Brahmaputra Valley Fertilizer Corporation Limited Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 25,000Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2023_BVFCL_153297_1Bid Award Id
ViewTender No
CE/2023/SPC/03Tender Authority
Brahmaputra Valley Fertilizer Corporation Limited ViewPurchaser Address
-Website
http://etenders.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
Annual rate contract for Civil maintenance works in Sector A B and Fof BVFCL Township for 12 months.
Annual rate contract for Civil maintenance works in Sector A B and Fof BVFCL Township for 12 months.
BOQ Items
Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.50m
115
-
-
Supplying & filling in plinth with river sand under floors including watering, ramming, consolidation and dressing complete
1
-
-
Supplying and stacking of sandy gravel in measurable stack and then spreading at working watering, ramming, consolidation and dressing complete as per the direction of Engineer-In-charge.
3
-
-
Surface dressing the ground including shallow earth work upto 15 cm depth including removing vegetation and inequalities in all kinds of soils including disposal of rubbish lead upto 50M and lift upto 1.50M.
35
-
-
Engazement of Mechnical excavator ( Tyremounted) with bucket capacity of 0.30 CUM including the cost of fuel, lubricant, driver & helper.
4
-
-
Mechanical carriage of excavated earth, dismantled building materials, grasses, shrubs and other rubbish including loading, unloading and stacking / spreading at designated site within Township area - 20% void shall be deducted.
9
-
-
Dismantling RCC works including stacking of reclaimed MS reinforcement & disposal of unserviceable materials up to a distance of 50 M lead outside the periphery of area cleared
0.5
-
-
Dismantling CC works including disposal of unserviceable materials up to a distance of 50 M lead outside the periphery of area cleared
7
-
-
Dismantling brick work manually / by mechanical means in cement mortar including stacking of serviceable materials and disposal of unserviceable materials upto a distance of 50 m lead as per the direction of EIC.
9
-
-
Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 m lead
6
-
-
Removing mortar and cleaning bricks including stacking within a lead of 50M (stacks of cleaned bricks shall be measured)
880
-
-
Providing & laying in position specified grade of cement concrete excluding the cost of centering, shuttering - all work upto plinth level CC 1:2:4 (1 cement : 2 river sand : 4 stone aggregate 20 mm nominal size)
0.5
-
-
Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement - 1:2:4 (1 cement : 2 river sand : 4 stone aggregate 20 mm nominal size)
3.65
-
-
Providing and laying in position cement concrete of specified grade CC 1 : 3 : 6 ( 1 Cement : 3 river sand : 6 Stone aggregate 20mm nominal size) excluding the cost of centering & shuttering - All work upto plinth level
0.5
-
-
Providing and laying in position cement concrete of specified grade CC 1 : 4 : 8 ( 1 Cement : 4 river sand : 8 Stone aggregate 40 mm nominal size) excluding the cost of centering & shuttering - All work upto plinth level
0.5
-
-
25 mm cement concrete flooring 1:2:4 (1 cement : 2 river sand : 4 stone aggregate 12.50 mm nominal size) finished with a floating coat of neat cement .. May be used as plinth protection & foot path
260
-
-
Extra for making chequres of approved pattern on cement concrete floors, steps landings & pavement etc.
1
-
-
Reinforcement for RCC work including bending, binding and placing in position complete
280
-
-
Labour rate for reinforcement for RCC work including bending, binding and placing in position complete-
11
-
-
Providing & fixing up to first floor level precast reinforced cement concrete 1:2:4 (1 cement : 2 river sand : 4 stone aggregate) including finishing and plastering with cement plaster 1:3 (1 cement : 3 local river sand) of thickness not exceeding 6 mm on exposed surface to give a smooth and even surface, excluding the cost of centering & shuttering and reinforcement : (a) Kerbs, steps, slabs and the like.
0.5
-
-
Centering and shuttering including strutting, propping etc and removal of form work for: (a) Foundation, footings, bases of columns etc. for mass concrete
5
-
-
Centering and shuttering including strutting, propping etc and removal of form work for:(b) Columns, piers, abutments, posts and struts
20
-
-
Centering and shuttering including strutting, propping etc and removal of form work for:(c) Lintels, beams, plinth beams, girders, bressumers and cantilever
10
-
-
Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand
etc. all complete as per the direction of Engineer-in-charge
270
-
-
Pucca brick work in foundation and plinth using common burnt clay local best quality bricks in cement mortar 1: 6 (1 cement : 6 river sand) including curing etc. complete
1
-
-
Extra for brick work with local best quality bricks in superstructure above plint & up to floor 5 level in all shapes & sizes in cement mortar 1: 6 (1 cement : 6 river sand) including curing etc.
0.5
-
-
Half brick masonary with local best quality bricks in superstructures above plinth level upto floor five level in cement mortar 1: 4 (1 cement : 4 river sand).
60
-
-
Labour rate for half brick masonary with local best quality bricks in superstructures above plinth level upto floor five level in cement mortar 1: 4 (1 cement : 4 river sand).
15
-
-
12 mm cement plaster of mix 1 : 6 (1 cement : 6 river sand) at all height . .
15
-
-
15 mm cement plaster of mix (a) 1 : 6 (1 cement : 6 river sand) at all height
15
-
-
Neat cement punning at all height . .
50
-
-
Carriage of cement filled 50 kg. bag from BVFCL store to different working sites within township area.
1
-
-
Supply of oridinary/puzzolona portland cement in 50 Kg. HDPE bags to township maintenance store.
1
-
-
Repairing of RCC chajjas & parapet walls etc. with 12 mm cement plaster of mix 1:4 (1 cement : 4 river sand) with a floating coat of neat cement including preparation of surface at all height as per the direction of EIC .
5
-
-
Repairs to plaster of thickness 12mm to 20mm in patches of 2.50 sqm & under including cutting the patch in proper shape and preparing and plastering, finishing of walls complete including the surface rubbish to the dumping ground as per the direction of Engineer-In-Charge (a) With cement mortar 1:4 (1 cement : 4 river sand).
180
-
-
Providing and fixing 1st quality ceramic glazed wall tiles (300x200) mm confirming to IS : 15622 (Thickness to be specified by the manufacture of approved make in all colours, shades, except burgundy, bottle green, black of any size as approved by EIC in skirting, riser of steps and dado over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 river sand) and joining with grey cement slurry @ 3.3 Kg per sqm including pointing in white cement mixed with pigment of matching shade complete.
1
-
-
Providing & fixing available 1st quality ceramic glazed floor tiles(300x300) mm (Thickness to be specified by the manufacture) of 1st quality confirming to IS : 15622 of approved make in colours such as white, ivory, grey, fume red, brown laid down of 20 mm thick cement mortar 1:4 (1 cement : 4 River sand) including pointing the joints with white cement and matching pigment etc. complete.
1
-
-
Dismantling of wooden / MS doors, windows and clerestory windows shutters of area 3 Sqm. & below including frames; hold fast etc. complete and stacking of serviceable materials and disposal of unserviceable materials up to Township maintenance store (a) Of area 3 sqm and below
65
-
-
Dismantling of wooden / MS doors, windows and clerestory windows shutters of area 3 Sqm. & below including frames; hold fast etc. complete and stacking of serviceable materials and disposal of unserviceable materials up to Township maintenance store(b) Of area beyond 3 sqm
1
-
-
Taking out doors, windows and clerestory window shutters (Steel or wood) of area 3 Sqm & below including stacking at our store (a) Of area 3 sqm and below
75
-
-
Taking out doors, windows and clerestory window shutters (Steel or wood) of area 3 Sqm & below including stacking at our store (b) Of area beyond 3 sqm
1
-
-
Dismantling wood work in frames, trusses, purlins and rafters up to 10 M span and 5 M height of sectional area 40 Sq CM & above including stacking the materials at our store
0.5
-
-
Providing wood work in frames of doors, windows, clerestory windows and other frames, wroughed frame of locally available best quality wood and fixed in position
2
-
-
Labour rate for wood work in frames of doors, windows, celetory windows and other frames wroughed, framed and fixed in position- :
0.1
-
-
Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position
0.5
-
-
Labour rate for wood work in frames of false ceiling, partitions etc. sawn and put up in position Required wood shall be arranged by BVFCL on free of cost basis.
0.1
-
-
Providing & fixing MS round or square bars at required spacings in wooden frame of windows and clerestory windows
10
-
-
Providing & fixing 15 mm GI pipes of approved quality with fittings and clamps as curtain rod including cutting etc complete in all respect
1
-
-
Labour rate for fixing provided curtain rod with brackets, wooden plugs etc. where ever required.
1
-
-
Providing and fixing 40 x 3 mm flat iron hold fast 30 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedded in cement concrete block 30 x 10 x 15cm with cement concrete of mix 1 : 3 : 6 (1 cement : 3 river sand : 6 stone aggregate 20mm nominal size)
1
-
-
Providing and fixing 40 x 3 mm flat iron hold fast 20 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedded in cement concrete block 30 x 10 x 15cm with cement concrete of mix 1 : 3 : 6 (1 cement : 3 river sand : 6 stone aggregate 20mm nominal size)
200
-
-
Supplying MS Bolts & Nuts with washer of different diameter as per site requirement
5
-
-
Providing and fixing ISI marked flush door shutters confirming to IS:2202 (Part-1), non decorative type , core or block board construction with frames of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneer on both faces of shutters including black enamelled iron hinges with necessary screws of: (i) 30 mm thick
10
-
-
Providing and fixing ISI marked flush door shutters confirming to IS:2202 (Part-1), non decorative type , core or block board construction with frames of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneer on both faces of shutters including black enamelled iron hinges with necessary screws of: (ii) 25 mm thick
1
-
-
Providing and fixing ISI marked 19 mm thick water proof block board door shutters confirming to IS including oxidised MS hinges with necessary MS screws.
34
-
-
Providing and fixing reputed brand & manufacturer 21 mm thick PVC door shutter along with PVC door frame including oxidised MS hinges with necessary MS screws.
26
-
-
Repairs to flush doors shutter or cupboard shutter by fixing 3 mm ply to the damaged portion of door with nails at 100 mm C/C & use of approved quality adhesive finished smooth complete in all respect as per the direction of Engineer-In-charge
5
-
-
Providing and fixing approved quality MS pressed butt hinges bright finished with necessary screws etc. complete:(a) 125 x 65 x 2.12 mm
1
-
-
Providing and fixing approved quality MS pressed butt hinges bright finished with necessary screws etc. complete:(b) 100 x 58 x 1.90 mm
80
-
-
Providing and fixing approved quality MS pressed butt hinges bright finished with necessary screws etc. complete:(c) 75 x 47 x 1.70 mm
40
-
-
Providing and fixing approved quality MS bright finished handle with necessary screws etc. complete:(a) 75 mm
50
-
-
Providing and fixing approved quality MS bright finished handle with necessary screws etc. complete:(b) 100 mm
100
-
-
Providing & fixing oxidised approved quality MS tower bolts with necessary screws etc. complete :(a) 100 x 10 mm
65
-
-
Providing & fixing oxidised approved quality MS tower bolts with necessary screws etc. complete :(b) 150 x 10 mm
100
-
-
Providing & fixing approved quality oxidised MS sliding door bolts with nuts & bolts etc. complete:(a) 250 x 14 mm
20
-
-
Providing & fixing approved quality oxidised MS sliding door bolts with nuts & bolts etc. complete:(b) 300 x 14 mm
2
-
-
Repairs to all types of wooden doors by fixing approved quality 0.35 mm thick aluminium plain sheet to the damaged portion of door with nails at 100 mm c/c finished smooth complete in all respect as per the direction of Engineer-In-charge.
40
-
-
Renewing approved quality glass panes with putty / wooden fillets and nails where ever necessary (a) 3 mm thick @ 7.50 Kg/Sqm
5
-
-
Renewing approved quality glass panes with putty / wooden fillets and nails where ever necessary (b) 4mm thick @ 10 Kgs/ Sqm
1
-
-
Renewal of old putty of glass panes (Length)
1
-
-
Labour rate for fixing available glass panes with putty, wooden fillets and nails & wooden panels in windows / doors / ventilators etc
1
-
-
Supplying & fixing new wooden fillets where ever necessary of local best quality wood
10
-
-
Labour rate for minor repairing of wooden doors , windows and ventilators like re-alignment of shutters, refixing of hinges etc. to make it free for operation as per the direction of Engineer-In- Charge (Repalced fittings & timbers shall be paid separately).
160
-
-
Providing and fixing 30 mm thick glazed shutters for doors, windows & clerestorty windows of local best quality wood using 4 mm float glass panes including black enamelled ISI marked MS butt hinges with necessary screws
20
-
-
Providing & fixing galvanised MS wire mesh of average width of aperture 1.40 mm with wire of dia 0.63 mm for doors and windows and clerestory windows including necessary wooden fillets, wire nails and also including removing the damaged / existing wire mesh.
1
-
-
Providing and fixing 30 mm thick wire gauge shutter using galvanised MS wire gauge of average width of aperture 1.40 with wire of dia 0.63 mm for doors and windows and clerestory windows including necessary wooden fillets, wire nails and also removing the damaged / existing wire mesh.
1
-
-
Providing & fixing 20 gauge 12 mm mesh galvanised wire netting above post plate with netting cane bead on existing frame including labour for removing the old wire netting etc. complete as per the direction of Engineer - In- Charge.
1
-
-
Providing and fixing oxidised MS Hasp & staple (safety type) conforming to IS :363 with necessary screws etc complete. a) 90 mm
2
-
-
Labour rate for fixing BVFCL's issued universal hydraulic door closer with necessary accessories and screws or nuts & bolts etc.complete
1
-
-
Labour rate for fixing BVFCL's supplied non- hydraulic door closer / spring with necessary accessories and screws or nuts & bolts etc.complete
1
-
-
Providing & fixing 12 mm thick and 100 mm wide ply pelmet with locally available best quality hard wood with bracket including fixing with 25 x 3 mm flat 10 cm long and pluge etc complete with necessary screws / nails
1
-
-
Construction of temporary urinal; of size 1.5 M x 3.0 M with jati bamboo post 1.5 M C/C with hessian cloth layer and tying with coir rope including digging holes etc. complete as per direction of EIC.
3
-
-
Providing & fixing cupboard shutter by fixing 3 mm ply over wooden frame with nails at 100 mm C/C & use of approved quality adhesive finished smooth complete in all respect as per the direction of Engineer-In- charge
7
-
-
Dismantling CGI roofing including ridges, hips valleys and gutters etc. and stacking the material within 50 M lead.
50
-
-
Dismantling AC Plain or corrugated / transparent sheets in roofing including ridges, hips, valleys and gutters etc. and stacking the material within 50 m lead
100
-
-
Providing & fixing asbestos cement 6 mm thick corrugated sheets in roofing & side cladding and fixing with GI J or L hooks, bolts & nuts 8mm dia including GI plain & bitumen washers complete at all height excluding the cost of purlins, rafters, trusses & other supporting structures at upto 60 - degree pitch (a) Height up to 5.00 M
100
-
-
Providing & fixing asbestos cement 6 mm thick corrugated sheets in roofing & side cladding and fixing with GI J or L hooks, bolts & nuts 8mm dia including GI plain & bitumen washers complete at all height excluding the cost of purlins, rafters, trusses & other supporting structures (a) upto 60 - degree pitch (b) Height above 5.00 M & upto 10.00 M
150
-
-
Providing and fixing 0.63 mm thick with zinc coating corrugated CGI sheets confirming to IS-277-1969 @ 5.70 Kg/Sqm with Zinc coating not less than 275 gm / Sqm in roofing & side cladding fix with galvaised iron J or l hooks or bolts & nuts 8 mm diameter with bitumen & GI limpet washers or with GI limpet washers filled with white lead complete excluding the cost of purlins, rafter and trusses.
60
-
-
Providing & fixing AC ridges & hips in asbestos cement sheet roofing at all height
10
-
-
Providing & fixing plain AC sheet of approved quality with necessary screws / nails etc. complete at all height (frame work to be paid separately) (a) 4mm thick sheet
100
-
-
Providing & fixing wooden beading of size 50 x 12 mm of local hard wood in ceiling to support AC plain sheet at all height including nailing at 100 mm C/C as per the direction of Engineer - In- Charge.
50
-
-
Labour rate for fixing plain or corrugated AC / CGI / Aluminium / translusent sheets in roofing / ceiling and in side cladding fixed with galvanised iron J or L hooks, bolts & nuts of 8mm dia with GI plain & bitumen washers complete excluding the cost of purlins, rafters, trusses and other supporting structures (only sheets shall be supplied free of cost). (a) Height up to 5.00 M
100
-
-
Labour rate for fixing plain or corrugated AC / CGI / Aluminium / translusent sheets in roofing / ceiling and in side cladding fixed with galvanised iron J or L hooks, bolts & nuts of 8mm dia with GI plain & bitumen washers complete excluding the cost of purlins, rafters, trusses and other supporting structures (only sheets shall be supplied free of cost). (b) Height above 5.00 M & upto 10.00 M
10
-
-
Replacement of 8 mm dia GI J or L hooks in roofing / side cladding including fitting and fixing etc all complete at all heights
45
-
-
Steel work in single section fixed with or without connecting plates but including cutting, welding, hoisting, fixing in position all complete in Tee, channels & angles etc and applying a priming
coat of approved steel primer all complete.
500
-
-
Labour rate for steel work in single section fixed with or without connecting plates or in tublar section but including cutting, welding, hoisting, fixing in position all complete in Tee, channels & angles
1
-
-
Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts,cutting rivets, welding etc. dismembering and stacking within 50 M lead
100
-
-
Providing and fixing on wall face unplasticised rigid PVC rain water pipe conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion - single socketed pipes of diameter 150 mm (a) 110MM diameter.
15
-
-
Providing and fixing on wall face unplasticised rigid PVC rain water pipe conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion - single socketed pipes of diameter 150 mm (b) 150 mm diameter
6
-
-
Providing and fixing on wall face unplasticised rigid PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion (a) Bend 110MM diameter.
2
-
-
Providing and fixing on wall face unplasticised rigid PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion (b) Bend150 mm diameter
1
-
-
Providing & fixing approved quality white viterous china water closet squating pan (Indian type WC Pan) size 580 mm including making all connections but excluding the cost of fittings
3
-
-
Providing & fixing a pair of white vitreous china 250 x 130 x 30 mm foot rests of standard pattern for squatting pan closet or urinal basin
4
-
-
Providing & Fixing P or S trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting & making good the walls & floors: (i) 100 mm dia.
1
-
-
Providing & fixing white vitreous china pedestal type water closet of size 580 x 440 mm (European type / wash down type) with seat & lid including making all connection but excluding the cost of fittings
1
-
-
Providing & fixing white solid plastic seat with lid for pedestal type WC pan complete
1
-
-
Providing & fixing approved quality 10 litres low / high level PVC cistern with manually control device (Handle lever) confirming to IS-7231 with all fittings and fixtures complete
6
-
-
Providing & fixing in position 32 mm diameter PVC (approved quality) telescopic flush pipe complete cutting & making good the walls & floors including making all the connection but excluding the cost of fittings
6
-
-
Providing & fixing approved quality white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively
1
-
-
Providing & fixing in position 60 x 45 cm plain mirror superior glass of approved quality complete with 6 mm thick hard board ground fixing to wooden cleats with CP brass screws and washer complete
2
-
-
Providing & fixing in position 600 x 120 x 5 mm glass shelf with edges round of supported on anodised aluminium angle frames CP brass brackets and guard rails complete, fixed with 40 mm long screw, rawl plug etc. complete
1
-
-
Labour rate for repairing of high / low level automatic cistern by adjusting floating valves and other internal fittings as per the direction of EIC.
14
-
-
Providing & fixing in position 400 x 120 mm approved quality PVC shelf fix to wooden cleats with screws complete
1
-
-
Providing & fixing aluminum towel rail of size 600 x 20 mm complete with aluminium brackets fixed to wooden cleats with aluminium screws etc. complete
1
-
-
Providing & fixing white vitreous china wash basin along including making all connections but excluding the cost of fittings of following sizes (i) 550 x 400 mm
2
-
-
Providing & fixing white vitreous china wash basin along including making all connections but excluding the cost of fittings of following sizes (ii) 450 x 300 mm
1
-
-
Providing & fixing brass stop cock of 15 mm @ 400 gms. of approved quality
2
-
-
Providing & fixing MS/CI stop cock of 15 mm of approved quality
1
-
-
Providing & fixing PVC stop cock of 15 mm of approved quality
20
-
-
Providing & fixing PVC stop cock of 20 mm of approved quality
1
-
-
Providing & fixing CP pillar tap @ 400 Gms. of approved quality of 15 mm NB
15
-
-
Providing & fixing brass bib cock of @ 400 gms. approved quality of 15 mm nominal bore
2
-
-
Providing & fixing PVC bib cock of approved quality
200
-
-
Providing & fixing PVC waste of approved quality.
15
-
-
Providing & fixing White glazed fire clay drain board of approved size 600 x 450 x 25 mm
1
-
-
Providing & fixing White glazed fire clay kitchen sink of approved size including making all connections excluding cost of fitting.
1
-
-
Providing & fixing heat resistant connection pipe with brass union 15 mm nominal bore of length 45Cm leangth (a) 15 mm nominal bore
1
-
-
Providing & fixing heat resistant connection pipe with brass union 15 mm nominal bore of length 45Cm leangth (b) 20 mm nominal bore
1
-
-
Providing & fixing CP brass toilet paper holder of approved quality
1
-
-
Providing CP brass telephonic shower of approved quality.
1
-
-
Providing & fixing CP brass towel ring of approved quality
1
-
-
Providing & fixing CP brass soap dish of approved quality
1
-
-
Providing & fixing 100 mm sand cast iron grating for gully, floor or Nahani trap
1
-
-
Providing & fixing CP brass liquid soap container of approved quality
1
-
-
Providing & fixing CP brass shower rose of approved quality with 15 mm or 20 mm inlet of 100 mm dia
1
-
-
Providing & fixing CP brass wall mixture of approved quality.
1
-
-
Providing & fixing CP brass towel rail of size 600 x 20 mm complete with CP brass brackets fixed to wooden cleats with CP brass screws
1
-
-
Providing & fixing CP brass stopcock of standard design and of approved make conforming to IS:8931 (1) 15 mm NB
1
-
-
Dismantling GI pipes (External work) including excavation and refilling trenches after taking out the pipes manually / by mechanical means including stackibg of pipes within 50 metres lead as per direction of EIC :(a) From 15 mm to 40mm NB
300
-
-
Dismantling GI pipes (External work) including excavation and refilling trenches after taking out the pipes manually / by mechanical means including stackibg of pipes within 50 metres lead as per direction of EIC :(b) Above 40 mm NB
50
-
-
Repairs to GI lines including trenching, cutting the old pipes, taking out the same, rethreading & back filling etc. required for refixing the same: (a) GI pipes from 15 mm to 40 mm Nominal bore.
100
-
-
Minor repairing of Brass bib cock, stop cock & CP pillar tap as per instruction of EIC
20
-
-
Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(a) 15 mm nominal bore
6
-
-
Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(b) 20 mm nomonal bore
100
-
-
Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(c) 25 mm nominal bore
12
-
-
Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(d) 40 mm nominal bore
12
-
-
Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(e) 50 mm nominal bore
6
-
-
Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(f) 80 mm nominal bore
6
-
-
Labour rate for laying GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(a) 15 mm nominal bore
1
-
-
Labour rate for laying GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(b) 20 mm nomonal bore
1
-
-
Labour rate for laying GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(c) 25 mm nominal bore
1
-
-
Labour rate for laying GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(d) 40 mm nominal bore
1
-
-
Labour rate for laying GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(e) 50 mm nominal bore
1
-
-
Labour rate for laying GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(f) 80 mm nominal bore
1
-
-
Providing & fixing Chlorinated Polyvinyl Chloride (CPVC) plumbing pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing of pipewith clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. EXternal work- Exposed on wall- 15mm nominal outer dia pipes:(a) 15 mm nominal bore
250
-
-
Providing & fixing Chlorinated Polyvinyl Chloride (CPVC) plumbing pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing of pipewith clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. EXternal work- Exposed on wall- 15mm nominal outer dia pipes:(b) 20 mm nomonal bore
250
-
-
Providing & fixing Chlorinated Polyvinyl Chloride (CPVC) plumbing pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing of pipewith clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. EXternal work- Exposed on wall- 15mm nominal outer dia pipes:(c) 25 mm nominal bore
250
-
-
Providing & fixing Chlorinated Polyvinyl Chloride (CPVC) plumbing pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing of pipewith clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. EXternal work- Exposed on wall- 15mm nominal outer dia pipes:(d) 40 mm nominal bore
200
-
-
Providing & fixing Chlorinated Polyvinyl Chloride (CPVC) plumbing pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing of pipewith clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. EXternal work- Exposed on wall- 15mm nominal outer dia pipes:(e) 50 mm nominal bore
6
-
-
Labour rate for laying CPVC plumbing pipes (Schedule-40) as per ASTM-D-1785 & both end threads as per IS:554 complete with CPVC plumbing fittings including trenching & refilling etc. (External work) - GI fittings shall be paid extra:(a) 15 mm nominal bore
1
-
-
Labour rate for laying CPVC plumbing pipes (Schedule-40) as per ASTM-D-1785 & both end threads as per IS:554 complete with CPVC plumbing fittings including trenching & refilling etc. (External work) - GI fittings shall be paid extra:(b) 20 mm nominal bore
1
-
-
Labour rate for laying CPVC plumbing pipes (Schedule-40) as per ASTM-D-1785 & both end threads as per IS:554 complete with CPVC plumbing fittings including trenching & refilling etc. (External work) - GI fittings shall be paid extra:(c) 25 mm nominal bore
1
-
-
Labour rate for laying CPVC plumbing pipes (Schedule-40) as per ASTM-D-1785 & both end threads as per IS:554 complete with CPVC plumbing fittings including trenching & refilling etc. (External work) - GI fittings shall be paid extra:(d) 40 mm nominal bore
1
-
-
Labour rate for laying CPVC plumbing pipes (Schedule-40) as per ASTM-D-1785 & both end threads as per IS:554 complete with CPVC plumbing fittings including trenching & refilling etc. (External work) - GI fittings shall be paid extra:(e) 50 mm nominal bore
1
-
-
Making connection GI distribution branch with main, by providing & fixing tees, nuts etc. including cutting and threading the pipes, testing etc. complet.(a) 25 mm to 40 mm Nominal Bore
1
-
-
Making connection GI distribution branch with main, by providing & fixing tees, nuts etc. including cutting and threading the pipes, testing etc. complet.(b) 50 mm to 80 mm Nominal Bore
1
-
-
Providing & fixing gun metal gate valve with CI wheels of approved quality (screwed end):(a) 25 mm nominal bore
2
-
-
Providing & fixing gun metal gate valve with CI wheels of approved quality (screwed end):(b) 40 mm nominal bore
1
-
-
Providing & fixing gun metal gate valve with CI wheels of approved quality (screwed end):(c) 50 mm nominal bore
1
-
-
Providing & fixing gun metal gate valve with CI wheels of approved quality (screwed end):(d) 80 mm nominal bore
1
-
-
Providing & fixing CPVC valve of approved standard: 25 mm nominal bore
1
-
-
Providing & fixing unplasticised PVC connection pipe with brass union 15 mm nominal bore of length 45 CM length
40
-
-
Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 with GI fittings and clamps including cutting and making good the walls & floors etc. complete in all respect (internal work):(a) 15 mm nominal bore
80
-
-
Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 with GI fittings and clamps including cutting and making good the walls & floors etc. complete in all respect (internal work):(b) 20 mm nomonal bore
12
-
-
Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 with GI fittings and clamps including cutting and making good the walls & floors etc. complete in all respect (internal work):(c) 25 mm nominal bore
6
-
-
Labour rate for laying GI pipes confirming to IS 1239 (Part-1) / 2004 with GI fittings and clamps including cutting and making good the walls & floors etc. complete in all respect (internal work):(a) 15 mm nominal bore
1
-
-
Labour rate for laying GI pipes confirming to IS 1239 (Part-1) / 2004 with GI fittings and clamps including cutting and making good the walls & floors etc. complete in all respect (internal work):(b) 20 mm nomonal bore
1
-
-
Labour rate for laying GI pipes confirming to IS 1239 (Part-1) / 2004 with GI fittings and clamps including cutting and making good the walls & floors etc. complete in all respect (internal work):(c) 25 mm nominal bore
1
-
-
Labour rate for laying GI pipes confirming to IS 1239 (Part-1) / 2004 with GI fittings and clamps including cutting and making good the walls & floors etc. complete in all respect (internal work):(d) 40 mm nominal bore
1
-
-
Providing & fixing Chlorinated Polyvinyl Chloride (CPVC) plumbing pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing of pipewith clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. Internal work- Exposed on wall- 15mm nominal outer dia pipes:(a) 15 mm nominal bore
200
-
-
Providing & fixing Chlorinated Polyvinyl Chloride (CPVC) plumbing pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing of pipewith clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. Internal work- Exposed on wall- 15mm nominal outer dia pipes:(b) 20 mm nomonal bore
12
-
-
Providing & fixing Chlorinated Polyvinyl Chloride (CPVC) plumbing pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing of pipewith clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. Internal work- Exposed on wall- 15mm nominal outer dia pipes:(c) 25 mm nominal bore
6
-
-
Labour rate for laying CPVC plumbing pipes (Schedule-40) as per ASTM-D-1785 & both end threads as per IS:554 complete with CPVC plumbing fittings and clamps, including cutting and making good the walls etc. (Internal work), exposed on wall:(a) 15 mm nominal bore
1
-
-
Labour rate for laying CPVC plumbing pipes (Schedule-40) as per ASTM-D-1785 & both end threads as per IS:554 complete with CPVC plumbing fittings and clamps, including cutting and making good the walls etc. (Internal work), exposed on wall:(b) 20 mm nomonal bore
1
-
-
Labour rate for laying CPVC plumbing pipes (Schedule-40) as per ASTM-D-1785 & both end threads as per IS:554 complete with CPVC plumbing fittings and clamps, including cutting and making good the walls etc. (Internal work), exposed on wall:(c) 25 mm nominal bore
1
-
-
Labour rate for laying CPVC plumbing pipes (Schedule-40) as per ASTM-D-1785 & both end threads as per IS:554 complete with CPVC plumbing fittings and clamps, including cutting and making good the walls etc. (Internal work), exposed on wall:(d) 40 mm nominal bore
1
-
-
Providing & fixing (i) GI union socket 15 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
40
-
-
Providing & fixing (ii) GI union socket 20 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
50
-
-
Providing & fixing (iii) GI union socket 25 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
5
-
-
Providing & fixing (iv) GI union socket 40 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
2
-
-
Providing & fixing (v) GI union socket 50 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Providing & fixing (vi) GI union socket 80 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Providing & fixing (i) GI plain socket 15 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
85
-
-
Providing & fixing (ii) GI plain socket 20 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
30
-
-
Providing & fixing (iii) GI plain socket 25 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
5
-
-
Providing & fixing (iv) GI plain socket 40 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
5
-
-
Providing & fixing (v) GI plain socket 50 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Providing & fixing (vi) GI plain socket 80 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Providing & fixing (i) GI elbow 15 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
160
-
-
Providing & fixing (ii) GI elbow 20 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
75
-
-
Providing & fixing (iii) GI elbow 25 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
5
-
-
Providing & fixing (iv) GI elbow 40 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
5
-
-
Providing & fixing (v) GI elbow 50 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Providing & fixing (vi) GI elbow 80 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Providing & fixing (i) GI reducing socket 20 - 15 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
50
-
-
Providing & fixing (ii) GI reducing socket 25 - 20mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
10
-
-
Providing & fixing (iii) GI reducing socket 40-25 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
2
-
-
Providing & fixing (iv) GI reducing socket 50-40 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Providing & fixing (v) GI reducing socket 80-50 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Providing & fixing (i) GI Tee 15 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
12
-
-
Providing & fixing (ii) GI Tee 20 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
10
-
-
Providing & fixing (iii) GI Tee 25 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Providing & fixing (iv) GI Tee 40 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Providing & fixing (v) GI Tee 50 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Providing & fixing (i) GI nipple 15 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
12
-
-
Providing & fixing (ii) GI nipple 20 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
6
-
-
Providing & fixing (iii) GI nipple 25 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
2
-
-
Providing & fixing (iv) GI nipple 40 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Providing & fixing (v) GI nipple 50 mm nominal bore in existing GI pipe lines, cutting & threading the pipe and making long screws,including excavation,refilling the earth or cutting of wall and making good the same complete wherever required.
1
-
-
Making temporary connection for social function to be held in BVFCL township quarters as well as public buildings within the township areas by laying PVC pipes as required upto a length of 50 metre and 04 nos. of water points including the cost of all. (Duration of connection shall be for three days).
15
-
-
Dis-connection of water supply line within BVFCL township areas including cleaning of site, earth work in excavation, cutting of pipe(s), plugging of point and deposition of reclaimed serviceable materials in Township store.
2
-
-
Providing & fixing in position 40 mm dia PVC pipe of approved quality (to be used as out lets of sink, wash basin & urinal pan etc.) as per direction of EIC.
10
-
-
Engagement of manpower for miscellaneous assistance in petty civil jobs as per the direction of Engineer-In-charge
70
-
-
White washing with lime on new work (three or more coats) to give an even shade
60
-
-
White washing with lime on old work (one or more coat) to give an even shade
1000
-
-
Colour washing such as green, blue or buff to give an even shade on old work (one or more coat)
120
-
-
Distempering (one or more coat) with oil bound washable distemper of approved brand & manufacture in all shades in old work to give an even shade
10
-
-
Finishing walls with water proofing cement paint of required shade , (a) Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of priming coat.
1
-
-
Applying one coat of water thinnable cement primer of approved brand & manufacture on wall surface
20
-
-
Finishing walls with water proofing cement paint of approved brand and manufature and of required shade to give an even shade: old work (one or more coats) -.
150
-
-
Applying priming coat with ready mixed pink or grey primer of approved brand & manufacture on hard & soft wood work
200
-
-
Applying priming coat with ready mixed red oxide Zinc chromate primer of approved brand & manufacture on steel galvanised iron / steel work
10
-
-
Painting with synthetic enamel paint of approved brand & manufacture in all shades to give an even & smooth shade including cleaning of surface :Old wood / steel works
200
-
-
Painting with synthetic enamel paint (two or more coats) of approved brand & manufacture in all shades to give an even shade - new wood / steel work
200
-
-
Painting with oil type wood preservative of approved brand & manufacture on new work (two or more coats)
1
-
-
Painting with oil type wood preservative of approved brand and manufacture on old work (one or more coats).
1
-
-
Wall painting with plastic emulsion paint of approved brand & manufacture to give an even shade (one or more coat on old work).
1
-
-
Wall painting with acrylic emulsion paint of approved brand & manufacture to give an even shade (two or more coat on new work).
1
-
-
Removing white or colour wash by scraping , sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete
5
-
-
Varnishing with varnish of approved brand and manufacture - two or more coats of glue sizing with copal varnish over an under coat of flatting varnish
1
-
-
French spirit polishing including cleaning of the surface of the dirt, dust and sand papered smooth - One or more coat on old work.
1
-
-
Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
5
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements