Assam Livestock Development Agency Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 3,27,200Document Cost
₹ 3,300Tender Fee
Refer Documents
Summary
Construction Of Administrative Office Building
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_AHVD_36278_1Bid Award Id
ViewTender No
ALDA/RGM/NAIP III/1095, 12-02-2024Tender Authority
Assam Livestock Development Agency ViewPurchaser Address
-Website
http://https://veterinary.assam.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.
391
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
42
-
-
Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)
41
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)
77
-
-
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
30
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
10304
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.
4667
-
-
Centering and shuttering including strutting, propping etc. and removal of form for i. Foundations, footings, bases of columns, etc. for mass
291.2
-
-
Centering and shuttering including strutting, propping etc. and removal of form for i Suspended floors, roofs, landings, balconies and access
platform
5
-
-
Centering and shuttering including strutting, propping etc. and removal of form for i. Lintels, beams, plinth beams, girders, bressumers and
cantilevers
251
-
-
Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts
186
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)
65.11
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement : 3 coarse sand)
210
-
-
Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).
12
-
-
Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm
9
-
-
Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.Providing and fixing bright finished brass handles with screws etc. complete
9
-
-
Providing and fixing bright finished brass handles with screws etc. complete: 125 mm
9
-
-
Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
9
-
-
Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.
7
-
-
Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately)Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)
43.2
-
-
Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete.
11
-
-
Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete
44
-
-
Float glass panes of nominal thickness 5 mm (weight not less than 12.00 kg/sqm)
44
-
-
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and etc.) trusses etc., including cutting, hoisting, fixing in position and bolted with special shaped washers etc. complete. Hot finished welded type tubes
8974
-
-
Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.
8
-
-
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
552
-
-
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm Thick
31
-
-
Kota stone slabs 20 mm thick in risers of steps, skirting, dado andpillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete
3
-
-
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
189
-
-
Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.
4
-
-
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
6
-
-
Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm
203
-
-
Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.
203
-
-
Providing and laying Polished Granite stone flooring and tread of steps in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent
6
-
-
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
273.4
-
-
Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm)
26.05
-
-
Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)
150
-
-
Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.
30
-
-
12 mm cement plaster of mix 1:4 (1 cement: 4 coarse sand)
211
-
-
15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand)
939
-
-
Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster
279
-
-
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
1168
-
-
Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre
1168
-
-
Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqmover and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
327
-
-
Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats
841
-
-
Applying priming coat With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works
302
-
-
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
302
-
-
Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.
210
-
-
Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .
24
-
-
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25
24
-
-
Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).
21
-
-
Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.
210
-
-
Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade
2826.58
-
-
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
8
-
-
Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.
10
-
-
Demolishing R.B. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within50 metres lead as per direction of Engineer-in- charge.
9
-
-
Extra for cutting reinforcement bars manually/ by mechanical meansin R.C.C. or R.B. work (Payment shall be made on the crosssectional area of R.C.C. or R.B. work) as per direction of Engineerin
5
-
-
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar
5
-
-
Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.
50
-
-
Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.
2
-
-
Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required Single half stall urinal with 5 litre P.V.C. automatic flushing cistern
1
-
-
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer
2
-
-
Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
2
-
-
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board 510x1040 mm bowl depth 250 mm
1
-
-
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
3
-
-
Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.
2
-
-
Providing and fixing 100 mm sand cast Iron grating for gully trap.
3
-
-
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
2
-
-
Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
2
-
-
Providing and fixing soil, waste and vent pipes. 100 mm dia. Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989
35
-
-
Providing and fixing soil, waste and vent pipes. 75 mm dia. Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989
50
-
-
Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes For 75 mm dia pipe
12
-
-
Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes For 100 mm dia pipe
16
-
-
Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :For 100 mm dia pipe
25
-
-
Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :For 75 mm dia pipe
36
-
-
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.For 100 mm dia pipe Sand cast iron S&S as per IS - 3989
4
-
-
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 75 mm dia Sand cast iron S&S as per IS- 3989
3
-
-
Providing and fixing plain bend of required degree. For 100 mm dia pipe Sand cast iron S&S as per IS - 3989
3
-
-
Providing and fixing plain bend of required degree. For 75 mm dia pipe Sand cast iron S&S as per IS - 3989
4
-
-
Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100X100X100X100MM Sand cast iron S&S as per IS - 3989
2
-
-
Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 75x75x75x75 mm Sand cast iron S&S as per IS - 3989
2
-
-
Providing and fixing single equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100X100X100X100MM Sand cast iron S&S as per IS - 3989
3
-
-
Providing and fixing single equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 75x75x75x75 mm Sand cast iron S&S as per IS - 3989
2
-
-
Providing and fixing door piece, insertion rubber washer 3mm thick,bolts & nuts complete For 100 mm dia pipe Sand cast iron S&S as per IS - 3989
2
-
-
Providing and fixing door piece, insertion rubber washer 3mm thick,bolts & nuts complete For 75 mm dia pipe Sand cast iron S&S as per IS - 3989
2
-
-
Providing and fixing terminal guard For 100 mm dia pipe Sand cast iron S&S as per IS - 3989
2
-
-
Providing and fixing terminal guard For 75 mm dia pipe Sand cast iron S&S as per IS - 3989
2
-
-
Providing and fixing collar For 100 mm dia pipe Sand cast iron S&S as per IS - 3989
2
-
-
Providing and fixing collar For 75 mm dia pipe Sand cast iron S&S as per IS - 3989
2
-
-
Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter 100MM
25
-
-
Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter 75 MM
35
-
-
Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989
30
-
-
Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work 100MM dia pipe
45
-
-
Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work 75 MM dia pipe
66
-
-
Providing and fixing SS Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms
3
-
-
Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design
1
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia Pipes
45
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.25 mm nominal outer dia Pipes
56
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External Work 25 mm nominal outer dia Pipes
26
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External Work 32 mm nominal outer dia Pipes
90
-
-
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore
2
-
-
Providing and fixing uplasticised PVC connection pipe with brass unions 45cm length 15mm nominal bore
3
-
-
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
2
-
-
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
3000
-
-
Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore
2
-
-
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 15 mm nominal bore
3
-
-
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore
3
-
-
Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge
3
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B
56
-
-
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
12
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
340
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
180
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 4 sq. mm + 1 X 4 sq. mm earth wire
60
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 6 sq. mm + 1 X 6 sq. mm earth wire
90
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 5/6 A switch
99
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 2 way 5/6 A switch
4
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required15/16 A switch
8
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 3 pin 5/6 A socket
45
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 6 pin15/16 A socket
8
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required Bell push
3
-
-
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required
8
-
-
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required
20
-
-
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 3 Module (100mmX75mm)
4
-
-
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 4 Module (125mmX75mm)
8
-
-
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 6 Module (200mmX75mm)
20
-
-
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 12 Module (200mmX150mm
8
-
-
Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 3 Module
4
-
-
Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.4 Module
8
-
-
Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required 6 Module
20
-
-
Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required 12 Module
8
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required
40
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
19
-
-
Supplying and fixing brass batten/ angle holder including connection etc. as required.
6
-
-
Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.
3
-
-
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door
3
-
-
Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door
2
-
-
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
16
-
-
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole
10
-
-
Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A
4
-
-
Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63A
2
-
-
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
1
-
-
Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
15
-
-
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
1
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 35 sq. mm and upto 95 sq. mm
110
-
-
Providing and fixing lighting conductor finial made of 25mm dia.300mm long GI tube having single prong at the top with 85mm dia. 6mm thick GI base plate including making hole etc as required complete.
1
-
-
Installation,testing and commissioning of ceiling fan, including wiring the down rods of standard length(upto 30cm) with 1.5sqmm FRLS PVC insulated,copper conductor, single core cable and earthing including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
8
-
-
Numbering of ceiling fan/exhaust fan/fluorescent fitting as required.
12
-
-
Installation of exhaust fan in the existing opening, including making good the damages,connection,testing and commissining etc. as required. Upto 450mm sweep.
4
-
-
Providing & fixing of Flotex Flocked Textile floor covering of Nylon 6.6 face fiber or equivalent of approved make with 100% Nylon and completely water proof resilient backing. The flooring should be anti-static with thickness of 4.3mm, and approx. weight of 1.8 kg/ sqm.of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sqm.in the width of 2mtr. The floor covering should have Fire test EN- 13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 class DS, Sanitized anti-microbial treatment, with resilient waterproof backing, anti-allergic which is certified by British allergy foundation, with ten year replacement guarantee complete in all levels as directed.
35
-
-
Providing fitting and fixing Armstrong make 12mmx75mm one side rounded edge wooden skirting as approved and directed.
78
-
-
Providing, supplying and fixing of Frameless Single leaf/double Swing Glass Door of Dorma/ Ozone or equivalent make in glazing using 12mm thick toughened glass of Saint Gobain / or approved equivalent with die cast patch fitting with stainless steel cover including fixing of patch fittings, floor springs, locks, handles etc. using the hardware items as detailed, complete in all respects as per detailed drawings, specifications and direction of Engineer in charge. Single Leaf Door with Dorma or Equivalent Hardware’s a
3.15
-
-
Supplying, fitting and fixing of Roller Blinds (Marvel Make- Shades: Voil/ Orlando/ Revolve) of Translucent make for Office rooms at Assam Electricity Regulatory Commission Office at Six Mile, Guwahati in all complete as approved and specified by the Department.
46
-
-
Providing ditting and fixing of 30 mm thk BWP grade green/century/ or equivalent)solid core flush door with 6mm glass panels fixed on rebate on the face and timber beads on back. The edges of the flush door shall be finished with 6mm thk teak wood liping. The timber beads and teak wood lipping shall be polished as per the approved shade of colour and the door to be finished with 1 mm thk laminate of Greenlam/Century/Merino make on both sides as well as the rebate including nessecary harware fittings like 100 mm SS hinges and screws, complete at all levels as per design and as directed.(lock, door closer/floor spring, tower bolt) to be measured seperately.
20
-
-
Supplying, Fixing and Fitting of not less than 75 mm thick partition wall with 12 mm thk Calcium Silicate "Hilux Boards" make fixed over Gyp steel flanged studs fixed vertically on floor and ceiling at interval of 600mm c/c. The 12 mm thick calcium Silicate board of approved brand to be fixed on the both sides with 25mm drywall screw at 300 mm c/c to one sides of 50 mm studs (0.55 mm thk having one flange of 34mm and another of 36 mm) made of GI steel with joints staggerred, to be complete in all levels as per design and as directed by the department.
89
-
-
Reception Table MAIN TABLE:1800L X750D X 1050HT SPECIFICATION: Main & Return spine - Neo 50mm thick partition system. Finishes / Tiles - Fabric Magnetic tiles are provided, Laminate above & Laminate below table top. Additional Screen - ACRYLIC Screen of 900L at counter Table top - 25mm thick Pre-laminated particle board finished with 2mm PVC edge lipping.Under-structure – necessary MS Brackets Wire Management - Bi Level Raceway on main spine BTT & Skirting is all around the workstation & 65 dia wire manager hole are considereD Make: Featherlite
1
-
-
U SHAPED CONVENTION CENTRE TABLE
Specifications
Table top : 25mm thick Pre-laminate particle board finished with 2mm edge lipping.
Supported : 25mm thick PLB gable ends and 18mm thick 450ht PLT modesty panels with necessary fixtures
Wire Management - 300mm Flip is considered on each table with cable dumb and 3nos vertical wire entry cover.
Make: Featherlite
2
-
-
Conference Main Chair
Model: OPUS HB
High back mesh chair
Base: The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards Gaslift - Class 4 tested -ANSI BIFMA performance
standards Seat and back is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and revited in to the wood Upholstery: Cushion with pre moulded foam of 50 - 60
density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Distinctively and characteristically designed tilt mechanism offering a very smooth and fluidic reclining motion with
tension adjust knob and importantly offering seat to back recline ratio of 3:7, optimal for good back support .Multilock mechanism is fabricated from CR Sheets, undergo through CO2 welding process imparting uniform surface finish and tensile strength. The components are processed with high degree of precision and care so as to assemble with other parts in perfect harmony to give smooth and effortless reclining experience. Make Featherlite.
1
-
-
Conference other Chair Model: Amaze MB
Base: The 640mm dia (26 inches) five pronged base is made out of GF nylon Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards Castors - Twin Castors 50mm dia castors compling to ANSI / BIFMA X 5.1 – 2002 Gaslift - Class 4 tested -ANSI BIFMA performance standards Upholstery: Seat Cushion with pre moulded foam of 50 - 60 density Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Mechanism: Self Calibrating Multilock Mechansim Tested as per BIFMA Standards. Back Frame is inserted with Mesh & Dynamic Adaptable Lumbar Support Tension control is below the Seat. Armrest: Moulded polyurethene Arms confirming to IS 7078 with steel inserts for long Moulded self skinned polyurethene Arms confirming to IS 7078 with steel insets for long life. one way adjustable - Height Adjustable. Fabric: Seat is duly upholstered with approved fabric. Make: Featherlite
25
-
-
CABIN TABLE MAIN CHAIR Model: Astro MB
Astro Medium Back Chair
Single Lock Synchro Mechanism
Adjustable Lumbar Support
One Way Adjustable Arms (Height)
Nylon Base
Make: Featherlite
3
-
-
Reception, Workstation Model: Contact Project Adj Arms.
Contact Project Medium
Mesh Back Chair
Single Lock Synchro Mechanism
Adjustable Arms (Height)
Nylon Base
Make: Featherlite
14
-
-
VISITOR'S CHAIR
Model: Smart VA
Smart Low Mesh Back Visitors chair
Powdercoated Four Legs
Fixed Arms
Make: Featherlite
9
-
-
NEO WORKSTATION WITH 1200HT PARTITION AS PER LAYOUT
LShape WKS - 1350/1500W X 600/600D X 750HT TABLE TOP WITH 1200HT PARTITIONS
Specifications
Table top : 25mm thick Pre-laminate particle board finished with 2mm edge lipping.
Partition And Intermediate Partition : Partition is made of 50mm thick NEO based system with fabric above and lamiante below the table top. Fabric magnetic and glass markers are provided for each workstation
Support: 18mm thick PLB gable ends with necessary brackets
Wire Management: Grommet Hole provided on table top. Raceway provided below table top for Power and Skirting Level for Data.
MOBILE PEDESTAL 2D1F
SIZE: 400W X 450D X 600HT
Pedestal are made of 18mm thick PLB with 2 drawer units and 1 filling folder unit. CPU Trolley and Keyboard Tray
Make: Featherlite
8
-
-
Single Seater- Specification- Size- H- ---- mm, L- ------ mm, D- ---- mm.
All are wooden structure and make with best quality jute fabric upholester
3
-
-
3 seater Sofa- Specification- Size- H- ---- mm, L- ------ mm, D- ---- mm.
All are wooden structure and make with best quality fabric upholestery, seat and back cushion thickness 35density and very comfortable for seat.overall appearance of the product shall be as per photograph
1
-
-
Providing & fixing of AEROLAM/K FOAM XLPE- Chemically Cross Linked Closed Cell Polyethylene foam thermal insulation with nominal density 30 kg/m3 + 10%, having thermal conductivity of 0.0329 W/m ok at 23 oC, mean temperature, as per IS 3346:1980. Material shall be resistant to growth of Fungus as per ASTM C 1338 and resistant to growth of Bacteria as per ASTM E 2180.Fire characteristics shall confirm to BS 476 Part 7, Class 1, for Surface Spread of Flame and meet requirement of Fire Propagation as per BS 476 Part 6, having an index (I) of 5.06 with lamination and 5.17 for plain materials and sub-indices i1(2.71); i2(1.65); i3(0.70).
Visibility due to smoke shall confirm to Class A as per Standard UIC 564 – 2 Appendix 15. Compliance to BS EN 13501-1:2007 + A1:2009 (Reaction to fire performance) for 25 mm thickness sheet with Alupet + self - adhesive with classification BS1D0 in category of combustible thermal insulation with less fire propagation, low heat emission, zero smoke and zero fire droplets. Size: 1.2X20X19MM
236
-
-
Providing fiting and fixing of Wood Plastic Composite (WPC) door frames of natural and brown colour of 100mm x 65 mm section and density not less than 900 kg/ cum, single rebated rectangular section including joining of top mullion and vertical members with mitred joint and fixing to the wall jamb with MS holdfasts/ Metal Screw and metal rawl plug.
22
-
-
Cabin Table
Specification:
Table top : 25mm thick Pre-laminate particle board finished with 2mm edge lipping.
Supported : 25mm thick PLB gable ends and 18mm thick 450ht PLT modesty panels with necessary fixtures.
Wire Management : Grommet Hole provided on table top.
MOBILE PEDESTAL 2D1F
SIZE: 400W X 450D X 600HT
Pedestal are made of 18mm thick PLB with 2 drawer units and 1 filling folder unit. CPU Trolley and Keyboard Tray
Make: Featherlite
3
-
-
Providing and fixing 2.4m high FRAMELESS GLASS INTERNAL PARTITIONS at all locations with 12mm clear tempered glass or as per elevation drawings enclosed with approved make of 316 grade patch connector S.S. fittings of DORMA/Ozone or equivalent make , fixed with S.S. screws or with fixing clips including necessary filling up gaps at junction, at top, bottom u channel make jindal and sides with required weather silicon with backer rod shall be inserted between alluminium section channel and glass as well as both inside and outside around the periphery of the glass to make the glazing water tight and air tight as shown in enclosed drawings and directions of Engineer-in-charge. Glasswork including making suitable holes in the glass before tempering process of glass, for installation complete as per design drawings. The periphery shall have to be sealed both from inside and outside with silicon weather sealant to make the glazing water and air tight.The sealing of glass to patch connector hardwares with stainless steel fixtures as detailed in drawings. Silicon sealant grade shall be "Dow corning - USA" or " "WACKER - Germany" or approved equivalent as per the design requirement. The partition shall be aligned for the entire height and for the entire length by laser beam equipment to ensure 100 percent X-axis and Y-axis alignment. The glass joints must be properly sealed with weather silicon to make the joint water tight and air tight as well as per design complete at all levels and as directed.
6
-
-
Providing, fitting and fixing CP soap tray / soap dish complete as directed and specified.
3
-
-
Providing, fitting and fixing Liquid soap dispenser and liquid soap container complete as directed and specified.
2
-
-
Providing, fitting and fixing CP towel rail complete as directed and specified.
2
-
-
Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified.
2
-
-
Providing, fitting and fixing robe hook complete as directed and specified.
2
-
-
Providing and fixing brass two way bib cock of approved qualiity
2
-
-
Providing and fixing CP grating of approved quality and colour
3
-
-
Providing and fixing sink cock of approved quality: 15 mm nominal bore
1
-
-
Supply of recessed mounting glare less LED down light of size 2'x2'(120Lumen/watt) Crompton or equivalent make.(LCTLRP-24 FO-CDL).
16
-
-
Supply, installation, testing and commissioning of surface mounting LED panel ,down light suitable for any modern workspace with robust Aluminium housing and 5700K, 4000K,3000K CCT Efficacy 100LM/W. Crompton or equivalent make.(LCDSPLN-R-06-CDL).
16
-
-
Supply, installation, testing and commissioning of wall/ceiling mounting LED polycarbonate tube with inbuilt driver metal heat sink with double sided connection. Crompton or equivalent make.(LT8-20-865(2).
8
-
-
Supply of 1200mm sweep, low power consumtion(LPC) ceiling fan, 5 Star Rating
8
-
-
Supply and insatallation of 300 mm sweep metalic ventilating/exhaust fan 900 RPM heavy duty Usha or equivalent make
4
-
-
Supply and insatallation of 400 mm sweep metalic wall fan heavy duty Usha or equivalent make
4
-
-
Suppying and laying of Cat-6 LAN cable as per rquirement at site.
600
-
-
Supplying of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 650/1100 V grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required.
3 X 6 sq.mm
76
-
-
Supplying of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 650/1100 V grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required.
4 X 16 sq.mm
55
-
-
Supplying of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 650/1100 V grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required.
3 ½ X 70 sq.mm
130
-
-
Supply fiting and fixing of Bluestar make 2.0 ton inverter Hi wall AC unit with cordless remote including outdoor and indoor unit and necessary additional copper piping up to 5 m with thermo insulation and including PVC drain pipe and voltage stabilizer and electrical cable installation complete as directed by department.
2
-
-
Supply fiting and fixing of Bluestar make 1.5 ton inverter Hi wall AC unit with cordless remote including outdoor and indoor unit and necessary additional copper piping upto 5 m with thermo insulation and including PVC drain pipe and voltage stabilizer and electrical cable installation complete as directed
2
-
-
Supply fiting and fixing of Bluestar make 1.0 ton inverter Hi wall AC unit with cordless remote including outdoor and outdoor unit and necessary additional copper piping upto 5 m with thermo insulation and including PVC drain pipe and voltage stabilizer and electrical cable installation complete as directed by department.
2
-
-
Supply and installation of mono ammonium phosphate based dry powder 1.3kg. Capacity fire extinguiser ball.
2
-
-
Supply and installation of mono ammonium phosphate based dry powder 04kg. Capacity ABC stored pressure type fire extinguiser.
1
-
-
Supply and installation of 2kg. Capacity CO2 type fire extinguiser.
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements