Guwahati Metropolitan Development Authority Tender
... More
The GMDA has issued a formal invitation for competitive bids for the Guwahati Metropolitan Development Authority project, for Development Of Blue Green Infrastructure in Kamrup Metro, Assam, with an estimated contract value of Rs. 30,11,51,441. The bid opening date for this tender is 04-06-2025 and the last date for bid submission is 27-06-2025. Interested bidders for Guwahati Metropolitan Development Authority tender can download the important documents here to check the scope of work, eligibility criteria and technical requirements.
Guwahati Metropolitan Development Authority - GMDA Tender
Bridge Construction
Eprocure
Opening Date4 Jun 2025
Closing Date27 Jun 2025
Tender Amount₹ 30,11,51,441
Technical
Technical
Financial
Additional Eligibility
Bid Capacity
... View More
The formula for Assessed Available Bid Capacity is A x N x 2 - B.
Technical Capacity
... View More
The bidder is required to have prior work experience in building construction and electrical works. Specifically, they should have satisfactorily completed at least one similar work of Govt. Office/building/roads of construction of value not less than Rs. 24,09,21,153.00, which is 80% of the value of contract/contracts, and two similar work of Govt. Office/building/roads of construction of value not less than Rs. 15,05,75,720.00, which is 50% of the value of contract/contracts. For electrical works, the bidder (or its sub-contractor, if any) should have executed similar electrical works for a minimum amount of Rs. 10.00 lakhs (Rupees Ten Lakhs) in any one of the last 5 (five) financial years in a single job. The value of the contract/contracts is mentioned as Seventy Five Thousand Seven Hundred Twenty, which is 50% of the total value. The bidder should also provide information on their existing commitments and ongoing works, including the value of works remaining to be completed, and the stipulated period of completion. The value of existing commitments and ongoing works should be provided, along with a certificate issued by the Engineer-in-Charge, not below the rank of an Executive Engineer or equivalent. Additionally, the bidder should provide information on their annual financial turnover for the last five years, with the amount specified in Rs. Cr. A certificate issued by a Chartered Accountant should be attached to support this information. The bidder should have an undertaking for investment of minimum cash up to 25% of the value of the work. Evidence of access to or availability of credit facilities, certified by the bankers, with a minimum of 10% of the notified contract value, should also be provided. The bidder should also have minimum liquid assets/credit facility of Rs. 6,02,030,288.00, which is 20% of the notified contract value.
Costs
EMD
₹ 60,23,029Document Cost
₹ 30,000Tender Fee
Refer Documents
Summary
Development Of Blue Green Infrastructure
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2025_GMDA_44724_1Tender No
GMDA/DEV/14/2025/21Tender Authority
Guwahati Metropolitan Development Authority ViewPurchaser Address
-Website
http://https://gmda.assam.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.
2402
-
-
... More
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.
In cement mortar
561.23
-
-
... More
Dismantling steel work in built up sections in angles, tees, flats andchannels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.
28080.925
-
-
... More
Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.
240
-
-
... More
Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:
15.28.1 G.S. Sheet
2000
-
-
... More
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent
design mix)
110.7
-
-
... More
Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as
approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.
1210.58
-
-
... More
Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil
15604.76
-
-
... More
Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.
1170.357
-
-
... More
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
155215.597
-
-
... More
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25
5292.31
-
-
... More
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources)
1524.01
-
-
... More
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)
542.975
-
-
... More
Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete
1252.8
-
-
... More
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
53279.42
-
-
... More
Brick work with common burnt clay F.P.S. ( non modular) bricks of class destination 7.5 in foundation and plinth in:
Cement mortar 1:4 (1 cement :4 coarse sand)
1494.22
-
-
... More
Coursed rubble masonry (first sort) with hard stone in foundation and plinth with : 7.6.1 Cement mortar 1:6 (1 cement : 6 coarse sand)
121.5
-
-
... More
Ruled / Flush pointing on Brick / stone masonry surface with lime, surkhi and Brick dust mortar in the ratio of 1:1.5:1/2 {One lime: 1.5 surkhi (70% red and 30% light yellow surkhi ) : 1/2 brick dust}. (The rate is inclusive of all materials & labours & scaffolding upto 25mtr height).
144
-
-
... More
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes
1972
-
-
... More
Providing and fixing S.S. ERW P hollow section of various thickness and sizes in square, rectanular and round shape from 25mm to 450mm section including frame of grade 304 pipes with braces of S.S. grade 304 and rectangular section including cutting, organ welding, grading, making circustances polishing, buffing etc. complete with necessary holes, nuts & bolts, caps & anchor plates of S.S. grade 304 ASTM as per drawing & instructionsof the Engineer-in-charge excluding the cost of RCC/CC and earth work.
3859.1
-
-
... More
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-harge. The sheet shall be fixed using self drilling /self tapping
screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
3000
-
-
... More
Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
400
-
-
... More
Providing & making Gabion structure with Mechanically Woven Double Twisted Hexagonal Shaped Wire mesh Gabion Boxes as per IS 16014:2012,MORTH Clause 2500, of required size, Mesh Type 10x12 (D=100 mm with tolerance of ± 2%) Zinc coated, Mesh wire diameter 3.0 mm, mechanically edged/selvedged with partitions at every 1m interval and shall have minimum 10 numbers of openings per meter of mesh perpendicular to twist, tying with lacing wire of diameter 2.2mm, supplied @ 3% by weight of Gabion boxes, filled with boulders with least dimension of 200 mm, as per drawing, all complete as per direction of Engineer-in-charge.
4125
-
-
... More
12mm cement plaster of mix; 1:6 ( 1 cement : 6 coarse sand )
9594
-
-
... More
Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of water proofing cement paint applied @ 2.20kg/10 sqm.
280
-
-
... More
Finishing walls with textured exterior paint of required shade : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
280
-
-
... More
Finishing walls with textured exterior paint of required shade : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
280
-
-
... More
Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made table vibratory method using PU mould, laid in required colour & pattern over 20mm thick mortar, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge; 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.
13800
-
-
... More
Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made table vibratory method using PU mould, laid in required colour & pattern over 20mm thick mortar, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge; 80mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.
4560
-
-
... More
Turf pavers (500x500x80mm)
2300
-
-
... More
Providing and laying flamed/ lapato finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 40 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed / lapoto/shot blasted finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
400
-
-
... More
Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge.
200
-
-
... More
Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.
300
-
-
... More
Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : 8.14.3 White sand stone - exposed face fine dressed with rough backing . 8.14.3.1 70 mm thick
645
-
-
... More
Extra labour for Chiselling in approved patterns and texts
5
-
-
... More
Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 laid over and jointed with grey cement slurry including rubbing and polishing etc. complete. (B) 30 mm thick ( Brown & Grey Colour)
10000
-
-
... More
Providing, laying, spreading fine sand of zone IV, complete as per specifications and directions of Engineer-in-Charge.
540
-
-
... More
Providing, laying, and fixing in place Epdm Flooring of approved colour and pattern , complete as per specifications and directions of Engineer-in-Charge.
85
-
-
... More
Supplying, filling, spreading & leveling gravels / Pebbles / Bajri of size range 20 mm to 150 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
1800
-
-
... More
Supplying, filling, spreading & leveling stone boulders of size range 100 cm to 600 cm, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. ( Rough edge and River washed)
1440
-
-
... More
Supply and fixing factory made solid 25mm thick WPC panel (Wood Polymer Composite) of approved design as per the dimensions provided. WPC is composed of rice and wheat husk with thermo plastic single extruded, which should be termite proof, water proof, fire retardant ( Grade A) and Screwable having 1400 N screw holding capacity on the face and 1100N on edge, of approved make with UV stabilizers, which makes it 100% exterior grade. Material to be of density 550 kgs/cum. With GRIHA Council certification. The WPC panel shall be fixed on metal frame work (metal frame work shall be paid separately under relavant item head) with aluminium clamps/studs/rivets/bolts of suitable size as per manufacturer's specification. The contractor shall get the sample approved from competent authority prior to start of execution. Rate are inclusive of all labour, tool & plant,machineries, work at any height and complete in all respects and as per direction of Engineer-in-charge.
880
-
-
... More
Supply providing and fixing of IPE Wood flooring made up of teak wood, complete work in cluding T&P and materials complete work as per the drawings and the directions of engineer in charge.
150
-
-
... More
Supplying & laying of bi-axial extruded high modulus polypropylene geogrid coforming to MORTH SPECIFICATION for base/sub-base reinforcement having minimum tensile strength 15kN/m in the longitudinal and transverse direction, with 5kN/m and 7kN/m tensile strength at 2% and 5% strain respectively in the longitudinal and transverse direction, junction efficiency not less than 95% and with 38mm X 38mm mesh opening.
24000
-
-
... More
Supplying, filling, spreading & leveling murrum, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
480
-
-
... More
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
576
-
-
... More
40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints finished flush. White Sand Stone
13000
-
-
... More
Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).
180
-
-
... More
Precasting and placing in position Bollards of required shape and size including providing M.S. Pipe Sleeve 50 mm dia 300 mm long in the Bollard and M.S. Pipes 40 mm dia and 450mm long with 150x150x6mm M.S. plate welded at bottom and embedded 150mm in cement concrete 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources), including necessary excavation of size 250x250x450mm deep for the same in bitumen/concrete pavement at specified spacing.
50
-
-
... More
Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete
19.36.1 450 mm dia RCC pipes.pe
1000
-
-
... More
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 18.35.1 With common burnt clay F.P.S.(non modular) bricks ofclass designation 7.5. Inside size 120x90 cm and 90 cm deep including Resessed MS cover with frame (medium duty) 500 mm internal diameter, : 19.7.2.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
35
-
-
... More
Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 19.21.3 For pipes 350 to 450 mm diameter
17
-
-
... More
Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : 19.27.1 With common burnt clay F.P.S. (non modular) bricks of
class designation 7.5
30
-
-
... More
Providing and fixing acrylic plastic sheet panels of approved quality in required thickness plain clear or any colour or obscured linings in lieu of glass pans to doors/windows including providing and fixing clips, putty etc. complete. (b) 3.00 mm thick.
150
-
-
... More
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
350
-
-
... More
Supply & Installation of MS CNC Laser Cut Panel of below mention thickness, Aesthetic fixture made of MS, as per design & drawing given by architect. Item include cost of ms sheet, cutting & installation on site. All work to be completed as per instruction of Site in charge.
100
-
-
... More
Supply and fixing of 10mm multiwall clear Polycarbonate sheet, aluminium profile, aluminium L Angle, Screws, Sealants and fixing accessories
150
-
-
... More
Providing and fixing SS DOUBLE POLE 14X24 INCH GRADE 202, WEIGHT 13.000 KG APPROX. CAPACITY 60+60 LTR OPEN TYPE SHEET THICKNESS 0.5 mm APPROX.
10
-
-
... More
Providing & fixing in position Phenol bonded Bamboo wood in wall skirting with planks of sizes 14mm thick, 1900mm length (minimum) and 85mm wide(minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The skirting shall be fixed with SS screws & rawl plugs, over underlayment of 4mm thick, expanded polyethylene foam sheets having 40kg/cum density over prepared surface. The bamboowood planks shall have minimum density of 1000Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.
591
-
-
... More
Providing and fixing Indian teak wood planking 20mm - 50 mm thick for flooring plained on both sides, tongued and grooved including scaffolding, if necessary, and one coat of primer etc. complete
170
-
-
... More
Supply Providing and Fixing of wooden logs of 150mm to 300mm dia 600kg/cum Teak / pine Wood log Round with carvings as per architectural drawings and direction of Engineer-in-Charge
231.83
-
-
... More
Supply providing and filling geo polymer bags MACCAFERRI made or equivalant with available earth and gravels for the stablization of bund works complete as per the drawings and the direcions of engineer in charge.
2700
-
-
... More
Design, Supply, Fabrication and Installation of Membrane Panels. Fabric Makes- Serge Ferrari/Verseidag or Equivalent. Membrane shall be High Tenacity Polyester 1100 Dtex. multifilament Polyester with minimum Weight of 460 g/m2. The Fabric should have 0% openness -porosity for Maximum Light Visibility with minimum Tensile Strength (Warp/Weft) - 3000/ 3000 N/5cm, minimum Tear Strength (Warp/ Weft)-700/700 N/5 cm. Fabric Flame Retardancy Rating to be Euro Class - Bs2, do, Micro Organism Resistance and Warranty of 10 years. The design complies with the requirements of BS and, EU Standards. The tensioned membrane structure shall include engineering design of structural members and accessory parts. Membrane system shall include PVC/ PVDF coated Membrane Fabric, Wire Ropes and Cables, Shackles, Rigging Screws, Clamps and tensioning hardware as per specification, drawings and engineers approval. Vendor to provide OEM certificate for authorization.
200
-
-
... More
Supply Providing and fixing corten steel sheets in place complete as per the drawings and the directions of engineer in charge
1717.5
-
-
... More
Supply Providing & Installation of Frp Sheets of required texture and shape as per the drawings including all the necessary tools, clamps, accessiories etc complete work per design & drawing given by architect & directtions of engineer in charge
400
-
-
... More
Supplying & laying of drainage composite for use behind walls, between two different fills, alongside drains of road, below concrete lining of canals etc. having thermobonding a draining core - HDPE geonet comprises of two sets of parallel overlayed ribs integrally connected to have a rhomboidal shape with a polyethylene film and a nonwoven geotextile having mass per unit area 130 gsm and tensile strength of 8.0 kN/m that will be working as separation or protecting layer, geocomposite having in plane flow capacity of 0.7 L / (m.s) at hydraulic gradient of 1.0 & 20 kPa pressure and tensile strength of 13.5 kN/m , with mass per unit area of 830 gsm, at easily accessible location including top and bottom, with all leads and lifts, manpower and machinery, materials, labour etc. complete and as directed by Engineer - In - Charge.
12000
-
-
... More
Supply Providing and Fixing of Bamboo poles (tulda) in place of thickness 2.5 to 3.5 inches and 18to 20 ft long as per the architectural drawings and the directions of Engineer in Charge
3000
-
-
... More
Supply Providing and Fixing Railway Sleepers (wooden / psc concrete made) in place as per the drawings and the directions of engineer in charge
100
-
-
... More
Carving designs and textures on wooden logs as per the architectural drwaings and the directions of engineer in charge
20
-
-
... More
Supply providing and fixing in place Jute Rope 30mm dia 2ply complete as per the drawings and the directions of engineer in charge
3780
-
-
... More
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. bPL-RAckets, 40 mm flush bend, overflow arPL-RAngement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and bPL-RAckets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
4
-
-
... More
Providing and fixing of vitreous China Sanitary fixtures and CP fitting and other accessories for Handicapped toilet . Each Matrix Set shall comprised (Wash Basin 65 x 35 with one pair mounting bPL-RAckets, EWC & Cistern complete with fittings & seat cover, one no hinged PL-RAil 76 cm and five no's of gPL-RAb PL-RAils 60 cm). complete all respect. Make : Hindware Cat no. 70002 (Matrix Set-1) or equivalent make.
2
-
-
... More
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:.White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
5
-
-
... More
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge
6
-
-
... More
Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore
6
-
-
... More
Providing and fixing toilet paper holder :C.P. brass
5
-
-
... More
Providing and fixing of C.P. brass twin coat hook with PVC rawl plug & C.P. brass screw complete as required. Make : Jaquar : ACN-1161N or equivalent make.
6
-
-
... More
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 or equivalent make.
15 mm nominal bore
11
-
-
... More
Providing and fixing uplasticised PVC connection pipe with brass unions ; 15 mm nominal bore; 45 cm length
9
-
-
... More
Providing & fixing of CP brass Soap Dispenser with Glass Bottle of approved design and make. Make :Jaquar -Model No. ACN-1135N or equivalent make.
5
-
-
... More
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete
11
-
-
... More
Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.
3
-
-
... More
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
7
-
-
... More
Supply of solid state, no touch operating, fully hygienic hand drier of approved shade with single blower, with time delay, summer & winter control, music while drying, volume ON/OFF controls complete as required. Make : Euronics-Model No. EH 05 or equivalent make.
4
-
-
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes
18
-
-
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes
10
-
-
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes
5
-
-
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls etc. 32 mm nominal outer dia Pipes
10
-
-
... More
Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two
or more coats of synthetic enamel paint of required shade complete as required :
40 mm dia nominal bore
35
-
-
... More
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
32mm nominal bore
3
-
-
... More
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40mm nominal bore
8
-
-
... More
Providing and fixing in position of approved quality high pressure rated Gun Metal Float Valve with copper ball float and brass rods of required length suitable for test pressure of not less than 15 Kg/sqcm of the following sizes:
40mm nominal bore
3
-
-
... More
Providing & fixing Auto Air vent for cold water supply risers, suitable for pressure not less than 15 Kg/Sq.cm.
15 mm dia
2
-
-
... More
Providing, jointing, testing and fixing UPVC Soil, Waste & Vent system conforming to IS : 13592 (Type-B) and UPVC fittings (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offset and other specials. Jointing shall be done with push fit EPDM ring jointing technique in general. Solvent cement joints may be provided for fittings and specials which are not manufactured with push fit rubber joints. Fixing at wall/ceiling level supported by galvanized steel clamps & hangers etc. Making proper connection and also pipes may be laid / fixed in sunken floors, under slung from ceiling. The pipes laid in sunken floor shall be encased with not less than 75 mm thick cement concrete (1:2:4) all around. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. (All major MS structure to hold the stack is included in this item).
110 OD Type B
40
-
-
... More
Providing, jointing, testing and fixing UPVC Rain water system conforming to IS : 13592 (Type -A) and UPVC fittings (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offset and other specials. Jointing shall be done with push fit EPDM ring jointing technique in general. Solvent cement joints may be provided for fittings and specials which are not manufactured with push fit rubber joints. Fixing at wall/ceiling level supported by galvanized steel clamps & hangers etc. Making proper connection and also pipes may be laid / fixed in sunken floors, under slung from ceiling. The pipes laid in sunken floor shall be encased with not less than 75 mm thick cement concrete (1:2:4) all around. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. (All major MS structure to hold the stack is included in this item).
110 mm dia Type A
15
-
-
... More
Providing, fixing, jointing and testing UPVC soil, waste, vent pipework comprising UPVC pipe conforming to IS :4985-1983 of class 3 (6kg/cm2) as specified below and fittings (moulded as well as fabricated) like elbows, bends, reducers, threaded tail pieces, caps, suitable elbow with suitable extension piece for drain point and other specials jointing with cement solvent, chasing, cutting and making good the walls & floors pipes laid in floors shall be encased with 40 mm thick concrete all around, complete in all respects including testing of complete installation.(All major MS structure to hold the stack with fixing including anchor fasteners, sand, cement etc is included in this item) 40 mm od 6 kg/cm2 (Class III )
7
-
-
... More
Providing, fixing, jointing and testing UPVC soil, waste, vent pipework comprising UPVC pipe conforming to IS :4985-1983 of class 3 (6kg/cm2) as specified below and fittings (moulded as well as fabricated) like elbows, bends, reducers, threaded tail pieces, caps, suitable elbow with suitable extension piece for drain point and other specials jointing with cement solvent, chasing, cutting and making good the walls & floors pipes laid in floors shall be encased with 40 mm thick concrete all around, complete in all respects including testing of complete installation.(All major MS structure to hold the stack with fixing including anchor fasteners, sand, cement etc is included in this item) 63 mm od 6 kg/cm2 (Class III )
7
-
-
... More
Providing, fixing, jointing and testing UPVC soil, waste, vent pipework comprising UPVC pipe conforming to IS :4985-1983 of class 3 (6kg/cm2) as specified below and fittings (moulded as well as fabricated) like elbows, bends, reducers, threaded tail pieces, caps, suitable elbow with suitable extension piece for drain point and other specials jointing with cement solvent, chasing, cutting and making good the walls & floors pipes laid in floors shall be encased with 40 mm thick concrete all around, complete in all respects including testing of complete installation.(All major MS structure to hold the stack with fixing including anchor fasteners, sand, cement etc is included in this item) 110 mm of 6 kg/cm2 (Class III )
5
-
-
... More
Providing and fixing UPVC/SWR trap (P trap) of self cleaning design as per IS:13592 : 1992 complete including cost of cutting and making good the cutouts in walls and floors etc.including cutting and making good the walls and floors wherever required complete. 110 mm inlet and 110 mm outlet
8
-
-
... More
Providing and fixing floor drain made out of 110x63 mm OD uPVC elbow connected to uPVC pipe complete as per direction of Project Manager.
3
-
-
... More
Providing and fixing Inlet Fitting for Urinal trap, formed out of 110 mm PVC pipe with multiple side inlets formed with saddle pieces, suitable for 40, 50 and 63 mm dia side connections as per standard detail and support through galvanized steel support from slab or set in cement concrete mix 1:2:4 including cutting and making good the walls and floors wherever required.
8
-
-
... More
Providing and fixing Heavy Class SS grating of approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and FT, UT & FD.: Size 100 mm X 100 mm
11
-
-
... More
Providing and fixing P.V.C. WC connector (straight or bend type) with rubber lip ring. Including 110 mm dia PVC pipe / bend of required length and proper connection with M seal to C.I. pipe complete as required.
6
-
-
... More
Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, ounding the edges and making and finishing the outlet complete.: 450 x 450 mm
3
-
-
... More
Excavating trenches of required width for pipes, cables, etc. including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :
Ordinary rock :Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.
5
-
-
... More
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:
180x150 mm size P type :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
3
-
-
... More
Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 0.91 m deep with SFRC cover and frame (heavy duty, HD20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
1
-
-
... More
Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5
2
-
-
... More
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.
6
-
-
... More
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
1
-
-
... More
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
10
-
-
... More
Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :
19.27.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
14
-
-
... More
Providing & fixing in position precast SFRC manhole cover and frame of required shape and approved quality. H D -20
Square shape 450mm internal dimensions
30
-
-
... More
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150mm dia RCC pipe (For Hume Pipe)
214
-
-
... More
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia RCC pipe
374
-
-
... More
Supply Providing and Laying in place of 4 wheeler rubber tyers (Recycled ) complete as per the drawings and the directions of engieer in charge (The working condition of tyre shall be greater than 60%).
500
-
-
... More
Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:
1. Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.
2. IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. 3. IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.
4. IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).
326
-
-
... More
Providing & laying in position Prestressing steel strands (low relaxation) on hollow core bed by using mechanical pulling arrangement like Rabbit/ Bed master including all accessories for Stressing & destressing operations as per approved make conforming to IS1343 & grade FY-1860 etc, complete as per drawings and direction of Engineer -in-charge. 12.7mm dia
567.2
-
-
... More
Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.
1600
-
-
... More
Supply providing and fixing of cane sticks 10ft to 11 ft long in place as per the drawings and the directions of engineer in charge
500
-
-
... More
Supply providing and fixing in place nylon nets 3mm thick with mesh size 2inch square shave 100% UV established net complete work as per the drawings and the directions of engineer in charge.
1000
-
-
... More
Supply providing and fixing of rain water harvesting pits inclucing plumbing mechanical and electrical accessories and equipments of 20000ltrs capacity Zincalume tanks complete work as per the drawings and techincal specifications in test reports of the materials used as per directions of engineer in charge
40000
-
-
... More
Suplly providing and fixing of nylon rope 16mm dia in place as per the architectural drawings and the directions of engineer in charge
294
-
-
... More
Suppply providing and fixing of 8ft poly ethelene / nylon jumping trampoline for park areas with weightcarrying capacity upto 120kg as per the drawings and the directions of engineer in charge Note : work inc. cost of p/l, ew etc
5
-
-
... More
Supply providing and fixing of zipline setup made of SS tripple wire with load carring carrying capacity upto 500kg including the cost of structural works, safety measures breaks etc complete as per the drawings and the directions of engineer in charge
1
-
-
... More
Supply providing and installing Gyser nozzle (42 nos) and coulmn jet nozzel (20 nos) made of brass with submersible led light, electrical and plumbing work with installation of controlls boards, transformer 220/12V DC , 7.5HP PUMP with 3 phase discharge, complete work as per the directions of engineer in charge
1
-
-
... More
Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of
pile cap) : 300mm Dia Piles
200
-
-
... More
Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil
125
-
-
... More
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
1253
-
-
... More
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
16382.55
-
-
... More
Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete
62.5
-
-
... More
Fabrication & Manufacturing of Prestressed Hollow Core slab (Hollow area 25 to 30%) of different thickness & modular width 1200 mm in Controlled Factory Environment with approved methodology confirming to IS 10297:1982 by using long line casting method having arrangement of proper steel bed. Concreting should be done by batch mixing plant capable of producing zero slump concrete, transported through automatic shuttels of standard make & layed on bed with the help of extruder/Slipformer, finishing, curing and also provision of steam curing. Cutting, making necessary cutout/holes of required sizes for services in slab element after achieving required strength, yard handling & stacking all complete as per approved shop drawings & design mix as per the direction of the Engineer-in-charge. (Cost of strands should be paid separately). Note: Excess/less cement over the specified cement content used as per design mix is payable/recoverable separately) 26.73.1 Concrete Grade-M-40 (cement content 400 kg ) 26.73.1.4 200 mm thick hollow core slab
360
-
-
... More
Fabrication and manufacturing of solid precast concrete element with provisions of shear keys, connecting loops, dowel tubes and proper lifting accessories for walls, beams, slabs, stairs, column etc, of various thickness, shape and size of different concrete grades manufactured in controlled factory environment with approved methodology including moulds (Pallet system, Tilts form, table moulds, battery moulds, vertical moulds, beam moulds, column moulds, staircase moulds, Facade mould, etc.), mixing, transporting and placing of concrete, vibrating, curing, finishing, making necessary cutout/holes of required sizes for services, yard handling & stacking all complete as per IS 11447:1985 and as per approved shop drawings and design mix as per the direction of Engineer-in-Charge (Cost of reinforcement, Mechanical, Electrical and Plumbing inserts will be paid separately). 26.74.1
102.284
-
-
... More
Erection & Installation of Precast/Prestressed Concrete elements in correct & final position with proper line level and plumb at site making all arrangements (i.e cranes, push-pull jacks & all another T & P for lifting Placing & Alignment of elements, within erection tolerance as per IS 15916 as per approved shop drawings and all complete as per the direction of Engineer-in-Charge but excluding the cost of sim pads, non shrink grout and steel works i.e hangers. All work up to fifth floor.. Prestressed hollow core Slab up to 200 mm thickness
456
-
-
... More
Erection & Installation of Precast/Prestressed Concrete elements in correct & final position with proper line level and plumb at site making all arrangements (i.e cranes, push-pull jacks & all another T & P for lifting Placing & Alignment of elements, within erection tolerance as per IS 15916 as per approved shop drawings and all complete as per the direction of Engineer-in-Charge but excluding the cost of sim pads, non shrink grout and steel works i.e hangers. All work up to fifth floor. Solid concrete wall elements
102.284
-
-
... More
Supply and fixing factory made solid 25mm thick WPC panel (Wood Polymer Composite) of approved design as per the dimensions provided. WPC is composed of rice and wheat husk with thermo plastic single extruded, which should be termite proof, water proof, fire retardant ( Grade A) and Screwable having 1400 N screw holding capacity on the face and 1100N on edge, of approved make with UV stabilizers, which makes it 100% exterior grade. Material to be of density 550 kgs/cum. With GRIHA Council certification. The WPC panel shall be fixed on metal frame work (metal frame work shall be paid separately under relavant item head) with aluminium clamps/studs/rivets/bolts of suitable size as per manufacturer's specification. The contractor shall get the sample approved from competent authority prior to start of execution. Rate are inclusive of all labour, tool & plant,machineries, work at any height and complete in all respects and as per direction of Engineer-in-charge.
456
-
-
... More
Supply Providing and Fixing of Bamboo poles (tulda) in place of thickness 2.5 to 3.5 inches and 18to 20 ft long as per the architectural drawings and the directions of Engineer in Charge
180
-
-
... More
Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
24
-
-
... More
Supplying and laying 6 SWG G.I. wire at 0.50 meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
6500
-
-
... More
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as equired. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
150
-
-
... More
Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15mm dia G.I.pipe from earth electrode including connection with G.I thimble excavation and re-filling as required.
200
-
-
... More
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35 sq. mm
910
-
-
... More
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Above 35 sq. mm and upto 95 sq. mm
100
-
-
... More
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35 sq. mm
5500
-
-
... More
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 35 sq. mm and upto 95 sq. mm
650
-
-
... More
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.:
Upto 35 sq. mm (clamped with 1mm thick saddle)
1000
-
-
... More
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.: Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)
100
-
-
... More
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required: 63 mm dia (OD-63 mm & ID-51 mm nominal)
4500
-
-
... More
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required: 90 mm dia (OD-90 mm & ID-76 mm nominal) meter
3500
-
-
... More
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required: 120 mm dia (OD-120 mm & ID-103 mm nominal) meter
1500
-
-
... More
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with
chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm1461 nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :
With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
50
-
-
... More
Supplying and making end termination of 1.1 KV grade copper/aluminium multicore cables of the following sizes. The work includes sizing the core leads, removing insulation, fixing suitable crimping type aluminium lugs/thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals: 3.5C70sq.mm. AL armoured
6
-
-
... More
Supplying and making end termination of 1.1 KV grade copper/aluminium multicore cables of the following sizes. The work includes sizing the core leads, removing insulation, fixing suitable crimping type aluminium lugs/thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals: 4C35sq.mm. AL armoured
8
-
-
... More
Supplying and making end termination of 1.1 KV grade copper/aluminium multicore cables of the following sizes. The work includes sizing the core leads, removing insulation, fixing suitable crimping type aluminium lugs/thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals: 4C16sq.mm. AL armoured
75
-
-
... More
Supplying and making end termination of 1.1 KV grade copper/aluminium multicore cables of the following sizes. The work includes sizing the core leads, removing insulation, fixing suitable crimping type aluminium lugs/thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals: 2C6sq.mm. cu armoured
150
-
-
... More
Supplying and making end termination of 1.1 KV grade copper/aluminium multicore cables of the following sizes. The work includes sizing the core leads, removing insulation, fixing suitable crimping type aluminium lugs/thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals: 2C4sq.mm. cu armoured
250
-
-
... More
Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.: 3 x 2.5 sq. mm
1200
-
-
... More
Supplying of following types and sizes of 1.1 KV grade XLPE insulated copper / aluminium conductor armoured cable conforming to IS: 7098:
3.5CX70sq.mm. AL armoured
850
-
-
... More
Supplying of following types and sizes of 1.1 KV grade XLPE insulated copper / aluminium conductor armoured cable conforming to IS: 7098:4CX35sq.mm. AL armoured
650
-
-
... More
Supplying of following types and sizes of 1.1 KV grade XLPE insulated copper / aluminium conductor armoured cable conforming to IS: 7098: 4CX16sq.mm. AL armoured
1560
-
-
... More
Supplying of following types and sizes of 1.1 KV grade XLPE insulated copper / aluminium conductor armoured cable conforming to IS: 7098: 2CX6.0sq.mm. cu armoured
2500
-
-
... More
Supplying of following types and sizes of 1.1 KV grade XLPE insulated copper / aluminium conductor armoured cable conforming to IS: 7098: 2CX4.0sq.mm. cu armoured
1850
-
-
... More
Fabrication, Supplying Installation testing and commissioning of outdoor type cubical Feeder Pillar of (a) 1500mm W X 1500mm H X 400mm deep made out of M.S. Sheet 2mm thick (14 SWG) duly compartmentalized having two sections of 4 strips bus bar, bus bar-A of 160 Amp and Auxiliary bus bar-B of 100 Amp capacity, double door with locking arrangement for protection from rain, dust, duly fixed on M.S. angle iron frame work of size 50 mm x 50 mm x 5 mm 90 cm long legs out of which 45 cm duly grouted in cement concrete 1:2:4 (1 cement : 2 sand : 4 stone, aggregate 20 mm) and having following accessories mounted inside the cubical panel i/c connection, inter connection with aluminium thimbles, earthing with two nos. earth studs duly painted with one coat of red oxide & two coats of superior quality enamel paint complete etc. as required;
Supplying and fixing of following accessories in the existing cubical panel board / feeder pillar including connection testing etc. as required;
INCOMER: 1 No. 125 Amp. 415 Volts 4P MCCB of 25 KA (Ics = Icu = 100%);
METERING: 1 Set of Digital Voltmeter (0-500 V) 96 sq.mm. flush type with selector switch
1 Set of Digital Ammeter (0-125 A ) 96 sq.mm. flush type with selector switch & 125/5 Amp ratio CTs;
1 Set of 3 Nos. LED phase indication lamps (RYB) with 2 Amp. SP MCB;
BUSBAR;
Compartmentalized having two sections of 4 strips bus bar, bus bar-A of 160 Amp and Auxiliary bus bar-B of 100 Amp capacity;
OUTGOINGS (BUS BAR - A);
1 No. 63 Amps 415 Volts TP MCCB of 16 KA (Ics = Icu = 100%);
12 Nos. 40 Amps DP MCB; 1 No. 70 Amp. TP Power contactor (ML-4 ); 1 No. Astro Timer, D-21; OUTGOINGS (AUXILARY BUS BAR - B);
6 Nos. 20 Amps. TP MCB; 4 Nos. 32 Amps. DP MCB; OTHER ACCESSORIES
Provision for space for Inter face unit (SCADA Unit);
Hooter with Micro Switch and necessary Circuitry;
1 No. Danger notice plate;
Auto/Manual By Pass arrangement;
FP as described above and as per the drawings.
3
-
-
... More
Supplying Installation testing and commissioning of Specially designed spot light with glare cut visor 230-240Vac CRI >80 MacAdam step 3Input power : 40W-45W Dimension Ø166 x 153 x 423mm, Light Distribution Symmetrical along with inbuilt Electronic driver , IP rating must be IP65 or higher, Made out of Extruded aluminium bottom ribbed pipe (grade 6063 with test certificate) Ø166 x 3mm thickness & Die cast aluminium housing (grade ADC12 with test certificate). SS fasteners. Die-cast aluminium mounting plate Ø100.5 x 4mm thick with 2 elongated holes 15 x 10 to suit M8 bolts at PCD 55 with pure polyester powder coating. This mounting plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foudation. Hot dip galvanised foundation bolt. Mechanical resistance IK07. Pure polyester powder coated process : Acid treatment & pure polyester powder coating. Optical grade clear polycarbonate lens. Lamp fixed position. Should have minimum luminous flux of 90-100 lumens/Watt. This luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >85%, power factor >0.9, THD <10%, Surge protection 4KV. Manufacturer must have inhouse shot blasting machine and NABL certified lab equipped with photo goniometer, IP, IK test facilities Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN, the fixtures proposed must have passed LM 79 & LM- 80, latest Reports will be submitted before the supply of material CE & BIS Certified.
40
-
-
... More
Supplying Installation testing and commissioning of Static White 3000K surface mounted compact spot light designed to provide directional light. Beam angle 15° / 25° / 40°. Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive A2 stainless steel fasteners. Clear toughened glass of 4mm thickness. Hybrid optics with lens & mirror finish pure aluminium reflector combination for higher efficiency, lower optical losses with optimum glare suppression.Power consumption should be between 6W to 12W at steady state full intensity luminaire should have minimum luminous flux of 1054 Lm. Color rendering index CRI ≥ 80 and power factor of complete luminaire ≥ 0.90, at white colour. Swivel range of 0° - 90°. Single cable entrance M10 cable gland. Protection class IP65/66. Mechanical resistance IK06. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 3000K / 4000K, Colour rendering index (CRI)>80.
SDCM-3 MacAdam. LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Luminair 113 x 84 x 117mm.Adequate heat sink with proper thermal management shall be provided. Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%. THD should be less than 10%.Manufacturer must have inhouse shot blasting machine and NABL certified lab equipped with photo goniometer, IP, IK test facilities Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED
/NICHIA/CITIZEN, the fixtures proposed must have passed LM 79 & LM-80, latest Reports will be submitted before the supply of material CE & BIS Certified.y of material .
40
-
-
... More
Supplying Installation testing and commissioning of Recessed Underwater Input power : 30W LED recess mounted swimming pool luminaire for spot light. Beam angle 20°. Luminaire complete housing made of marine grade 316 stainless steel. ABS plastic installation housing for preparing the recess opening in wall. Step tempered glass of 10mm thickness. Hard wired for single colour 2 x 1.0mm2 of 3 metres water resistant cable. Protection class IP68. Mechanical resistance IK08. Available colour temperature 3000K, Colour rendering index (CRI)>80. K-Lite LED module with expected service life of at least 54,000 operating hours. Low Voltage non integral power supply at 12Vdc assures safety. Recommended installation depth upto 1meter below the water surface. Luminaire dimension : 205mm diameter x 81mm height. Manufacturer must have inhouse shot blasting machine and NABL certified lab equipped with photo goniometer, IP, IK test facilities Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN, the fixtures proposed must have passed LM 79 & LM-80, latest Reports will be submitted post the issuance of LOA to the successful bidder and before the supply of material CE & BIS Certified. Model: KL-2814
5
-
-
... More
Supplying Installation testing and commissioning of IP rating IP67 flex Input power : 9.6W, 2700K, 3000K, 4000K 24Vdc CRI >80 MacAdam step 3 Dimension1000 x 21 x 12.mm Beam angle : 10° x 45° Electronic driver ON/OFF (External driver), Silicone - Top Bend Mounting : Aluminium Channel, SS Clamp, SS flexible channel, Polyurethane Encapsulation diffuser This luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire >30,000 hours at 40°C. Operating ambient temperature range is from - 15°C to +50°C. Driver efficiency >85%, Surge protection 3KV. Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN Manufacturer must have inhouse NABL certified lab equipped with photo
goniometer, IP, IK test facilities CE and BIS.
150
-
-
... More
Supplying Installation testing and commissioning of 12W round decorative leser cut designer bollard LED 3000K, 4000K, 6500K 230-240Vac CRI >80 MacAdam step-3 Height 910mm Light Distribution Symmetrical, Electronic driver ON/OFF LUMINAIRE TYPE Bollard. IP rating IP66, Extruded square aluminium tube (grade 6063 with test certificate) Ø166 x 3mm thickness. Should have Bespoke laser cutting design options. SS fasteners. Must be equipped with Pre treated epdm black gaskets. Should have Die-cast aluminium mounting plate Sq.150 x 4mm thick with 3 elongated holes 20 x 12 to suit M10 bolts at PCD 90 with pure polyester powder coating. This mounting plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foudation. Hot dip galvanised foundation bolt. Mechanical resistance IK06. It should be Pure polyester powder coated process : Acid treatment & pure polyester powder coating. Optical grade clear toughened glass diffuser of 4mm thickness with controlled downward light emission. Lamp fixed position.This luminaire should contains built-in IP 66 LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >85%, power factor >0.9, THD <10%, Surge protection 2.5KV.Manufacturer must have inhouse shot blasting machine and NABL certified lab equipped with photo goniometer, IP, IK test facilities Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN, the fixtures proposed must have passed LM 79 & LM-80, latest Reports will be submitted before the supply of material CE & BIS Certified.y of material .
15
-
-
... More
Supplying Installation testing and commissioning of 50W LED round decorative leser cut designer column LED 3000K, 4000K, 6500K 230-240Vac CRI >80 MacAdam step-3 Height 4000mm Light Distribution Symmetrical, Electronic driver ON/OFF LUMINAIRE TYPE Bollard. IP rating IP65, Extruded square aluminium tube (grade 6063 with test certificate) Ø166 x 3mm thickness. Should have Bespoke laser cutting design options with 1400mm length. SS fasteners. Must be equipped with Pre treated epdm black gaskets. Should have Die-cast aluminium mounting plate Ø300X 16mm thick 4 Elongated holes 48 x 24 to suit M20 bolts at CC 215 with pure polyester powder coating. This mounting plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foudation. Hot dip galvanised foundation bolt. Mechanical resistance IK06. It should be Pure polyester powder coated process : Acid treatment & pure polyester powder coating. Optical grade clear toughened glass diffuser of 4mm thickness with controlled downward light emission. Lamp fixed position.This luminaire should contains built-in IP 65 LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >85%, power factor >0.9, THD <10%, Surge protection 6KV.Manufacturer must have inhouse shot blasting machine and NABL certified lab equipped with photo goniometer, IP, IK test facilities Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN, the fixtures proposed must have passed LM 79 & LM-80, latest Reports will be submitted before the supply of material CE & BIS Certified.
15
-
-
... More
Supplying Installation testing and commissioning of 36-40W LED linear wall washer with antiglare visor, should be available in LED colors 3000K, 4000K, 6000K 24Vdc CRI >80 MacAdam step 3, should have maximum Dimension of 1000 x 35 x 78mm and with beam angle of 30° /15°X60°, IP rating IP65, Extruded aluminium alloy housing (grade 6063). Toughened clear glass diffuser. SS fasteners. Aluminium mounting bracket for surface mounting on ground. Toughened Clear glass diffuser and optical to reduce glare controlled.
This luminaire contains built-in LED modules. LED modules are
engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >85%, power factor >0.90, Surge protection 3KV. Manufacturer must have inhouse shot blasting machine and NABL certified lab equipped with photo goniometer, IP, IK test facilities Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM
/ SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN, the fixtures proposed must have passed LM 79 & LM-80, latest Reports will be submitted before the supply of material CE & BIS Certified.y of material .
20
-
-
... More
Supplying Installation testing and commissioning of Input power : 2 x 60W LED high efficiency flood light luminaire designed to provide uniform illumination in open spaces. Beam angle 12° / 25° / 40° / 60°. Extruded aluminium side frame, IP67 LED Module with excellent thermal management heat sink with vertical fin design for longer life of the LEDs & polycarbonate optical lens. Mounting bracket made of CRCA sheet (3mm thickness). Luminaire supplied with fast IP67 connectors. All external screws are made of stainless steel. Mechanical resistance IK08. Pure polyester powder coated RAL 9004 Signal black, RAL9007 Grey aluminium, RAL 7016 Anthracite grey, Graphite grey. Available colour temperature 3000K / 4000K / 5700K / Amber(25°). Colour rendering index (CRI)>70. K-Lite LED module with expected service life of at least 84,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >90%, Power factor >0.98, THD< 6.5%, Surge protection 4KV. Luminaire dimension : 342mm length x 135mm width x 245mm height.Manufacturer must have inhouse shot blasting machine and NABL certified lab equipped with photo goniometer, IP, IK test facilities Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN, the fixtures proposed must have passed LM 79 & LM-80, latest Reports will be submitted before the supply of material CE & BIS Certified.y of material .
15
-
-
... More
Supplying Installation testing and commissioning of Input power : 3W LED spike mounted compact spot light designed to provide directional light. Beam angle 8° / 12° / 24° / 40° / 60° / 40°x11°. Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive stainless steel fasteners. Clear toughened glass of 4mm thickness. Surface mounting spike made of polypropylene black. Hybrid optical lens for higher efficiency, lower optical losses with optimum glare suppression. Swivel range of 0° - 90°. Single cable entrance M10 cable gland. Protection class IP66. Mechanical resistance IK06. Pure polyester powder coated RAL 9004 Signal black, RAL9007 Grey aluminium, RAL 7016 Anthracite grey, Graphite grey. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. K-Lite LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Luminaire dimension : 93mm length x 90mm width x 320mm height. Manufacturer must have inhouse shot blasting machine and NABL certified lab equipped with photo goniometer, IP, IK test facilities Make of LEDs -LEDs of CREE /LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN, the fixtures proposed must have passed LM 79 & LM-80, latest Reports will be submitted before the supply of material CE & BIS Certified.y of material .
30
-
-
... More
Supplying Installation testing and commissioning of IP-65 recessed down light LED 3000K, 4000K, 6500K 240Vac CRI >80 MacAdam step 3 Input power : 30W Beam angle : 60°Die-cast aluminium housing with aluminium heat sink for better thermal management. Aluminium reflector, polycarbonate optical cover. Mechanical resistance IK07. Must have Polycarbonate optical cover, This luminaire should contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >85%, Power Factor >0.9, THD <10%, Surge protection 2.5KV. Manufacturer must have inhouse shot blasting machine and NABL certified lab equipped with photo goniometer, IP, IK test facilities Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN, the fixtures proposed must have passed LM 79 & LM-80, latest Reports will be submitted before the supply of material CE & BIS Certified.y of material .
100
-
-
... More
Supplying Installation testing and commissioning of Cyrilla bollard Input power : 12W LED bollard luminaire designed for Symmetrical light distribution. Luminaire made of extruded aluminium supporting arm (grade 6063), pressure die cast aluminium top and bottom frame and non corrosive stainless steel fasteners. Bespoke laser cutting stainless steel leaf design. Protection class IP53. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 2700K / 3000K / 4000K / 6500K. Colour rendering index (CRI)>80. SDCM- 3 MacAdam.LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.9, THD <10%, Surge protection 2.5KV. Luminaire dimension : Sq.206 x 500mm. CE & BIS Certified.
Manufacturer must have inhouse shot blasting machine and NABL certified lab equipped with photo goniometer, IP, IK test facilities Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN, the fixtures proposed must have passed LM 79 & LM-80, latest Reports will be submitted before the supply of material CE & BIS Certified.y of material .
20
-
-
... More
SITC of exterior gobo projector shall be designed for dynamic architectural ligh ng applica ons, with a rugged and weatherproof construc on suitable for outdoor installa ons. It shall feature a high-performance op cal system that delivers a uniform, high-output light beam with a na ve beam angle of approximately 6°, and op onal spread lenses shall be available to widen the beam as required by the project. The fixture shall u lize high-efficiency RGBW LEDs to achieve rich, saturated colors and high-quality white tones, with the ability to generate a broad range of color temperatures. The housing shall be made of corrosion-resistant, die-cast aluminum with a protec ve coa ng to ensure durability in harsh environmental condi ons. The op cal assembly shall be protected by a tempered glass cover and sealed to provide an IP66-rated ingress protec on, safeguarding internal components from dust and water ingress. The unit shall be designed to operate in ambient temperatures ranging from -40°C to +50°C and shall include onboard thermal protec on to ensure longevity and reliability. The projector shall feature integrated power and control electronics and support DMX/RDM and DALI protocols for flexible and precise control. It should allow for individual or grouped control of mul ple fixtures, with a standalone mode also available for basic applica ons. The fixture shall support both horizontal and ver cal lt adjustment, with an aiming lock to secure posi oning a er installa on. Electrical connec on shall be facilitated via waterproof connectors, and the unit should operate on a wide input voltage range to suit diverse project requirements. The luminaire shall be capable of delivering a high lumen output, with adjustable se ngs to match the specific lighing needs of the applica on. Moun ng brackets and accessories shall be available to support surface or pole installa ons. All components shall comply with relevant interna onal standards for safety, EMC, and performance, and the fixture should be supplied pre-wired for ease of installa on on-site. Complete with all necessary accessories Approved Make- Mar n/ETC/Rosco
1
-
-
... More
SITC of moving head profile luminaire shall be a high-output automated ligh ng fixture suitable for professional stage, event, and architectural applica ons. It shall feature a powerful short-arc discharge lamp source, delivering a high-intensity output with excellent color rendering. The fixture shall be equipped with an advanced op cal system designed to produce a flat, even field with sharp image projec on across the en re beam. A motorized zoom system shall allow for a variable beam angle range to suit various applica ons, while an iris shall be included for beam size reduc on. The unit shall incorporate a full CMY color mixing system for seamless transi ons and color blending, in addi on to a color wheel with a selec on of fixed colors. It shall be equipped with two gobo wheels—one sta c and one rota ng—offering a variety of pa erns for image projec on. The rota ng gobos shall be indexable and interchangeable, and the fixture shall include addi onal effects such as a rota ng prism and an anima on wheel for dynamic visual outputs. A motorized focus system shall allow precise adjustment to maintain clarity at variable projec on distances. The luminaire shall feature high-speed, variable-speed strobe effects, along with a dimmer capable of smooth transi ons from 0 to 100%. The fixture should allow for precise pan and lt movements with high resolu on and fast posi oning. Control shall be via standard DMX512 protocol, and the unit shall be compa ble with remote management systems for monitoring and addressing. The fixture shall have user-selectable opera ng modes and configurable se ngs accessible via an onboard display and menu system. The housing shall be constructed of high-quality, flame-retardant materials and designed to opmize airflow for efficient cooling. The fixture shall be equipped with automated thermal management to prevent overhea ng and ensure reliable performance. It should support installa on in environments with a wide range of ambient temperatures, and all electrical components shall be compliant with relevant interna onal safety and EMC standards. The luminaire shall be supplied with appropriate moun ng hardware and should be suitable for rigging in touring, theatrical, and permanent installa ons. Complete with all necessary accessories Approved Make- Mar n/ETC/Rosco
1
-
-
... More
SITC of DMX system for above product
1
-
-
... More
SITC of CATENARY LIGHT
250
-
-
... More
SITC CUT LETTER SIGNAGE
1
-
-
... More
Providing and laying in position 1:2:4 reinforced cement concrete foundation of size 350 mm.(L) X 350 mm. wide and 1500 mm. deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of cold twisted bars of 12 mm. dia- 1060mm long (approx)- 8 Nos. and reinforcement ring of cold twisted bar of 8mm dia - 2800mm (approx) - 10nos. (with 150mm spacing) as required with and providing two nos. 90 mm. (O.D) DWC, HDPE Pipe for cable entry & exit as required. with positioning of foundation bolts including 4 Nos. 25mm dia X 800mm long GI foundation bolt (EN8 grade) with nuts, washer including 2 Nos. template of 4mm thick size 310mm x 310mm with 4 nos. 28mm dia holes, to match with PCD of Pole base plate as (for 4 mtrs)
95
-
-
... More
Supply, Installation, Testing and Comissioning of USB Full HD 1080p@30fps Web Camera, 1/3”, 2.07MP sensor, 60 Degree FOV, built in Mic, 360 degree manual rotation, privacy shutter, MJPEG compression format, Auto Focus, Auto white balance & other image processing algorithms, USB 2.0, BIS, CE,FCC, RoHS certified, [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]
6
-
-
... More
SITC of complete system Workstation for Client- Min Specs Intel Core i7-9700K, 16GB, Graphic card - 4 GB/Quadro P1000, 2x1G, Windows 10 Pro, 2x1TB @RAID1, KBD, Mouse
1
-
-
... More
Supply, installation, testing and commissioning of Network Video Recorder , Live view/Resolution 5MP/3MP/1080p/720p,Motion Detection Control Privacy Mask Control. USB interface-1 × USB 2.0 and 1 × USB 3.0,Security-HTTPS, SSL, Watermark, User Authentication, Miscellaneous-N+1 hot spare. Alarm in/out -4 / 1,Network interface-1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface, Security-HTTPS, SSL,Video/Audio output-VAG,HDMI and Audio. Watermark, User Authentication,Incoming bandwidth-100Mbps,Outgoing bandwidth-80Mbps,HDMI output,VGA Output,Protocol-IPv4, IPv6, TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP, SNMP, NFS, and iSCSI are supported.TCP, UDP and RTP for unicast, UPnPTM, ONVIF, PSIA,Support 100 IP Camera, 2 SATA interfaces for 4 HDDs Upto 6TB for each disk. Make-Tyco/Mobotix/Pelco
1
-
-
... More
Supply, installation, testing and commissioning of Network Video Recorder , Live view/Resolution 5MP/3MP/1080p/720p,Motion Detection Control Privacy Mask Control. USB interface-1 × USB 2.0 and 1 × USB 3.0,Security-HTTPS, SSL, Watermark, User Authentication, Miscellaneous-N+1 hot spare. Alarm in/out -4 / 1,Network interface-1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface, Security-HTTPS, SSL,Video/Audio output-VAG,HDMI and Audio. Watermark, User Authentication,Incoming bandwidth-100Mbps,Outgoing bandwidth-80Mbps,HDMI output,VGA Output,Protocol-IPv4, IPv6, TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP, SNMP, NFS, and iSCSI are supported.TCP, UDP and RTP for unicast, UPnPTM, ONVIF, PSIA,Support 100 IP Camera, 2 SATA interfaces for 4 HDDs 6 TB HDD (Seagate/WD)
1
-
-
... More
SITC of following sizes of 240Volt POE Switch ::
8 POE Switch external
1
-
-
... More
SITC of following sizes of 240Volt POE Switch ::
16 POE Switch control room
1
-
-
... More
Supply ,Receiving fixing of 42" display for monitoring purpose of the servilance with required mount details.Make : Samsung/LG/Lapcare
1
-
-
... More
Supply, installation, testing and commossioning of 4 pair Cat 6 LAN cable in existing GI Conduit Including ferruling (6 Digit)etc. complete as required.
500
-
-
... More
Supply & fixing of following sizes of GI conduit in surface / recess along with the accessories including cutting the wall & making good the same in case of recessed conduit as required. :
25 mm dia conduit.
500
-
-
... More
Supply & laying of Cat-6 Armoured Cable for out door camera
500
-
-
... More
Supply & fixing of Hansel Box
20
-
-
... More
Supply & fixing of 6 u rack Weatherprof
2
-
-
... More
SITC Armoured 6 Core Optical Fiber Cable Single mode for induvial junction connection at tower (Make-D-Link)
200
-
-
... More
Supply & fixing of Media Convertor Single Mode D-Link
1
-
-
... More
SITC of PATCH CORD LC-LC SM DUPLEX LENGTH- 3m [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]
1
-
-
... More
Splicing & commissioning work for fiber jointing work
4
-
-
... More
SUPPLY, INSTALLATION, TESTING & COMISSIONING OF HIGH-SPL FOREGROUND MUSIC SPEAKER WITH A 8" LF8 DRIVER OR BETTER AND EMB2S EXTENDED HIGH-FREQUENCY COMPRESSION DRIVER, BIAMPLIFIED 2WAY ARRAY LOUDSPEAKER SYSTEM; WITH INDIVIDUAL MODULE FREE FIELD FREQUENCY RANGE (-10DB) OF 80HZ - 18KHZ OR BETTER & PEAK POWER HANDLING OF >= 800W LF . THE LOUDSPEAKER MODULE SHALL HAVE A MAX. SPL (PEAK) OF MF/HF>= 121DB OR BETTER. IT SHOULD HAVE HORIZONTAL NEAR DISPERSION PATTERN OF 90º OR BETTER, VERTICAL DISPERSION OF THE ARRAY SHALL BE 60º OR BETTER. THE MODULES SHALL HAVE A WEATHER RATING OF IP55. including SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF OEM AU SHAPE MOUNTING ARRANGEMENT FOR SUSPENSION OR WALL MOUNTING OF THE MODULES OFFERED ABOVE.MAKES.
6
-
-
... More
SITC OF 8 CHANNEL CLASS D NETWORKABLE POWER AMPLIFIER WITH A MAX OUTPUT POWER OF 8X500W@8 OHMS, OR BRIDGED MODE OUTPUT POWER OF 4X 1000W @ 8/4 OHMS. 20HZ - 20 KHZ, SNR OF 102DB AND THD + N OF <0.4% WITH BUILT IN PROTECTION SUCH AS LIMITERS, TEMPERATURE, DC, SHORT CIRCUIT, PEAK CURRENT LIMITERS, TURN ON DELAY ETC. BUILT IN DSP FOR MATRIX ROUTING, SPEAKER EQUALIZATION, DELAYS, ARRAY EQS ETC. COMPLETE WITH ETHERNET PORT FOR NETWORK CONTROL, PROGRAMMING AND MONITORING. SHALL OFFER OPTIONAL NETWORK AUDIO CONNECTIVITY (DANTE OR COBRANET) THROUGH EXPANSION SLOT. .MAKES. JBL
1
-
-
... More
SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF 2 CONDUCTOR 12 AWG(168 X 34) OXYGEN-FREE BARE COPPER (HIGH CONDUCTIVITY) CABLE NEC TYPE CM AND CL3 TYPE FOR AUDIO ONLY WITH DC RESISTANCE: 1.60 Ω/1000FT. ,MUTUAL CAPACITANCE: 22.3PF/FT.,VOLTAGE RATING: 300V,MAXIMUM CURRENT: 17A@25˚C, AND CABLE ROLL PACKING -500 MTR. .MAKES. BELTEN
1
-
-
... More
SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF CAT6 UTP 23AWG TWISTED PAIR ARMORED CABLE, SUPPORTS GIGABIT ETHERNET (1000 BASET) STANDARD. OPERATES AT BANDWIDTH OF 250 MHZ. THIS CABLE WELL EXCEEDS THE REQUIREMENTS OF TIA/EIA-568-C.2.,CONDUCTOR RESISTANCE (DC): 93.5 OHM/1000 MTR @20°C MAX,IMPEDANCE: 100±15% OHM AND TEMPERATURE RATING: -20° TO + 60°C .ROLL PACKING:305 MTR.ENHANCED PERFORMANCE CABLE FOR TRANSMISSION OF HIGH SPEED DATA, DIGITAL AND ANALOGUE VOICE AND VIDEO (RGB) SIGNALS ON LANS. MAKES- D-LINK
1
-
-
... More
SITC OF WEATHERISED ENCLOSURE FOR AUDIO AMPLIFIER WITH FRONT DOOR, FRONT AND BACK ADJUSTABLE MOUNTING RAILS, 1 FAN MOUNTING PROVISION, TOP AND BOTTOM CABLE ENTRY PROVIDES OPTIMAL FLEXIBILITY FOR CABLE MANAGEMENT,EASY WALL MOUNT PROVISION, EASY INSTALLATION- STANDING / WALL MOUNTING OPTION COMPATIBLE WITH INTERNATIONAL STANDARDS AND ENCLOSURE DIMENSION'S ARE WXDXH (600 X 600 X 340 MM). MAKES- LIBERTY
1
-
-
... More
SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF CUSTOMISED DIGITAL ADVERTISING VERTICAL KIOSK, 50 INCH SCREEN(BOTH SIDE), 250 WATTS,P10/P14 RESOLUTION, IP-67, IK-10.
10
-
-
... More
SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF CUSTOMISED WALL SURFACE MOUNTED LED SCREEN WITH, 300 WATTS, P10/P-14 RESOLUTION, IP-67, IK-10. (DIMENSION- L1800MMXH150MM)
9
-
-
... More
SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF CUSTOMISED DIGITAL ADVERTISING ROUND KIOSK, 500 WATTS, P10/P14 RESOLUTION, IP-67, IK-10. (DIMENSION-D2000MMXH1000MM).
6
-
-
... More
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. :
Group C
50
-
-
... More
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
20
-
-
... More
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.: 2 X 4 sq. mm + 1 X 4 sq. mm earth wire
150
-
-
... More
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.: 2 X 10 sq. mm + 1 X 6 sq. mm earth wire
100
-
-
... More
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
20
-
-
... More
Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting, fans of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.
50
-
-
... More
Supplying and fixing following way , single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar , neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without MCB/RCCB/ isolator) :
12 way double door
1
-
-
... More
Supplying and fixing following way , single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar , neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without MCB/RCCB/ isolator) : 16 way double door
1
-
-
... More
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
28
-
-
... More
Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A
2
-
-
... More
FITTINGS: Supply and fixing of ceiling LED downlights of 15 watts of brand philips, havells or equivalent as per direction and approval of Engineer in charge.
50
-
-
... More
FITTINGS: Supply and fixing of ceiling LED downlights of 1200mm sweep ceiling fanof brand havells or equivalent as per direction and approval of Engineer in charge.
10
-
-
... More
Supply, installation and fixing of 50mm wide Glow LED light band, front facia/ ceiling 3mm thick Acrylic polycarbonate sheet inside LED strip light arrangement including all fittings and required accessories with Channel frame running all sides of wall and fixed with fastners on concrete wall, Silicon sealant on all joint and waterproof power supply with all fittings including cable & conduit provision etc complete as per drawing and specification. and as per direction of Engineer-in-charge.
2
-
-
... More
Providing and fixing LED driver AC 240 V to 12V DC, transformaer adapter for LED strip light module etc all complete as per direction of Engineer-in-charge
2
-
-
... More
Supply, installation and fixing of Display box of size 600 x 600 x 300mm at top of Kiosk, LOGO & KIOSK NAME on each side with Acrylic letter (100mm) with inside LED light including all fittings and required accesosries. Front facia and sides 3mm thk. Polycarbonate sheets and top with 3mm thick S.S sheet, Box frame 20 x 20mm S.S box section, and at each corner lower part having 50 x 50 x 5mm S.S plate with 12mm hole, Fixing on 50 x 50x 5mm S.S plate with 10mm bolt anchored to the base with fastners (4nos. fastners for each plate), Silicon sealant on all joint and waterproof power supply with all fittings including cable & conduit provision etc complete as per drawing and specification. and direction of Engineer-in-charge.
2
-
-
... More
Supply, installation and fixing of Backlit Advertisement pannel on wall of size 1650 x 950mm (avg.) , All body aluminium outdoor SDPE system with LED modules waterproof supply light top 5mm acrylic backlight with printing complete as per drawing and specification. and direction of Engineer-in-charge.
2
-
-
... More
Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water
(excluding cost of imported earth, sludge or manure).
21392.25
-
-
... More
Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).
1560
-
-
... More
Supplying and stacking sludge at site including royalty and carriage upto 5 km complete (sludge measured in stacks will be reduced by 8% for payment).
3874
-
-
... More
Rough dressing the trenched ground including breaking clods.
2400
-
-
... More
Fine dressing of the ground.
2400
-
-
... More
Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).
5434
-
-
... More
Mixing earth and sludge or manure in the required proportion specified or
directed by the Officer-in-charge
5434
-
-
... More
Providing & laying Selection no. 1 grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same and maintenance for 30 days or more till the grass establish properly, as per direction of the officer in charge
2400
-
-
... More
Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20%: one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)
1200
-
-
... More
Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :Holes 60 cm dia, and 60 cm deep
225
-
-
... More
Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :Holes 45 cm dia, and 45 cm deep.
190041
-
-
... More
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material’s as per direction of officer in charge (excluding cost of plant & water) : Tree plant
225
-
-
... More
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material’s as per direction of officer in charge (excluding cost of plant & water) : Shrub & Ground cover
190041
-
-
... More
Providing and stacking of Memecylon umbellatumin big poly bags of size 30 cm as per direction of the officer-in-charge.
5
-
-
... More
Providing and stacking of Bauhinia purpurea (Kachnar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge
15
-
-
... More
Providing and stacking of Gmelina arborea in big poly bags of size 30 cm as per direction of the officer-in-charge.
10
-
-
... More
Providing and stacking of Tectona grandis (Teak) of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.
15
-
-
... More
Providing and stacking of Shorea robusta in big poly bags of size 30 cm as per direction of the officer-in-charge.
10
-
-
... More
Aquilaria malaccensis in big poly bags of size 30 cm as per direction of the officer-in-charge.
10
-
-
... More
Providing and stacking of Alstonia scholaris of height 150-165 cm. in bag of size 25 cm as per direction of the officer-in-charge.
10
-
-
... More
Providing and stacking of Ailanthus excelsa in big poly bags of size 30 cm as per direction of the officer-in-charge.
10
-
-
... More
Providing and stacking of Terminalia catappa in big poly bags of size 30 cm as per direction of the officer-in-charge.
10
-
-
... More
Providing and stacking of Moringa oleifera in big poly bags of size 30 cm as per direction of the officer-in-charge.
15
-
-
... More
Providing and stacking of Bambusa balcooa in big poly bags of size 30 cm as per direction of the officer-in-charge.
10
-
-
... More
Providing and stacking of Dendrocalamus hamiltonii in big poly bags of size 30 cm as per direction of the officer-in-charge.
5
-
-
... More
Providing and stacking of Bambusa tulda in big poly bags of size 30 cm as per direction of the officer-in-charge.
15
-
-
... More
Providing and stacking of Dendrocalamus giganteus in big poly bags of size 30 cm as per direction of the officer-in-charge.
15
-
-
... More
Providing and stacking of Phyllanthus emblica (Amla) of height 150-165 cm. in Big HDPE Bag as per direction of the officer-in-charge.
15
-
-
... More
Providing and stacking of Tetrameles nudiflora in big poly bags of size 30 cm as per direction of the officer-in-charge.
2
-
-
... More
Providing and stacking of Shorea assamica in big poly bags of size 30 cm as per direction of the officer-in-charge.
3
-
-
... More
Providing and stacking of Ficus religiosa (Peepal) of height 150-165 cm. in big poly bags of size 30 cm as per direction of the officer-in-charge.
15
-
-
... More
Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.
10
-
-
... More
Providing and stacking of Terminalia arjuna of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.
15
-
-
... More
Providing and stacking of Polyalthia pendula (Ashok Pendula) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge
10
-
-
... More
Providing and stacking of Angiopteris assamica of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge
443
-
-
... More
Providing and displaying of Dieffenbachia Tropic-snow having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
1772
-
-
... More
Providing and displaying ofGlycosmis pentaphylla having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
98
-
-
... More
Providing and displaying of Asplenium nidus having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
1772
-
-
... More
Providing and displaying of Curcuma angustifolia having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
3544
-
-
... More
Providing and displaying of Drynaria quercifolia having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
886
-
-
... More
Providing and displaying of Colocasia spp. having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
886
-
-
... More
Providing and displaying of Calamus latifolius having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
35
-
-
... More
Providing and displaying of Alocasia spp. having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
443
-
-
... More
Providing and displaying of Sansevieria roxburghiana having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
222
-
-
... More
Providing and displaying of Barleria grandiflora having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
500
-
-
... More
Providing and displaying of Aerides odorata having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
1772
-
-
... More
Providing and displaying of Rhynchostylis retusa having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
2658
-
-
... More
Providing and displaying of Vanda coerulea having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
1772
-
-
... More
Providing and displaying of Adiantum caudatum having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
3544
-
-
... More
Providing and displaying ofBambusa cacharensis having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
89
-
-
... More
Providing and displaying of accharum spontaneum having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
304
-
-
... More
Providing and displaying of Arundinella bengalensis having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
304
-
-
... More
Providing and displaying of Phragmites karka having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
304
-
-
... More
Providing and displaying of Panicum paludosum having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
3648
-
-
... More
Providing and displaying of Miscanthus fuscus having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
304
-
-
... More
Providing and displaying of Cymbopogon flexuosus having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
1824
-
-
... More
Providing and displaying of Anisomeles indica having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
912
-
-
... More
Providing and displaying of Melocanna baccifera having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
36
-
-
... More
Providing and displaying of Bambusa nutans having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
36
-
-
... More
Providing and displaying of Nodding bamboo having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
36
-
-
... More
Providing and stacking of Phoenix sylvestris Roxb. (Wild date palm/khajur) of height 150-165 cm. in Big HDPE Bag as per direction of the officer-in-charge.
10
-
-
... More
Providing and stacking of Mesua ferrea of height 150-165 cm. in Big HDPE Bag as per direction of the officer-in-charge.
8
-
-
... More
Providing and stacking of Thysanolaena maxima of height 150-165 cm. in Big HDPE Bag as per direction of the officer-in-charge.
304
-
-
... More
Providing and stacking of Caesalpinia pulcherrima species of height 45-60 cm. in earthen pot of size 20 cm as per direction of the officer-in-charge.
182
-
-
... More
Providing and stacking of Bauhinia blakeana (Kachnar) of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
304
-
-
... More
Providing and stacking of Calotropis procera of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
182
-
-
... More
Providing and stacking of Argyreia argentea of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
182
-
-
... More
Providing and displaying of Croton golden (Broad Leaves) having ht. 60 cm to 75 cm with 3 to 4 branches, well developed, fresh and healthy leaves in 25 cm size of Earthen pot/Plastic pot. & as per direction of the officer-in-charge.
182
-
-
... More
Providing and stacking of Jasmine grandiflorum (chameli) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. .
182
-
-
... More
Providing and stacking of Lagerstroemia flosreginae of height 150-165 cm.in big poly bag of size 25 cm as per direction of the officer-in-charge.
18
-
-
... More
Providing and stacking of Ceratopteris thalictroides The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
1543
-
-
... More
Providing and stacking of Cyperus alternifolius The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
4529
-
-
... More
Providing and stacking of Vallisneria spiralis The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
7844
-
-
... More
Providing and stacking of Acorus calamus The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
3186
-
-
... More
Providing and stacking of Typha latifolia The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
3186
-
-
... More
Providing and stacking of Phragmites australis The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
3186
-
-
... More
Providing and stacking of Hydrocera triflora The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
4529
-
-
... More
Providing and stacking of Cephalotaxus fortunei The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
1590
-
-
... More
Providing and stacking of Nymphaea caerulea The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
6280
-
-
... More
Providing and stacking of Cyperus rotundus The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
1520
-
-
... More
Providing and stacking of Hygrophila polysperma The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
50900
-
-
... More
Providing and stacking of Bacopa monnieri The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
50500
-
-
... More
Providing and stacking of Sagittaria guyanensis The supply includes labour for handling, loading, unloading by manual means, and transportation to site.
All plants must be inspected and approved by the Officer-in-Charge prior to planting. The minimum height of plants shall range between 15 cm to 90 cm, as appropriate for the species and their growth habit.
12698
-
-
... More
Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge.
1200
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%