full mounted acrylic diffuser (1ft x 4ft) of make Jaquar Model Ultima Cat No. LULT04S036XN or equivalent complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make).
6
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements