Dibrugarh University Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 2,90,008Document Cost
₹ 1,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2022_DU_27030_1Bid Award Id
ViewTender No
DU/PC/TQ/187/1410Tender Authority
Dibrugarh University ViewPurchaser Address
-Website
http://https://dibru.ac.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos / Lindane emulsifiable concentrate of 20%
432
-
200.9
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
240
-
256.15
1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20mm nominal size).
24
-
6833.4
1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)
11
-
6326.05
Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)
14
-
370.85
Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.
14
-
113.85
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20mm nominal size) over 75mm thick bed of dry brick ballast 40mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling, dressing & finishing the top smooth.
170
-
681.65
Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete
63
-
307.95
Suspended floors, roofs, landings, balconies and access
platform
132
-
766.55
Lintels, beams, plinth beams, girders, bressumers and cantilevers.
428
-
608.35
Columns, pillars, piers, abutments, posts and struts.
160
-
804.25
Extra for shuttering in circular work (20% of respective centering and shuttering items)
32
-
160.85
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
4366
-
89.65
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
6726
-
89.65
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admoxtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. "(Note :- Cement content considered in this item is @330 kg/cum. "Excess/ less cement used as per design mix is payable/ recoverable separately). All works upto plinth level. Concrete of M25 grade with minimum cement content of 330 kg /cum
37
-
7997.3
All works above plinth level upto floor V level. Concrete of M25 grade with minimum cement content of 330 kg /cum
57
-
10080.15
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement Mortar 1:4 (1 cement : 4 coarse sand).
30
-
6882
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement : 4 coarse sand).
500
-
1018.05
Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a). Brick on flat soling.
314
-
515
Providing and fixing 18mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 sqm.
12
-
4425.35
Providing edge moulding to 18mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge. Granite Work
18
-
418.85
Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.
5
-
808.15
Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge, in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
75
-
1063.45
Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately): 12 mm thick
80
-
667.1
Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately): 18 mm thick
120
-
869.1
Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part-I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35mm thick including ISI marked Stainless Steel butt hinges with necessary screw
27
-
2015.75
Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 25 mm dia
60
-
482.3
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flates, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings / wooden frames with rawl plugs screws etc.
845
-
197.7
Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm
25
-
374.35
Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 40 mm
16
-
264.9
Providing and fixing bright finished brass handles with screws etc. complete: 125 mm
42
-
205.1
Providing and fixing bright finished brass handles with screws etc. complete: 75 mm
16
-
149.7
Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. Double strip (horizontal type)
9
-
856.3
Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. Double strip (horizontal type)
16
-
34.15
Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper
10
-
35.5
Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.
12
-
739.8
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge Profile B Fixing with adjustable lugs with split end tail to each jamb.
66
-
444.5
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes
8910
-
168.95
Providing and fixing circular/ hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140mm, 73mm height, top lid of 1,5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M,S, sheet box by means of 3.3mm dia round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standared drawing.
22
-
185.2
Providing and fixing stainless steel (Grade304) railing made of hollow tubes, channels, plated etc., including welding, grinding, buffing, polishing and making curvature (whereever required) and fitting the same with necessary stainless steel nuts and bolts complets, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
160
-
612.25
Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Light shade pigment using white cement
80
-
1233.05
Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Udaipur green marble
60
-
2100.4
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including
grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt / Antiskid finish of size Size of Tile 600x600 mm
12
-
1311.05
Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm
240
-
1676.15
Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 800x800 mm
240
-
205.15
Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm center to centre, one flange fixed to the ceilling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200mm center to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5mm, at 459mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm dia x 230mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mmc/c, including jointing and finishing to a flush finish of tapered and square edge of the board with recomended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer-in-charge but excluding the cost of painting with : 12.50 mm thick tapered edge Gypsum Plain board conforming to IS : 2095 - (Part I) : 2011 (Board with BIS certification mark)
154
-
1145.95
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
550
-
671.55
Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)
235
-
450.6
Flashings/ Aprons.( Upto 600 mm)
170
-
412.85
Barge board (Upto 300 mm)
170
-
384.2
Gutter( 600 mm over all girth )
120
-
1110.6
12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)
1060
-
307.25
15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)
570
-
354.5
18 mm thick plain cement mortar band in cement mortar 1:4 (1 cement : 4 fine sand): Raised Band
216
-
9.55
Pointing on tile brick work with cement mortar 1:3 (1 cement : 3 fine sand): Flush/ Ruled/ Struck or weathered pointing
160
-
292.05
Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
570
-
166.85
Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
1555
-
123.85
Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer
985
-
64.45
Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats
985
-
116.05
With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)
374
-
61.45
With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works.
82
-
55.5
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
456
-
131.45
Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in-Charge. 14.4.1 For door/ window/ clerestory window
20
-
1046.95
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, buttoms and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)
478
-
466.3
For shutters of doors, windows & ventilators including providing and fixing hings/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)
169
-
564.8
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) : With float glass panes of 5.50mm thickness.
52
-
1325.55
Providing and applying intehral crystalline slurry of hydrophillic in nature for water proofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservoir, sewage & water treatment plant, tunnels/ subway and bridge deck etc., prepared by mixing in the ratio of 5:2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3:1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self healing of cracks upto a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guaranteed for 10 years against any leakage. For vertical surface two coats @0.70 kg per sqm per coat.
12
-
406.25
Providing and applying intehral crystalline slurry of hydrophillic in nature for water proofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservoir, sewage & water treatment plant, tunnels/ subway and bridge deck etc., prepared by mixing in the ratio of 5:2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3:1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self healing of cracks upto a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guaranteed for 10 years against any leakage. For horizontal surface one coat @ 1.10 kg per sqm.
72
-
311.5
Providing and fixing of rebars of new rcc members to the existing / old rcc member by rebar anchoring using FISCHER-E390 or HILTI - RE 500(V3) chemical. (a) 16 mm dia Rebar
150
-
500
Providing and fixing of rebars of new rcc members to the existing / old rcc member by rebar anchoring using FISCHER-E390 or HILTI - RE 500(V3) chemical. (a) 8 mm dia Rebar
30
-
250
Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.
10
-
13036.55
Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing
cistern
1
-
10128.3
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm with
a pair of 15 mm C.P. brass pillar taps
10
-
3158.7
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x510 mm bowl depth 200 mm
5
-
4274.4
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
10
-
1411.15
Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
1
-
96.75
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.
16
-
146.3
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm,
78 mm wide and effective height of 88 mm, weighing not
less than 170 gms.
16
-
573.6
Providing and fixing bright finished brass hard drawn hooks and eyes 300 mm
10
-
86.85
Providing and fixing toilet paper holder : C.P. brass
10
-
680.8
Providing and fixing P.V.C. WC connector (straight or bend type) with rubber lip ring. Including 110 mm dia PVC pipe / bend of required length and proper connection with M seal to C.I. pipe complete as required
10
-
532
Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm
breadth, weighing not less than 60 gms
16
-
109.7
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
15
-
886.25
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore
10
-
434.2
Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore
2
-
715.05
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore
30
-
500.35
Providing, fixing, testing and commissioning of CP Brass Health Faucet with nuts, washers of approved brand including cutting and making good the walls wherever required. Rate of flow should be 4 LPM
10
-
2185
Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :
22
-
2109
Providing and fixing medium duty CP Floor grating with frame of approved design brand including setting in floor with cement motor to match with floor finish as per architect requirement including cutting and making good floor or wall wherever required. a) 110mm dia
22
-
360
Providing and fixing medium duty CI grating (for RWP) with frame of approved design brand including setting in floor with cement motor to match with floor finish as per architect requirement including cutting and making good floor or wall wherever required. a) 110mm dia
15
-
360
Providing & fixing, testing and commissioning of counter mounted C.P. brass pillar cock with aerator for wash basins of approved brand.
10
-
909
Providing & fixing, testing and commissioning of wall mounted C.P. brass Sink cock of approved brand including cutting and making good the wall/floor wherever required.
5
-
1728
Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. a) 15 mm nominal dia
7
-
6119.15
Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter
7
-
190.1
Providing and fixing C.P. brass stop cock (concealed) of standard 15 mm nominal bore
7
-
594.75
Providing, fixing, testing and commissioning of uPVC SWR pipe confirming to IS-13592, Type-B cut to required lengths including all necessary fittings and special such as bends, junctions offset, access pieces (plain or door), Tees, bends, reducers, flanges, plugs unions and clamps Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly epoxy coated including chasing, cutting and making good the walls / floor etc. wherever required a)110 mm O.D type "B"
70
-
1180.8
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia
10
-
90.95
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40 mm dia
2
-
101.65
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming ro IS:13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion. Single socketed pipes. 110 mm diameter.
120
-
319.75
Providing and fixing wall faced unplasticised PVC moulded fittings accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion. Coupler 110mm
30
-
119.95
Providing and fixing wall faced unplasticised PVC moulded fittings accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion. Bend 87.5° 110mm bend.
15
-
132
Providing and fixing wall faced unplasticised PVC moulded fittings accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion. Shoe (Plain) 110mm Shoe
15
-
115.95
Providing and fixing unplasticised PVC pipe clip of approved design to unplasticised PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required lingth, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm.
60
-
309.5
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighing not less than 440 grams.
15
-
47.9
Providing and fixing uPVC cowl complete including cutting and making good the walls and floors wherever required. a) 110 od
2
-
71
Providing & fixing M.S. structural work fabricated from standard section e.g. M.S rounds, angles, channels, plates including cutting to size,drilling,welding fixing and welding to insert plates in RCC structural members as directed by engineer-in-charge including cutting and making good the walls, ceilings and floors (for pipe supports, clamps etc.)
50
-
77
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) b) 20 mm dia
80
-
275.25
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) c) 25 mm dia
30
-
370.65
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) d) 32 mm dia
40
-
435.05
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) e) 40 mm dia
60
-
559.2
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore
2
-
461.75
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore.
2
-
589.9
Fixing automatic high pressure electric water heaters with glass lining thermostats with each element and high temperature cut off, necessary insulation, safety valve, 15 mm dia 600 mm long flexible pipe etc., all complete. a) 15 Ltr Capacity
7
-
6050
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : a) 100 mm dia
1
-
447.25
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : b) 150 mm dia
35
-
493.1
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : c) 250 mm dia
25
-
811.15
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : d) 300 mm dia
20
-
902.05
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
4
-
2453.55
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : a) Inside size 45 x 45 cm and depth up to 60 cm
5
-
16500
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : b) Inside size 90 x 90 cm and depth up to 75 cm
10
-
22500
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
15
-
11687.1
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
290
-
990
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch
60
-
85
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 A switch
55
-
132
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 A socket outlet
60
-
111
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 A socket outlet
55
-
175
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
100
-
32
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)
10
-
243
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm)
204
-
267
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 4 Module (125mmX75mm)
4
-
287
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 6 Module (200mmX75mm)
30
-
333
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 8 Module (125mmX125mm)
53
-
383
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 12 Module (200mmX150mm)
8
-
434
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/Isolator) 6 way (4 + 18), Double door
1
-
3693
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/Isolator) 8 way (4 + 24), Double door
1
-
4601
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/Isolator) 12 way (4 + 36), Double door
3
-
25000
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/Isolator) 16 way (4 + 48), Double door
1
-
34000
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
200
-
199
Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A Four pole isolator
8
-
832
Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
40
-
8
Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 A
15
-
1927
Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A
9
-
2095
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm
270
-
39
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm
MS flat clamp)
100
-
104
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 core x 6.0 sq. mm. XLPE, Al.armoured cable.
6
-
210
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 core x 10.0 sq. mm. XLPE, Al.armoured cable.
6
-
219
4 core x 10.0 sq. mm. XLPE, Al.armoured cable.
4
-
250
3.5 core x 95 sq. mm. XLPE, Al.armoured cable.
6
-
473
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
100
-
146
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
200
-
167
2 X 4 sq. mm + 1 X 4 sq. mm earth wire
200
-
200
4 X 6 sq. mm + 2 X 6 sq. mm earth wire
10
-
394
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
8
-
6216
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (with charcoal/ coke and salt ) as required.
2
-
11794
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
30
-
131
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
25
-
483
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
80
-
206
Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required
80
-
108
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.
20
-
37
Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.
10
-
1224
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm
60
-
84
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm
60
-
90
Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness
80
-
531
450 mm width X 50 mm depth X 1.6 mm thickness
15
-
700
Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting
suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness
10
-
947
450 mm width X 50 mm depth X 1.6 mm thickness
6
-
2089
Supply, Installation, testing & commissioning of compartmentalized type Lighting / Power Distribution boards as per Drawing, Specification. The unit rate shall include loading/unloading, shifting from site store to the place of installation, assembling the Panel including mounting & wiring of loose parts by manufacturers, interconnection of shipping sections, installation on readymade Cable trench (provied support for panel mounting) or directly on floor, assembling of loose accessories supplied by the manufacturer, wiring & connection of auxiliary circuits, installation, testing & commissioning of all Panel, supply of all necessary hardware. Aligning, levelling, grouting, testing and setting of relays and meters including all. INCOMING: 1 No. 160 amps TPN MCCB with following accessories : VAF digital electronic meter with inbuilt selector switch and 160/5 Amps suitable VA, CL 1 CTs . - 1 Set Phase indicating light shall be protected by 2 Amps MCB’s. - 3 Sets Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set BUSBAR SECTION-1 200 Amps TPN Aluminiun bus bars with heat coloured shrinkable insulation sleeve. - 1 Set 160A,FP ATS OUTGOING: 40 Amps TPN MCB - 8 Nos. PANEL AS ABOVE(Refer SLD)
1
-
126688.96
Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed aluminium conductor armoured cables as per specification. 4 core x 6.0 sq. mm. XLPE, Al.armoured cable.
170
-
129.32
4 core x 10.0 sq. mm. XLPE, Al.armoured cable.
50
-
180
4 core x 16.0 sq. mm. XLPE, Al.armoured cable.
50
-
200
3.5 core x 95 sq. mm. XLPE, Al.armoured cable.
100
-
1580
Installation, testing and commissioning of ceiling fan,wiring the down rods of standard length (upto 30 cm) with 1.5 sq. including mm FR PVC insulated, copper conductor, single core cable,including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
73
-
203
Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.
4
-
98
Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor,single core cable and earthing etc. as required.
262
-
168
Supplying with fitting fixing of luminaries complete with all accessories such as ballast, starter etc. directly on wall / ceiling including connection as approved by the Deptt.)with 1.5 sq mm P.V.C. insulated S.C. copper conductor as required and as directed by the department. Supply of 20 watt LED tube (Panasonic make) Model- PANASONIC PBTM08204 with or equivalent (Equivalent will be selected by the deptt considering the mother items rate) PHILIPS/ WIPRO/ BAJAJ/ Havells/ HPL/ JAQUAR make.
178
-
838.18
Supply of 36 watt LED tube (Panasonic make) Model- PANASONIC PBTM08364 with or equivalent (Equivalent will be selected by the deptt considering the mother items rate) PHILIPS/ WIPRO/ BAJAJ/ Havells/ HPL/ JAQUAR make.
13
-
1024.45
Supply of 18 watt (Panasonic make) Model- PANASONIC PDLM26184 or equivalent (Equivalent will be selected by the deptt considering the mother items rate) PHILIPS/ WIPRO/ BAJAJ/ Havells/ HPL/ JAQUAR make.
54
-
1089.64
Supply of 12 watt (Panasonic make) Model- PANASONIC PDLM26124 or equivalent (Equivalent will be selected by the deptt considering the mother items rate) PHILIPS/ WIPRO/ BAJAJ/ Havells/ HPL/ JAQUAR make.
17
-
838.18
24" dia sweep wall bracket fan (BEE 5 star rated) of approved make complete with all accessories.
4
-
7217.69
48" dia sweep ceiling fan (BEE 5 star rated) of approved make complete with all accessories.
73
-
3539
Design, Manufacture, Supply, erection, testing and commissioning of 75 kVA, 415V, 3 Phase, 4 Wire, 50 Hz at 0.8 p.f. prime continuous (actual) rating radiator cooled diesel generating set in acoustic enclosure with radiator, Water cooled engine, PMG, base frame, Alternator, Static Excitation System, Lube Oil System, Electronic Governor, 24V Batteries & Battery Charger, Instrumentation, day oil fuel tank, Residential Silencer with Bellows, Alarms, microprocessor based Engine Control Panel, AVR Panel ,equivalent for AMF facility, termination adopter box suitable for XLPE insulated aluminium cables, drip trays space for mounting all associated equipments/ works as per specification including providing common base plate, anti vibration isolators, foundation bolts etc.
The civil works for foundation for D.G.Set shall not be included in the rate. But other accessories like grouting screws, anti-vibration pads etc. shall be included in the rate.
Alternator shall have class H insulation and rated for 100 KW output at 50°C. Emergency stop push button for individual DG set shall be located at the exit door. Engine shall not be derated upto 50 deg.C ambient.
Note: Piping between day oil tank & DG set shall be included.
1
-
842160
Cat6, 4 Pair 23 AWG U/UTP, IEC 60332-3-22 Flame Rated LSZH Cable
10
-
10800
Supply,Installation, Testing and Commissioning of following At Rack Side KeyConnect Angled Patch Panel, 24-port, 1U, Black (Empty)
5
-
12300
Supply,Installation, Testing and Commissioning of following At Rack Side Cat6 Modular Jack, Keyconnect, Blue Color for Data
50
-
360
Supply,Installation, Testing and Commissioning of following At Rack Side Cat6 Modular Jack, Keyconnect, Blue Color for Voice
50
-
360
Supply,Installation, Testing and Commissioning of following At Rack Side Cable Support Bar for above Patch Panel ( optional)
4
-
715
Supply,Installation, Testing and Commissioning of following At Rack Side Cat 6 Patch cord - 2 Mtr - Blue , LSZH for Data
50
-
400
Supply,Installation, Testing and Commissioning of following At Rack Side Cat 6 Patch cord - 2 Mtr - Yellow , LSZH for voice
50
-
400
Supply,Installation, Testing and Commissioning of following At Field end Cat6 Modular Jack, Keyconnect, Blue Color for Data
50
-
400
Supply,Installation, Testing and Commissioning of following At Field end Cat6 Modular Jack, Keyconnect, Blue Color for Voice
50
-
400
Supply,Installation, Testing and Commissioning of following At Field end Cat 6 Patch cord - 2 Mtr - Blue , LSZH for Data
50
-
360
Supply,Installation, Testing and Commissioning of following At Field end Cat 6 Patch cord - 2 Mtr - Yellow , LSZH for voice
50
-
360
Supply,Installation, Testing and Commissioning of following At Field end Dual Face plate UK type square, Double Plate
50
-
860
Supply,Installation, Testing and Commissioning of following FIBER BACK BONE - FIRST FLOOR MAIN CROSS CONNECT TO ALL HUB ROOMS ( INTER FLOOR) - TWO FIBER RUNS OF 6 CORE TO EACH HUB ROOM FROM PRIMARY & SECONDARY ROUTE IN RING TYPE ARCHITECTURE 6 Core Singlemode 9/125 ITU G.657A1 Bend Insensitive distribution cable with Corrugated Steel Tape Armor (CST) and Double LSNH Jacket, Universal (Indoor/Outdoor) with Full Rodent Protection, IEC 60332-3-22 Direct Burial
50
-
350
1U 2 slots Rack mount Patch panel, Including 1 x 24F splice tray i) 12F LC Duplex adapter strip, Ceramic sleeve for SM ( 4 Nos.) ii). Simplex Pigtail, LC Simplex - Open, Singlemode, 900um, 2MT, Yellow ( 24+32=56 Nos.)
3
-
46600
Duplex Patch Cords, LC Duplex - LC Duplex, Singlemode, Riser, Duplex Zip Cord 2.0mm, 3MT, Yellow
24
-
2500
Supply,Installation, Testing and Commissioning of following FIBER BACK BONE - From HUBROOM ( INTRA FLOOR) TWO FIBERS RUNS OF 6 CORE EACH FROM PRIMARY & SECONDARY ROUTE 6 Core Singlemode 9/125 ITU G.657A1 Bend Insensitive distribution cable with Corrugated Steel Tape Armor (CST) and Double LSNH Jacket, Universal (Indoor/Outdoor) with Full Rodent Protection, IEC 60332-3-22 Direct Burial
50
-
242.06
1U 2 slots Rack mount Patch panel, Including 1 x 24F splice tray i). 12F LC Duplex adapter strip, Ceramic sleeve for SM ( 4 Nos.) ii). Simplex Pigtail, LC Simplex - Open, Singlemode, 900um, 2MT, Yellow ( 24 Nos.)
3
-
34142.83
Duplex Patch Cords, LC Duplex - LC Duplex, Singlemode, Riser, Duplex Zip Cord 2.0mm, 3MT, Yellow
32
-
3152.74
Supply,Installation, Testing and Commissioning of 42 U Rack 600X600 with all standard accessories
1
-
101725.92
Supply,Installation, Testing and Commissioning of 12 U Rack 600X600 with all standard accessories
2
-
40282.99
15U Network Rack with STD Accessories
2
-
20000
42U Server Rack (600 x 1000) with 1 x KBD Tray, 1 x Monitor Tray, Front Glass Door, Rear Perforated Door, 2 x Power Strip, 2 x Cable Manager and other accessories
1
-
65000
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements