Department Of Housing And Urban Affairs Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 61,15,000Document Cost
₹ 20,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2022_DHUA_25452_1Bid Award Id
ViewTender No
CE/H and UA/17/PT-II/21-22/42, date07/05/2022Tender Authority
Department Of Housing And Urban Affairs ViewPurchaser Address
-Website
http://assamtenders.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
Plain cement concrete apron in prop 1:4:8 with 20mm down graded coarse agg. Over soling including neat cement finish using cement slurry 2.75Kg. of cement per sq.m. of floor (soling to be measured separately) (b) . 50mm thick
74.6
-
-
Concrete work
-
-
-
PLAIN CEMENT CONCRETE WORKS: Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
1144.31
-
-
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
249.6
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)
1707.3
-
-
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
1503.68
-
-
Form work
-
-
-
Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete
4233.44
-
-
Columns, Pillars, Piers, Abutments, Posts and Struts
2929.74
-
-
Lintels, beams, plinth beams, girders, bressumers and cantilevers
3840.97
-
-
Suspended floors, roofs, landings, balconies and access platform
4840.62
-
-
Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
40.32
-
-
Stairs, (excluding landings) except spiral-staircases
546.21
-
-
BRICK WORKS
-
-
-
Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
12506.4
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)
396.04
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand
3046.79
-
-
FLOORING WORKS
-
-
-
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate
90
-
-
MARBLE FLOORING : Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Raj Nagar plain
5.4
-
-
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
5863.11
-
-
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
996.51
-
-
GRANITE FLOORING : Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red
395.33
-
-
(C) PAVERS : Providing and laying 500x500x40 mm thick paver on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge.
2878.61
-
-
ANTISKID TILES : Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size . Size of Tile 600 x 600 mm
309.22
-
-
PLASTERING WORKS
-
-
-
12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)
116.91
-
-
15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)
16172.87
-
-
Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): Flush / Ruled/ Struck or weathered pointing
2336.83
-
-
CEILING WORKS
-
-
-
Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987,Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanised iron section of 0.33mm, thick (galvanized @ 120 grams per sqm including both sides), comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary, intermediate cross-T of size 15x32 mm of length 600mm to form grid, module of size 600 x 600 mm, suspended from ceiling using galvanised, mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded, hanger rod upto 1000 mm length and L-shape level adjuster of size; 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long, dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.
3041.01
-
-
ROOFING
-
-
-
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
2082.46
-
-
Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm)
217.62
-
-
CHOWKATHS
-
-
-
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Sal wood
5.03
-
-
Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately):Second class teak wood.35 mm thick shutters
92.3
-
-
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.
84.15
-
-
GRILL
-
-
-
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. Fixed to openings /wooden frames with rawl plugs screws etc.
14421.12
-
-
ALUMINIUM WINDOWS
-
-
-
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coating 50 micron)
2432.93
-
-
Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels.Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places.
166.32
-
-
PAINTING
-
-
-
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
16955.17
-
-
Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats
19586.41
-
-
PAINTING ON WOOD AND WOOD WOOD BASED SURFACES
-
-
-
Applying priming coat:With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)
336.75
-
-
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
967.65
-
-
PAINTING ON STEEL AND OTHER METAL SURFACE
-
-
-
Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works
1651.65
-
-
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
1009.95
-
-
ALUMINIUM FITTINGS : Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :
-
-
-
300x10 mm
171
-
-
100x10 mm
127
-
-
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150mm
115
-
-
Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.
30
-
-
REINFORCEMENT
-
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
467941.86
-
-
ROOF TRUSS
-
-
-
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete
43778.45
-
-
SS RAILING
-
-
-
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
1477.58
-
-
PILE
-
-
-
Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top of shoe to the bottom of pile cap) : 400 mm dia piles
7528
-
-
REINFORCEMENT
-
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
123447.25
-
-
LOAD TEST ON PILES : Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge.
-
-
-
Initial test (Test Load 2.5 times the Safe capacity)
1
-
-
Routine test (Test Load 1.5 times the Safe capacity)
2
-
-
ANTITERMITE
-
-
-
Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
852
-
-
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar
184.01
-
-
Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres
4850
-
-
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30
1460.63
-
-
WBM; Supplying and stacking at site.
-
-
-
90 mm to 45 mm size stone aggregate
363.75
-
-
63 mm to 45 mm size stone aggregate
363.75
-
-
53 mm to 22.4 mm size stone aggregate
363.75
-
-
Stone screening 13.2 mm nominal size (Type A)
327.38
-
-
Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .
1091.25
-
-
Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.
-
-
-
60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.
4925
-
-
80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.
4850
-
-
NON SCHEDULE ITEMS (quotation to be attached), carpet flooring
-
-
-
Material cost of flotex flocked textile floor covering of nylon 6.6 face fiber or equivalent of approved make with 100% nylon and completely water proof resilient backing. The flooring should be anti-static weight of 1.8 kg/sqm of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sqm. The floor covering should have fire test EN-13501, appearance retention hexapod ISO 140-8, friction slip resistance text EN 14041 class DS, sanitized anti-microbial treatment with resilient water proof backing anti-allergic which is certified by british allergy foundation with ten year replacement guarantee
900
-
-
Wall Panelling ; SITC of wall panelling with required framework structure finished with 19mm W/P plywood and 1mm laminates of desired shade with complete finished.
450
-
-
Wall paper ; wall paper in diffferent shade and design with complete finishand pasting ar per direction.
150
-
-
water cascade
-
-
-
Supplying of Water Transfer Pump 2 hp. (Kirlosker,Texmo, CG ) (1 working, 1 standby
2
-
-
Supplying of LED Light 28 watts with driver.
6
-
-
Supplying, providing of stainless steel stand 304 grade.
6
-
-
Supplying providing sheet water fall S S frame (3 feet each)
3
-
-
Cost of Electrical wire ,casing ,electrical panel for Pump & Light operation.(Havels, Finolex, Polycab)
1
-
-
PHOMI
-
-
-
MCM A series brick 308317 phomi
383.9
-
-
singals of roof
8.64
-
-
SANITARY AND PLUMBING
-
-
-
EUROPEAN TYPE WATER CLOSET:Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid
33
-
-
WASH BASIN:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap
28
-
-
SINK:Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board610x510 mm bowl depth 200 mm
5
-
-
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.
6
-
-
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.
10
-
-
Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.
6
-
-
WASTE COUPLING
-
-
-
Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms
28
-
-
CI PIPES and FITTINGS:Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 :100 mm dia pipe
248
-
-
Providing and laying flanged C.I. standard specials such as tees, bends, collars, tapers, caps etc., suitable for flanged jointing as per IS : 1538 :Up to 300 mm dia
40
-
-
Providing flanged joints to double flanged C.I./ D.I. pipes and specials, including testing of joints :100 mm diameter pipe
638
-
-
SOAK PIT:Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
4
-
-
GI PIPES:Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.External work,50 mm dia nominal bore
350
-
-
Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :25 to 40 mm nominal bore
135
-
-
BIB COCK:Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore
35
-
-
STOP COCK:Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore
29
-
-
BORING : Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. All types of soil. 200 mm dia
130
-
-
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge, 100 mm nominal size dia
120
-
-
Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.
12
-
-
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 100 mm dia
1
-
-
Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 100 mm clamp
1
-
-
Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.(SUCTION PIPES), 50 mm dia nominal bore
120
-
-
LANDSCAPING AND BEAUTIFICATION : Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly,as per direction of officer in charge
715
-
-
Providing and Displaying Bismarckia Palm 115 to 180 cm ht., well developed 12 and above good color fresh and healthy leaves in 40 cm Cement Pot as per direction of the officer-in-charge
45
-
-
Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.
155
-
-
NON SCHEDULE ITEMS : Construction of FRP pergola ( Width = 3.6 m, Height of the side posts = 3.6 m, Height at the apex = 2.8 m) with angle iron of size 50 mm x 50 mm x 5 mm (placing at 2000 mm apart ) embedding the iron posts in P.C.C. base ( not less than 600 mm) covering at the top and sides by chain link fencing, painting one coat of primer and two coats of paint including supplying and planting of flowering climbers as enclosed from both sides ( 3 nos. per metre in one side ) of the pergola to facilitate climbing by pit making (30 cm x 30 cm x 30 cm) filling the pit with the mixture of soil and organic manure and necessary maintenance by trimming etc complete as specified and directed by the department. (P.C.C. and soling to be measured and paid separately)
1
-
-
construction of Dr. Bhupen Hazarika's life size Broonze Statue size 30 feet high incuding pedastal at Kalatirtha with all finish and as per direction.
1
-
-
wall mural with assamse traditional art on boundary wall and srcupture for heritage garden with complete finish and as per direction.( Quototions included)
1
-
-
For Fountain : 8 feet height & 15 feet long Water Cascade with all civil, sanitary, electrical works includding all fitting and finish with complete inatallation.as per direction .
1
-
-
children playing equipments .Children playing items like Play System, Rope play, Slide, Merry Go round, See Saw, Climber, Spring Rider etc as approve and Direction by the authrity with complete inallation and fibish.
11
-
-
seating benches : Appex Timeless Bench 3 seater of stainless steel make with complete finish and inatallation at site as per direction.
11
-
-
dustbin : PVC make with animal shape size 2feet x 4 feet as per direction and approval from authority.
11
-
-
EXTERNAL ELECTRIFICATION : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
12
-
-
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
12
-
-
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
240
-
-
Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.
480
-
-
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
2
-
-
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)
80
-
-
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)
120
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as require
-
-
-
Above 35 sq. mm and upto 95 sq. mm
100
-
-
Above 95 sq. mm and upto 185 sq. mm
200
-
-
Above 185 sq. mm and upto 400 sq. mm
200
-
-
Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.
-
-
-
Above 35 sq. mm and upto 95 sq. mm
200
-
-
Above 95 sq. mm and upto 185 sq. mm
200
-
-
Above 185 sq. mm and upto 400 sq. mm
200
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required
-
-
-
Above 35 sq. mm and upto 95 sq. mm
80
-
-
Above 95 sq. mm and upto 185 sq. mm
140
-
-
Above 185 sq. mm and upto 400 sq. mm
50
-
-
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.
-
-
-
Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)
70
-
-
Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)
50
-
-
Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)
20
-
-
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.
-
-
-
Upto 35 sq. mm (clamped with 1mm thick saddle)
100
-
-
Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)
150
-
-
Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)
100
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
-
-
-
3½ X 35 sq. mm (32mm)
16
-
-
3½ X 50 sq. mm (35mm)
24
-
-
3½ X 70 sq. mm (38mm)
24
-
-
3½ X 95 sq. mm (45mm)
24
-
-
3½ X 120 sq. mm (45mm)
16
-
-
3½ X 150 sq. mm (50mm)
24
-
-
3½ X 185 sq. mm (57mm)
16
-
-
Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
-
-
-
3½ X 35 sq. mm
8
-
-
3½ X 50 sq. mm
12
-
-
3½ X 70 sq. mm
12
-
-
3½ X 95 sq. mm
12
-
-
3½ X 120 sq. mm
8
-
-
3½ X 150 sq. mm
12
-
-
3½ X 185 sq. mm
8
-
-
Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 200 mm width X 50 mm depth X 1.6 mm thickness.
200
-
-
Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.
-
-
-
Above 6.5 metre and upto 8.0 metre(For stret light)
17
-
-
Above 8.0 metre and upto 10.0 metre(For LT line)
8
-
-
Above 10.00 metre and upto 12.00 metre(For transformer and HT line)
4
-
-
Providing and making steel pole collar with cement concrete (1 cement : 3 coarse sand : 6 stone aggregate 20mm) of specified size and shape including form work, plastering if required, curing etc as required. (volume of pole/ pipe not to be deducted)
29
-
-
Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required. 32 mm dia
40
-
-
Supplying and erection of stay set complete (galvanised) with 19/20 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm, thimble, stay clamps, turn buckle ( 20 mm X 60 cm ), 7/ 4.00 mm dia G.I. stay wire and strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required.
2
-
-
Supplying of channel iron 75 mm X 40 mm X 6 mm (7.14 kg per metre) cross arm for 4 wire over head line complete with clamps, bolts, nuts and washer etc including drilling of holes for insulator pins etc (as per drawing) and painting with primer and finished paint as required .
8
-
-
Erection of angle iron/ channel iron cross arm on wood/ RCC/ PCC/ steel tubular/ rail pole etc. as required.
16
-
-
Supplying and erection of galvanised 'D' iron clamps complete with shackle insulator (100 mm X 110 mm), G.I. bolts, nuts and washers, coach screws etc. as required.
12
-
-
Supplying and erection of 100 mm X 80 mm pin insulator complete with G. I. Spindle and nuts etc. as required .
24
-
-
Erection of ACSR conductor of 7/3.35 mm to 7/4.00 diameter and above including binding etc. as required.
1200
-
-
Erection of G.I. Wire No. 8 SWG including binding etc. as required.
300
-
-
Erection of cradle guard as required.
12
-
-
Supplying and erection of 30 A aerial fuse complete as required.
4
-
-
Erection of aerial fuse as required.
4
-
-
Supplying and fixing MV horn gap lightning arrestor as required.
3
-
-
Fixing of MV lightning arrestor as required.
10
-
-
Providing and fixing 50 mm dia X 3.2 metres G.I. pipe (including accessories) complete with 50 mm X 50 mm X 6 mm angle iron bracket on wall and 75 mm X 90 mm shackle insulator with straps for house service connection including painting the angle and flat iron with primer and finish paint etc. as required.
8
-
-
Providing and fixing 50 mm dia X 5.6 metres G.I. pipe (including accessories) complete with 50 mm X 50 mm X 6 mm angle iron cross arm and 40 mm X 3mm M.S. flat iron clamps bends for guard wire, 75 mm X 90 mm shackle insulator and straps, 7/ 3.15 mm G.I. wire stay set for house service connection including painting the angle and flat iron with primer and finish paint etc. as required.
10
-
-
Supplying and erection of galvanised stay set for 11 KV over head lines complete with 19/ 20 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm thick, thimble, stay clamps, turn buckle ( 20 mm X 600 mm ), 7/ 4.00 mm dia G.I. stay wire and 11 KV strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required.
4
-
-
Supplying of channel iron 75 mm X 40 mm X 6 mm (7.14 kg per metre) pole top bracket/ cross arm for single 11 KV over head line conductor complete with 50 mm X 6mm flat iron clamp, bolts, nuts and washers including drilling holes for insulator pins, bolts and nuts etc and painting with primer and finish paint as required.
10
-
-
Supplying of 50 mm X 8 mm M.S. flat iron pole top bracket/ cross arm for single 11/22/33 KV over head line conductor complete with fixing clamps, bolts, nuts and washers drilling holes for insulator pins, bolts and nuts etc and painting with primer and finish paint as required.
8
-
-
Supplying of two lengths of channel iron 75 mm X 40 mm X 6 mm (7.14 kg per metre) double pole cross arm for three wire 11KV over head line conductors complete with through bolts and nuts for clamping to the poles, 50 mm X 6 mm M.S. flats welded on one side to the channel iron and with bolts and nuts on the other side for tying the cross arms together, including drilling holes for insulator pins/ fittings, bolts, nuts and washers etc (as per drawing) and painting with primer and finish paint as required.
4
-
-
Supplying and erection of a set of cross bracing frame work for 11 KV over head line double pole structure having four members fabricated out of 50 mm X 50 mm X 6 mm angle iron to form a rectangle of minimum size 1400 mm width X 2500 mm height , complete with 50 mm X 6mm M.S. flat iron clamps, bolts and nuts including drilling holes for insulator pins, bolts and nuts etc (as per drawing) and painting with primer and finish paint as required.
4
-
-
Erection of double pole 3 wire cross arm for 11KV/ 22KV/ 33 KV over head lines as required.
6
-
-
Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required.
24
-
-
Supplying and erection of 11 KV disc insulator for 11 KV over head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as required.
12
-
-
Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.
3
-
-
Providing and laying in position cement concrete 1:3:6 (1 cement : 2 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required.(includes Transformer foundation also).
80
-
-
Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required
-
-
-
50 mm dia
100
-
-
80 mm dia
150
-
-
100 mm dia
100
-
-
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
480
-
-
Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.
-
-
-
125 Amp, 36KA, FPMCCB
4
-
-
400 Amp, 50KA, FPMCCB
2
-
-
800 Amp, 50 KA, TPMCCB
2
-
-
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) , 2 + 12 way, Double door
4
-
-
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator), 6 way (4 + 18), Double door
2
-
-
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
-
-
-
Single pole
110
-
-
Double pole
8
-
-
Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps
2
-
-
Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.
8
-
-
Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32amps 415 volts "C" curve TP MCB complete with connections, testing and commissioning etc. as required.
4
-
-
Supply, installation, testing and commissioning of LED post of lantern 28W with inbuilt driver metal heat sink with double sided connection, IP66/IK10 with symmetric light distribution.
20
-
-
Supply,fitting, fixing etc. of 72W LED(NEXUS NEO LED) street light made of pressure die cast Aluminium Housing with toughened glass and high power LEDs and secondary lenses with IP66 .System efficiency=110LPW. Option for 3000K 10KV SPD included. Crompton or equivalent make.(LSTP-72-CDL-M)
15
-
-
Supply of sky cove LED strip light including Driver in pack(24W output) available in 3000K and 6500K Philips or equivalent make.(LED strip sky cove 5M WW with driver).
300
-
-
Supply, installation, testing and commissioning of 9W LED Bollard light(City Cube Bollard D) with inbuilt driver metal heat sink with double sided connection, IP65/IK10 with base plate
10
-
-
Supply of 200W LED flood light made of pressure die cast Aluminium Housing with toughened glass and high power LEDs and secondary lenses with IP66 .System efficiency=110LPW. Option for 3000K 10KV SPD included. Crompton or equivalent make.(LFLN-200-CDL/60-M)
8
-
-
Supplying of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 650/1100 V grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required.
-
-
-
i)3 X 6 sq.mm
2500
-
-
ii)3 ½ X 35 sq.mm
150
-
-
iii)3 ½ X 70 sq.mm
150
-
-
iv)3 ½ X 150 sq.mm
200
-
-
v)3 ½ X 300 sq.mm
70
-
-
Supplying of following sizes XLPE insulated,insulation screening with extruded semi conducting compound in combination with copper tape cores laid up inner sheath of PVC tape,galvanised flat steel strip armoured and overall PVC sheathed cable confirming to IS7098(Part-II) 1985 with latest amendments . i)3C,95sq.mm HT Cable.
40
-
-
Supplying of following sizes GI pole confirming to IS: 2713.
-
-
-
i)7 Mtr(SP-3) For street light.
15
-
-
ii)9 Mtr(SP-33) For LT line.
8
-
-
iii)12 Mtr(SP-66) For HT line.
4
-
-
Supplying and drawing of 11KV overhead high tension line through Racoon conductor on the existing pole struture with necessary binder, pin, cross arm etc. as required complete.
300
-
-
Supply ,installation, testing and commissioning of 500 KVA (4 STAR/BIS LEVEL 2), NO LOAD VOLTAGE RATIO (KV) : 11/0.433 kV NUMBER OF PHASES 3, TYPE OF COOLING : ONAN FREQUENCY(C/S) : 50 C/S, VECTOR GROUP : DY n11 CONNECTION : DELTA/STAR TAPPINGS ON HV FOR HV VARITION : 5 POINTS TEMPERATURE RISE IN OIL (degree C) : 35ºC TEMPERATURE RISE IN WINDINGS (degree) : 40ºC MAXIMUM AMBIENT TEMP.(degree C) : AS PER IS 1180(Part1)2014 SERVICE : OUTDOOR MATERIAL OF WINDING : COPPER, QUATITY OFFERED : AS REQUERED, TERMINAL ARRANGEMENT : a) High Voltage Side : Bushing b) Low voltage Side : Bushing (Covered), complete including the payment to be made to power supply authority for supervision charge, labour charge, cost of L.T/H.T metering etc. (excluding the cost of load security) and making necessary arrangement for charging approval of the sub-station from the competent authority as directed and specified by the department. Transformer should be as per CEA guidelines as ammended up to date upto 200 KVA star rating up to 5 star, above 200KVA as per CEA guidelines for losses along with LV enclosure.
1
-
-
Supplying, erection, testing and commissioning of 16 M high mast system with its accessories.Mast shaft shall be hot dip galvanised and suitable for wind velocity as per IS 875, it shall also include accessories of HighMast accessories for High Mast including headframe, steel wire rope 6mm dia.(7/19 construction), trailing cable,double drum winch, galvanise lantern carriage arrangement suitable arrangement for light symmetrically and lighting finial. The mast shall have an integral power tools installed inside the base compartment for its operation lumunaire with wiring materials, 8 Nos. of 200W LED flood light and supply of foundation bolts manufactured from special steel alongwith nut and bolts, washer, anchore plate and templates etc
3
-
-
Suppy, Installation, Tesing and commissining of 250 KVA "KIRLOSKAR" make diesel Engine 6SL1500TA G3 liquid cooled turbo charged with after cooler, developing 310HP 6 cylinder, inline type, electric start, compression ignition, 4 stroke designed to run continously 1500 RPM confirming to IS 10001 ISO-3046, BS-5514 standard with an overload capacity of 10% for one hour in every 12 Hrs.Diesel Engine will comply with present CPCB-II norms and will be directly coupled to a KIRLOSKAR(KOEL GREEN) A.C Generator capable of developing 250KVA/200KW. KOEL GREEN make alternator is suitable for continous operation rated at 1500 RPM, 415V,0.8PF ,50Hz, 3Ph in SPDP enclosure, self excited and self regulated, brush -less, floor mounted with ball or bearings on end shields.The Alternator efficiency is as per IS 4722 & IEC 34-1 standards and will be suitable for tropical condition.(Genset Model-6SL1500TAG3,KVA=250,HP=310,KW=200,PHASE=3).
1
-
-
Supplying including installation, connection as approved by the Deptt., testing and commissioning of SUBMERSIBLE PUMP SET 3 (Three Phase) 3 HP with steel cable rope and submersible cable complete as directed and specified by the deptt.
1
-
-
Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical indoor type floor/wall mounting compartmentalize panel board of size 2.00M(B)X 1.70M(H) X 0.40M(D) made of 16 SWG (1.66 mm) thick C.R. sheet and 40mm X 40mm X 5mm size angle having 4 nos legs at the bottom. The panel board is to be errected in 1 : 3 : 6 PCC foundation including brick soling / grouting etc. complete neatly wiring done with provision for one no 800A 4pole MCCB or Switch Fuse Unit as incomer and provision for 8nos DP or TPN out going as specified and directed by the deptt. confirming to IP 43 protection comprising of the following electrical items: 1. i) 50mm X 10mm 4 strip copper Bus - Bar 3.10 M length each ii) 30mm X 5mm 4 strip copper Bus-Bar 0.6M each 8 sets , 2. Poilt Lamp with integral ckt LED 110- 230 V (Red,Yellow,& Blue) - 3 nos 3. Voltmeter & Ammeter Selector Switch - 2 nos, 4. 2 A Slide fuse unit - 3nos
-
-
-
(Incoming & Outgoing Switch Gear of reqd. rating along with Meters will be measured and paid separately)
1
-
-
Payment to be made to the local APDCL authority for Load security,meter security etc.
300
-
-
INTERNAL ELECTRIFICATION : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B
818
-
-
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
4
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
-
-
-
2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
1090
-
-
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
10325
-
-
2 X 4 sq. mm + 1 X 4 sq. mm earth wire
1200
-
-
2 X 6 sq. mm + 1 X 6 sq. mm earth wire
784
-
-
4 X 10 sq. mm + 2 X 6 sq. mm earth wire
180
-
-
4 X 16 sq. mm + 2 X 6 sq. mm earth wire
300
-
-
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required
200
-
-
Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 100mmx100mmx60mm deep
122
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required
-
-
-
5/6 A switch
1008
-
-
2 way 5/6 A switch
4
-
-
15/16 A switch
58
-
-
3 pin 5/6 A socket
164
-
-
6 pin15/16 A socket
58
-
-
TV antenna socket outlet
4
-
-
Bell push
2
-
-
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required
128
-
-
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
62
-
-
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required
-
-
-
3 Module (100mmX75mm)
114
-
-
4 Module (125mmX75mm)
58
-
-
6 Module (200mmX75mm)
44
-
-
12 Module (200mmX150mm
48
-
-
Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.
-
-
-
3 Module
114
-
-
4 Module
58
-
-
6 Module
44
-
-
12 Module
48
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required
52
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
33
-
-
Supplying and fixing brass batten/ angle holder including connection etc. as required.
18
-
-
Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.
2
-
-
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door
5
-
-
Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.63 Amp TP&N
8
-
-
Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.
-
-
-
250 Amp, 35 KA, TPMCCB
2
-
-
400 Amp, 35 KA, TPMCCB
1
-
-
Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)
-
-
-
4 way (4 + 12), Double door
4
-
-
8 way (4 + 24), Double door
4
-
-
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
-
-
-
Single pole
234
-
-
Double pole
7
-
-
Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A
11
-
-
Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63A
10
-
-
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
12
-
-
Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
230
-
-
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
5
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 35 sq. mm and upto 95 sq. mm
120
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X95 sq. mm (45mm)
8
-
-
Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 95 sq. mm
8
-
-
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) . 12 way , Double door
2
-
-
Providing and fixing lighting conductor finial made of 25mm dia.300mm long GI tube having single prong at the top with 85mm dia. 6mm thick GI base plate including making hole etc as required complete.
2
-
-
Installation,testing and commissioning of prewired fluorescent fitting compact fluorescent fitting of all types complete with all accesssories and tube/lamp etc. directly on ceiling/wall, including connection with 1.5sqmm FRLS PVC insulated,copper conductor, single core cable and earthing etc as required.
606
-
-
Installation,testing and commissioning of ceiling fan, including wiring the down rods of standard length(upto 30cm) with 1.5sqmm FRLS PVC insulated,copper conductor, single core cable and earthing including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
124
-
-
Numbering of ceiling fan/exhaust fan/fluorescent fitting as required.
200
-
-
Installation of exhaust fan in the existing opening, including making good the damages,connection,testing and commissining etc. as required. Upto 450mm sweep.
28
-
-
Supply of wall/ceiling mounting 20W LED polycarbonate tube with inbuilt driver metal heat sink with double sided connection. Crompton or equivalent make.(LT8-20-865(2).
79
-
-
Supply of recessed mounting LED down light suitable for any modern workspace with robust Aluminium housing and 5700K, 4000K,3000K CCT Efficacy 100LM/W. Crompton or equivalent make.(CDR-204-06-57-SL-NWH).
163
-
-
Supply of surface mounting 18W round LED down light suitable for any modern workspace with PDC Aluminium housing high transluscent frosted plastic diffuser, Efficacy 100LM/W. Crompton or equivalent make.(LCDSPLN-R-18-WW).
420
-
-
Supply of Endura LED Bulkhead (Pressure diecast housing) with IP66 protection and IK09 impact resistance suitable for surface and wall mounting applications. Philips or equivalent make.(WT202W LED 6S NW PSU S2 PC).
16
-
-
Supplying including installation, testing and commissioning of 2.00Tr capacity inverter type Split air conditioner (Code No.4502972, 5 star adjustable,Voltas SAC 245V ADZ(R32)
33
-
-
Supplying including installation, testing and commissioning of 5 KVA ,Voltage stabilizer with with working range 90V AC (VD5090B).
33
-
-
Supply of energy efficient Ceiling fan 1200 mm sweep (Make- USHA : Model Name :Energia 32 5 star in the existing arrangement.
120
-
-
Supply of 250mm sweep, 900rpm non metalic exhaust fan in the existing hole of the buildintg, Ventil air DX/DX-HS whitef(Havels make,
22
-
-
Supply of power cables,solid Aluminium conductor upto10sqmm balance stranded conductor,XLPE insulated, core laid up, PVC tape/Extruded innersheathed for multicore cables, Armoured(Aluminium wire for single core upto 70sqmm balance Aluminium strip, Galvanised wire for cables upto 2x10sqmm, 4X6 sqmm balanced all galvanised steel strip),extruded PVC type ST2 sheathed, 650/1100V grade as per IS 7098(Part-I) 1988. 3&1/2 core ,95sqmm cable.
50
-
-
Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical indoor type floor/wall mounting compartmentalize panel board of size 0.90M(B)X 1.25M(H) X 0.40M(D) made of 16 SWG (1.66 mm) thick C.R. sheet and 35mm X 35mm X 5mm size angle having 4 nos legs at the bottom. The panel board is to be errected in 1 : 3 : 6 PCC foundation including brick soling / grouting etc. complete neatly wiring done with provision for one no 400A 4pole MCCB or Switch Fuse Unit as incomer and provision for 8nos DP or TPN out going as specified and directed by the deptt. confirming to IP 43 protection comprising of the following electrical items: 1. i) 40mm X 5mm 4 strip copper Bus - Bar 1.20 M length each ii) 20mm X 3mm 4 strip copper Bus-Bar 0.5M each 4 sets, 2. Poilt Lamp with integral ckt LED 110- 230 V (Red,Yellow,& Blue) - 3 nos, 3. Voltmeter & Ammeter Selector Switch - 2 nos, 4. 2 A Slide fuse unit - 3nos, (Incoming & Outgoing Switch Gear of reqd. rating along with Meters will be measured and paid separately)
1
-
-
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
-
-
-
Single pole
16
-
-
Double pole
2
-
-
Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A
2
-
-
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
3
-
-
Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
80
-
-
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
3
-
-
Installation,testing and commissioning of prewired fluorescent fitting compact fluorescent fitting of all types complete with all accesssories and tube/lamp etc. directly on ceiling/wall, including connection with 1.5sqmm FRLS PVC insulated,copper conductor, single core cable and earthing etc as required.
24
-
-
Installation,testing and commissioning of ceiling fan, including wiring the down rods of standard length(upto 30cm) with 1.5sqmm FRLS PVC insulated,copper conductor, single core cable and earthing including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
4
-
-
Numbering of ceiling fan/exhaust fan/fluorescent fitting as required.
30
-
-
AIR HANDLING UNIT Supply, installing, testing and commissioning of factory built draw through type Floor Mounted/Ceiling Suspended double skin type air handling units. Double skinned panels shall be 40 mm thick and shall be made of 0.8mm Pre-coated GSS on outside and 0.6mm Galvanized sheet inside of 275 GSM coating with CFC – FREE P.U. insulation of 42 (+/- 5%) kg/Cu M density injected in between and an internal gasket between the skins to interrupt the thermal bridge of the panel. Mixing box with control damper for fresh air, return air and exhaust air. Blower section with AMCA certified DIDW for ceiling suspended unit and direct driven plug fan for floor mounted unit with highly efficient IE3 TEFC Squirrel cage motor drive suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply and variable frequency drive (VFD) and suitable for static pressure as required, Dx-Cooling coil of required row deep with aluminium finned, copper tubes (tubes thickness not less than 0.4mm) cooling coil, stainless steel (18G) drain pan with drain connections. Filter section with 50mm thick washable synthetic type air prefilters having efficiency 90% down to 10 micron. Necessary vibration isolation arrangement, canvas connection etc., complete as per specifications and of followings capacities.
-
-
-
Floor Mounted AHU :16000 CFM (40 TR) 6 Row deep coil, 50 mm static pressure
2
-
-
Floor Mounted AHU : 7000 CFM (17 TR) 4 Row deep coil, 40 mm static pressure
1
-
-
AIR HANDLING UNIT KIT: Supply, installation, testing and commissioning of Electronic expansion valve & control kit compatible to connect the following Dx type AHU with the VRF outdoor unit, the AHU kit should be complete with Control box, control the flow of refrigerant so as to modulate the capacity of AHU as and when required in sync with VRF outdoor unit, the AHU kit should have corded remote control, and capability to control the AHU fan on/off operation, speed of AHU Fan.
-
-
-
AHU :(40.0 TR)
2
-
-
AHU :(17.0 TR)
1
-
-
Y-JOINTS: Supply Installation, testing and commissioning of supply and return refrigerant piping Y-joints sets as per manufacturer standards. Y Joints set as per Drawing
23
-
-
REFRIGERANT PIPING: Supply Installation, testing and commissioning of Interconnecting refrigerant copper pipe work (between indoor and outdoor units as per specifications) with (19mm/13mm thick) closed cell elastomeric nitrile rubber tubular insulation. All piping inside the room shall be properly supported with MS slotted angle, including cutting chases, holes in walls/slabs and making them good. All external piping shall run in covered cable tray (item for cable tray shall be quote seperately).
-
-
-
Dia 6.4 mm pipe with 13mm thick insulation
65
-
-
Dia 9.5 mm pipe with 13mm thick insulation
160
-
-
Dia 12.7 mm pipe with 13mm thick insulation
140
-
-
Dia 15.9 mm pipe with 19mm thick insulation
135
-
-
Dia 19.1 mm pipe with 19mm thick insulation
305
-
-
Dia 22.2 mm pipe with 19mm thick insulation
85
-
-
Dia 25.4 mm pipe with 19mm thick insulation
40
-
-
Dia 28.6 mm pipe with 19mm thick insulation
170
-
-
Dia 34.9 mm pipe with 19mm thick insulation
60
-
-
Dia 41.3 mm pipe with 19mm thick insulation
235
-
-
Providing and fixing of PVC drain pipe of 6 Kg /cm2 pressure rating complete with 9mm thick closed cell nitrile rubber insulation, fittings, supports, valves as per specifications and drawings.
-
-
-
25 mm dia OD
135
-
-
32 mm dia OD
125
-
-
50 mm dia OD
25
-
-
FACTORY FABRICATED GSS DUCTING: Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows/ bends, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.
-
-
-
Thickness 0.63 mm sheet (24 G)
900
-
-
Thickness 0.80 mm sheet (22 G)
340
-
-
Thickness 1.00 mm sheet (20 G)
30
-
-
Thickness 1.25 mm sheet (18 G)
25
-
-
SITE FABRICATED GSS DUCTING: Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.
-
-
-
Thickness 0.63 mm sheet (24 G)
80
-
-
Thickness 0.80 mm sheet (22 G)
50
-
-
Thickness 1.00 mm sheet (20 G)
10
-
-
Thickness 1.25 mm sheet (18 G)
10
-
-
AIR TERMINALS:Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets,nuts, bolts, screws linkages, flanges etc., as per specifications.
5
-
-
Supplying and fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.
25
-
-
Supplying and fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.
250
-
-
Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring and removable core.
20
-
-
Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring and removable core.
20
-
-
Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt echanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.
-
-
-
Fire Damper
7
-
-
Actuator
10
-
-
ACOUSTIC LINING OF DUCTS:Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.
200
-
-
THERMAL INSULATION:Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.19 mm
1250
-
-
Supplying, fabricating, installing and testing of fire retardent double Canvas Flexible Connection for constructed of standard material as per the drawings/specifications.
15
-
-
Design, fabrication, supply, installation, testing and commissioning of LT Panel / Sub-distribution panels fabricated out of 2mm thick for structural members and 1.6mm thick for door and covers CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system and lifting hooks shall also be provided in case of large panels. Degree of ingress protection of IP-54. VRF ODU PANEL, In comer (1 No.): 500A, 4 pole MCCB (15 KA) Metering: 0-500 Volts, digital Voltmeter and shall be protected by 2Amps MCBs. 0-500Amps digital Ammeter and 500/5A, 10VA, CL-1 CTs and selector switch. Phase indicating lamps and shall be protected by 2Amps MCBs. Bus Bars: 625Amps TP Aluminium busbars, colour coded with heat shrinkable insulation sleeves. OutGoings : (2) Nos. 4 pole 40A MCCB , (1) Nos. 4 pole 63A MCB, (5) Nos. 4 pole 100A MCB (1 No. Spare )
1
-
-
CABLE WORKS: Supply laying and fixing copper conductor XLPE insulated armoured FRLS PVC Sheathed UG Cable of 1.1 kv grade conforming to IS7098(P-I) with cable tray/on surface/recess in between main supply & outdoor unit etc. as required.
-
-
-
4cx 10 sqmm
40
-
-
4cx 16 sqmm
40
-
-
4cx 35 sqmm
60
-
-
Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.
-
-
-
2 x 1.5 sq. mm
1450
-
-
3 x 2.5 sq. mm
100
-
-
CABLE TRAY:Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.
-
-
-
100 mm x 50 mm x 1.6 mm thickness
50
-
-
150 mm x 50 mm x 1.6 mm thickness
60
-
-
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm Dia
1500
-
-
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
51.75
-
-
Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.
56.7
-
-
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar
191.75
-
-
Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.
1425.1
-
-
Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: G.S. Sheet
126
-
-
Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area beyond 3 sq. metres
22
-
-
Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.
180
-
-
FIREFIGHTING : external hydrent system: SITC of end suction centrifugal type main fire pump (electrical driven) connected to TEFC induction motor suitable for 3ph, 440V, 50 Hz AC supply for hydrant main / sprinkler main system with cast iron casing & bronze impeller complete with coupling guard necessary base frame, foundation bolts complete as required (refer approved make list in special condition) (Wilo/Lubi/KBL) a. Discharge : 1650 LPM, b. Head : 70 mtr ,c. RPM : 2900, d. Mover : Electric Motor Driven.
1
-
-
SITC of end suction centrifugal type main fire pump (diesel engine driven) with cast iron casing & bronze impeller, complete with coupling, coupling guard necessary base frame, foundation bolts complete with suitable diesel engine of speed matching the pump speed with battery & battery charger, integration of engine controller with electrical panel for automatic start, necessary wiring, fuel tank exhaust system complete as required (refer approved make list in special condition) (CGL/Wilo/Lubi/KBL), a. Discharge : 1650 LPM, b. Head : 70 mtr, c. Mover : Diesel Engine, d. Fuel Tank : 150 Ltr, e. Accessories : AVM pads, Mounting frame
1
-
-
Supply, installation of MS heavy duty exhaust pipe of 100 mm NB with insualtaion with proper supports, fittings, accessories etc.
6
-
-
SITC of end suction centrifugal type Jockey fire pump (electrical driven) connected to TEFC induction motor suitable for 3 ph, 440V, 50 Hz AC supply for hydrant main / sprinkler main system with cast iron casing & bronze impeller complete with coupling, coupling guard necessary base frame, foundation bolts complete as required (refer approved make list in special condition)(Wilo/Lubi/KBL), a. Discharge : 180 LPM, b. Head : 70 mtr, c. RPM : 2900, d. Mover : Electric Motor Driven.
1
-
-
Erection for delivery header of size 200X150X150X80 mm dia for fire pump.
1
-
-
Design, manufacturing, SITC of following Main Electrical Fire control panels suitable for 415V, 3 phase, 4 wire, 50 Hz power distribution system, the panel should be indoor, free standing, floor mounted, sheet metal clading with thickness as specifies in technical specification, cubicle, dust and vermin proof conforming to IP-54 enclosure, compartmentalized complete with AI busbars, seperate earth bus bar, adequate size cable alley, painting, earting numbering, etc. as required as per specifications and drawings. (Make:- Agni Suraksha), INCOMING : a. One -250 AMP, TP M.C.C.B 25KA service breaking capacity with heavy duly neutral link, b. One - Volt Meter (0-500V) with Selector Switch, c. One Set - Indicating Lamps, BUS BARS : a. 250 A TPN Bus Bar (Alluminium), OUTGOING : a. Two - 200 AMP, T.P M.C.CB, 25KA service breaking capacity with heavy duly neutral link. b. Two - 100 AMP, T.P M.C.C.B, 25KA service breaking capacity with heavy duly neutral link. c. Two fully Automatic Star - Delta Starter suitable for Main Pump Motor with over load Relay, Timer Push Buttons and Auto / Manual Selector Switch. d. One fully Automatic D.O.L Starter suitable for Jocket Pump Motor with over load Relay, Timer, Push buttons and Auto/Manual Selector Switch.e. Four - Phase Indicating Lamps.f. Three - Panels Type AMP, Meters, One for each Motor with ASS, CTS etc.g. Three - Neon indicating Lamps, one for each other.FOR DIESEL ENGINE MAIN PUMP a. 20 Amps DPMCB - 1 Nos b. Battery charger with transformer with rectifier resistance DC ammeter, DC voltmeter, Trickle / booster / off selector switch. c. Indicating Lamps - 1 set for the following : Phase indicator, battery on, DG supply on, engine fails to start, Pump on. c. Auto manual selector switch - 1 set, d. Push button - 1 set for the following, Engine start, Engine stop, Engine - Fault reset, Engine fault acknowledge, e. Selector switches (Engine control, mode selector) - 1 No. f. Auxiliary relays / contactors /timer for sequence operating for starting and stopping of the engine - 1 set. g. Hooter for audio alarm (industrial type) - 1 No. All the components shall be housed in a common cubical made of M.S sheet with both bottom & top cable entry provisions.
1
-
-
Providing and fixing of 4 way Gun Metal fire brigade collecting suction head with instantaneous female coupling with 150mm dia. MS suction pipe and foot valve complete as required.
1
-
-
SITC of 'c' class MS Pipe as per IS : 1239 like clamping, hanging, bracketing from supporting structure with heavy metal clamp as required, jointing with flange/weds for elbows, reducers, plugs, Tees, bends, etc. including painting with two coats of approved enamel paint over a coat of approved primer etc. complete as required. (All Civil works of owner's scope),
-
-
-
a. 150 mm (Over Ground with Painting)
28
-
-
c. 80 mm
12
-
-
Providing, installing, testing & commissioning of C.I body Foot Valves for Fire Pumps. (Make:- KVMC/BIR/KARTAR)
-
-
-
a. 150 mm
2
-
-
c. 80 mm
1
-
-
Supply and installation testing and commissioning of CI Butterfly Valves (heavy) conforming to BS 5155 to 1.5 times working pressure with necessary flanges, bolts, nuts, gasket packing, support, indicator for open and shut position complete as required (Audco/Advance/Leader)
-
-
-
a. Size : 150 mm
3
-
-
b. Size : 100 mm
1
-
-
c. Size : 80 mm
2
-
-
SITC of NRV conforming to IS 5312 (Dual Plate Check type) with CI body & brass trim part, having necessary flangers, Gaskets, arrow indicating direction of flow complete as required. (Advance/Leader/Kartar)
-
-
-
a. Size : 150 mm
3
-
-
b. Size : 100 mm
1
-
-
c. Size : 80 mm
1
-
-
Supply, installation testing and commissioning pressure switch assembly with interlocking of pumps. (refer approved make list in special condition), Pressure Switch (0-10 kg/sq. cm)
3
-
-
SITC of 100 mm dial Pressure gauge with Syphon tubing, isolation valve & mounting accessories complete Range: 0 -10kg/sq.cm (refer approved make list in special condition)Pressure Gauge : 0-16 kg/sq.cm
5
-
-
Supply & fixing of Ball Valve with fittings screw end type complete (refer approved make list in special condition)
-
-
-
a. 15 mm dia
5
-
-
b. 25 mm dia
5
-
-
Supply of following size XLPE insulated PVC sheathed armoured power cable of grade 1.1 KV, aluminium conductor of following size. Confirming to relevant IS code (7098, part - I, 1985) complete as required at site (refer approved make list in special condition)
-
-
-
a. 3C X 16Sq. MM. AL. PVC Armoured Cable (JOCKEY PUMP)
30
-
-
b. 3 C X 95 Sq. MM. AL. XLPE ARM Cable (Fire Panel to Main Pump)
30
-
-
c. 12C X 2.5 Sq. MM. Cu. PVC Armoured Cable (Control Cable.)
15
-
-
d. 2C X 2.5 Sq. MM. Cu. PVC Armoured Cable (Control Cable.)
40
-
-
Supply and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required (refer approved make list in special condition)
-
-
-
a. 3 C X 16 Sq. MM. Cu. PVC Armoured Cable (Jockey Pump)
2
-
-
b. 3 C X 95 Sq. MM. AL. XLPE ARM Cable (Fire Panel to Hydrant & Sprinkler)
4
-
-
c. 12C X 2.5 Sq. MM. Cu. PVC Armoured Cable (Control Cable.)
2
-
-
d. 2C X 1.5 Sq. MM. Cu. PVC Armoured Cable (Control Cable.)
14
-
-
Laying of one number PVC insulated and PVC sheathed / xlpe power cable of 1.1 KV grade of following size on wall surface.
-
-
-
a. Upto 35 sqmm
90
-
-
b. Above 35 sqmm and upto 95 sqmm
35
-
-
Supplying & fixing SS single headed External hydrant valves with instantaneous SS couplings of 63mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type - A) with blank gun metal cap and chain as required.
7
-
-
Providing of short standard 63mm dia SS Branch pipe as per IS Code complete with fixing clips
7
-
-
Providing 63 mm dia 15m long fungus resistant reiforced rubber lined hose pipe marked to IS :636 Type A with SS male & female coupling wire wound with the hose pipe.
14
-
-
Providing & fixing Steel Hose cabinet (of size 750mmx250mmx450mm) made of 18 gauge thick MS sheet with 6mm thick glazed glass doors i/c necessary locking arrangement suitable to accommodate external hydrant with 2nos 15m long hoses and one no branch pipe. The cabinet shall be painted with red colour shade No. 536 of IS :5 complete as per direction of Engineer in charge.
7
-
-
Providing and fixing of 2 way Gun Metal fire brigade Inlet collection head with instantaneous female coupling with 100mm dia. complete as required.
1
-
-
Supply and fixing first aid fire hose reel drum wall mounting, swinging type fitted with 25 mm dia ms pipe connection with Jyoti or equivalent make 20mmx30mtr rubber hose with 5 mm outlet ABS nozzle.( Make:- ISI )
3
-
-
sprinkler in auditorium : SITC of 'c' class MS Pipe as per IS : 1239 like clamping, hanging, bracketing from supporting structure with heavy metal clamp as required, jointing with flange/weds for elbows, reducers, plugs, Tees, bends, etc. including painting with two coats of approved enamel paint over a coat of approved primer etc. complete as required. (All Civil works of owner's scope)
-
-
-
a. 150 mm (Under Ground with Wrapping Coating)
12
-
-
b. 100 mm (Over Ground with Painting)
18
-
-
c. 80 mm
96
-
-
d. 50 mm
132
-
-
e. 40 mm
132
-
-
f. 32 mm
198
-
-
d. 25 mm
143
-
-
Supply & fixing of 68* Pendent type Sprinkler Valve with fittings screw end type complete (refer approved make list in special condition)
210
-
-
SITC of 100 mm dial Pressure gauge with Syphon tubing, isolation valve & mounting accessories complete Range: 0 -10kg/sq.cm (refer approved make list in special condition), Pressure Gauge : 0-16 kg/sq.cm
3
-
-
Supply & fixing of Ball Valve with fittings screw end type complete (refer approved make list in special condition)
-
-
-
a. 15 mm dia
3
-
-
b. 25 mm dia
8
-
-
Supply and installation testing and commissioning of CI Butterfly Valves (heavy) conforming to BS 5155 to 1.5 times working pressure with necessary flanges, bolts, nuts, gasket packing, support, indicator for open and shut position complete as required (Audco/Advance/Leader)
-
-
-
a. Size : 150 mm
1
-
-
b. Size : 100 mm
3
-
-
fire alarm and detection systemSupply, Installation, Testing and Commissioning of Analogue Addressable optical smoke detector with built-in fault isolator, having open digital protocol, alarm flag for fast alarm reporting, alarm address for fast location of alarm, red LED alarm indication clear during quiescent state, operating temperature -20 ̊C to + 60 ̊C, humidity 0 - 95% RH( non condensing), digital protocol for error free transmission, unique address mechanism for data storage in the base to ensure high reliability all as per specifications etc as required.
18
-
-
Supply, Installation, Testing and Commissioning of Analogue Addressable rate of rise type Heat detector with built-in fault isolator, having open digital protocol, alarm flag for fast alarm reporting, alarm address for fast location of alarm, red LED alarm indication clear during quiescent state, operating temperature -20 ̊C to + 60 ̊C, humidity 0 - 95% RH( non condensing), digital protocol for error free transmission, unique address mechanism for data storage in the base to ensure high reliability all as per specifications etc as required.
8
-
-
Supply, Installation, Testing and Commissioning of Analogue Addressable Beam detector with built-in fault isolator, having open digital protocol, alarm flag for fast alarm reporting, alarm address for fast location of alarm, red LED alarm indication clear during quiescent state, operating temperature -20 ̊C to + 60 ̊C, humidity 0 - 95% RH( non condensing), digital protocol for error free transmission, unique address mechanism for data storage in the base to ensure high reliability all as per specifications etc as required.
2
-
-
Supply, Installation, Testing and Commissioning of Analogue Addressable loop sounders having continuous or pulsed tone, having output power of 85-dB A at 1 meter, digital protocol compatible, etc as required.
4
-
-
Supply, Installation, Testing and Commissioning of Analogue Addressable Pull Down type Manual Call Point suitable for reporting its addresses, interrupting the loop and producing alarm in less than 0.2 seconds, complete with RED LED as alarm indicator etc as required.
4
-
-
Supply, installation, testing and commissioning of Analog Addressable Single Input Monitor Modules complete in all respect.
2
-
-
Supply, Installation,Testing and Commissioning of Response Indicator etc as required.
8
-
-
Supply, installation, testing & commissioning of Micro processor based 2 wire fault tolerant loop, networkable type, fire alarm/detection control panel. The panel shall be able to give location of all fire/fault conditions of addressable units via the address codes. Further, the panel must be able to automatically switch ON /OFF respective control module when ever any alarm is triggered. The panel shall have rectifier, Loop cards, minimum 80 character L C D unit to indicate Fire/Fault Signal with address and analog output, external/inbuilt printer to log all fire or fault events complete in all respects.The Panel Shall housed in a Powder coated CRC enclusure selaed to IP30. The Panel Shall have 20 Zones with Individual LED Indicators, expandable to 80 LED Indicators. The Panel Shall have 3 Serial Ports. The panel shall have a built in power supply and battery charger along with maintenance free 24 AH, 2 x 12 volt SMF Lead acid batteries capable of running for a minimum of 24 hours with battery charger complete as required and as per specifications conforming to BS5839 Standards and Duly Approved by EN54/LPCB/VDS.
1
-
-
Supply & fixing of Emergency Exit Light with battery back up & Battery charger.
6
-
-
Supplying, drawing, connecting, testing & commissioning of 2 core x 1.5 sq. mm. multi stranded copper conductor, pvc insulated PVC sheathed, unarmoured cable suitable for Fire Alarm System.
900
-
-
ACOUSTIC : Supply and Installation of Anutone Subtex Nubby,steppe edge, Glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having volume density 120Kgs/m3, weight 1.8/ 2.4kg/m2 which is suspended by using 0.3mm thick Anutone Skelet TrelisT15 metal grid system.
-
-
-
Anutone Skelet TrelisT15 metal grid system of 600x600mm module includes Anutone Skelet WA15W30 wall angle with unequal flanges of 15/19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Anutone Skelet MT15W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Anutone Skelet CT15W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally Anutone Skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600x600mm module. Anutone Subtex Nubby steppe edge of size 595x595x15/20mm shall be placed into the grid size of 600x600mm. En :sure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. Optional: The system is backlined with the acoustical infill Anutone SynthPF 5x25 Technical Parameters : • Fire (Class) – 1 & P
• Acoustics – NRC 0.9 (For E900 Mounting)
• Thermal conductivity (W/mk)– 0.066
• Climate (°C, RH) – 40, 95
• Light reflectance (%) – 85
• Green (VoC, RC %) – Low, 35
372
-
-
Supply & installation of Anutone Sircle Circulo made of pinewood E1 grade fiberboard, with big circle perforations of 50mm dia, melamine laminated finish, 1-test fire retardant grade, size 595x1195x12mm, Conceil A Edge, volume density of base board 800Kg/m3, weight 8.8Kgs/m2 which is suspended by using 0.3mm thick and 24mm wide Anutone Skelet TrelisT24 Conceal A framework
-
-
-
Anutone Skelet TrelisT24 Conceal A framework system of 600x1200mm module includes Anutone Skelet WA24W30 wall angle with equal flanges of 24mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Anutone Skelet MT24W36 MainT with flange width 24mm, height 38mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 600mm centres. Anutone Spacer bar with pre notched slots (Anutone Skelet WA24W30 wall angle) at 600mm centers in staggered pattern are placed above Main T24 to hold system in position. Anutone Sircle Circulo Conceil A edge of size 595x1195x16mm shall then be slided onto MT24. Optional: The system is backlined with Anutone SynthPF 5x25. Technical Parameters • Fire (Class) – 1 & P (For FR grade)
• Acoustics – NRC upto 0.85
• Thermal conductivity (W/mk)– na
• Climate (°C, RH) – 40, 70
• Light reflectance (%) – Colour Dependant
• Green (VOC, RC %) – Low, 25
121
-
-
Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine/veneer laminated finish, groove perforated slats L16-2 - (2mm Slats @16mm pitch) / L32-2 - (2mm grooves @ 32mm centers), backlined with Soundtexblack acoustical fleece, tongue-groove edge for a seamless look, 1-test fire retardant grade, size 128x2440x16mm, volume density of base board 800Kg/m3, weight 8Kgs/m2 (L16), 10.5Kgs/m2 (L32), installed by using Anutone Strut framework system.
-
-
-
Anutone Strut framework system includes Anutone Strut CC10 aluminium core cross channel having thickness 0.55mm, length 3600mm, knurled web 40mm, depth 10mm and equal flanges 15mm is fastened to wall or framework behind vertically/horizontally at every 600mm c/c. Anutone Strut CC18 aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge ¢re brackets is then fixed perpendicular to the Strut CC10 Cross channel with the help of fasteners at every 400mm centers. Slats Surco of size 128x 2440x16mm in then fixed perpendicular to CC18 with suitable edge & centre brackets. Short edges of the panel are staggered. Contractor to provide expansion joints of 3mm at every 4.88m length wise and 4.992m width wise. Panels are backlined with Anutone SynthPF 10x25 held in position with dab spots of Anutone Stick S7. Technical Parameters : • Fire (Class) – 1 & P (For FR grade)
• Acoustics – NRC 0.77 (For E300* Mounting)
• Thermal conductivity (W/mk)– na
• Climate (°C, RH) – 50, 70
• Light reflectance (%) – 75 (Maple Arce)
• Green (VOC, RC %) – Low, 25
130
-
-
Supply and installation of Anutone Stretch Decor Grafix system consisting of FR Grade Hush fabric-based membrane with high-performance integrated core andacoustically-transparent face covering of choice colour, size 1.4mx75m, stretched by using combination of Anutone Strut CC10 Cross Channel and Anutone Strut FS15 Tracks, Anutone Strand, 10mm woodenbase, Anutone SynthPF 5x10 infill with requisite accessories. The Anutone Strut system includes Anutone Strut CC10 Cross Channel, fully knurled, sectional thickness 0.55mm, length 3600mm, web 40, depth 10mm and equal flanges of 15mm is fastened to the wall @ 600mm centers. Woodenbase 10mm is then installed on the CC10 along the marking lines with metal fasteners at 300mm centers. FS15 tracks to be installed on wooden base, by first applying Stick S7 adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Anutone Strut Tracks. Strand square edge magnesite bonded pinewood fiber panels of size 600x1200x20mm having density 400kg/m3, weight 8kg which is fixed to Strut CC10 Cross Channel inbetween tracks. Long edge of panels should be perpendicular to length of Strut CC10 Cross Channel. SynthPF 5x10mm adhered on Strand by using Stick 7 adhesive.
-
-
-
The Anutone Stretch Decor Grafix acoustical membrane of width 1.4m is stretched and tucked into the Anutone Strut Tracks and secured to the locking jaws with purpose-specific tucking tools to obtain smooth, taut, wrinkle-free finish. Ensure the weft and weave of the fabric along with the surface are all oriented in one direction to achieve uniform shade. The Decor Grafix fabric should be printed with digital immage selected by Architect or engineer in charge as per direction. Note: Minimum 100mm additional fabric is required for tucking hence maximum module wall fabric width would be 1300mm. Technical Parameters of fabric : • Fire (Class) – 1 & P
• Acoustics – na
• Thermal conductivity (W/mk)– na
• Climate (°C, RH) – 49, 90
• Light reflectance (%) – Colour Dependant
• Green (VoC, RC %) – Low, 25 Technical Parameters of Strand : • Fire (Class) – 1 & P
• Acoustics – NRC 0.97 (For 40mm C50 Mounting)
• Thermal conductivity (W/mk)– 0.07
• Climate (°C, RH) – 50, 95
• Light reflectance (%) – 80
• Green (VoC, RC %) – Low, 30
296
-
-
Supply and Installation of Anutone Subtex Nubby,steppe edge, Glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having volume density 120Kgs/m3, weight 1.8/ 2.4kg/m2 which is suspended by using 0.3mm thick Anutone Skelet TrelisT15 metal grid system.
-
-
-
Anutone Skelet TrelisT15 metal grid system of 600x600mm module includes Anutone Skelet WA15W30 wall angle with unequal flanges of 15/19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Anutone Skelet MT15W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Anutone Skelet CT15W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally Anutone Skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600x600mm module. Anutone Subtex Nubby steppe edge of size 595x595x15/20mm shall be placed into the grid size of 600x600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. Optional: The system is backlined with the acoustical infill Anutone SynthPF 5x25, Technical Parameters • Fire (Class) – 1 & P
• Acoustics – NRC 0.9 (For E900 Mounting)
• Thermal conductivity (W/mk)– 0.066
• Climate (°C, RH) – 40, 95
• Light reflectance (%) – 85
• Green (VoC, RC %) – Low, 35
250
-
-
Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine/veneer laminated finish, groove perforated slats L16-2 - (2mm Slats @16mm pitch) / L32-2 - (2mm grooves @ 32mm centers), backlined with Soundtexblack acoustical fleece, tongue-groove edge for a seamless look, 1-test fire retardant grade, size 128x2440x16mm, volume density of base board 800Kg/m3, weight 8Kgs/m2 (L16), 10.5Kgs/m2 (L32), installed by using Anutone Strut framework system.
-
-
-
Anutone Strut framework system includes Anutone Strut CC10 aluminium core cross channel having thickness 0.55mm, length 3600mm, knurled web 40mm, depth 10mm and equal flanges 15mm is fastened to wall or framework behind vertically/horizontally at every 600mm c/c. Anutone Strut CC18 aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge ¢re brackets is then fixed perpendicular to the Strut CC10 Cross channel with the help of fasteners at every 400mm centers. Slats Surco of size 128x 2440x16mm in then fixed perpendicular to CC18 with suitable edge & centre brackets. Short edges of the panel are staggered. Contractor to provide expansion joints of 3mm at every 4.88m length wise and 4.992m width wise. Panels are backlined with Anutone SynthPF 10x25 held in position with dab spots of Anutone Stick S7, Technical Parameters : • Fire (Class) – 1 & P (For FR grade)
• Acoustics – NRC 0.77 (For E300* Mounting)
• Thermal conductivity (W/mk)– na
• Climate (°C, RH) – 50, 70
• Light reflectance (%) – 75 (Maple Arce)
• Green (VOC, RC %) – Low, 25
146
-
-
Supply and installation of Anutone Stretch Decor Grafix system consisting of FR Grade Hush fabric-based membrane with high-performance integrated core andacoustically-transparent face covering of choice colour, size 1.4mx75m, stretched by using combination of Anutone Strut CC10 Cross Channel and Anutone Strut FS15 Tracks, Anutone Strand, 10mm woodenbase, Anutone SynthPF 5x10 infill with requisite accessories. The Anutone Strut system includes Anutone Strut CC10 Cross Channel, fully knurled, sectional thickness 0.55mm, length 3600mm, web 40, depth 10mm and equal flanges of 15mm is fastened to the wall @ 600mm centers. Woodenbase 10mm is then installed on the CC10 along the marking lines with metal fasteners at 300mm centers. FS15 tracks to be installed on wooden base, by first applying Stick S7 adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Anutone Strut Tracks.
-
-
-
Strand square edge magnesite bonded pinewood fiber panels of size 600x1200x20mm having density 400kg/m3, weight 8kg which is fixed to Strut CC10 Cross Channel inbetween tracks. Long edge of panels should be perpendicular to length of Strut CC10 Cross Channel. SynthPF 5x10mm adhered on Strand by using Stick 7 adhesive. The Anutone Stretch Decor Grafix acoustical membrane of width 1.4m is stretched and tucked into the Anutone Strut Tracks and secured to the locking jaws with purpose-specific tucking tools to obtain smooth, taut, wrinkle-free finish. Ensure the weft and weave of the fabric along with the surface are all oriented in one direction to achieve uniform shade. The Decor Grafix fabric should be printed with digital immage selected by Architect or engineer in charge as per direction. Technical Parameters of fabric : • Fire (Class) – 1 & P
• Acoustics – na
• Thermal conductivity (W/mk)– na
• Climate (°C, RH) – 49, 90
• Light reflectance (%) – Colour Dependant
• Green (VoC, RC %) – Low, 25 Technical Parameters of Strand : • Fire (Class) – 1 & P
• Acoustics – NRC 0.97 (For 40mm C50 Mounting)
• Thermal conductivity (W/mk)– 0.07
• Climate (°C, RH) – 50, 95
• Light reflectance (%) – 80
• Green (VoC, RC %) – Low, 30
350
-
-
Supply and Installation of Anutone SUBTEX EBONEY (Black Color), square edge, Glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having volume density 120Kgs/m3, weight 1.8kg/m2 which is suspended by using 0.3mm thick Anutone Skelet TrelisT15 metal grid system. Technical Parameters • Fire (Class) – 1 & P
• Acoustics – NRC 0.9 (For E900 Mounting)
• Thermal conductivity (W/mk)– 0.066
• Climate (°C, RH) – 40, 95
• Light reflectance (%) – 85
• Green (VoC, RC %) – Low, 35
30
-
-
Supply and Installation of Anutone SUBTEX NUBBY (White Color), square edge, Glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having volume density 120Kgs/m3, weight 1.8kg/m2 which is suspended by using 0.3mm thick Anutone Skelet TrelisT15 metal grid system. Technical Parameters • Fire (Class) – 1 & P
• Acoustics – NRC 0.9 (For E900 Mounting)
• Thermal conductivity (W/mk)– 0.066
• Climate (°C, RH) – 40, 95
• Light reflectance (%) – 85
• Green (VoC, RC %) – Low, 35
210
-
-
Supply and Installation of Anutone Strand Ebony, Kerfed edge Magnesite bonded pinewood fibre core tiles of size 600x2400x20, density 400 kgs/m3, weight 8kg/m2 installed by using Anutone Strut framework system with non-visible fasteners using Anutone Strut H-Spline. Technical Parameters • Fire (Class) – 1 & P
• Acoustics – NRC 0.87 (For 15mm thk C50 Mounting)
• Thermal conductivity (W/mk)– 0.08
• Climate (°C, RH) – 50, 90
• Light reflectance (%) – Low light reflectivity
• Green (VOC, RC %) – Low, 30
64
-
-
Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine/veneer laminated finish, groove perforated slats L16-2 - (2mm Slats @16mm pitch) / L32-2 - (2mm grooves @ 32mm centers), backlined with Soundtexblack acoustical fleece, tongue-groove edge for a seamless look,Non FR, size 128x2440x16mm, volume density of base board 800Kg/m3, weight 8Kgs/m2 (L16), 10.5Kgs/m2 (L32), 11Kgs/m2 (L64) installed by using Anutone Strut framework system. Technical Parameters • Acoustics – NRC 0.77 (For E300* Mounting)
• Thermal conductivity (W/mk)– na
• Climate (°C, RH) – 50, 70
• Light reflectance (%) – 75 (Maple Arce)
• Green (VOC, RC %) – Low, 25
94
-
-
Supply and installation of Anutone Stretch Decor Grafix system consisting of FR Grade Hush fabric-based membrane with high-performance integrated core andacoustically-transparent face covering of choice colour, size 1.4mx75m, stretched by using combination of Anutone Strut CC10 Cross Channel and Anutone Strut FS15 Tracks, Anutone Strand, 10mm woodenbase, Anutone SynthPF 5x10 infill with requisite accessories. Strand square edge magnesite bonded pinewood fiber panels of size 600x1200x20mm having density 400kg/m3, weight 8kg which is fixed to Strut CC10 Cross Channel inbetween tracks. Long edge of panels should be perpendicular to length of Strut CC10 Cross Channel. SynthPF 5x10mm adhered on Strand by using Stick 7 adhesive. The Anutone Stretch Decor Grafix acoustical membrane of width 1.4m is stretched and tucked into the Anutone Strut Tracks and secured to the locking jaws with purpose-specific tucking tools to obtain smooth, taut, wrinkle-free finish. Ensure the weft and weave of the fabric along with the surface are all oriented in one direction to achieve uniform shade. The Decor Grafix fabric should be printed with digital immage selected by Architect or engineer in charge as per direction. Note: Minimum 100mm additional fabric is required for tucking hence maximum module wall fabric width would be 1300mm TECHNICAL PARAMETERS (FABRIC) • Fire (Class) – 1 & P
• Acoustics – na
• Thermal conductivity (W/mk)– na
• Climate (°C, RH) – 49, 90
• Light reflectance (%) – Colour Dependant
• Green (VoC, RC %) – Low, 25
115
-
-
FURNITURE Construction of Premium Conference Table finished with Veneer at the Top as per the instruction the Engineer in Charge.
1
-
-
Supplying and placing ergonomically designed, comfortable & aesthetically appealing High back chair. The seat shall be made of 15mm thick hot pressed curved plywood upholstered with high resilience polyurethane foam 50mm thick having density 40kg/m³ with khaki leatherite tapestry 0.8mm thick and 535 GSM and the back shall be supported by metal insert MS CRCA frame upholstered with high resilience polyurethane foam 12mm thick having density 23kg/m³ with khaki leatherite tapestry 0.8mm thick and 535 GSM with contoured lumbar support which helps to provide full back support and maintain the natural curvature of the spine. Headrest shall be provided for comfort of head with leatherite tapestry. The armrest shall be used MS CRCA chrome plated with PU arm completely joint with seat and back. The chair shall have knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 100mm with BIFMA standard class-3 gaslift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal shall be made up of MS CRCA chrome plated having pitch circle Dia 640 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with BIFMA standards. The Seat size shall be 485±10 mm(W)X520±10 mm(D) and back size shall be 740±10 mm(H) from seat, overall height = 1150±10 mm and overall depth/width= 740±10mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
2
-
-
Providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be supplied with inserted pipe frame. The chair shall be padded with high resilience polyurethane foam 50mm thick having density 40Kg/m³ in seat and 12mm thick having density 23Kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM and breathable mesh tapestry behind the backrest. MS chrome plated pipe frame shall be provided on both side of seat and back with size 25mm X 10mm. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support. The armrest shall be used black integral polyurethane arm mounted on CRCA chrome plated pipe having size 40mm X 10mm completely joint with seat and back with the assistance of Allen key screw. A chrome plated round bend pipe of dia. 9mm shall be provided behind the backrest of the chair and welded with main frame. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal shall have five legged CRCA chrome plated having pitch circle dia. 650mm fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled, confirming to ANSI/BIFMA Standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The Seat size shall be 490±10 mm(W) X 520±10 mm(D) and back size shall be 450±10 mm(W) X 535±10 mm(H) from seat & overall height = 980±10 mm, overall width = 560±10 mm & overall depth = 670±10 mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
40
-
-
Construction of Premium Conference Table finished with Veneer at the Top as per the instruction the Engineer in Charge.
1
-
-
Supplying and placing ergonomically designed, comfortable & aesthetically appealing High back chair. The seat shall be made of 15mm thick hot pressed curved plywood upholstered with high resilience polyurethane foam 50mm thick having density 40kg/m³ with khaki leatherite tapestry 0.8mm thick and 535 GSM and the back shall be supported by metal insert MS CRCA frame upholstered with high resilience polyurethane foam 12mm thick having density 23kg/m³ with khaki leatherite tapestry 0.8mm thick and 535 GSM with contoured lumbar support which helps to provide full back support and maintain the natural curvature of the spine. Headrest shall be provided for comfort of head with leatherite tapestry. The armrest shall be used MS CRCA chrome plated with PU arm completely joint with seat and back. The chair shall have knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 100mm with BIFMA standard class-3 gaslift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal shall be made up of MS CRCA chrome plated having pitch circle Dia 640 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with BIFMA standards. The Seat size shall be 485±10 mm(W)X520±10 mm(D) and back size shall be 740±10 mm(H) from seat, overall height = 1150±10 mm and overall depth/width= 740±10mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
2
-
-
Providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be supplied with inserted pipe frame. The chair shall be padded with high resilience polyurethane foam 50mm thick having density 40Kg/m³ in seat and 12mm thick having density 23Kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM and breathable mesh tapestry behind the backrest. MS chrome plated pipe frame shall be provided on both side of seat and back with size 25mm X 10mm. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support. The armrest shall be used black integral polyurethane arm mounted on CRCA chrome plated pipe having size 40mm X 10mm completely joint with seat and back with the assistance of Allen key screw. A chrome plated round bend pipe of dia. 9mm shall be provided behind the backrest of the chair and welded with main frame. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal shall have five legged CRCA chrome plated having pitch circle dia. 650mm fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled, confirming to ANSI/BIFMA Standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The Seat size shall be 490±10 mm(W) X 520±10 mm(D) and back size shall be 450±10 mm(W) X 535±10 mm(H) from seat & overall height = 980±10 mm, overall width = 560±10 mm & overall depth = 670±10 mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
200
-
-
Supplying and placing a three seater sofa that shall be constructed from metal insert PU Moulded Seat and back. The complete structure shall be upholstered with leatherite tapestry 1±0.2 mm thick. The understructure shall have SS pipe frame having dia 50mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The individual seat size shall be 550±10 mm(W) X 440±10 mm (D) X 420±10 mm (H). Overall width = 1830±10 mm, overall depth = 750±10 mm & overall height = 750±10 mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
10
-
-
Supplying & placing center table with an overall size 1200mm X 600mm X 450mm. The top shall be made up of 30mm thick Pre-laminated particle board of grade II of IS 12823. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The lower shelf shall be made up of 18mm thick Pre-laminated particle board. The under structure shall consist of SS 202 grade shiny chrome finish pipe frame having cross-section area 30mm X 15mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
5
-
-
Supplying & placing cafe table with an overall size 900mm x 900mm x 750mm. The top of the table shall be made up of 20mm thick granite rock. The top profile shall be in square shape and the edges shall be in round shape. The top shall be supported on 11mm thick ply-board having size 750mm X 750mm and SS 202 grade pipe frame having cross-section area 40mm X 20mm with 1.6mm thick in X shape. The table under structure shall be made up of SS grade 202 base pole leg having Dia. 63.5mm. The base shall be in X shape with SS pipe frame having cross-section area 40mm X 40mm. There shall be leveler shoe provided with metal insert at the base to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
12
-
-
Supplying & Placing Cafe Chair. The seat shall be made of 15mm thick hot pressed plywood upholstered with high resilience polyurethane foam 19mm thick having density 40kg/m³ with black leatherite tapestry 0.8mm thick and 535 GSM and the back shall be made of metal frame upholstered with high resiliance polyurethane foam 12mm thick having density 23kg/m³ with black leatherite tapestry 0.8mm thick and 535 GSM. The seat and back shall be fixed with plywood & metal frame. The frame structure shall be supported by four legs made up of SS with shiny chrome finish square pipe of size 20mm X 20mm with 1.6mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The Seat size shall be 410±10 mm(D)X430±10 mm(W) and back size shall be 420±10 mm(W)X400±10 mm(Ht) from seat. Overall height shall be = 860±10 mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
48
-
-
Supplying and placing executive table in knock down condition with an overall size 1350mm X 750mm X 750mm that is to be assembled at site. The worktop shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. The top shall be supported on MS/CRCA rectangle pipe frame having cross-section area 40mm X 20mm with 1.6mm thick. The table understructure shall be supplied with MS round pipe having dia. 25.4mm with 1.6mm thick. 1 nos. footstep shall be provided between both side leg with the same size i.e dia. 25.4mm with 1.6mm thick. Fixed pedestal unit shall be supplied with 3 nos. of drawer at one side. All the drawer shall be synchronized locked with central locking mechanism by one single key. The drawer shall be operated with recessed handle. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.
2
-
-
Providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle Dia. 650±15 mm and fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 460±10 mm(W) X 450±10 mm(D) and back size shall be 460±10 mm(W) X 400±10 mm(H) from seat. Seat height = 460±10 mm, overall height shall be = 810±10 mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
2
-
-
Providing, supplying and placing steel almirah in perfectly upright and straight position. The overall size of the Almirah shall be 915mm (W) X 485mm (D) X 1980mm (H) including legs. It should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. Door shall be made of 1mm thick and all other components shall be made of 0.8mm thick high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. Stiffeners shall be provided in shelf & door. The steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity per each shelf shall be 40kg maximum. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 50-60µ. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
2
-
-
Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and having density 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam thick having density 32Kg/m³. SS strip shall be provided on front of the arm having length 515mm with cross-section area 14mm X 4mm. The structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have shiny chrome finish SS leg with height 100mm and 10mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor.
3 Seater : The seat size shall be 500±10 mm(D) X 1480±10 mm(W), seat height = 430±10 mm, overall width = 1625±10 mm, overall depth = 750±10 mm & overall height = 700±10 mm.
2 Seater : The seat size shall be 500±10 mm(D) X 1015±10 mm(W), seat height = 430±10 mm, overall width = 1160±10 mm, overall depth = 750±10 mm & overall height = 700±10 mm.
Single Seater : The seat size shall be 500±10 mm(D) X 545±10 mm(W), seat height = 430±10 mm, overall width = 690±10 mm, overall depth = 750±10 mm & overall height = 700±10 mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
2
-
-
Supplying & placing center table with an overall size 1200mm X 600mm X 450mm. The top shall be made up of 30mm thick Pre-laminated particle board of grade II of IS 12823. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The lower shelf shall be made up of 18mm thick Pre-laminated particle board. The under structure shall consist of SS 202 grade shiny chrome finish pipe frame having cross-section area 30mm X 15mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
2
-
-
Supplying & placing cafe table with an overall size 900mm x 900mm x 750mm. The top of the table shall be made up of 20mm thick granite rock. The top profile shall be in square shape and the edges shall be in round shape. The top shall be supported on 11mm thick ply-board having size 750mm X 750mm and SS 202 grade pipe frame having cross-section area 40mm X 20mm with 1.6mm thick in X shape. The table under structure shall be made up of SS grade 202 base pole leg having Dia. 63.5mm. The base shall be in X shape with SS pipe frame having cross-section area 40mm X 40mm. There shall be leveler shoe provided with metal insert at the base to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.
2
-
-
Supplying & Placing Cafe Chair. The seat shall be made of 15mm thick hot pressed plywood upholstered with high resilience polyurethane foam 19mm thick having density 40kg/m³ with black leatherite tapestry 0.8mm thick and 535 GSM and the back shall be made of metal frame upholstered with high resiliance polyurethane foam 12mm thick having density 23kg/m³ with black leatherite tapestry 0.8mm thick and 535 GSM. The seat and back shall be fixed with plywood & metal frame. The frame structure shall be supported by four legs made up of SS with shiny chrome finish square pipe of size 20mm X 20mm with 1.6mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The Seat size shall be 410±10 mm(D)X430±10 mm(W) and back size shall be 420±10 mm(W)X400±10 mm(Ht) from seat. Overall height shall be = 860±10 mm. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
6
-
-
Supplying and placing a decorative design bed with an overall size 1560mm (L)X 2060mm (W) X 900mm/400mm. The bed shall be made of Pre-laminated particle board of grade II of IS 12823 with approved laminate colour. The head and leg of the bed shall be made of 18mm thick particle board and also covered by 18mm thick particle board 100mm from edges for aesthetically view. The edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel with the assistance of edge banding machine at 200 degree celsius. The left and right view of the bed shall also be made of 18mm thick particle board with 2mm PVC edge banding at upper side and 0.8mm thick edge banding al bottom side. 18mm thick particle board is used in bed seat. The seat subdivided into two parts for manual openable storage unit at both side i.e. left and right. The bed seat shall be supported on 25mm thick particle board which divide the storage into four ports. The bed shall be supplied with MS CRCA powder coated frame with 1.5mm thick for strength. The bed base shall be used 12mm thick particlde board. There shall be nylon shoe provided at the base to avoid scratches on the floor of maintain uneven surface. Two side unit shall be provided with the bed at both side with an overall size 450mm X 450mm x 550mm. The side unit shall be made of 18mm thick Pre-laminated particle board of grade II of IS 12823. It shall be supplied with one sliding drawer and one open drawer. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.
2
-
-
Supplying and placing ergonomically designed, comfortable & aesthetically appealing Auditorium chair. The seat shall be made of 12mm thick hot pressed plywood with HR polyurethane foam upholstered with fire retardent fabric tapestry and the back shall be made of 15mm Plywood with PU Foam upholstereed 3 layered laminate 5mm thick with fabric tapestry. The Chair shall have a seat sliding mechanism. The armrest shall be made of PP with cup holder. All metal components shall be powder coated in black colour with min 40-60 micron. The grouting plate shall have bolting support. Seat size shall be 470±10mm(W) X 450±10mm(D) and back size shall be 750±10mm (H) from seat X 450±10mm (W) & overall height 1010±10mm.The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015, ISO-45001:2007 and ISO-50001, BIFMA membership since the last 7 years, AIOTA certification, Green Pro certification for some of its products and Greenguard certification from UL USA for some of its products.
100
-
-
AUDIO VISUAL : CONFERENCE HALL : Digital Conference Controller with upto 4 cameras, with inbuilt DAFS ( Digital Acoustic Feedback supression ) with the following features and technical specifications : The Control Unit shall have the following features: Built-in digital recorder with internal memory and USB recording. Built-in loudspeaker and headphone socket for listening to recorded discussions before replaying them to the Floor, or listening to recordings. Built-in Digital Acoustic Feedback Suppression (DAFS). USB connector on front of unit for connecting a USB memory stick. 3.5 mm (0.14 in) stereo headphone socket. Micro USB connector on rear of unit for transferring internal memory (recordings) to a PC. Four additional RCA outputs for individual microphone recording, e.g. for recording individual speakers in a courtroom. Additional capacitive touch buttons and LED indicators for: CU loudspeaker volume (or headphones volume, if connected). Start, Pause (hold), and Stop recording. TECHNICAL SPECIFICATIONS Mains voltage=100 to 240 VAC ± 10% , Current consumption=Maximum 0.6 A (100 VAC) to 0.2 A (240 VAC) , DC supply to Discussion Devices=24 V ± 1 V (current limited), Number of Discussion Devices per Control Unit=Max. 40 devices per trunk connector, Discussion Device loudspeakers volume control=15 steps of 1.5 dB (starting from -10.5 dB), Limit thr,eshold level to unit=12 dB above nominal level, Gain reduction due to number of open microphones (NOM)=1/SQRT (NOM), Sample rate=44.1 kHz, Nominal input (85 db SPL)= 0.5% , Ma, x. input (110 db SPL)= 0.5%, Audio inputs : XLR nominal mic. Input=-56 Dbv, XLR maximum mic. Input=-26 dBV, RCA nominal input=-24 dBV (+/- 6 dB), RCA maximum input=+6 dBV, S/N= 94 dBA, Frequency response=30 Hz to 20 kHz Audio outputs, RCA nominal output=-24 dBV (+6/- 24 dB), RCA maximum output=+6 dBV, S/N= 102 dBA, Frequency response=30 Hz to 20 kHz
1
-
-
Digital Conference Discussion device with the following features and technical specifications , Plug-and-play functionality. Compact, attractive, ergonomic design, with LED indicator in the Discussion Device and in head of microphone. Choice of short or long fixed microphone with flexible stem. Loudspeaker integrated into front of device. Built-in headphone socket with output level control. Automatic level reduction when microphone is activated (configurable via web browser application of Control Unit): prevents acoustic feedback from headphone to microphone. Configurable as a participant or chairperson’s device: changeable microphone buttons and concealed slide switch at the bottom of the device for configuration purposes. GSM immunity. The device shall have the following user controls and indicators: Microphone button. Color-coded LED indicator above microphone button for showing the status of the device: White (‘Possible‑To‑Speak’) shall indicate that the microphone will be active immediately after pressing the microphone button. Green shall indicate that the participant has pressed the microphone button and the request to speak has been added to the waiting list. Green flashing shall indicate that the participant is first in the waiting list, i.e. next in line to speak. Red shall indicate that the microphone is active. Rotary thumbwheel on side of device for adjusting volume of connected headphones. Concealed initialization button at base of device for re-assigning the network address. TECHNICAL SPECIFICATIONS : Frequency response=200 Hz to 12.5 kHz, Headphones load impedance= 32 ohms 1k ohm , Loudspeaker nominal output=72 dB SPL
52
-
-
Extention cables 10 meters: Dimensions (dia.)=6 mm (0.24 in), Material=PVC
12800
-
-
Premium Two Way Wall mounted speakers with following , TECHNICAL SPECIFICATIONS : Maximum power =45 W, Rated power (PHC) =30W, Power tapping=30/15/7.5/3.75 W, Sound pressure level at rated=105/90 dB (SPL), power / 1 W (1 kHz, 1 m), Effective frequency range (-10 dB)=100 Hz to 19 kHz , Opening angle at 1 kHz / 4 kHz=166° / 83° (hor.), 140° / 76 , (-6 dB), Rated input voltage=15.5/70/100 V ,,Rated impedance =8/163/333 ohm, Transducers127 mm (5”) woofer, 13 mm,(0.51”) dome tweeter
10
-
-
1.5 SQMM SPEAKER CABLE ,15 AWG (75/0.16mm) x 2 Core - ATC
300
-
-
240 watts Mixer amplifier with min 4 Audio + 1 BGM Input , USB Input: TECHNICAL SPECIFICATIONS : Frequency response/0 Hz to 20 kHz (+1/‑3 dB @ ‑10 dB ref. rated output), (Line)/6, Frequency response/0 Hz to 20 kHz (+1/‑3 dB @ ‑10 dB ref. rated output), (Mic.), Distortion/, Sound pressure level at ratedpower / 1 W (1 kHz, 1 m)/105/90 dB (SPL), Bass Control/Max. ± 8 Db, Treble Control/Max. ± 8 dB
1
-
-
8 PORT HDMI SWITCH : TECHNICAL SPECIFICATIONS : VIDEO INPUT : Interfaces/8 x HDMI Type A Female (Black), Impedance/100 Ω, Max. Distance/3m @1920X1080@60 (4:4:4), VIDEO INPUT : Interfaces/8 x HDMI Type A Female (Black), Impedance100 Ω, Max. Distance/15m @1920X1080@60 (4:4:4)Max. Data Rate/6.75 Gbps (2.25 Gbps Per Lane), Max. Pixel Clock/225 MHz, Max. Resolution/Up to 1080p.
1
-
-
8 PORT HDMI SP LITTER, : TECHNICAL SPECIFICATIONS : VIDEO INPUT : Interfaces/1 x HDMI Type A Female (Black, Impedance/100 Ω, Max. Distance/5m (at 4K resolution), VIDEO INPUT: Interfaces/1 x HDMI Type A Female (Black, Impedance/100 Ω, Max. Distance/5m (at 4K resolution), Max. Data Rate/10.2 Gbps (3.4 Gbps Per Lane), Max. Pixel Clock/340 MHz, Max. Resolution/Up to 4096 x 2160 / 3840 x 2160 @ 60Hz (4:2:0);4096 x 2160 / 3840 x 2160 @ 30Hz (4:4:4)
1
-
-
HDMI HDBaseT-Lite Extender (4K@40m) (HDBaseT Class B) , TECHNICAL SPECIFICATIONS : VIDEO INPUT: Interfaces/1 x HDMI Type A Female (Black), Impedance/100 Ω, Max. Data Rate/10.2 Gbps (3.4 Gbps Per Lane), Max. Pixel Clock/340 MHz, Max. Resolution/DistanceUp to 4K@35m (Cat 5e/6) / 40m (Cat 6a/ATEN 2L-2910 Cat6);1080p@60m (Cat 5e/6) / 70m (Cat 6a/ATEN 2L-2910 Cat6), *4K supported:4096 x 2160 / 3840 x 2160 @ 60Hz (4:2:0);4096 x 2160 / 3840 x 2160 @ 30Hz (4:4:4),
16
-
-
HDMI Repeater Plus Audio De-embedder: TECHNICAL SPECIFICATIONS : VIDEO INPUT : Interfaces/1 x HDMI Type A Female (Black), Impedance/100 Ω, Max. Distance/3m at 1920*1080@60 (4:4:4), VIDEO INPUT, Interfaces/1 x HDMI Type A Female (Black), Impedance/100 Ω, Max. Distance/3m at 1920*1080@60 (4:4:4), Max. Data Rate/6.75 Gps (2.25 Gbps Per Lane), Max. Pixel Clock/225 MHz, Max. Resolution/Up to 1920 x 1080, AUDIO INPUT/1 x HDMI Type A Female (Black); Output/1 x Toslink (Black);1 x RCA (Orange);2 x RCA (Red/White);
1
-
-
1 METER HDMI CABLE, TECHNICAL SPECIFICATIONS : Max. Video Resolution, Cable Outer Dimension /6.0 ± 0.15mm, Conductor Gauge/30AWG, Conductor Material/Tinned Copper, Connector PlatingGold, Connector Type/HDMI (19pin) Male to Male, Cable Shield Type/Aluminum Foil, Cable Jacket Type/PVC
40
-
-
4 PORT INPUT/OUTPUT HDMI MATRIX SWITCHER : TECHNICAL SPECIFICATIONS : VIDEO INPUT : Interfaces/'4 x HDMI Type A Female (Black), Impedance/100 Ω, Max. Distance/5m (at 4K resolution), VIDEO OUTPUT/4 x HDMI Type A Female (Black), Interfaces/'4 x HDMI Type A Female (Black), Impedance10m (at 4K resolution), Max. Distance10.2 Gbps (3.4 Gbps Per Lane), Max. Data Rate10.2 Gbps (3.4 Gbps Per Lane), Max. Pixel Clock340 MHz, Max. ResolutionUp to 4096 x 2160 / 3840 x 2160 @ 60Hz (4:2:0)4096 x 2160 / 3840 x 2160 @ 30Hz (4:4:4)
1
-
-
CODEC FOR VIDEO CONFERENCING : Communication Method/SIP, H.323, Video Compression Method/H.261 (mainstream only), H.263, H263+, H.263++ (reception only), H.264 High Profile, H.264 Baseline Profile, Audio Compression Method/G.711 μ-law, A-law (3.4 kHz@64 kbps)G.722 (7.0 kHz@64 kbps)G.722.1 (7.0 kHz@32 kbps)G.722.1 Annex C (14.0 kHz@48 kbps/24 kbps)MPEG-4 AAC-LD Mono (7.0 kHz@32 kbps, 14.0 kHz@64 kbps, 22.0 kHz@96 kbps)MPEG-4 AAC-LD Stereo (14.0 kHz@64 kbps, 22.0 kHz@96 kbps), No. of Channels/G.711/G.722/G.722.1/G.722.1 Annex C: 1MPEG-4 AAC-LD Mono: 1/ MPEG-4 AAC-LD Stereo: 2, Remote Camera Controi/H.224, H.281 (Zoom/Pan/Tilt/Preset), Dual Stream/H.239 (H.323), BFCP (SIP), Method/2 displays*1, No. of Applicable Resolution Frames/Main: Max. 1080 p 30 frames/second, Sub: Max. 1080 p 30 frames/second, Encryption/SRTP (AES 128 bit), H.235 (AES 128 bit), Communication Bandwidth/256 kbps to 18 Mbps, Video/176 x 144 p, 352 x 240 p, 352 x 288 p, 512 x 288 p, 640 x 480 p, 704 x 480 p, 704 x 576 p, 768 x 432 p, 800 x 600 p, 1024 x 768 p, 1280 x 720 p, 1280 x 768 p, 1280 x 800 p, 1920 x 1080 p, Max. 60 frames/second (When using H.264 1080 p), Full-screen, Picture in Picture, Picture with Picture, Side by Side, AudioEcho canceller, Auto gain control, Stationary noise reduction, Lip synch, Equalizer, Mic mute, I/O Terminals, Video InputHDMI main x 1, HDMI sub x 1, Input resolution: 1280 x 720 p, 1920 x 1080 i, 1920 x 1080 p, RGB x 1 (Mini D-sub 15 pin), HDMI x 1*3, Input compatible resolution: VGA, SVGA, XGA, HD, WXGA, SXGA, FWXGA, WXGA+, WXGA++, UXGA, WSXGA+, Full-HD, Video Output/HDMI x 2*1, Boundary Omnidirectional Microphone (Digital Interface Type) x 1 (KX-VCA001X) Max. 4, Boundary Omnidirectional Microphone (Analogue Interface Type) x 1 (KX-VCA002X) Max. 1, HDMI, Stereo mini-plug*4 x 1 (ø0.35 cm), RCA (Stereo) x 1, Audio OutputHDMI*5, Stereo mini-plug*4 x 1 (ø0.35 cm), RCA x 1 (Stereo), Network/RJ45 x 1, 1000BASE-T/100BASE-TX/10BASE-T Full Duplex, No. of Simultaneous Connection Sites/4 (Default), Network Protocol/TCP/IPv4, TCP/IPv6, UDP/IPv4, UDP/IPv6, DHCP, DNS, HTTP, HTTPS, TELNET, NTP, Network Functions/t resending (ARQ), Forward Error Correction (FEC), Adaptive Rate Control (ARC), Reorder, Packet Shaping, Arbitrary Port Setting, NAT Compatibility, Encryption, IP Precedence/DiffServ Support, External Control/Control via web browser/HTTP CGI, TELNET, RS-232C, Connection ModesIP mode, NAT Traversal Service, IP/NAT Traversal Service.
1
-
-
PTZ VIDEO CONFERENCING CAMERA : SPECIFICATIONS: Effective Pixels/1920 x 1080p: Pan / Tilt/Pan: ±130°, Tilt: ＋90°-25, Zoom (optical/digital)/12x / 10x, Angle of view (optical zoom)/Horizontal angle of view 72.5 º (Wide end) - 6.3º (Tele end), F1.8 (Wide end) - F2.8 (Tele end), Presets/12 positions, Connection Cable/HDMI
1
-
-
SOFTWARE LICENSE FOR VIDEO CONFERENCE
1
-
-
Windows i7
1
-
-
Screen Size: 85" Brightness (cd/m²): Typ. 620 / Peak 850 Native contrast ratio: 4,000:1 Dynamic contrast ratio: 600000:1 Display resolution (H x V, pixels): 3,840 x 2,160 HDR (High Dynamic Range) compatiblity: Yes (HDR10,HLG,Dolby Vision)
1
-
-
Screen Size: 75" Brightness (cd/m²): Typ. 620 / Peak 850 Native contrast ratio: 6,000:1 Dynamic contrast ratio: 600000:1 Display resolution (H x V, pixels): 3,840 x 2,160 HDR (High Dynamic Range) compatiblity: Yes (HDR10,HLG,Dolby Vision)
6
-
-
CAT 6 CABLE FOR INTERCONNECTIVITY
305
-
-
Pop-Up Box with HDMI Power, USBand LAN
8
-
-
CABLE CONNECTORS AND OTHER ACCESSORIES
1
-
-
INSTALLATION AND COMMISSIONING CHARGES
1
-
-
Multi-Purpose Hall : 8" 2‑way passive full‑range indoor/outdoor loudspeaker Frequency Response (-3 dB) 60 Hz - 20 kHz¹, Frequency Range (-10 dB) 48 Hz - 20 kHz¹, Rec. Hi-pass Frequency 40 Hz; Axial Sensitivity 94 dB (1W/1m)¹, Max Calculated SPL 123 dB; Coverage (H x V) 90 x 50; Rated System Power 200 W Cont.², 400 W Prog., 800 W Peak, LF Transducer EV8L, 203 mm (8 in) Driver, HF Transducer DH2005, 25 mm (1 in) Exit Compression Driver, Crossover Frequency 1.7 kHz; Nominal Impedance 8 Ω; Minimum Impedance 6 Ω; Connectors 4-Pin Phoenix Connector,
6
-
-
DSP 2 x 650 w power amplifier for live performance applications Maximum RMS Voltage Swing THD = 1%, 1 kHz 55.3 V; Voltage Gain Ref.1 kHz 32.0 dB; THD at 450 W/4 Ω MBW = 80 kHz, 1kHz 0.05%; Frequency Response, ref. 1 kHz 10 Hz to 21 kHz (±1 dB); Input Impedance, Active Balanced 20 k Ω; Signal to Noise Ratio Amplifier, A-weighted, ref to Max. Output Power@ 8 Ω 104 Db; Output Noise, A-weighted -68 dBu, Output Stage Topology Class AB, Power Requirements 240 V, 230 V, 120 V or 100 V; 50 Hz to 60 Hz (factory configured); Power Consumption ⅛ MaximumOutput Power @ 4 Ω 550 W; Mains Fuse 240 V/230 V: T10AH; 120 V/100 V: T20AH; Protection Audio limiters, high temperature, DC, HF, Back-EMF, Peak current limiters, In rush current limiters, Turn on delay, Cooling Front-to-rear, 3-stage-fans,
2
-
-
On-board processors: SPX algorithm: 24 programs, PARAMETER control:1, FOOT SW:1 (FX RTN CH on/off); Phantom power: +48 V; Digital I/O: USB Audio Class 2.0 compliant, Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit; Input Channels: Mono[MIC/LINE] - 4; Mono/Stereo[MIC/LINE] - 2; Stereo[LINE] - 2; STEREO OUT-2, MONITOR OUT-1; PHONES-1; AUX SEND- 2; GROUP OUT- 2;
1
-
-
12" Active Subwoofer Frequency response (-3 dB) 49 Hz - 135 Hz¹, Frequency range (-10 dB) 41 Hz - 165 Hz¹, Maximum SPL 129 Db², Power rating 1200 W, LF transducer EVS-12L 300 mm (12 in), Low-Pass frequency Adjustable: 80 Hz, 100 Hz, 120 Hz, 150 Hz, Connectors (2) XLR/TRS combo jacks and (2) XLR link outputs, Enclosure 15 mm plywood with EVCoat, Grille 18 AWG steel with powdercoat, Color Black or White.
2
-
-
Premium Supercardoid Vocal Microphone Incredible vocal power and clarity, Robust, forgiving, EQ-friendly performance, Superior off-axis rejection, Ultra-low handling nois, Connector Type 3-pin XLR ; Power Requirement Passive; Audio Frequency Response 80 Hz - 16,000 Hz; Polar Pattern Supercardioid; Wired/Wireless Wired; Mic Type Handheld; Element Dynamic; Impedance, Low-Z balanced 600Ω; Open Circuit Voltage 2.2mV/Pascal.
2
-
-
Gooseneck Podium Mic 18" Podium Microphone Connector Type 3-pin XLR ; Depth 7.01" (178mm), Frequency Response (-3 dB) 50 - 20,000 Hz; Weight Net 24.34oz (690g); Family PolarChoice; Element Dual condenser (back-electret), Impedance, Low-Z balanced 200Ω; Open Circuit Voltage 5.6mV/Pascal; Case Material Steel Mic Type Gooseneck Power Requirement 12 - 52 VDC
1
-
-
Speakon Connectors
8
-
-
XLR Male & Female Connectors
20
-
-
32 Channel Wireless Handheld Microphone Receiver Type Synthesized PLL Number of Channels 32 Audio Parameters Power Requirements 12-16 VDC, 500mA max Frequency Response 80 Hz - 18 kHz ± 2 dB; Balanced Output 20 dBV (max @ 40 kHz deviation), Unbalanced Output Adjustable 8 mV to 0.755V RMS; Distortion 1.0%, 0.4% typical (ref 1 kHz, 40 kHz deviation); Signal-to-Noise Ratio 100 dB A-Weighted; Dynamic Range 95 dB Transmitter Specifications Radiated Output 8 mW typica; Back Lit LCD Display Channel, Frequency, Mute, and Battery Level; Microphone Head Electro-Voice PL22 Cardioid Dynamic; Standard Lavalier Microphone Electro-Voice ULM18 Uni-Directional Condenser; TA4F Connector Wiring Pin 1 Ground; Pin 2 Mic Input; Pin 3 +5V bias; Pin 4 +5V thru 2.2k Ω; Power Requirement Two AA batteries; Battery Life (Typical) 14 hours with AA alkaline typical; Bodypack Antenna Flexible external 1/4 wave; Handheld Antenna Internal proprietary
1
-
-
Signal/Mic Wire
150
-
-
9u Floor Standing Rack
1
-
-
2 Core 2 sqmm Speaker Cable;
200
-
-
5,000 lumens WXGA laser light source projector Display system 3 LCD system Size of effective display area 0.64”(16.3 mm) x 3 BrightEra LCD Panel, Aspect ratio: 16:10; Number of pixels 3,072,000 (1280 x 800 x 3) pixels Focus Manual, Zoom - Powered/Manual; Manual, Zoom - Ratio Approx. x 1.6; Throw ratio 1.29:1 to 2.07:1; N/A (Lens Offset Vertical Light source: Type Laser diode Color light output *1 : Mode: Standard 5,000 lm Speaker 16 W (monaural) Video signal input: NTSC, PAL, SECAM, 480/60p, 576/50i, 720/60p, 720/50p, 1080/60i, 1080/50i; The following items are available for HDMI input only; 1080/60p, 1080/50p, 1080/24p;
1
-
-
Motorized 10X8 projector screen.
1
-
-
Installation and Commissioning, tuning
1
-
-
Audio Visual Room Sound System; 15" 2-Way passivespeaker with 1.5" HF Compression drive, 1200 W peak power. Frequency response (-3 dB)1 : 77 Hz - 16 kHz; Frequency range (-10 dB)1 : 52 Hz - 19 kHz; Axial sensitivity1 : 95 dB. Maximum SPL1,2 : 130 dB ; Rec. high-pass frequency: 42 Hz. Coverage (H x V): 90˚ x 60˚; Power handling: 300 W Continuous, 1200 W Peak; LF transducer: EVS-15M 381 mm (15 in); HF transducer: DH-1L 1-inch titanium compression; driver. Crossover frequency: 1.6 kHz; Nominal impedance: 8 Ω. Minimum impedance: 7.0 Ω; Connectors: Dual NL4 Enclosure: Polypropylene; Grille: 18 AWG steel with powdercoat; Suspension: (3) M10 suspension points; Color: Black or white;
4
-
-
15" powered subwoofer Frequency Response (-3 dB) 45 Hz - 150 Hz¹; Frequency Range (-10 dB) 40 Hz - 180 Hz¹; Maximum SPL 133 dB peak² Power Rating 1300 W; LF Transducer EVS-15C 381 mm (15 in) ; Low Pass Frequency Adjustable 80 Hz, 100 Hz, 120 Hz, 150 Hz; Connectors (2) XLR/TRS combo jacks and (2) XLR link outputs; Enclosure 15 mm plywood with EVCoat ;Grille 18 AWG steel with powdercoat
2
-
-
Power Amplifier, 2x1400 watts@4 ohms, FIR Drive Maximum RMS Voltage Swing THD = 1%, 1 kHz 78.8 V, Voltage Gain Ref.1 kHz 32.0 dB, THD at 900 W/4 Ω MBW = 80 kHz, 1kHz 0.05% Frequency Response, ref. 1 kHz 10 Hz to 21 kHz (±1 dB); Input Impedance, Active Balanced 20 k Ω; Signal to Noise Ratio Amplifier, A-weighted, ref to Max. Output Power@ 8 Ω 107 dB Power Consumption ⅛ Maximum Output Power @ 4 Ω 700 W Signal Processing FIR filters, audio limiters, output and array** delay, 10-band** user PEQ, 5-band array PEQ** per channel, load impedance; Remote Control SONICUE sound system software **
2
-
-
12" active pulpit/choir Monitors. 1000 W (Class D); 126 dB max SPL; 50 Hz – 20 kHz, 12” woofer and 1.5” high-frequency titanium compression driver Frequency Response 65 Hz – 18 kHz1; Frequency Range 50 Hz – 20 kHz1; Maximum SPL 126 dB Coverage (Hort. x Vert.) 90° x 60°; Power Rating 1000 Watts; LF Transducer EVS-12K, 300 mm (12 in) Woofer; HF Transducer DH-1K; Connectors (2) XLR/TRS Combo Jack, (1) 3.5 mm Input, and (1) XLR link Output; Enclosure Polypropylene; Grille 18 Gauge Steel with Black Powder Coat
2
-
-
• Ultra-low noise discrete MIC preamp with +48V phantom power. • 8 / 16 mono input channels and 4 stereo input channels. • Each input channel accepts balanced XLR MIC input and TRS LINE input • Low cut for each MIC input. • Each mono input channel is equipped with 3-band EQ, sweepable MID and PEAK LED.• 2 stereo input channels accept mono XLR or TRS input; 2 stereo input channels accepts RCA input. • Each stereo input channel is equipped with 4-band EQ and PEAK LED. • 8 compressor controls and 8 channel insert points. • AUX 1 & AUX 2 send post/pre-fader signal for monitoring or external effects; AUX 3 & FX send post-fader for internal effects or monitoring. • PFL/MUTE and 60mm fader for each channel. • GR1/2, GR3/4 and MAIN L-R buss assignment for each channel. • MAIN MIX installs a pair of balanced XLR and a pair of unbalanced TRS connectors and can be equalized via a 7-band GEQ. • MAIN MIX supports external effect insert. • 24-bit DSP processor provides up to 100 effect presets. • USB player for MP3 playback and recording. • Switch-mode power supply for 100-240Voltage. • USB port for MAIN MIX recording or playback through CH 15/16 (M16) or CH 23/24 (M24).
1
-
-
18" Podium Microphone Connector Type 3-pin XLR Depth 7.01" (178mm) ;Frequency Response (-3 dB) 50 - 20,000 Hz; Weight Net 24.34oz (690g); Family PolarChoice; Element Dual condenser (back-electret); Impedance, Low-Z balanced 200Ω; Open Circuit Voltage 5.6mV/Pascal; Case Material Steel Mic Type Gooseneck Power Requirement 12 - 52 VDC;
2
-
-
Premium Supercardoid Vocal Microphone Incredible vocal power and clarity; Robust, forgiving, EQ-friendly performance; Superior off-axis rejection; Ultra-low handling noise; Connector Type 3-pin XLR: Power Requirement Passiv; Audio Frequency Response 80 Hz - 16,000 Hz; Polar Pattern Supercardioid, Wired/Wireless Wired; Mic Type Handheld; Element Dynamic; Impedance, Low-Z balanced 600Ω; Open Circuit Voltage 2.2mV/Pascal
2
-
-
32 Channel Wireless Handheld Microphone Receiver Type Synthesized PLL Number of Channels 32 Audio Parameters Power Requirements 12-16 VDC, 500mA max Frequency Response 80 Hz - 18 kHz ± 2 dB; Balanced Output 20 dBV (max @ 40 kHz deviation); Unbalanced Output Adjustable 8 mV to 0.755V RMS; Distortion 1.0%, 0.4% typical (ref 1 kHz, 40 kHz ; Signal-to-Noise Ratio 100 dB A-Weighted; Dynamic Range 95 dB Transmitter Specifications; Radiated Output 8 mW typical; Back Lit LCD Display Channel, Frequency, Mute, and Battery Level; Microphone Head Electro-Voice PL22 Cardioid Dynamic; Standard Lavalier Microphone Electro-Voice ULM18 Uni-Directional Condenser; TA4F Connector Wiring Pin 1 Ground; Pin 2 Mic Input; Pin 3 +5V bias; Pin 4 +5V thru 2.2k Ω; Power Requirement Two AA batteries;; Battery Life (Typical) 14 hours with AA alkaline typical;; Bodypack Antenna Flexible external 1/4 wave; Handheld Antenna Internal proprietary
2
-
-
Microphone Stand Big
4
-
-
12 U Floor Standing Amplifier Rack
1
-
-
Speakon Connectors
12
-
-
XLR Male/Female Connectors
70
-
-
Signal / Micx Wire
200
-
-
2 Core 2 Sqmm Speaker Cable
300
-
-
24 channel snake cable with box , 30 mtrs
40
-
-
5,000 lumens WXGA laser light source projector Display system 3 LCD system Size of effective display area 0.64”(16.3 mm) x 3 BrightEra LCD Panel, Aspect ratio: 16:10; Number of pixels 3,072,000 (1280 x 800 x 3) pixels Focus Manual, Zoom - Powered/Manual; Manual, Zoom - Ratio Approx. x 1.6; Throw ratio 1.29:1 to 2.07:1; N/A (Lens Offset Vertical Light source: Type Laser diode Color light output *1 : Mode: Standard 5,000 lm Speaker 16 W (monaural) Video signal input: NTSC, PAL, SECAM, 480/60p, ; 576/50i, 720/60p, 720/50p, 1080/60i, 1080/50i; The following items are available for HDMI input only; 1080/60p, 1080/50p, 1080/24p
1
-
-
4 IN 1 OUT HDMI SWITCHER
1
-
-
HDMI Extender
1
-
-
24 Channel Stage Box
1
-
-
Motorised Projector Screen (10x8) Ft
1
-
-
Desktop Computer with windows Core i7
1
-
-
Installation and Commissioning
1
-
-
40 Seater Conference Hall; Digital Conference Controller with upto 4 cameras, with inbuilt DAFS ( Digital Acoustic Feedback supression ) with the following features and technical specifications : The Control Unit shall have the following features: Built-in digital recorder with internal memory and USB recording. Built-in loudspeaker and headphone socket for listening to recorded discussions before replaying them to the Floor, or listening to recordings. Built-in Digital Acoustic Feedback Suppression (DAFS). USB connector on front of unit for connecting a USB memory stick. 3.5 mm (0.14 in) stereo headphone socket. Micro USB connector on rear of unit for transferring internal memory (recordings) to a PC. Four additional RCA outputs for individual microphone recording, e.g. for recording individual speakers in a courtroom. Additional capacitive touch buttons and LED indicators for: CU loudspeaker volume (or headphones volume, if connected). Start, Pause (hold), and Stop recording.
1
-
-
Digital Conference Discussion device with the following features and technical specifications Plug-and-play functionality. Compact, attractive, ergonomic design, with LED indicator in the Discussion Device and in head of microphone. Choice of short or long fixed microphone with flexible stem. Loudspeaker integrated into front of device. Built-in headphone socket with output level control. Automatic level reduction when microphone is activated (configurable via web browser application of Control Unit): prevents acoustic feedback from headphone to microphone. Configurable as a participant or chairperson’s device: changeable microphone buttons and concealed slide switch at the bottom of the device for configuration purposes. GSM immunity. The device shall have the following user controls and indicators: Microphone button. Color-coded LED indicator above microphone button for showing the status of the device: White (‘Possible‑To‑Speak’) shall indicate that the microphone will be active immediately after pressing the microphone button. Green shall indicate that the participant has pressed the microphone button and the request to speak has been added to the waiting list. Green flashing shall indicate that the participant is first in the waiting list, i.e. next in line to speak. Red shall indicate that the microphone is active.Rotary thumbwheel on side of device for adjusting volume of connected headphones. Concealed initialization button at base of device for re-assigning the network address.
22
-
-
Extention cables 10 meters
4
-
-
Premium Two Way Wall mounted speakers with following
10
-
-
1.5 SQMM SPEAKER CABLE ,15 AWG (75/0.16mm) x 2 Core - ATC
300
-
-
HDMI 15 meter
1
-
-
Screen Size: 75" ; Brightness (cd/m²): Typ. 620 / Peak 850 Native contrast ratio: 6,000:1; Dynamic contrast ratio: 600000:1 Display resolution (H x V, pixels): 3,840 x 2,160 HDR (High Dynamic Range) compatiblity: Yes (HDR10,HLG,Dolby Vision)
1
-
-
Installation and Commissioning
1
-
-
Grille 18 AWG steel with powdercoat
-
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements