Gauhati University Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Gauhati University Tender
Civil And Construction
Building Construction
Eprocure
Opening Date30 Sep 2022
Closing Date20 Oct 2022
Tender Amount₹ 2,99,23,821
Costs
EMD
₹ 5,98,476Document Cost
₹ 6,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2022_GU_27246_1Bid Award Id
ViewTender No
T/22-23/128 dated 29.09.2022Tender Authority
Gauhati University ViewPurchaser Address
-Website
http://https://www.gauhati.ac.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m.
1146
-
-
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
144
-
-
ANTI-TERMITE TREATMENT
Supplying chemical emulsion in sealed containers including delivery as specified.
Chlorpyriphos / Lindane emulsifiable concentrate of 20%
267
-
-
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL
anti-termite treatment (excluding the cost of chemical emulsion) :
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:
With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
480
-
-
CONCRETE WORK
CEMENT CONCRETE (CAST IN SITU)
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20mm nominal size).
0.4
-
-
1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20mm nominal size).
51
-
-
1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)
44
-
-
DAMP-PROOF COURSE
Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)
64
-
-
Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.
64
-
-
MISCELLANEOUS
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20mm nominal size) over 75mm thick bed of dry brick ballast 40mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling, dressing & finishing the top smooth.
159
-
-
REINFORCED CEMENT CONCRETE
CAST IN SITU
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural
sources : 3 graded stone aggregate 20 mm nominal size de
rived from natural sources)
0.7
-
-
FORM WORK
Centering and shuttering including strutting, propping etc. and removal of form for:
Foundations, footings, bases of columns, etc. for mass concrete
222.8
-
-
Walls (any thickness) including attached pilasters, butteressess, plinth and string courses etc.
0.9
-
-
Suspended floors, roofs, landings, balconies and access
platform
630.5
-
-
Lintels, beams, plinth beams, girders, bressumers and cantilevers.
1276.4
-
-
Columns, pillars, piers, abutments, posts and struts.
1020
-
-
Stairs, (excluding landings) except spiral-staircases
57
-
-
Extra for shuttering in circular work (20% of respective centering and shuttering items)
204
-
-
Weather shade, Chajjas, corbels etc., including edges
150
-
-
STEEL REINFORCEMENT
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
31415
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
32875
-
-
DESIGN MIX CONCRETE
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admoxtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. "(Note :- Cement content considered in this item is @330 kg/cum. "Excess/ less cement used as per design mix is payable/ recoverable separately).
All works upto plinth level.
Concrete of M25 grade with minimum cement content of 330 kg /cum
251
-
-
All works above plinth level.
Concrete of M25 grade with minimum cement content of 330 kg /cum
263
-
-
BRICK WORK
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
Cement Mortar 1:4 (1 cement : 4 coarse sand).
5.2
-
-
Cement Mortar 1:6 (1 cement : 6 coarse sand).
130
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :
Cement mortar 1:4 (1 cement : 4 coarse sand)
0.5
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
Cement mortar 1:4 (1 cement : 4 coarse sand).
1186
-
-
Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.
(a). Brick on flat soling.
1281
-
-
CLADDING WORK
Providing and fixing 18mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
Raj Nagar Plain white marble/ Udaipur green marble/ Zebra
black marble
Area of slab over 0.50 sqm
191
-
-
Granite of any colour and shade
Area of slab over 0.50 sqm.
17
-
-
Providing edge moulding to 18mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge.
Marble work
163
-
-
Granite Work
14
-
-
Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge, in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
197
-
-
WOOD AND P.V.C. WORK
Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately):
12 mm thick
250
-
-
18 mm thick
270
-
-
Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part-I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters :
35mm thick including ISI marked Stainless Steel butt hinges with necessary screw.
94
-
-
Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete :
25 mm dia
50
-
-
M.S. GRILL
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flates, square or round bars etc. including priming coat with approved steel primer all complete.
Fixed to openings / wooden frames with rawl plugs screws etc.
1100
-
-
BRASS FITTINGS
Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :
250x10 mm
60
-
-
Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.
40 mm
72
-
-
Providing and fixing bright finished brass handles with screws etc. complete:
125 mm
90
-
-
75 mm
144
-
-
ALUMINIUM FITTINGS
Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
2
-
-
Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.
Double strip (horizontal type)
144
-
-
Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
Single rubber stopper
25
-
-
Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.
19
-
-
Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screws etc. complete :
250x16 mm
10
-
-
STEEL WORK
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge
Profile B
Fixing with adjustable lugs with split end tail to each jamb.
250
-
-
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
Hot finished seamless type tubes
4750
-
-
Providing and fixing circular/ hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140mm, 73mm height, top lid of 1,5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M,S, sheet box by means of 3.3mm dia round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standared drawing.
34
-
-
SS RAILING
Providing and fixing stainless steel (Grade304) railing made of hollow tubes, channels, plated etc., including welding, grinding, buffing, polishing and making curvature (whereever required) and fitting the same with necessary stainless steel nuts and bolts complets, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
848
-
-
FLOORING
Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).
Light shade pigment using white cement
20
-
-
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
Glazed Vitrified tiles Matt / Antiskid finish of size
Size of Tile 600x600 mm
95
-
-
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.
Size of Tile 500x500 mm
755
-
-
ROOFING
Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm center to centre, one flange fixed to the ceilling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200mm center to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5mm, at 459mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm dia x 230mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mmc/c, including jointing and finishing to a flush finish of tapered (Contd....)
-
-
-
and square edge of the board with recomended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer-in-charge but excluding the cost of painting with :
12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)
70
-
-
ROOFING SHEET & ACCESSORIES
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
228
-
-
Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
Ridges plain (500 - 600mm)
75
-
-
Barge board (Upto 300 mm)
151
-
-
FINISHING
CEMENT PLASTER (IN FINE SAND)
12 mm cement plaster of mix :
1:6 (1 cement: 6 fine sand)
3568
-
-
15 mm cement plaster on rough side of single or half brick wall
of mix:
1:6 (1 cement: 6 fine sand)
965
-
-
CEMENT PLASTER (IN COARSE SAND)
15mm cement plaster on rough side of single or half brick wall of mix :
1:4 (1 cement : 4 coarse sand)
41
-
-
Neat cement punning.
25.5
-
-
PLAIN CEMENT MORTAR BANDS
18 mm thick plain cement mortar band in cement mortar 1:4 (1 cement : 4 fine sand):
Raised Band
362
-
-
POINTING ON BRICK WORK
Pointing on tile brick work with cement mortar 1:3 (1 cement : 3 fine sand):
Flush/ Ruled/ Struck or weathered pointing
217
-
-
FINISHING
EXTERIOR FINISHING
Finishing walls with Acrylic Smooth exterior paint of required shade :
New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
1144
-
-
WALL PUTTY
Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
4331
-
-
INTERIOR FINISHING
Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :
Water thinnable cement primer
3223
-
-
Wall painting with premium acrylic emulsion paint of interior grade,having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.
Two coats
3223
-
-
Applying priming coat: STEEL & WOODEN SURFACE
With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)
1078
-
-
With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works.
111
-
-
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
Two or more coats on new work
1189
-
-
DRAINAGE
Supplying and fixing C.I. cover without frame for manholes :
500 mm diameter C.I. cover (medium duty) the weight of
the cover to be not less than 58 kg
2
-
-
ALUMINIUM WORK
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, buttoms and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
For fixed portion
Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
1746
-
-
For shutters of doors, windows & ventilators including providing and fixing hings/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)
Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
1521
-
-
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) :
With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)
165
-
-
WATER PROOFING
Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :
(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.
(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
38
-
-
Providing and applying intehral crystalline slurry of hydrophillic in nature for water proofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservoir, sewage & water treatment plant, tunnels/ subway and bridge deck etc., prepared by mixing in the ratio of 5:2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3:1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self healing of cracks upto a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guaranteed for 10 years against any leakage.
For vertical surface two coats @0.70 kg per sqm per coat.
63
-
-
For horizontal surface one coat @ 1.10 kg per sqm.
490
-
-
PLUMBING & SANITARY WORKS
-
-
-
INTERNAL PLUMBING WORKS :
SANITARY FIXTURES
INDIAN TYPE WATER CLOSET (WC)
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:
White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests
3
-
-
EUROPEAN TYPE WATER CLOSET (WC)
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :
W.C. pan with ISI marked white solid plastic seat and lid
4
-
-
WASH BASIN
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps
9
-
-
KITCHEN SINK (STAINLESS STEEL)
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :
Kitchen sink without drain board
610x510 mm bowl depth 200 mm
4
-
-
FITTINGS & ACCESSORIES
MIRROR
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
9
-
-
SOAP TRAY,SOAP DISH,LIQUID SOAP DISPENSER AND LIQUID SOAP CONTAINER
Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
1
-
-
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.
8
-
-
TOWEL RAIL,TOWEL RACK & TOWEL RING
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.
450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.
16
-
-
ROBE HOOK
Providing and fixing bright finished brass hard drawn hooks and eyes
300 mm
16
-
-
TOILET PAPER HOLDER
Providing and fixing toilet paper holder :
C.P. brass
7
-
-
Providing and fixing P.V.C. WC connector (straight or bend type) with rubber lip ring. Including 110 mm dia PVC pipe / bend of required length and proper connection with M seal to C.I. pipe complete as required
7
-
-
WASTE COUPLING
Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.
Waste coupling 38 mm dia of 83 mm length and 77mm
breadth, weighing not less than 60 gms
13
-
-
BOTTLE TRAP
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
13
-
-
BIB COCK
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore
7
-
-
Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.
15 mm nominal bore
6
-
-
STOP COCK / ANGULAR VALVE
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931
15mm nominal bore
32
-
-
HEALTH FAUCET
Providing, fixing, testing and commissioning of CP Brass Health Faucet with nuts, washers of approved brand including cutting and making good the walls wherever required. Rate of flow should be 4 LPM
7
-
-
Providing and fixing Floor trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.
23
-
-
Providing and fixing medium duty CP Floor grating with frame of approved design brand including setting in floor with cement motor to match with floor finish as per architect requirement including cutting and making good floor or wall wherever required.
a) 110mm dia
23
-
-
Providing and fixing medium duty CI grating (for RWP) with frame of approved design brand including setting in floor with cement motor to match with floor finish as per architect requirement including cutting and making good floor or wall wherever required.
a) 110mm dia
14
-
-
PILLAR COCK & SINK COCK
Providing & fixing, testing and commissioning of counter mounted C.P. brass pillar cock with aerator for wash basins of approved brand.
9
-
-
Providing & fixing, testing and commissioning of wall mounted C.P. brass Sink cock of approved brand including cutting and making good the wall/floor wherever required.
4
-
-
SHOWER
Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.
a) 15 mm nominal dia
7
-
-
Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
150 mm diameter
7
-
-
Providing and fixing C.P. brass stop cock (concealed) of standard
15 mm nominal bore
7
-
-
SOIL, WASTE & VENT PIPES Providing, fixing, testing and commissioning of uPVC SWR pipe confirming to IS-13592, Type-B cut to required lengths including all necessary fittings and special such as bends, junctions offset, access pieces (plain or door), Tees, bends, reducers, flanges, plugs unions and clamps Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly epoxy coated including chasing, cutting and making good the walls / floor etc. wherever required
a)110 mm O.D type "B"
75
-
-
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
Semi rigid pipe
32 mm dia
15
-
-
40 mm dia
20
-
-
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming ro IS:13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion.
(i) Single socketed pipes.
110 mm diameter.
75
-
-
Providing and fixing wall faced unplasticised PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion.
Bend 87.5°
110mm bend.
14
-
-
Shoe (Plain)
110mm Shoe.
14
-
-
Providing and fixing unplasticised PVC pipe clip of approved design to unplasticised PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required lingth, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.
110mm.
70
-
-
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighing not less than 440 grams.
14
-
-
Providing and fixing uPVC cowl complete including cutting and making good the walls and floors wherever required.
a) 110 OD
2
-
-
Providing & fixing M.S. structural work fabricated from standard section e.g. M.S rounds, angles, channels, plates including cutting to size,drilling,welding fixing and welding to insert plates in RCC structural members as directed by engineer-in-charge including cutting and making good the walls, ceilings and floors (for pipe supports, clamps etc.)
30
-
-
WATER SUPPLY PIPING
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.
CONCEALED WORK , Including cutting chases and making good the walls
15 mm dia Pipes
20
-
-
20 mm dia Pipes
25
-
-
25 mm dia Pipes
30
-
-
32 mm dia Pipes
50
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc)
EXTERNAL WORK
40 mm dia Pipes
15
-
-
50 mm dia Pipes
20
-
-
65 mm dia Pipes
70
-
-
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
32 mm nominal bore.
2
-
-
40 mm nominal bore.
3
-
-
50 mm nominal bore.
2
-
-
OVERHEAD WATER TANK
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
10000
-
-
EXTERNAL PLUMBING WORKS :
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:
100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
2
-
-
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
4
-
-
ELECTRICAL WORK
-
-
-
SUB HEAD : A - WIRING
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required
Group C
158
-
-
Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required
Group C
100
-
-
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required
800
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
850
-
-
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
1200
-
-
2 X 6 sq. mm + 1 X 6 sq. mm earth wire
30
-
-
4x6 sq.mm + 2x6 sq.mm earth wire
150
-
-
4x10 sq.mm + 2x6 sq.mm earth wire
170
-
-
Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required
2 pair
110
-
-
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
25mm
200
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
Telephone socket outlet
2
-
-
Bell push
1
-
-
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required
40
-
-
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
40
-
-
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.
1 or 2 Module (75mmX75mm)
2
-
-
3 Module (100mmX75mm)
2
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
15
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
29
-
-
Installation, tesitng and commissioning of pre-wired fluorescent fitting/compact fluorescent fitting of all types , complete with all accessories and tube etc. directly on ceiling/wall, including connection witn 1.5 sq.mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.
100
-
-
Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.
40
-
-
Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.
Upto 450 mm sweep
14
-
-
Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required.
107
-
-
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel / PVC conduit as required.
1 run of cable
110
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/ 6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).
40
-
-
Supplying and fixing of Krone telephone tag blocks, of the following capacities including termination of paired wires, in 2mm thick M.S. box with hinged metal cover duly painted and labelled as required. 10 pair Tag Box (with 1no 10 pair tag block)
1
-
-
Supplying and fixing certified Cat6 RJ45 data outlet onto existing faceplate with specified colour coding including termination of the Cat6 UTP cable at BOTH ends
2
-
-
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator
6 way (4 + 18), Double door
7
-
-
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
Single pole
130
-
-
Triple pole and neutra
7
-
-
Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required
25 A
9
-
-
40 A
12
-
-
Supplying of heavy duty XLPE insulated and PVC sheathed 1.1 kV grade conforming to IS:7098 Part-1/ IS:1554 Part-1 for aluminium/ copper conductor unarmoured/ armoured cable of the following sizes including fastening with nylon ties (internal), or galvanised MS saddles (external) as required. Cable to be drawn through existing trenches or laid on existing cable trays/ ladders.
3.5c 50 sqmm aluminium armoured cable.
90
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.
Above 35 sq. mm and upto 95 sq. mm
90
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required
3½ X 50 sq. mm (35 mm)
2
-
-
Providing and laying of the following types & sizes of pipes including excavation and backfilling of trenches with proper base levelling and preparation with PCC where required in external spaces (excluding the cost of making suitably sized manholes) as specifed with brick plastered with water-proof compound and all required accessories for coupling, fixing and supports where required for internal use:
180/160 mm HDPE Double wall corrugated (DWC) pipe (laid underground in external spaces)
90
-
-
125 mm HDPE Double wall corrugated (DWC) pipe (laid underground in external spaces)
90
-
-
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required
300 mm width X 50 mm depth X 1.6 mm thickness
10
-
-
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required
300 mm width X 50 mm depth X 1.6 mm thickness
5
-
-
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
2
-
-
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
40
-
-
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required
40
-
-
Supply the following lighting fixtures including, sampling, preparing inventory, storing, assembling, testing and fixing with all required supports and complete with supplying and fixing suitable lamps, ballasts (all fluorescent fixtures to have low THD electronic ballasts), condensors, ignitors, transformer, starters, with all necessary accessories for fixing or mounting fixtures in location viz down rods, suspension cables or chains, dash fasteners of suitable strength etc. as required. 20W Surface, Wall mounted or suspended type LED fixture with 2500 Lumen output, Philips Cat no.smart bright extra batten,BN 308C LED 20S L120 PSU or approved equivalent..
100
-
-
12W, Surface mounted LED Downlight fixture with 1200 Lumen output, Philips Cat no. SM250C LED12S.or approved equivalent..
107
-
-
Supplying of high speed A.C. ceiling fan, 5 star rating complete with all accessories down rod, canopy etc. of following sweeps with making necessary connections atc.as required complete and as directed by the department (without regulator).
1200 mm sweep
40
-
-
Supplying of enegy efficent A.C. Exhaust fan in the existing hole on the wall of following sweeps and making necessary connections etc., as required complete and as directed by the Department.
Heavy duty for 900/ 960 rpm
300 mm sweep
14
-
-
Supply, installation, unloading, storing, fixing in position, testing and commissioning the following sheet steel cubicle type fully compartmentalized panels fabricated from 1.6mm thick CRCA sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply and cable alley should be suitable for cable entry from top or bottom and with segregated bus-bar chamber with bus bars as specified below and including supplying and fixing following switchgears, meters and accessories, inter-connections, bonding to earth, powder coated painting and marking as specified. Switch boards complete as per schematic diagram:
Type of construction: Form 3
Indoor IP classification: 42
Colour: Siemens Gray Powder Coated, as per approved sample.
The BOQ shall be read in conjuction with general notes, specification and single line diagram (attached for ref.) In case of any disrepancy between specification, BOQ and SLD, the same shall be brought to the notice of Client/ Consultant before quoting the rates, otherwise stringent condition shall be deemed to have been considered. (Contd..)
-
-
-
All MCCB shall be with door interlocked rotary handle with ON/TRIP/OFF position indicator, continuous variable thermal magnetic O/C and S/C releases. The MCCB 250A and above 250A rating shall be provided with microprocessor based releases (settable at site). Incomer MCCB shall be provided with E/F release also.
All feeder doors shall have pad locking arrangement.
All TP Feeders shall have solid isolable neutral link.
Cable entries provisions shall be from the TOP and BOTTOM.
The internal control wiring shall be fuseless. All control wiring and metering protection shall be by MCB's. Removable lifting hook shall be provided in all transportation section.
All bus bar shall be insulated with coloured PVC sleeve i.e. Red, Yellow, Blue and Black as per colour code.internal wiring of panel shall be with size 2.5sqmm flexible copper conductor for Cast Resin Type CT circuit and control wiring with 1.5sqmm.
All indicating light shall be LED type.
The contractor shall prepare proper GA drawings and shall seek approval for these from the project manager / electrical consultant prior to construction of all panels and boards.
All live accessible parts shall be shrouded with 3mm thick polycarbonate /FRP sheet and all equipment shall be finger touch proof . (Contd...)
-
-
-
Light & Power MDB:-
INCOMER 1no. 100A, 25kA TPN MCCB with rotary operating handle with door interlock with thermal-magnetic release for O/L, S/C setting of 80%-100%, and ON /TRIP/ OFF indication.
1no 96mm x 96mm multi parameter digital meter with LCD display for Voltage, Current, Frequency, Power, Energy and power factor with set of suitably sized Cast Resin Type CTs including protection with 2A SP MCB
1 set of three phase indicating lamps with suitable protection. Bus bar: Equally sized three phase & neutral aluminium conductors busbar suitably sized to carry 160A current having a maximum current density of 1.0 amp per sq.mm and suitably insulated with coloured heat shrinkable PVC Sleeve i.e. RYB, BK as per colour code.
4nos. 16A HRC fuse with Class "II" surge arrestors, less then 1.5 kV, 40kA, 8/20 micro second, as per specification.
Outgoings: 6no 40A TPN MCBs, 10kA (C Curve)
6no 25A TPN MCBs, 10kA (C Curve)
1No. 25x6 mm Aluminium Earth Bus strip across the width of the Panel .
Light & Power MDB completed as above
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements