Department Of Housing And Urban Affairs Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 25,71,000Document Cost
₹ 20,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2022_DHUA_26621_1Bid Award Id
ViewTender No
CE/H and UA/17/PT-II/21-22/82, date12/08/2022Tender Authority
Department Of Housing And Urban Affairs ViewPurchaser Address
-Website
http://assamtenders.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
140
-
10
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.
660.53
-
10
Earth Work for Indoor Stadium
-
-
-
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.
419.76
-
100
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
301.42
-
10
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.
1085.8
-
10
Masonry Work For Auditorium
-
-
-
Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
451.76
-
10
Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.
83.64
-
10
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand).
44.3
-
10
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)
7.23
-
10
HALF BRICK MASONRY
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in :Cement mortar 1:3 (1 cement : 3 coarse sand)
133.91
-
10
Masonry Work for Indoor Stadium
-
-
-
Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
897.64
-
10
Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.
23.17
-
10
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)
89.23
-
10
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand).
6.39
-
10
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1:3 (1 cement : 3 coarse sand)
2106.68
-
10
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)
2.7
-
10
Dismantling Work for Auditorium
-
-
-
Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead For thickness of tiles above 25 mm and up to 40 mm
702.57
-
10
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar
3.45
-
10
Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : Thickness above 25 mm up to 40 mm
704.38
-
10
Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead
659.85
-
10
Dismantling Work for Indoor Stadium
-
-
-
Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charg
49.62
-
10
Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work
13148.1
-
10
Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. Wedge expansion type. Fastener with threaded dia 12 mm
576
-
10
Concrete Work For Auditorium
-
-
-
1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size).
62.5
-
10
Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).
8.28
-
10
Concrete Work for Indoor Stadium
-
-
-
1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)
39.96
-
10
Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size)
33.85
-
10
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth
70.47
-
10
FORM WORK For Auditorium
-
-
-
Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete.
17.44
-
10
Columns, Pillars, Piers, Abutments, Posts and Struts.
98.64
-
10
Lintels, beams, plinth beams, girders, bressumers and cantilevers.
36.63
-
10
FORM WORK for Indoor Stadium
-
-
-
Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete
80.24
-
10
Columns, Pillars, Piers, Abutments, Posts and Struts
1207.67
-
10
Lintels, beams, plinth beams, girders, bressumers and cantilevers
892.18
-
10
Suspended floors, roofs, landings, balconies and access platform
790.24
-
10
Stairs, (excluding landings) except spiral-staircases
21.03
-
10
Reinforce Cement Concrete Works For Auditorium
-
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size).
13.09
-
10
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
7.64
-
10
Reinforce Cement Concrete Works for Indoor Stadium
-
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)
110.38
-
10
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
267.46
-
10
Cement Plaster For Auditorium
-
-
-
15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)
293.09
-
10
12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) .
133.91
-
10
Cement plaster with a floating coat of neat cement12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand).
140.76
-
10
Cement Plaster for Indoor Stadium
-
-
-
15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)
5013.98
-
10
12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)
2150.54
-
10
15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)
1693.08
-
10
Flooring For Auditorium
-
-
-
VITRIFIED FLOOR TILES Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm.
227.37
-
10
Crazy ceramic tile flooring, with under layer 12 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), with joints not exceeding 5 mm, including filling the gaps with ordinary cement mixture & mixing with synthetic polyester fibre, triangular in shape having specific gravity of 1.34 to 1.40, cross section size ranging from 10 to 40 micron & length upto 6 mm , mixing fibre @ 125 grams per 50 kg of cement in cement mortar, including providing and mixing water proofing material in mortar @ 1 kg per 50 kg of cement, all complete as per direction of Engineer-in-charge.
140.34
-
10
Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
73.79
-
10
Flooring for Indoor Stadium
-
-
-
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate
1.57
-
10
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
405.77
-
10
Crazy ceramic tile flooring, with under layer 12 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), with joints not exceeding 5 mm, including filling the gaps with ordinary cement mixture & mixing with synthetic polyester fibre, triangular in shape having specific gravity of 1.34 to 1.40, cross section size ranging from 10 to 40 micron & length upto 6 mm , mixing fibre @ 125 grams per 50 kg of cement in cement mortar, including providing and mixing water proofing material in mortar @ 1 kg per 50 kg of cement, all complete as per direction of Engineer-in-charge.
49.73
-
10
Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
86.22
-
10
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
204.99
-
10
Painting Work For Auditorium
-
-
-
Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer.
4075.44
-
10
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
4075.44
-
10
Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre.
4075.44
-
10
Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work.
2824.47
-
10
EXTERIOR FINISHING Finishing walls with water proofing cement paint of required shade :New work (Two or more coats applied @ 3.84 kg/10 sqm) .
1301.95
-
10
EXTERIOR FINISHING Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).
1301.95
-
10
Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
3667.9
-
10
Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge
211.88
-
10
Cleaning the sand stone surface and removing dirt, dust, bird dropping, grease, oil, algae, fungus, monkey beats, vegetable growth etc., including providing, applying and washing the surface with liquid Ammonia Chemical of 5% solution and other chemical cleaning agent as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand and manufacturer, with the help of required scrubbers and also cleaning with machine operated water jet mixed with desired quantity of fine silica where ever required, without causing any scratching/ damage to the stone surface and finally washing the surface with clean water with the help of pressure jet machine, complete in all respect, including taking all precautions to safeguard ventilators, windows, doors etc. by suitable covering so as to avoid any damage to the building/structure, all as per direction of Engineerin-charge (The rate is inclusive of all materials & labours involved except scaffolding).
211.88
-
10
Providing and applying antifungal wash treatment using 3% solution of sodium pentachlorophenate, of reputed brand and manufacturer, on cleaned sand stone surface at desired locations as per direction of Engineer-in-charge (The rate is inclusive of all materials & labours involved except scaffolding).
262.14
-
10
Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
322.45
-
10
Painting Work for Indoor Stadium
-
-
-
Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :
Water thinnable cement primer
7120.66
-
10
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer
43.86
-
10
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
7120.66
-
10
Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre
7120.66
-
10
Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work
5013.98
-
10
Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
2106.68
-
10
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm
43.86
-
10
Steel Work For Auditorium
-
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo Mechanically Treated bars of grade Fe-500D or more.
2568.57
-
10
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile B. Fixing with adjustable lugs with split end tail to each jamb.
52.8
-
10
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.
172.27
-
10
Railing/Balustrade Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
650.1
-
10
Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. Wedge expansion type. Fastener with threaded dia 12 mm.
8
-
10
Steel Work for Indoor Stadium
-
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more
47190.95
-
10
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile B. Fixing with adjustable lugs with split end tail to each jamb.
137.9
-
10
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
64.15
-
10
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes
5777.57
-
10
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
36595.3
-
10
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube
244.81
-
10
Door/Window Works For Auditorium
-
-
-
Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin-Charge.
19.8
-
10
Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 30 mm thick plain PVC door shutters.
6.3
-
10
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.
22.68
-
10
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm).
0.72
-
10
Aluminium Partition Wall: Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness (weight not
less than 20 kg/ sqm).
13.25
-
10
Door/Window Works for Indoor Stadium
-
-
-
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
51.45
-
10
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)
25.83
-
10
Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.
1878.97
-
10
False Ceiling Work For Auditorium
-
-
-
Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.
229.88
-
10
ROOF INSULATION For Auditorium
-
-
-
Providing and laying roof insulation with 40 mm thick impervious sprayed, closed cell free Rigid Polyurethane foam over deck insulation conforming to IS - 12432 Pt. III (density of foam being 40-45 kg/ cum), over a coat of polyurethane primer applied @ 6-8 sqm per litre, laying 400 G polythene sheet over PUF spray and providing a wearing course of 40 mm thick cement screed 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) in chequered rough finish, in panels of 2.5 m x 2.5 m and embedding with 24 G wire netting and sealing the joints with polymerized mastic, all complete as per direction of Engineer-in-Charge.
660.53
-
10
Roofing For Auditorium
-
-
-
Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275 gm/m² .
169.24
-
10
Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gm/m².
5
-
10
Roofing For Indoor Stadium
-
-
-
Laying Truss Less Roof. Dyna Make. Laying Truss Less Roof
1050.4
-
10
HANGER CLIT
256
-
10
Providing and fixing 50 mm thick extruded polystyrene rigid insulation board of required size underdeck on ceiling surface, complying with ISO 4898:2008 & ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as per ASTM C 578 (measured as per IS 3346), compressive strength of 350 kPa listed as per ASTM D 1621, density of 34-36 kg/cum as per ASTM D 1622, water absorptions ? 1% by volume as per ASTM D 2842, oxygen index of 24.1 to listed as per ASTM D 2863, cell size 0.4 mm of dia (max) as per ASTM D 3576. Fire retardent property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 class A, fixed with suitable water based adhesive and fastener, complete in all respect as per the direction of Engineer-in-Charge.
991.97
-
10
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
475.79
-
10
Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete: Gutter (600 mm over all girth)
120
-
10
Providing and fixing roofing consist of 0.8 mm thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3mm laid at 100x100 mm grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately).
545.28
-
10
INTERNAL ROAD For Auditorium
-
-
-
Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.
30
-
10
Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).
30
-
10
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30.
36
-
10
Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge
6
-
10
Providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour of M -30 grade made of C&D waste by block making machine with vibratory compaction laid in required pattern and including over 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.
120
-
10
Site and Jungle Clearenace For Auditorium
-
-
-
Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.
300
-
10
Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.
300
-
10
Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 60 cm girth upto and including 120 cm girth.
50
-
10
Fencing For Auditorium
-
-
-
Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately).
40
-
10
Landscaping
-
-
-
For Horticulture operations including 300mm earth filling, grassing, tree plantation/ shrubs and potted plants etc.a) For Auditorium
202.6
-
10
b) For Indoor Starium
391.5
-
10
Fire Fighting and Alarm
-
-
-
For Fire Fighting with wet riser and sprinkler system, a)For Auditorium
699.3
-
10
Fire Fighting Downcomer System, b) For Indoor Stadium
2323.42
-
10
For Fire Alarm System(Automatic), a) For Auditorium
699.3
-
10
Fire Alirm System Manual Fire Alarm System, b) For Indoor Stadium
2323.42
-
10
CCTV WORKS
-
-
-
CCTV System(Internal), a) For Auditorium
699.3
-
10
CCTV System(Internal Building Security), b) For Indoor Stadium
2323.42
-
10
CCTV System(External surveillance), a)For Auditorium
675.6
-
10
RWH for Indoor Stadium
-
-
-
Rain Water Harvesting(RWH)
100
-
10
Exterior Cladding of the building
-
-
-
Auditorium
180.42
-
10
Structural Glazing for Indoor Stadium
-
-
-
Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- inCharge.
147.45
-
10
Providing, fabricating and supplying shadow box of required size and shape, for fixing in the spandrel portion of the structural glazing, in linear as well as curvilinear portions of the building by providing semi -rigid, inorganic, non-combustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183 and BS: 3958 Part 5. The insulation layer shall have facing (factory bonded on surface # 1 of the fibre glass insulation layer), of black non-woven fibre glass tissue of nominal thickness 0.5 mm and nominal mass not less than 60 gm /sqm, made of randomly oriented glass fibres distributed in a binder by a wet-lay process including fixing 1.5 mm thick solid aluminum sheet backing using, 6 mm thick cement board including SS rivets, nuts, bolts, washers etc complete.
147.45
-
10
SANITARY AND WATER SUPPLY WORKS FOR AUDITORIUM
-
-
-
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
5
-
10
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern
2
-
10
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
5
-
10
Providing and fixing 100 mm sand cast Iron grating for gully trap
5
-
10
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
5
-
10
Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
2
-
10
Providing and fixing toilet paper holder : C.P. brass
5
-
10
Providing and fixing soil, waste and vent pipes : 100 mm dia. Sand cast iron S&S pipe as per IS: 1729
5
-
10
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia. Sand cast iron S&S as per IS - 1729
5
-
10
Providing and fixing plain bend of required degree. 100 mm dia. Sand cast iron S&S as per IS - 1729
5
-
10
Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100 mm. Sand cast iron S&S as per IS - 1729
3
-
10
Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms
5
-
10
Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms
5
-
10
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.
5
-
10
Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.
5
-
10
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work. 20 mm nominal dia Pipes
65.2
-
10
80 mm nominal dia Pipes
57
-
10
100 mm nominal dia Pipes
75.2
-
10
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes
25
-
10
32 mm nominal dia Pipes
10
-
10
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
5
-
10
Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.
5000
-
10
C.P. BRASS FITTINGS Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore
5
-
10
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore
3
-
10
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore
17
-
10
Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms
5
-
10
SANITARY AND WATER SUPPLY WORKS FOR INDOOR STADIUM
-
-
-
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
16
-
10
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern
8
-
10
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
16
-
10
Providing and fixing 100 mm sand cast Iron grating for gully trap
16
-
10
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
16
-
10
Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
16
-
10
Providing and fixing toilet paper holder : C.P. brass
16
-
10
Providing and fixing soil, waste and vent pipes : 100 mm dia. Sand cast iron S&S pipe as per IS: 1729
16
-
10
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia. Sand cast iron S&S as per IS - 1729
16
-
10
Providing and fixing plain bend of required degree. 100 mm dia. Sand cast iron S&S as per IS - 1729
16
-
10
Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100 mm. Sand cast iron S&S as per IS - 1729
20
-
10
Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms
16
-
10
Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms
16
-
10
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.
16
-
10
Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.
16
-
10
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work. 20 mm nominal dia Pipes
48
-
10
80 mm nominal dia Pipes
24
-
10
100 mm nominal dia Pipes
86.2
-
10
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes
70
-
10
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
5
-
10
Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :icks of class designation 7.5
2
-
10
Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.
10000
-
10
C.P. BRASS FITTINGS Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore
16
-
10
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore
8
-
10
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore
32
-
10
BORING for Indoor Stadium
-
-
-
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. All types of soil. 300 mm dia
200
-
10
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia
150
-
10
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia
50
-
10
Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge
15
-
10
Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
48
-
10
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia
1
-
10
Electrical Works For Auditorium
-
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
230
-
10
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
300
-
10
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
2200
-
10
2 X 4 sq. mm + 1 X 4 sq. mm earth wire
80
-
10
2 X 6 sq. mm + 1 X 6 sq. mm earth wire
240
-
10
2 X 10 sq. mm + 1 X 10 sq. mm earth wire
180
-
10
4 X 10 sq. mm + 2 X 10 sq. mm earth wire
200
-
10
Supplying and fixing metal box of following sizes (normal) on surface or recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 100 mm x 100 mm x 60 mm deep
40
-
10
180 mm x 100 mm x 60 mm deep
25
-
10
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch
6
-
10
3 pin 5/6 A socket outlet
6
-
10
TV antenna socket outlet
4
-
10
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
6
-
10
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
30
-
10
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)
4
-
10
3 Module (100mmX75mm)
6
-
10
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
10
-
10
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
12
-
10
Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.
416
-
10
Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc., including supplying and fixing ball and socket arrangement, 2 no. down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.
4
-
10
Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
6
-
10
Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep
19
-
10
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). . 12 way, Double door
5
-
10
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 8 way (4 + 24), Double door
4
-
10
Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB/MCCBs (but without MCCB/MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.). 8 way (4 + 24), Double door
1
-
10
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
112
-
10
Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps
5
-
10
Supplying and Fixing Singe Pole Blanking Plate in the existing MCB DB complete etc. as required.
18
-
10
Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
8
-
10
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness
70
-
10
300 mm width X 50 mm depth X 1.6 mm thickness
100
-
10
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness
4
-
10
300 mm width X 50 mm depth X 1.6 mm thickness
4
-
10
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness
3
-
10
300 mm width X 50 mm depth X 1.6 mm thickness
2
-
10
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
16
-
10
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Metre long etc. with charcoal/ coke and salt as required.
8
-
10
Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)
80
-
10
Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
80
-
10
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
160
-
10
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
160
-
10
Providing and fixing 4mm dia.copper wire on surface or in recess for loop earthing as required.
200
-
10
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.
350
-
10
LIGHTNING CONDUCTOR Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required.
5
-
10
Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.
30
-
10
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)
140
-
10
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)
40
-
10
Providing and fixing testing joint, made of 20 mm X 3 mm thick copper strip, 125 mm long, with 4 nos. of tinned brass bolts, nuts, chuck nuts and spring washers etc. complete as required.
20
-
10
Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.
10
-
10
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 70 sq. mm (38mm)
2
-
10
3½ X 150 sq. mm (70mm)
4
-
10
3½ X 185 sq. mm (70mm)
4
-
10
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 150 sq. mm
2
-
10
Supply and laying of following size of PVC/XLPE insulated and PVC sheathed 11 KV grade aluminium conductor LT armoured UG cable laid in ground/partially in air (10% of cable length) including excavation of cable trench upto depth of 75cm. Refilling, protective brick covering, sand cushioning etc. complete handling of surplus soil, debries etc. to proper place as speciefied and directed by the deptt. 4.00 mm2 3core U.G. Cable
120
-
10
6.00 mm2 3core U.G. Cable
90
-
10
25.00 mm² 3½ core U.G. Cable
40
-
10
70.00 mm² 3½ core U.G. Cable
60
-
10
150.00 mm² 3½ core U.G. Cable
90
-
10
185.00 mm² 3½ core U.G. Cable
110
-
10
Supply and laying of following size of PVC/XLPE insulated and PVC sheathed 11 KV grade aluminium conductor LT armoured UG cable laid in pucca flooring road crossing, drain crossing and partially in air through GI pipe (Tata/Nezone make) with necy. bend and socket including excavation and refilling the trench and making good damage done as specified and directed by the Deptt. 4.00 Sq.mm 3 Core U.G. cable in 25mm dia medium duty G.I. pipe
30
-
10
6.00 Sq.mm 3 Core U.G. cable in 32mm dia medium duty G.I. pipe
20
-
10
25.00 mm² 3½ core U.G. Cable in 40mm dia medium quality G.!. Pipe
10
-
10
70.00 sqmm 31/2 core UG cable in 50mm dia medium quality.
10
-
10
150.00 sqmm 31/2 core UG cable in 80mm dia medium quality.
20
-
10
185.00 sqmm 31/2 core UG cable in 80mm dia medium quality.
10
-
10
Design, Manufacture, Supplying, Fixing in position, Testing & Commissioning of floor mounted Feeder Pillar including all components housed in 16 SWG cubicle type sheet steel floor mounting, outdoor type as required with dust proof, hinged and lockable doors complete with inter-connections with copper wires, taps, bonding to earth & painting in line with specification, complete with neutral, earth strips of adequate size & drawings. a)Incoming : 400 Amps 4P 36KA MCCB- 2Nos.b)400 A, 4P, on-load Changeover switch - 1 No. c)Busbar: 640 Amps TPN Copper Busbar (40mmX10mm). Outgoings: d)250 Amps 4P 25KA MCCB-1No. e)100 Amps 4P 25KA MCCB-2Nos. f)40 Amps 4P 25KA MCCB-1No. g)40 Amps 4P MCB-6Nos. h)40 Amps DP MCB-9Nos. i)32 Amps DP MCB-3Nos.
1
-
10
Feeder Pillar - STL: Design, Manufacture, Supplying, Fixing in position, Testing & Commissioning of floor mounted Feeder Pillar including all components housed in 16 SWG cubicle type sheet steel floor mounting, outdoor type as required with dust proof, hinged and lockable doors complete with inter-connections with copper wires, taps, bonding to earth & painting in line with specification, complete with neutral, earth strips of adequate size & drawings. a)Incoming : 40 Amps 4P 25KA MCCB. b)Astronomical timer switch – 1 no. c)Busbar: 100 Amps TPN Copper Busbar (25mmX3mm). Outgoings: d)10 amps DP MCB –6 nos . e)16 amps switch and socket – 1 no. f)24" tube light with switch inside feeder pillar – 1 no.
1
-
10
MCB AND MCCB: Supplying and fixing following rating, Single pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. A)
2
-
10
Supplying and fixing following rating, Double pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. A) 40 amps
5
-
10
Supplying and fixing following rating, Triple pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps
8
-
10
63 amps
6
-
10
Supplying and fixing following rating, Four pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps
4
-
10
Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 A, 25KA, 4P MCCB
1
-
10
250 A, 25KA, 4P MCCB
1
-
10
Supplying, installation, testing and Commission of Recessed type FOOT / Skirting Light of make LEGRAND brand Lyncus cat. no. 677248 with 3 nos. of 1W LED lamp. (FT)
75
-
10
Supplying of the following indoor Decorative Recess mounted LED down lighter luminaries with colour changing facility of Make-J N Lighting India model no-EB-9327 (30W) LED complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make). [DL]
170
-
10
Supplying of the following indoor Decorative Recess mounted LED down lighter luminaries with colour changing facility of Make-J N Lighting India model no-EB-9327 (18W) LED complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make). [SP]
46
-
10
Supplying of the following indoor Decorative Recess mounted LED down lighter luminaries with colour changing facility of Make-J N Lighting India model no-EB-9333(6W) LED complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make). [CL]
12
-
10
Supplying of the following indoor Decorative Recess mounted LED down lighter luminaries with colour changing facility of Make-J N Lighting India model no-EB-9655(15W) LED complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make). [CLT]
184
-
10
Supplying of the following indoor Decorative Recess mounted LED Panel light luminaries with colour changing facility of Make-J N Lighting India model no-EB-9955(15W) LED complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make). [PL]
18
-
10
Supplying of 1200 mm sweep Ceiling fan of make HAVELLS Cat/Brand Cat/PACER Ceiling Fan of colour White, Brown or Bianco complete with down rod or equivalent etc. [F]
4
-
10
Supplying of 300 mm sweep exhaust fan of make HAVELLS Cat/Brand VENTIL AIR -DS complete with all accessories complete or equivalent. [EF]
6
-
10
Supplying of 450 mm sweep Heavy duty exhaust fan 900rpm of make HAVELLS Cat/Brand TURBO FORCE-SP complete with all accessories complete or equivalent. [EFH]
7
-
10
Supplying and fixing of 400 mm sweep Wall fan of make HAVELLS Cat/Brand Swing Wall Fan of colour White, Brown or Bianco complete with down rod or equivalent etc. [WF]
2
-
10
Supplying with fitting and fixing sheet steel cable junction box of size 40cm x 20cm x 15 cm made of 16 SWG thick MS Sheet with provision for hinge door and panel locking arrangement complete painted with 2 coats of metal primer and 2 coats of enamelled gloss paint of approved brand and manufacture to give an even shape including cleaning surface to remove of all dirt, dust and other foreign matter, the box is to be fitted on the bottom section of pole with minimum 165 mm dia 25 mm x 5mm size flat iron pole clamp complete with making necessary connection as directed consisting of the following electrical items. 6 amp "L" series SP MCB as outgoing - 2 Nos.
18
-
10
Supplying, installation, testing and commissioning of the following of the street light luminairies of the following specification "Die Cast Aluminum housing acting as Heat Sink for reliable performance. ü Prismatic Diffuser to ensure Road Light Distribution Operating Voltage 220 – 240V /50 Hz AC ü Luminaire Efficacy of 60 lm/W ü CRI : 75 ü Ingress Protection : IP 65ü Suitable for side entry with pole diameter of 28mm to 40mm conforms to IEC598 Section 5 part 1, conforms to IEC598 Section 4 part 1, has lifetime of 50000 Hours with constant lumen output. ü Output luminaous flux of luminaire - 5700 Lumens. (a) WIPRO make Cat No.LR02-102-XXX-57-XX 90W LED. [STL]
6
-
10
Supplying including installation of the Octagonal poles shall be designed to withstand the maximum wind speed of 169 km/hr. The top loading i.e. area and weight of fixtures are to be considered to calculate maximum deflection of the poles and the same shall meet the requirement of BS:5649 Part VI 1982. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding of the pole shaft. The welding of the pole shaft shall be done by Submerged Welding process. All octagonal pole shafts shall be provided with the rigid flange plate of suitable thickness with provision for fixing 4 foundation bolts. The base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside. The welding shall be done as per process approved by Third Party Inspection agency. (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make). Pole Type BOP or equivalent-9030 Height 9m The materials of the pole as follows : Conforming to grade S355JO Conforming to grade S355JO, Base Plate :- Fe 410 Conforming to IS 226/ IS 2062, Foundation Bolts:- 6.8 Gr. As per IS 1367, Pole Sections:- The Octagonal Poles shall be in single piece with single longitudinal welding join, Galvanization :- The poles shall be hot dip galvanized as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 65 micron. The galvanizing shall be done in single dipping. Door opening:- The Octagonal poles shall have door of approximate 500 mm length at the elevation of 500 mm from the base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connection as approved by the Depts.. The door shall be flush with the exterior surface and shall have suitable locking arrangement. The pole shall be adequately strengthened at the location of the door compensate for the loss in section. There shall also be suitable arrangement for the purpose of earthing, Smart pack Junction box with 6 MCB & Terminals for mounting inside base compartment of Pole. Top Dia. :- (A/ 70, Bottom Dia.:- (A/ 155 , Sheet Thickness :- 3mm , Base Plate Dimensions :- (L x B x 260 x 260 x 16, Foundation Bolt Size :- (no. x dia.) 4 x 24 Dia, Pitch Circle Dia.:- (PC 250 Bolt Length:- 750, Projected Bolt Length :-125 Anchor plate thickness :- 4 mm , Pole Foundation :- The octagonal poles shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. Foundation:- The foundation shall be done with ( Earth work 2.04 cubic Meters.RCC 1:1.5 : 3 proportion 0.65 cubic metres. Steel 22.43 Kg. Shuttering 4.32 square metres. = 22.43 Kg.
6
-
10
Supplying including fitting and fixing of Hot Dip galvanised arm bracket for installation of luminaries. Header with top cap 300 mm long pipe of thickness 3 with arrangement to fix on pole top with 3 Nos. of bolts. i Armed of required length size 48.3mm out side dia x 3.25mm thick (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make) Stiffener plate from arm of the following types : Single arm bracket 1000mm long for 3m to 10 metre. Poles.
6
-
10
Supplying and fixing of Fan box (AKG or equivalent as approved by the Deptt.)with inbuild rod as required.
6
-
10
Supply, Installation antistatic rubber mat suitable for 1.1 KV Voltage grade
4
-
10
Supplying including installation, testing and commissioning of Air/Water Cooled Diesel Generator set coupled to suitable alternator of 220/415 V, AC, 1/3-Phase 0.8 p.f.(la mounted on a 1) M.S. Fabricated base frame.,2) M.S. fuel tank of required capacity.,3) Residual Silencer.,4) Standard Control Panel.5) Suitable batteries with lead.,5) First fill of lube oil.,6) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the Technical Specification.. as per manufacturer. (RANGE FROM 5 KVA TO 625 KVA) KOEL/Kirloskar green/bliss, Leyland, Volvo Penta, Perkinson, Mahindra, Greaves, Escort engine and Kirloskar, Stamford, Leroy somer alternator. KVA- PHASE- Approx size- Approx Wt - COOLING. 200 - 3 -3200x1300x1805 -1950 Kg -WATER CoolIed
1
-
10
Electrical Works For Indoor Stadium
-
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
206
-
10
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
400
-
10
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
2200
-
10
2 X 4 sq. mm + 1 X 4 sq. mm earth wire
220
-
10
2 X 6 sq. mm + 1 X 6 sq. mm earth wire
250
-
10
2 X 10 sq. mm + 1 X 10 sq. mm earth wire
160
-
10
4 X 10 sq. mm + 2 X 10 sq. mm earth wire
250
-
10
4 X 16 sq. mm + 2 X 16 sq. mm earth wire
30
-
10
Supplying and fixing metal box of following sizes (normal) on surface or recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 100 mm x 100 mm x 60 mm deep
30
-
10
180 mm x 100 mm x 60 mm deep
15
-
10
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch
26
-
10
3 pin 5/6 A socket outlet
26
-
10
TV antenna socket outlet
4
-
10
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
16
-
10
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
30
-
10
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)
4
-
10
3 Module (100mmX75mm)
46
-
10
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
14
-
10
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
24
-
10
Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.
142
-
10
Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc., including supplying and fixing ball and socket arrangement, 2 no. down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.
4
-
10
Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
44
-
10
Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep
32
-
10
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 6 way, Double door
15
-
10
8 way, Double door
2
-
10
12 way, Double door
4
-
10
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 4 way (4 + 12), Double door
6
-
10
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 8 way (4 + 24), Double door
1
-
10
Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB/MCCBs (but without MCCB/MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.). 8 way (4 + 24), Double door
1
-
10
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
171
-
10
Double pole
15
-
10
Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps
4
-
10
Supplying and Fixing Singe Pole Blanking Plate in the existing MCB DB complete etc. as required.
18
-
10
Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
8
-
10
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness
160
-
10
300 mm width X 50 mm depth X 1.6 mm thickness
140
-
10
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness
6
-
10
300 mm width X 50 mm depth X 1.6 mm thickness
4
-
10
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness
2
-
10
300 mm width X 50 mm depth X 1.6 mm thickness
2
-
10
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
16
-
10
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Metre long etc. with charcoal/ coke and salt as required.
8
-
10
Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)
60
-
10
Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
60
-
10
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
120
-
10
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
120
-
10
Providing and fixing 4mm dia.copper wire on surface or in recess for loop earthing as required.
150
-
10
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.
200
-
10
LIGHTNING CONDUCTOR Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required.
8
-
10
Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.
30
-
10
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)
60
-
10
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)
50
-
10
Providing and fixing testing joint, made of 20 mm X 3 mm thick copper strip, 125 mm long, with 4 nos. of tinned brass bolts, nuts, chuck nuts and spring washers etc. complete as required.
10
-
10
Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.
10
-
10
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 35 sq. mm (28mm)
2
-
10
3½ X 120 sq. mm (70mm)
1
-
10
Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 70 sq. mm
1
-
10
3½ X 120 sq. mm
1
-
10
Supply and laying of following size of PVC/XLPE insulated and PVC sheathed 11 KV grade aluminium conductor LT armoured UG cable laid in ground/partially in air (10% of cable length) including excavation of cable trench upto depth of 75cm. Refilling, protective brick covering, sand cushioning etc. complete handling of surplus soil, debries etc. to proper place as speciefied and directed by the deptt. 4.00 mm2 3core U.G. Cable
160
-
10
6.00 mm2 3core U.G. Cable
416
-
10
10.00 mm2 3core U.G. Cable
60
-
10
25.00 mm² 3½ core U.G. Cable
70
-
10
120.00 mm² 3½ core U.G. Cable
40
-
10
Supply and laying of following size of PVC/XLPE insulated and PVC sheathed 11 KV grade aluminium conductor LT armoured UG cable laid in pucca flooring road crossing, drain crossing and partially in air through GI pipe (Tata/Nezone make) with necy. bend and socket including excavation and refilling the trench and making good damage done as specified and directed by the Deptt. 4.00 Sq.mm 3 Core U.G. cable in 20mm dia medium duty G.I. pipe
40
-
10
6.00 Sq.mm 3 Core U.G. cable in 32mm dia medium duty G.I. pipe
20
-
10
10.00 Sq.mm 3 Core U.G. cable in 32mm dia medium duty G.I. pipe
20
-
10
25.00 mm² 3½ core U.G. Cable in 40mm dia medium quality G.!. Pipe
10
-
10
120.00 sqmm 31/2 core UG cable in 80mm dia medium quality.
10
-
10
Design, Manufacture, Supplying, Fixing in position, Testing & Commissioning of floor mounted Feeder Pillar including all components housed in 16 SWG cubicle type sheet steel floor mounting, outdoor type as required with dust proof, hinged and lockable doors complete with inter-connections with copper wires, taps, bonding to earth & painting in line with specification, complete with neutral, earth strips of adequate size & drawings. a)Incoming : 160 Amps 4P 25KA MCCB- 2Nos. b)160 A, 4P, on-load Changeover switch - 1 No c)Busbar: 320 Amps TPN Copper Busbar (40mmX5mm) Outgoings: d)63 Amps 4P 25KA MCCB-1No. e)40 Amps 4P 25KA MCCB-No. f)40 Amps 4P MCB-6Nos. g)40 Amps DP MCB-4Nos. h)32 Amps DP MCB-18Nos.
1
-
10
Design, Manufacture, Supplying, Fixing in position, Testing & Commissioning of floor mounted Feeder Pillar including all components housed in 16 SWG cubicle type sheet steel floor mounting, outdoor type as required with dust proof, hinged and lockable doors complete with inter-connections with copper wires, taps, bonding to earth & painting in line with specification, complete with neutral, earth strips of adequate size & drawings. a)Incoming : 40 Amps 4P 25KA MCCB b)Astronomical timer switch – 1 no. c)Busbar: 100 Amps TPN Copper Busbar (25mmX3mm) Outgoings: d)10 amps DP MCB –6 nos e)16 amps s witch and socket – 1 no.f)24" tube light with switch inside feeder pillar – 1 no.
1
-
10
Supplying and fixing following rating, Single pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps
2
-
10
Supplying and fixing following rating, Double pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps
4
-
10
Supplying and fixing following rating, Triple pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps
4
-
10
Supplying and fixing following rating, Four pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps
8
-
10
Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 63 A, 25KA, 4P MCCB
1
-
10
Supplying, installation, testing and Commission of Recessed type FOOT / Skirting Light of make LEGRAND brand Lyncus cat. no. 677248 with 3 nos. of 1W LED lamp. (FT)
20
-
10
Supplying, installation, testing and Commission of Superior finish extruded LED Batten white powder coated pressure die cast aluminium body with High transmitivity, non Yellowing PMMA diffuser with driver and accessories pre-wired upto terminal block assembly. LED Luminaires of make PHILIPS Cat No. BN021C LED20S PSU CDL G LED 18W or equivalent inlcuding lamps etc. complete [TL]
142
-
10
Supplying,installation,testing and commissioning of the following integral flood lighting luminaires conforming to IP 65 / IP 66 suitable for vertical and horizontal mounting applications pressure die cast powder coated aluminium alloy housing with corrosion resistance powder coating using nano Technology transparent injection moulded poly carbonate UV stabilized diffuser having high impact strength to withstand min IK09 with high power LED and unique flood optics to ensure uniform light distribution and maintenance free system ideal for area lighting, high mast lighting, sports lighting and billboard. The luminaires should be equiped with external surge protection device to withstand 10 KV / 5KV including connection with 2.5 sqmm 3 core PVC insulated round copper conductor as required and as directed by the department. PHILIPS MAKE CAT REF: BVP 483 LED210 CW SMB PSU GR 176Watt LED. [CH]
20
-
10
Supplying,installation,testing and commissioning of the following integral flood lighting luminaires conforming to IP 65 / IP 66 suitable for vertical and horizontal mounting applications pressure die cast powder coated aluminium alloy housing with corrosion resistance powder coating using nano Technology transparent injection moulded poly carbonate UV stabilized diffuser having high impact strength to withstand min IK09 with high power LED and unique flood optics to ensure uniform light distribution and maintenance free system ideal for area lighting, high mast lighting, sports lighting and billboard. The luminaires should be equiped with external surge protection device to withstand 10 KV / 5KV including connection with 2.5 sqmm 3 core PVC insulated round copper conductor as required and as directed by the department. PHILIPS MAKE CAT REF: SM365 LED32-6500 PSU-OD WH 32Watt LED. [DL]
110
-
10
Supplying of 1200 mm sweep Ceiling fan of make HAVELLS Cat/Brand Cat/PACER Ceiling Fan of colour White, Brown or Bianco complete with down rod or equivalent etc. [F]
44
-
10
Supplying of 300 mm sweep exhaust fan of make HAVELLS Cat/Brand VENTIL AIR -DS complete with all accessories complete or equivalent. [EF]
16
-
10
Supplying of 450 mm sweep Heavy duty exhaust fan 900rpm of make HAVELLS Cat/Brand TURBO FORCE-SP complete with all accessories complete or equivalent. [EFH]
16
-
10
Supplying with fitting and fixing sheet steel cable junction box of size 40cm x 20cm x 15 cm made of 16 SWG thick MS Sheet with provision for hinge door and panel locking arrangement complete painted with 2 coats of metal primer and 2 coats of enamelled gloss paint of approved brand and manufacture to give an even shape including cleaning surface to remove of all dirt, dust and other foreign matter, the box is to be fitted on the bottom section of pole with minimum 165 mm dia 25 mm x 5mm size flat iron pole clamp complete with making necessary connection as directed consisting of the following electrical items. 6 amp "L" series SP MCB as outgoing - 2 Nos.
6
-
10
Supplying, installation, testing and commissioning of the following of the street light luminairies of the following specification "Die Cast Aluminum housing acting as Heat Sink for reliable performance. ü Prismatic Diffuser to ensure Road Light Distribution Operating Voltage 220 – 240V /50 Hz AC ü Luminaire Efficacy of 60 lm/W ü CRI : 75 ü Ingress Protection : IP 65ü Suitable for side entry with pole diameter of 28mm to 40mm conforms to IEC598 Section 5 part 1, conforms to IEC598 Section 4 part 1, has lifetime of 50000 Hours with constant lumen output. ü Output luminaous flux of luminaire - 5700 Lumens. (a) WIPRO make Cat No.LR02-102-XXX-57-XX 90W LED. [STL]
6
-
10
Supplying including installation of the Octagonal poles shall be designed to withstand the maximum wind speed of 169 km/hr. The top loading i.e. area and weight of fixtures are to be considered to calculate maximum deflection of the poles and the same shall meet the requirement of BS:5649 Part VI 1982. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding of the pole shaft. The welding of the pole shaft shall be done by Submerged Welding process. All octagonal pole shafts shall be provided with the rigid flange plate of suitable thickness with provision for fixing 4 foundation bolts. The base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside. The welding shall be done as per process approved by Third Party Inspection agency. (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make) Pole Type BOP or equivalent-9030 Height 9m The materials of the pole as follows : Conforming to grade S355JO Conforming to grade S355JO, Base Plate :- Fe 410 Conforming to IS 226/ IS 2062, Foundation Bolts:- 6.8 Gr. As per IS 1367, Pole Sections:- The Octagonal Poles shall be in single piece with single longitudinal welding join, Galvanization :- The poles shall be hot dip galvanized as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 65 micron. The galvanizing shall be done in single dipping. Door opening:- The Octagonal poles shall have door of approximate 500 mm length at the elevation of 500 mm from the base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connection as approved by the Depts.. The door shall be flush with the exterior surface and shall have suitable locking arrangement. The pole shall be adequately strengthened at the location of the door compensate for the loss in section. There shall also be suitable arrangement for the purpose of earthing, Smart pack Junction box with 6 MCB & Terminals for mounting inside base compartment of Pole. Top Dia. :- (A/ 70, Bottom Dia.:- (A/ 155 , Sheet Thickness :- 3mm , Base Plate Dimensions :- (L x B x 260 x 260 x 16, Foundation Bolt Size :- (no. x dia.) 4 x 24 Dia, Pitch Circle Dia.:- (PC 250 Bolt Length:- 750, Projected Bolt Length :-125 Anchor plate thickness :- 4 mm , Pole Foundation :- The octagonal poles shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. Foundation:- The foundation shall be done with ( Earth work 2.04 cubic Meters.RCC 1:1.5 : 3 proportion 0.65 cubic metres. Steel 22.43 Kg. Shuttering 4.32 square metres. = 22.43 Kg.
6
-
10
Supplying including fitting and fixing of Hot Dip galvanised arm bracket for installation of luminaries. Header with top cap 300 mm long pipe of thickness 3 with arrangement to fix on pole top with 3 Nos. of bolts. i Armed of required length size 48.3mm out side dia x 3.25mm thick (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make) Stiffener plate from arm of the following types : Single arm bracket 1000mm long for 3m to 10 metre. Poles.
6
-
10
Supplying and fixing of Fan box (AKG or equivalent as approved by the Deptt.)with inbuild rod as required.
6
-
10
Supply, Installation antistatic rubber mat suitable for 1.1 KV Voltage grade
4
-
10
Supplying including installation, testing and commissioning of Air/Water Cooled Diesel Generator set coupled to suitable alternator of 220/415 V, AC, 1/3-Phase 0.8 p.f.(la mounted on a 1) M.S. Fabricated base frame.,2) M.S. fuel tank of required capacity.,3) Residual Silencer.,4) Standard Control Panel.5) Suitable batteries with lead.,5) First fill of lube oil.,6) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the Technical Specification.. as per manufacturer. (RANGE FROM 5 KVA TO 625 KVA) Kirloskar green/bliss, Leyland, Volvo Penta, Perkinson, Mahindra, Greaves, Escort engine and Kirloskar, Stamford, Leroy somer alternator. KVA- PHASE- Approx size- Approx Wt - COOLING. 100 - 3 -3200x1300x1805 -1950 Kg -WATER CoolIed
1
-
10
100 KVA SUBSTATION: Shifting, reinstallation and commissioning of the following capacity outdoor type sub-station complete with transformer. HT/LT side fittings and all other accessories complete and considering of the following. The cost of fencing and transformer pad will be extra. a)100 KVA,11/0.433 KV, vector group DYN-11 aluminium wound transformer - 1No. b)11 KV DO Switch - 1 Set, c)MS Channel of size 100 mm x 50mm x 6mm x 2.2 mtrs. - 6 Nos. d)11KV Lightning arrestor - 1 Set, e)11 KV Pin type Insulator - 6 Nos. f)LT Cross arm,g)100 mm dia GI Pipe for pipe earthing - 6 Nos. g)11 KV Disk insulator 6 Nos. i)Hardware fittings for Disk insulator 12 Nos. j)Gang operated Switch - 1 set k)11 KV Danger Board 2 Nos. l)410 SP 56 Length of pole = 11.00 metre., Length of sections, Bottom = 5.60 M, Middle = 2.70 M, Top = 2.70 M, Out side dia. & Thickness Bottom = 193.70 x 5.40 mm, Middle =165.10 x 4.50 mm, Top =138.70 x 4.50 mm (193Kg)
1
-
10
Load security deposit to be deposited to concerned Power Supply Agency with check meter as well as permission from Power Supply Authority including liasioning with all the concerned departments etc..
70
-
10
Construction of 3 phase 11 KV Line on G.I. steel tubular pole 12m SP-62 using AAA Raccoon conductor 7/3.81mm with T cross arm average span 70m.
0.4
-
10
Supervision Charges and Liaision Charges to be paid to Power Supply Agency
1
-
10
HVAC For Auditorium
-
-
-
Supply,installation,testing and commissioning of VRF units complete with Twin Rotary/Scroll type compressors, special pre coated fins,panel,corrosion resistant coated condenser, condenser fan having interconnected control wiring housed in compact housing, refrigerant & Oil charging, MS hot dip galvanised suitable size stands for ODU,electrical & microprocessor panel,isolating valves and all required acessories for proper functioning of units,suitable to operate on 440 +10% volt,50Hz,3 phase- AC power supply of the the following capacities.(Unit of Cooling only should be supplied) (Make-Mitsubishi/Toshiba/O-General/Daikin/Carrier). ODU - 8.5TR
6
-
10
Supply, Installation, Testing and Commissioning of Floor mounted/Ceiling suspended, Sheet Metal Sectionalised Construction double Skin air handling unit with 25 mm thick injected PUF of density not less than 40 kg/cu/m. The AHU shall be complete with pre filter section with synthetic fibre filters and MERV-13 & MERV 8 filter, coil section with multiple rows deep Dx Cooling coil copper tube & Alminium fin construction, fan section complete with forward curve fan suitable for total static pressure as detailed below, 8 Row Deep Copper Coil, EFF-1 suitable squirrel cage induction motor, belt drive package, insulated stainless steel drain pan and vibration isolation arrangement all complete as per specifications. AHU's shall be seltected for a maximum face velocity of 400 FPM and Fan outlet velocity should not exceed 2000 FPM. The unit shall be supplied with EEV (Dx) and shall be including thermostats, control kit, control wiring & All accessories as required for completing the installations of following design parameters: (Make:- Zeco/ Edge Tech/Trane/Stulz/Humidin/CarryAir/Waves). 6000 CFM with 90 mm static pressure
3
-
10
Supply, installation, testing and commissioning of Corded Remote Controller with PCB for controlling AHU with ODUs
3
-
10
Providing and laying of control wiring PVC insulated of 3C X 1.5 sq. mm copper conductor shielded flexible cable in 25 mm PVC conduits between outdoor,indoor and remote control unit etc as required at site.
125
-
10
Supplying, installing, testing and commissioning of air-cooled direct expansion type ductable unit with Scroll Compressor complete with indoor and out door units suitable for 415 + 10% for outdoor and 230 + 5% volts for Indoor units ,50Hz AC power supply , control valves, copper piping, including fully charged with refrigerant R410A to outdoor unit ,valves. Quoted price shall include cost of wired remote controller, thermostat to display and control of temperature, wiring, control cable, MS stand for placing outdoor unit with rubber pad isolator & earthing. Unit shall be provided with auto timer setting, complete as per technical specifications.(Make-Mitsubishi/Toshiba/O-General/Daikin/Carrier). 5.5 TR
4
-
10
Supply, fabrication, installation, testing of Interconnecting refrigerant pipe work duly insulated with closed cell elastomeric nitrile rubber type tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger/tie rod .All refrigerant piping shall be protected with Woven Fiberglass cloth, 7 mil thickness and 200 gsm weight, with factory laminated, self-adhesive backing duly finished with 2 coats of UV painting etc complete as required. 28.6 mm OD With 19 mm insulation-
85
-
10
15.88 mm OD with 19 mm insulation -
85
-
10
19.1 mm OD With 19 mm insulation-
50
-
10
9.5 mm OD with 19 mm insulation -
50
-
10
Supply, installation, testing and commissioning of Rigid heavy class CPVC piping with minimum 9 mm nitrile rubber insulation over the pipes complete with fittings, supports, U trap arrangement, clean plug and accessories etc complete as required. 50MM Dia
65
-
10
25MM Dia
50
-
10
Supply, installation, testing and commissioning of fire proof Canvas connections etc as required.
5
-
10
Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vances, hangers, supporters etc. as per specifications of following sheet thickness complete as required. 24 Gauge
445
-
10
22 Gauge
261
-
10
Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc., as per specifications.
6
-
10
Supply and installation of supply air jet nozzle with dampers in extruded aluminium construction and powder coated etc as required as per site. Jet Diffuser With 300 mm Dia
35
-
10
Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core
10
-
10
Supply and Fixing of 19 mm thick thermal insulation for SA/RA duct of mat finish Closed cell Nitrile Rubber (Class "O") Insulation duly laminated with aluminium foil. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive insulation tape complete as per specification and as required of following
706
-
10
Supply and installation of motorised fire and smoke dampers in return air path of conditioned area.
10
-
10
Supplying and fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.
45
-
10
Supplying, fixing acoustic lining on wall and ceiling of AHU rooms with 50 mm thick, density 32 kg/cu.m resin bonded glass fiber insulation friction fixed in 610 mm x 610 mm frame work made of 25X50X50X50X25 mm made out of 0.6mm thick GI sheet U shaped channel and covered with reinforced fiber glass tissue and finished with 0.80 mm perforated aluminium sheet etc. complete as required and as per specifications.
75
-
10
Supply, installing, testing and commissioning of wall / ceiling mounted air cooled SPLIT AIR CONDITIONING UNITS as per specifications. The unit shall be complete with Copper tube aluminium Fins, both indoor and outdoor units, in-built stabilizer, condensate drain pan, piping, control valves and insulation, power wiring, thermostate, control wiring, earthing, MS structural support for condensing unit with vibration isolator pad complete in all respects of following capacity.(Make-Mitsubishi/Toshiba/O-General/Daikin/Carrier). 2.0 TR High Wall type Split Unit (3 Star Rated)
4
-
10
Supply, installation, testing and commissioning of mix flow in-line fans comprising of Class I construction complete with TEFC induction motor fitted with ball type bearing, suitable for operation on single phase, 220 volts, 50 Hz supply complete with DP MCB in MS box including connection of fan with required 3 core copper cable from DP MCB box complete as required at site. 600 CFM (Static Pressure 20mm of water, Maximum)
2
-
10
Fan Section: Supply, installation ,testing and commissioning of wall mounted cubical type DOL starter panel, fabricated from 2.0 mm thick CRCA Sheet duly powder coated of suitable size , internally Wired, operate on 415 Volts, 3- Phase, 4 Wire, 50 Hz AC power Supply system having suiatble rating aluminium bus bar ,suitable mounting arrangement and comprising of following accessories. a)63 Amps TPN MPCB-1 No. (Incomer), b)DOL Starter Suitable for up to 7.5 HP for AHU Motor (comprising of contactors of relevant rating)-1 set, c)Thermal overload relay, electronic timer - 1 No. Each, d)Single Phase preventer - 1 No. e) ON/OFF/TRIP Indication lamps-1 set, f)Start/Stop push button -1 set. g)Phase indication lamp-1 set, h)Digital Ammeter & voltmeter - 1 No. each with ASS with suitable CT's of class 1.0 VSS and MCB's of suitable rating.
3
-
10
63 Amps TP MPCB With Weather proof isolation boxes for power supply to outdoor unit of Dx type ductable unit i/c connections etc complete as required.
10
-
10
Suppling.laying,testing and commissioning of following sizes of 1.1KV grade armoured FRLS,PVC insulated PVC sheathed COPPER conductor cable conforming to relevant and ammended indian standards laid on existing wall surface i/c clamping, end termination complete as required. 4Cx10 sqmm
120
-
10
3.5x 35 sqmm
65
-
10
3.5x 50 sqmm
85
-
10
AUDIO SYSTEM For Auditorium
-
-
-
Powered Dual 8" LF Driver and 3" Compression Driver Line array speaker, Frequency range - 8C6:C90Hz-20 kHz, 110 Deg Horizontal X 12 Deg Vertical Dispersion, 136 dB SPL, weight 20 Kg . Make-JBL By Harman
12
-
10
Suspension Bar Kit for above line array loudspeakers, Suspension bar kit should be made by same speaker OEM, Should have powder coating . Make-JBL By Harman
3
-
10
Powered Dual 15" Woofer, Frequency Range 32 Hz - 250 Hz, 136 dB SPL, Built in DSP with crossover management, EQ, Limiting, integrated Amplifier to power 4 tops, weight 86 kg. Make-JBL By Harman
3
-
10
12" Self-Powered Stage Monitor Loudspeaker System having SPL of 127 dB peak, Frequency Range= 50 Hz – 20 kHz, Class- D 1300W amplification, Coverage Pattern 100° x 60° nominal, Bluetooth app control to select the user preset, Crossover Frequency: 2 KHZ, User selectable presets for Main or Monitor position, Powder coated Grill, 100V - 240V ~ 50/60 Hz Operation, 2 XLR Combo Jack / Bluetooth / 1 XLR M Thru Jacks, Weight 14.6 Kg. Make-JBL By Harman
3
-
10
Two Way Compact Loudspeaker having 8" LF Driver & 1" Tweeter driver, 300W Continous program Power, Coverage Pattern = 110° x 85°, Frequency Range = 45 Hz - 18 kHz , SPL of 120 dB, System Sensitivity: 90 dB SPL/1W/1m. Make-JBL By Harman
4
-
10
Wall Mount Bracket for Two way compact loundspeaker
4
-
10
Two Channel Power Amplifier with Power output 2 x 775W @ 4 Ohms and 2400W at 4 Ohm Bridged mode, Selectable input sensitivity 1.4 Vrms / 0.775 Vrms, Class D Amplification, DSP inbuilt, LED indicatiors, Remote Power Trigger capability, Integrated Pureband crossover System. Make-CROWN By Harman
1
-
10
Two way Wall Mount Loudspeaker, 2-way loudspeaker system with 200W peak Power rating, Coverage Pattern = 100° x 100°, Frequency Range =75 Hz to 19.5 kHz, SPL =109 dB peak. Make-JBL By Harman
2
-
10
Two Channel Power Amplifier with Power output 2 x 350W @ 4 Ohms and 1100W at 4 Ohm Bridged mode, Selectable input sensitivity 1.4 Vrms / 0.775 Vrms, Class D Amplification, DSP inbuilt, LED indicatiors, Remote Power Trigger capability, Integrated Pureband crossover System. Make-CROWN By Harman
1
-
10
Wired Gooseneck Microphone with Desktop base unit and on/off switch for Podium & Dias Use, Audio frequency bandwidth =70 - 18000 Hz , Signal to Noise:64 dB-A, Length =500 mm, Voltage =9 to 52 V Power Interface. Make-AKG / CROWN By Harman
2
-
10
Wireless Handheld Microphone System, Working Range: 10m, Frequency Response:70 Hz–20 KHz,Signal-to-noise90 dBA
Battery Life 12 Hours. Make-AKG By Harman
4
-
10
Wireless Lavalier Microphone System, Working Range: 10m, Frequency Response:20 - 20000 Hz, Signal-to-noise57 dB-A, Battery Life 12 Hours. Make-AKG By Harman
1
-
10
Wired Dynamic Vocal Microphone ,Super cardioid vocal microphone Audio frequency bandwidth :70 - 20000 Hz, Sensitivity2.6 mV/Pa. Make-AKG By Harman
4
-
10
Wired Instrument Microphone, Cardioid microphone Audio frequency bandwidth : 50 - 20000 Hz, Sensitivity 2.6 mV/Pa . Make-AKG By Harman
4
-
10
24 Channel Analog Mixer having atleast 16 Channel Mono Input, 48V Phantom Power, Stereo Inout Channel with equilizer. Make-SOUNDCRAFT By Harman
1
-
10
Control Room head phone for FOH Monitoring Professional studio grade closed-back headphones with auto mute technology, Max. Input Power =200 mW, Audio frequency, bandwidth=16 - 28000 Hz , Sensitivity headphones =104 dB SPL/V, Should have Detachable cable. Make-AKG By Harman
1
-
10
Loundspeaker Management having 3 Input 6 Output Processor. Make-dBx By Harman
1
-
10
Active Direct Box with 1 instrument/line/speaker level input, Frequency Response 20Hz to 20kHz, +/-2.5dB, input connector 1/4" jack, input type unbalanced, RF filtered, Impedance 150k Ohm typical, Max Input +20dBu (0dB pad); +40dBu (20dB pad); +60dBu (40dB pad), Output (Thru) 1 parallel from input jack, 1/4" Unbalanced, RF filtered, Noise -105dB unweighted, 22kHz BW, THD 0.01%, 20Hz to 20kHz BW; 0.005%, 1kHz. Make-dBx By Harman
1
-
10
Audio Equipments Cables & Connectors Like Speaker Cable, Microphone Cable, RCA Connectors, Speakon, XLR Connectors as required
1
-
10
Audio Equipment rack with standard accessories like fan, PDU, Shelf etc as required. Make-Nettrack
1
-
10
MS Structure for Hanging & Mounting the speakers
1
-
10
UPS 10 KVA with isolation Transformer with external battery backup of 15 mins for Audio System. Make-Delta
1
-
10
VIDEO SYSTEM For Auditorium
-
-
-
WUXGA (1920 X 1200) resolution Laser Projector having 7000 Lumens with standard Lens, supporting aspect ratio of 16:10, Contrast ratio of 3000000:1, Ligth Source - Laser. Make-Benq / Panasonic
1
-
10
Projector Mount . Make-CUSTOM
1
-
10
4 Port Input & 1 Port Output HDMI Switcher. Make-Wyrestorm / Aten / Impression
1
-
10
1 Port Input & 8 Port Output HDMI Splitter. Make-Wyrestorm / Aten / Impression
1
-
10
HDMI over CAT6 extender supporting UHD Resolution 40 Mtrs Transmitter Module. Make-Wyrestorm / Aten / Impression
2
-
10
HDMI over CAT6 extender supporting UHD Resolution 40 Mtrs Receiver Module. Make-Wyrestorm / Aten / Impression
6
-
10
Audio Dembedder from HDMI Signal. Make-Wyrestorm / Impression
1
-
10
Face Plate with HDMI / Aux / Lan. Make-Wyrestorm / Impression
2
-
10
55" Panel with normal beezel to beezel having brightness of 300 cm/m2. Make-Lg / Samsung
2
-
10
Cables for Video Equipments like HDMI, RCA, CAT6 etc with pvc conduit as required
1
-
10
Laptop having Core i3 processor, 8 GB Ram, 500 GB HDD, wifi. MakeLenovo
1
-
10
Networking 8 Port Gigabit Switch of 10/100/1000 Mbps. Make-HP Aruba / Netgear
2
-
10
STAGE LIGHTING For Auditorium
-
-
-
Par-64, 1000w , 240volt shielded beam available in three version i.e. sopt ,flood and wide flood, (GE/Philips)colour,temperature 3200k Base - extended Modul end Prog,Housing CRC sheet metal matt black finish with sufficient ventilation,with 2 mtr, 3 core wire,plug,Clamps.Make-DLMC
24
-
10
Led Profile spot ULTRA BRIGHT Specification Voltage : AC90-240V, 50/60Hz Power Consumption : 200W LED : 200W Warm White / 2 in 1 / 4 in 1, Service Life : 60000 hours Lens Angle : 19/26/36° Optional Dimmer : 0-100% Linearly Adjustable Ambient Temperature : -25°C -+45°C Control Signal DMX512,Master-Salve, Sound, AutoControl Channel : 1/3CH (Single colour), 2/5CH (2in1)N.W 6 kg, G. WSKG Dimensions : 450*280*mm Packing Size : 650*300*300mm. Make-DLMC
5
-
10
Spot light 1000watt 240v Halogen lamp T-11 type Reflector Spherical,Anodized finish,Lens Plano Convex
Lens 150mm Dia, Housing CRC sheet, Color Black, Focusing Front/Back/Rotary Knob, 2 mtr. 3 core wire ,
plug top.(Lamp:-GE/Philips).Make-DLMC
12
-
10
LED cyclorama light Light source : 18PCS 12W 4IN1 LEDs Lens angle : 25o(30o, 45o, 60o optional) Channel mode : 3 / 4 / 6 / 7 / 9DMX channel mode 0-100% linear dimmer Function: color mix, automatic color change, built-in program and strobe effect with adjustable speed Sound controlled via built-in microphone Adjustable sound sensitivity
LED Display, easy to control Control : auto, sound active, DMX512, software(connect to computer) Overheating protection Voltage : 100-220V,50/60hz Power : 230W IP rating : IP20(PLS-18 x 4in 1). make-DLMC
6
-
10
LED par 54 LED Par 200w, voltage-110v-250v/50-60HZ,lamp-TX high power LEDS; 3w x54 LED,(R 14pcs;G14pcs;B14pcs ;W12pcs) working position; any safe working position LED display, channel-4/5/7 CHS,Beam Angle-15/25/45/600 ,IP Grad-IP20,control mode- master/slave synchronization, DMX-512 control and auto matic run funcation, construcation-Aluminium and plastic body,silver,white and black optional,WITH ip 20(PLS- PL-5403 INDOOR). Make-DLMC
28
-
10
Moving Head Light Sharpy 7RD ,Bulb：MSD Platinum 10R (life:2200 hour ,color temperature: 8000K)；Pan scanning：540°(16bit precision scanning) electronic error correction；Tilt scanning：270° (16bit precision) electronic error correction ; Color plate:1 color plate，14 color sheet per color plate；Gobo wheel:1 Gobo wheel,17 Gobo Effect wheel: bi-prism self-rotatione; effect moving,Atomization function； 0—100% machine dimming, support mechanical flash and adjustable speed flash effect, support flash macro function, lens optics system,power-driven focus,beam angle 0-4 degree, Over-heat protection； Voltage：100-240V，50/60HZ； Power：400 W, IP protection rate:IP20. Make-DLMC
6
-
10
Light Controller Computer Light Controller,Product Model PLS
Stone 2048 Voltage 100 to 240 V Frequency 50/60 Hz internal flash driver, 10 similar in functionality to a hard dist but faster and ore rugged. Cache the entrire Fixture library of more then 3000 files, 240 intelligent fixture,240 dimmer control chanel, 15 master Play Back controlling and 450 Memories.Make-DLMC
1
-
10
LED Cob24 (4in1) Light 250w RGBW 8w Each x 24 LED, 80* reflector, Die-casting aliminium housing silver, white,black ect optional master slave synchronization, DMX 512 control, Auto run, 0-100% liner dimmer, no noise, quite working whiout heating problem super even mixing colour with COM 4in 1 LEDs for cyclorama. Make-DLMC
8
-
10
Fresnal light 1000 watt/ 240v T-11 type with Brandoor,Reflector Spherical,Anodized finish,Fresnal Lens 150mm Dia,Housing CRC sheet,,Color Black,Focusing Frount/Back/Ratary Knob,2 mtr. 3 core wire , plug top. Make-DLMC
8
-
10
Wall Mount Dimmer 12 Ch with Patch Panel , 4 Kw 12 Ch. Make-DLMC
1
-
10
Haze Machine With Haze Liquid 2 Jars. Make-DLMC
1
-
10
Lighting Cables like Electrical cables, DMX cables, Cat6 Cables in pvc conduit / casing as required
1
-
10
Light socket box 4"x4" with 15 Amp multi socket
98
-
10
MS Structure for Hanging & Mounting the Lights
1
-
10
DMX Splitter 1 in 10 out. Make-DLMC
2
-
10
Furniture For Auditorium
-
-
-
Push Back Auditorium Chairs with maximum lumbar support for fatigue free healthy seating, engineered for ergonomic shape, environment friendly, Molded Polyurethane foam cushioned seat back, Upholstered with Scothgard for Stain Resistance, Integrated skin type PU foam made arm rest without cup holder, Maintenance free Synchronized Push back system, with seamless seat supporting tray, Heavy gauge CRC Sheet made side stand covered with fabric, Chairs installed to the floor with expanded anchor fasteners complete is all respect(Normal). Make-CUSTOM
283
-
10
Make:Godrej Model:Glamour NXT High Back Auditorium Chair(VIP)
18
-
10
Main curtain motorised curtain control system with horizontal sliding arrangement complete with fixing, Rails, brackets, sliding arrangement & motorised operation complete with runners, master runners, pulleys 3-mm steel wire rope, 1HP motor(Compton) 2nos. Air breaker contactors (L&T) 2nos., micro switches for auto stop, 3nos push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed ,stiched in double gathering. Make-CUSTOM
1
-
10
Cloth wings made out of black glazed cotton cloth on one side of MS 50mm x 25mmx 16G pipe wielded frame work. The pipe framework made out of 25mm x 50 mm pipe. fixed with overhead pivote track complete with duly painted on both framework. Make-CUSTOM
8
-
10
Cyclorama curtain with PVC perforated screen. The screen to be fixed on tubular frame made out of 32mm dia MS pipe. Make-CUSTOM
1
-
10
Frill Bars, fixed type made of 25mm GI pipe, supported from Ceiling structure, as required, high quality Frill to be made out of Black Glazed Cotton Cloth, stitched with pleats, frills, etc. Make-CUSTOM
3
-
10
Carpet For Auditorium
-
-
-
Solid Teak Flooring have 18 mm thickness, Cut in 93 mm width with water based PU polish with necessary scres & side beat. Make-CUSTOM
190
-
10
Carpeting of entire stair area where chairs will be installed in lower balcony & upper balcony area with 1-2 mm inner lay below carpet. Make-CUSTOM
775
-
10
ACOUSTIC WALL PANELING AND CEILING For Auditorium
-
-
-
Supply and installation of Fabric Covered Heradesign fine wood wool panel ( Made in Austria ) of size 1200 x 600 x 25mm mounted on supplied G I Frame work consisting of basic profile, main profile & edge profile.The woodwool panel will be back lined with 50mm thick 1; Frame work consists of 25mm thick GI wall channels with fully knurled surface of 0.55mm thick 80mm width, having two equal flanges of 26mm. A GI wall channel is fixed to the walls in horizontal direction with the help of suitable fastners at 600mm C/C then an another 25mm thick GI wall channel is fixed vertically over the horizontlly laid wall channel at 600mm C/C . The frame work shall be back lined by using polyester wool having a density of 1000 GSM and 50mm thick. (Upper Portion)
253
-
10
Supply and installation of FR grade 150mm wide 12mm thick Laminated plywood (150mm wide slat and 3mm gap between 150mm wide plywood) backed with 50mm thick 1000GSM polyester wool. Frame work consists of 25mm thick GI wall channels with fully knurled surface of 0.55mm thick 80mm width, having two equal flanges of 26mm. A GI wall channel is fixed to the walls in horizontal direction with the help of suitable fastners at 600mm C/C then an another 25mm thick GI wall channel is fixed vertically over the horizontlly laid wall channel at 600mm C/C . The frame work shall be back lined by using polyester wool having a density of 1000 GSM and 50mm thick. 150 mm wide 12 mm thick Laminated plywood is fixed on to frame work and 3mm gap is maintained between 150mm wide plywood and length as per the drawing of approved finish and then fixed to GI frame work by using suitable fasteners and ensure proper level of the panel surface.(Lower Portion)
100
-
10
Supply and installation of Heradesign Fine wood wool panel ,factory painted, ( Made in Austria ) of size 1200 x 600 x 15mm mounted on proprietory supplied G I Frame work consisting of basic profile, main profile,edge profile and spacer.(Stage Side & Rear)
252
-
10
Supply and installation of 12.5mm thick plain gyspum plaster board Suspended by using C System which includes Main channel at every 1200mm . The gypsum plaster board will be backed with 50mm thick 1000GSM Polyester Wool to achieve NRC of minimum 0.75. Frame work shall consists of GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm) fixed along with perimeter of the gypsum or walls with the help of nylon sleeves and screws at 600mm c/c. Then suspend GI main channels of size 45 mm (0.9mm thick with 2 flanges of 15mm each) from the soffit at 1200mm c/c by using soffit angle of size 25mm x 10mm x 0.55mm thick fixed to true ceiling by using suitable fasteners. Cross channels of size 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the main channel with the help of connecting clips and in a direction perpendicular to the main channel at 300mm c/c. The Gypsum board will be painted as per selected colour and shade.(Main Ceiling)
269
-
10
Supply and installation of (12mm square perforations) Perforated gypsum plaster board backed with 50mm thick 1000GSM Polyester Wool to achieve NRC of minimum 0.75 : Frame work shall consists of GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm) fixed along with perimeter of the gypsum or walls with the help of nylon sleeves and screws at 600mm c/c. Then suspend GI main channels of size 45 mm (0.9mm thick with 2 flanges of 15mm each) from the soffit at 1200mm c/c by using soffit angle of size 25mm x 10mm x 0.55mm thick fixed to true ceiling by using suitable fasteners. Cross channels of size 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the main channel with the help of connecting clips and in a direction perpendicular to the main channel at 300mm c/c .(Main Ceiling)
256
-
10
Sports Badminton Section for Indoor Stadium
-
-
-
Maple Wood Flooring. Make-Vinayak
774.26
-
10
LED Light. Make-Philips
54
-
10
Net (Younex). Make-Yonex
6
-
10
Net Pol. Make-Yonex
6
-
10
Acoustic Sound. Make-Armstrong
639.62
-
10
Younex Mat
6
-
10
Sports Table Tennis Section for Indoor Stadium
-
-
-
Floor Mate. Make-Vinayak
300
-
10
LED Light. Make-Philips
60
-
10
Table tannis board Donic
6
-
10
Furniture For Indoor Stadium
-
-
-
METAL LOCKERS FOR -12 UNITS Body .8mm Thick & Door 1mm With lock Thick Powder coated 45-60 microns.SIZE-2100X550X1500. Make-Vinayak
4
-
10
WARDROBES FOR CHANGING ROOM-6 UNITS Body .8mm Thick & Door 1mm With lock Thick Powder coated 45-60 microns.SIZE-1950X450X900. Make-Vinayak
8
-
10
Locker room benches come in a variety of styles and sizes to suit your locker room needs. Whether in Aluminum Frame Bench or Hardwood Locker Room Benches.L1200 x D300 x H450 L1500 x D300 x H450. Make-Vinayak
4
-
10
Office Executive desk with side runner and Mobile pedestal-size-1800X900X750. Make-Vinayak
4
-
10
Officer Executive Revolving Chair .Make-Vinayak
4
-
10
3 Door Filling Cabinet make with 3 layer pre laminated particle baord. Make-Vinayak
4
-
10
Maintanance For Auditorium
-
-
-
Operation and Maintanance Cost (Year-Wise) after completion of work. Including Civil Work, Electrical Work, Air Conditioning, Pumps, DG Sets, Sub Station, Fire Alarm, Fire Fighting, Lifts etc. a) First Year
1
-
10
b) Second Year
1
-
10
c) Third Year
1
-
10
Maintanance For Indoor Stadium
-
-
-
Operation and Maintanance Cost (Year-Wise) after completion of work. Including Civil Work, Electrical Work, Air Conditioning, Pumps, DG Sets, Sub Station, Fire Alarm, Fire Fighting, Lifts etc. a) First Year
1
-
10
b) Second Year
1
-
10
c) Third Year
1
-
10
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements