Assam Police Housing Corporation Limited Tender

Plain cement concrete apron in prop 1:4:8 with 20mm down graded coarse agg. Over soling including neat cement finish using cement slurry 2.75Kg. of cement per sq.m. of floor (soling to be measured separately). (b) 50 mm thick

25 mm thick cement concrete topping 1:2:4 (1cement : 2 coarse sand : 4 coarse aggregate of 12 mm nominal size) finished with a floating coat of neat cement finish to be laid in panels including curing complete as directed.

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

Providing and laying plain/reinforcement cement concrete works cement,coarse sand,& 20mm down graded stone aggregate including dewatering if necessary,and curing complted but exceding cost of form work and reinforcement for reinforcement cement concrete work. (form work and reinforcement will be measured and paid separately) (A) In substructure up to plinth level without using admixture, M20 grade concrete

(B) In super structure from plinth level up to Roof level. (b) M20 grade concrete

Providing form work of ordinary timber planking so as to give a rough finish including centering,shuttering,shuttering and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0m and removal of the same for in-situ reinforced and plain cement concrete work in. Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc.(a) Using 38mm thick plank

Sides of tie beams, grade beams etc. at or below ground level. (a) Using 38mm thick plank

Columns, Pillars, Posts & Strut (a) Square, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical face (a) Using 38mm thick plank upto Roof

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a) Brick on flat soling.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (I) In Sub-structure upto plinth level including dewatering if necessary (b) In proportion 1:5

(II) In superstructure above plinth level up to 1st floor level (c) In proportion 1:5.(1 cement:5 sand)

Superlight Weight Autoclaved Aerated concrete block work using Grade-I AAC block of compressive strength 40kg/cm2 having dry density 550 to 650 kg/cum conforming to IS-2185 pt-3 or pt-4 in cement mortar of prop 1:4 including racking out jointsand curing complete as specified & directed. (ii)In superstructure above plinth level up to1st floor level

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). a) Normal range ii) Of size 200mmx300mm and above

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (A) CERAMIC ii)Executive range-1 (Sizes 400 mm x 400mm and above) (a) Somany made- VC Shield (Group- 25) (406x406) mm Deluxe -VC

10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to Roofr level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. b) In cement mortar 1:4

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side b) In cement mortar 1:4

Providing and fixing, in position suspended false ceiling using E-Grid (exposed ceiling suspension 2430 system) of grid size 600mm x 600mm/1200mmx600mm with main runner 38 x 24mm, cross tee 29mm x 24mm & wall angle 24mm x 24mm . Using 4mm/6mm thick High Pressure Steam Cured Non Asbestos Fibre Cement Board as per IS 14862, to be placed in a grid of G.I. system duly suspended with 4mm/6mm dia G.I/M.S bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at more than 450mm from the adjacent wall. Flush fitting 1220mm cross tee to be interlocked between main runners @ 610mm c/c, so as to form 600mm x 600mm/1200mmx600mm grid, all complete as per the drawing & directions of engineer-in-charge. Finally, if specified, boards are to be painted with 2 coats of acrylic emulsion paint of approved shade/make over a coat of cement primer before installing it on the grid. (A) Standard Ceilings of Everest make or equivalent as directed by the departement (i) Using 4 mm thick FC Board

Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/ 1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, head and steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be filled up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works etc.complete as directed by the department for all levels. (P.C.C. to be measured and paid for seperately). (a) 1.25mm thick sheet (ii) Size 105mm x 60mm (Single rebate)

Providing, fitting and fixing factory made Santro Flush door shutters having core & cross bands fabricated from seasoned 1st class timber, 25mm core battens, 2.5mm to 3.5mm uniformly thick cross bands, styles & rails made from hardwood timber of width not less than 50mm, fixed to the door frames (chowkath) with necessary hinges, screws, bolts etc. as specified and directed at all levels (Door fixtures and fittings to be measured and paid seperately.) (a) 30 mm thick

Providing, fitting and fixing steel windows/ ventilators (fixed) of standard rolled steel sections as per relevant I.S. Code, joints mitred and welded with 15mmx3mmx100mm lugs embedded in cement concrete block of M-10 grade including applying a coat of red-lead primer.

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

b) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new wall surface (two coats) to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials.

Wall painting (two coats) with acrylic emulsion paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Providing drain with cement concrete (1:3:6) 10cm thick sides 10cm thick bed over brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. ii). 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Supplying fitting & fixing in position reinforcement bars confirming to relevant I.S.Code for RCC work/R.B Walling including straghtining,cleaning,cutting and bending to proper shape and length as per details supplying and binding with 20G annealed black wire and placing in position with proper block,supports,chairs,spacers etc complete.(No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (ii)Super Ductile (SD) TMT reinforcement bars upto Roof.

Supply, Installation, Fixing of DRY CHEMICAL POWDER Fire Extinguisher confirming to IS: 2171 with ISI Mark, and CO2 Cylinder will be confirming to IS: 4947 with ISI Mark, Powder will be confirming to IS: 2878 with ISI Mark (Extinguisher will be TROLLEY MOUNTED)(25 KG) BRAND : FIRESTOP / FIREND / FIRE SHIELD

SANITARY & WATER SUPPLY WORKS : Providing fitting and fixing Vitreous china wall hang water closet (European type W.C pan 400mm high) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately).c) Parryware make i)white (v) Elite S Trap (Cat. No. C0297) (inclusive of seat cover)

Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) i) Parryware make a) White viii) Tiger (CAt No.C8260)

Providing vitreous China wall hang wash basin with CP brass waste coupling of standard pattern, C.P. brass chain with plug, PVC waste pipe including painting of fittings and brackets , cutting and making good the walls and slabs wherever required. (Pillar cock,stop cock, waste coupling are to be paid separately) (B) Hindware Make (a) White (ii) Cute (Cat No. 10053)

Providing fitting and fixing Mirror with plastic frame of size 500x400mm complete as directed and specified.

Providing, fitting and fixing CP soap tray / soap dish complete as directed and specified. (i) Jaquar Make (a) Continental (Cat.No.ACN-1331N)

Providing, fitting and fixing CP towel ring of Jaquar make complete as specified and directed (b) Sona make (i) Towel ring round (Cat.No.TR-06051)

Providing, fitting and fixing CP toilet paper holder of Jaquar make complete as specified and directed (d) Sona make (i) Super (Cat. No.AL-1001)

Providing, fitting and fixing CP Waste Coupling ( half thread HT and Full Thread FT) complete as directed and specified. (b) Sona (i) Rupa 32mm (HT/ FT) (Cat.No.WS-0801)

Providing, fitting and fixing CP bottle trap J type with outlet pipe and wall flange of following size (b) Sona make for basin etc. complete as directed and specified ii) Bottle trap Indian 40 mm (Cat. No. BT- 0752)

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed C) CPVC pipe with CPVC fittings (Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipe)iii) 25mm (OD) diameter

Supplying, fitting and fixing C.P. bib cock 15 mm dia of approved brand directed and specified. Iv) Agmeco brand (i) Bib Cock without Flange CAT No.CC 00204/CAT No.CN 00204

Supplying and fitting, fixing Chrome plated (CP) stop cock of approved brand of size as mentioned below and directed and specified (G.I. and CP pipes will be measured and paid separately) IV) Sona (a) 15mm dia Stop cock male-female /Angle stop cock

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. i) SONA make (b) Heavy type

Supplying, fitting and fixing Chrome Plated (C.P.) divertor of approved brand complete as directed. Jaquar make a)Continental/ Clarion - 4-way divertor for concealed fitting with built in non return valves with divertor handle Cat No.421

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified.(a) 110 mm

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified.(ii) 110mm dia. PVC cowel of ISI make

Supplying, fitting and fixing CPVC ( Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fitting including clams at 1.0 m spacing. This include jointing of pipes and fitting with one step CPVC solvent cement and testing of joints, complete at all levels as directed and specified. (B) Concealed pipe with cutting chases & making good the walls ( d) 40 mm nominal outer dia pipes

Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.

Supplying fitting and fixing overhead adjustable Chrome Plated (C.P.) spray shower 15mm dia. of Sona make with wall flange as directed and specified.(pipes will be measured and paid separately)Jaquar make a) Continental (i) Shower ram 190mm long light body with wall flange

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes 2000 Lt capacity (b) Polycon make

Labour for erecting and placing PCVC Tank over the stagging up to a height of 5.00m complete as directed.(b) 1500 litre capacity

SEPTIC TANK Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil

(B) Extra over item no.1.1(A) above for each 1m depth or part thereof beyond the initial depth of 2m

Supplying and filling sand gravel in foundation trenches of column footings over slushy soil including local carriage of materials within 8 km pumping out of water, ramming etc. complete for strengthening the bearing capacity of the soil as directed and specified including payment of Forest Royalty and Sales Tax and other duties and taxes as may be necessary.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (a) In prop 1cement: 3 sand :6 coarse aggregate by volume

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (I) Using Mixer Machine (A) In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. N) Without using admixture, plasticiser b) M20 grade concrete or Prop. 1:1.5:3

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (I) In Sub-structure upto plinth level including dewatering if necessary (d) In proportion 1:6.

Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. (a) 15 mm thick

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (ii)Super Ductile (SD) TMT reinforcement bars

Providing precast R.C.C slab over drain ,septic tank etc. in prop. 1:2:4 reinforced with 10mm M.S. bar @ 150mm centre both ways tying with 20 gauge black annealed wire with necessary shuttering , curing etc. complete including fixing in position as directed. b) 75mm thick slab

Designing including vetting of design, fabrication, supplying, erection and installation / fixing in position of Pre-Engineered building G+3(04 storeyed building). Complete as per specifications approved drawings or instruction of the consultant architect. Pre-engineered Building' Super structure with structural steel work riveted , bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a primary coat of approved steel primer & epoxy painting two or more coats including all holding down bolts, base plates, gusset plates, nuts, bolts, washers, packings, rivets etc. complete. along with attachment / provision for fixing E&M, OHE and S&T equipments in the building steel roof structures Work to include all intermediate stages of activities not defined herein, but otherwise implied for total completion of work. The rate shall be inclusive of cost of all the materials, factory fabrication, loading, transportation, unloading at site, erection, fixing in position, welding, grinding etc. complete. The gaps between base plates / other gaps will be filled up with ‘Force Rock’ Chemical. The rate will be inclusive of designing of the structure with structure steel taking into consideration the load of total 04 storeys i.e. G+3 building and vetting will be got done by the contractor within 10 days of award of work from reputed institutes like IITs/NITs/Govt. Engineering Colleges. Charges of designing & vetting of steel structure will be included in the quoted & accepted rates, nothing extra will be paid on this account. Pre-engineered Building' Super structure with structural steel work will be designed taking into consideration all loads, pressures, wind pressures, local conditions, relevant earthquake zone, type and use of building, as per the standards, codes of practices etc. complete. Minimum weight of structural steel @ 65 Kg. /Sqm. of mesureable built up area is to be considered while designing the building including weight of structure steel members, base plates, gusset plates, holding down bolts, nuts, bolts, rivets etc. complete. For actual weight above 65 Kg./ Sqm nothing extra will be paid. For all roof slab, roof slab, mumty roof slab, stair case flights / waist slabs, landings etc., 0.80mm thick G.I. deck sheeting will be provided over structural steel roofing members with self driven shear bolts/screws. The cost of this item is included in the quoted & accepted rate of the complete item. Builtup area at all floors from outer to outer of main walls' line will be measured in plan i.e. length & width of building parts in plan. Pipe shafts /ducts projecting out of main walls will not be measured. Roof Projections, Chajjas over openings or any other projections will not be measured for payment. BOLTING: Providing, fabricating and supplying Hot - Dip Galvanized Holding Down Bolts including all assemblies and accessories that are required to be embedded in concrete work by other agencies are included in the rate quoted by the tenderer Bolts shall be of sufficient length to ensure that a minimum 40mm length of threaded portion is embedded in concrete. Threaded portion to be left projecting outside the concrete surface shall be as per requirement of supplier's design and approved drawings. Cost of fabricated, assembled and supplied Bolts shall include all necessary expenses incurred , including costs of all washers, nuts, lock nuts and pins that may be required for securing the structural member with the embedded bolts.