Assam Electricity Grid Corporation Limited Tender

Supplying and stacking of stone Crusher dust finer than 3mm with not more than 10% passing 0.075 sieves including transportation of the materials to the site.

Labour for laying, spreading, dressing of stone matel and stone dust as directed by the department including all lead and lift.

Providing SUN ROCK HIGH/DEVI paver block/tiles of concrete grade M30 or above of approved quality size, shape of specified thickness over a levelling bedding layer of 30mm compacted sand over a base course of WBM or PCC (base course to be paid separately) including cutting where necessary finished with spreading, sweeping jointing sand and compacting the pavers using vibrating compactor as specified and as directed by the department including all lead and lift. a) 80mm thick

Construction of sub-grade and earthen shoulder with approved materials obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 (including cost of testing of materials at site and laboratory as directed by the department) including transportation of the materials to the site. a) From private land

Extra lead 55.00 km, 55.00-5.00= 50.00 km

Earth work in excavation for foundation trenches of walls, retaining walls, footings of column, steps septic tank etc. including refilling (return filling) the quantity as necessary after completion of the work, breaking clods in return filling, dressing, watering & ramming etc. And removal of surplus earth with lead & lifts as directed and specified in the following classifications of soil including bailing out water where necessary as directed and specified. A) Up to a depth of 2m below G.L. b) In ordinary soil.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately) including transportation of the materials to the site. a) In prop 1:3:6 aggregate

Construction of Storm water drain at 132/33kV Karimganj Sub-Station parallal to the Approach road

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a).Brick on flat soling.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (I) In Sub-structure upto plinth level including dewatering if necessary. (a) In proportion 1:3.

(II) In superstructure above plinth level up to 1st floor level. (a) In proportion 1:3.(1cement:3sand)

10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. a) In cement mortar 1:3

Providing and applying over sunken slab etc., two coats of waterproofing slurry prepared with neat cement, water and modified Styrene Butadiene Rubber based polymer like Sika Latex of Sika India Ltd./Dr. Sealkit Masterbond Latex (Asian Chemicals)/ RHEOMIX 141 by brush after proper surface preparation (surface preparation including thorough cleaning of surface to be measured and paid separately) as specified & directed by the Department complete.

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. (b) Using 25mm thick plank

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work. (I) Using Mixer Machine. (A) In substructure up to plinth level- N) Without using admixture, plasticiser b) M20 grade concrete or Prop. 1:1.5:3

Demolishing brickwork including stacking of serviceable materials and disposal of unserviceable materials as directed for all levels

Street light installation covering from N.H up to Colony end of the approach road at Karimganj 132/33Kv Grid Sub-station

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed A) G.I. pipe with GI fittings a) TATA / SAIL (Medium) vi) 50mm diameter

Renewing G.I. bend (heavy quality) as specified & directed.(e) 50 mm dia

CLAMP, JAM NUT, Clamp fitting holding with necessary metal fasteners & screws, (a) 1216/1620

Pole Type BOP or equivalent-7030 Height 7m The materials of the pole as follows : Conforming to grade S355JO Conforming to grade S355JO , Base Plate Fe 410 Conforming to IS 226/ IS 2062, Foundation Bolts:- 6.8 Gr. As per IS 1367, Pole Sections :- The Octagonal Poles shall be in single piece with single longitudinal welding join, Galvanization :- The poles shall be hot dip galvanized as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 65 micron. The galvanizing shall be done in single dipping. Door opening :- The Octagonal poles shall have door of approximate 500 mm length at the elevation of 500 mm from the base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connection as approved by the Depts.. The door shall be flush with the exterior surface and shall have suitable locking arrangement. The pole shall be adequately strengthened at the location of the door compensate for the loss in section. There shall also be suitable arrangement for the purpose of earthing, Smart pack Junction box with 6 MCB & Terminals for mounting inside base compartment of Pole. Top Dia. (A/ 70mm Bottom Dia. (A/ 130mm , Sheet Thickness 3mm , Base Plate dimensions :- (L x B x 220 x 220 x 12, Foundation Bolt , Bolt Size :- (no. x dia.) 4 x 20 Dia, Pitch Circle Dia. (PC 205 Bolt Length 750, Projected Bolt Length 100mm, Anchor plate thickness:- 4 mm , Pole Foundation :- The octagonal poles shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. Foundation:- The foundation shall be done with ( Earth work:- 2.04 cubic Meters.RCC :- 1:1.5 : 3 proportion 0.65 cubic metres. Steel :- 22.43 Kg. Shuttering :- 4.32 square metres. = 22.43 Kg.

Supplying with fitting & fixing of the following integral type street light luminaries complete and consisting of single piece integral epoxy gray powder coated dia cast aluminium housing gasket, pot optic reflector, cast aluminium frame from heat resistance toughened clear glass cover and accessories such as Condenser, lamp Holder, Ballast, lamp etc. in the existing pole including making necessary connection as approved by the Deptt.)with 2× 2.50 sq.mm F.R. multistrand and P.V.C. insulated single core copper cable as specified and directed by the department. Philips make) Cat No.SGP 401 1xSONT-150W For Lamp 1xSONT-150W (IP-65) / Crompton Greaves make) SSGN1215H/FG For lamp 1x150W HPSV (T) / Havells: LHBW20115036 For lamp 1x150W SON-T.

Philips make) Cat No.SGP 401 1xSONT-250W For Lamp 1xSONT-250W (IP-65) / Wipro make) : WST25250 For lamp 1x250W HPSV (/ Crompton Greaves make) SSSG1225IH/FG For lamp 1x250W HPSV (T) .

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. ABB, Schneider MG, legrand, Hager make) 4 way SPN double door

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series-(Schneider MG, legrand, Hager make)- 6 to 32A

Supplying with fitting and fixing SPN 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. B Series-(Schneider MG, legrand, Hager make) 6 to 32A

Supply and fixing 32 mm mm dia 2.00mm average wall thickness heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) on surface system including painting etc as required:

Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts ( Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in existing surface conduit wiring system including connection as required. With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. copper conductor cable

With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. copper conductor cable

Making/fabrication and installation 1(one) security booth with all associated work at 132/33KV Karimganj Grid Sub-Station

Recuirement of MS angles of size (45×75×6/100×100×8mm) (a) 11.5'×4 nos or 3.5m×4 nos= 46 Rft or14 Rm (for 4 nos leg)

(b) 6'×4 nos or 1.83×4 nos = 24 Rft or 7.32 Rm (for base structure)

(c) 8'×1 no or 2.44×1 no = 8 Rft or 2.44 Rm(back side foot step)

(d) 12'×1 no or 3.66×1 no = 12 Rft or 3.66 Rm (base cross for leg)

(e) 6'×8 nos or 1.83×8 nos =48 Rft or 14.64 Rm(for bottom floor structure)

Recuirement of MS angles of size (45×45×6mm) (a) 6'×6' nos or 1.83×6 nos = 36 Rft or 10.98 Rm(for celling structure)

(b) 6'×6 nos or 1.83×6 nos = 36 Rft or 10.98 Rm (for fitting MS sheet)

(c) 3'×12no or 0.915×12 nos= 36 Rft or 10.98 Rm(for fitting MS sheet)

Cost of making/ fabrication of 1 (one) Security Booth by detachable MS angle structure (providing nuts, bolts system) upto celling level & fitting fixing of MS Sheet upto three feet height from floor structure & on foot step in the back side as per departmental design & drawing by using MS angle of different cross section & length as specified by the department complete with cutting, setting, welding & drilling etc. like MS sheet, nuts, bolts & washer, labour charge but excluding the cost of requisite MS angle (which will be supplied by the department)

Cost of making/ fabrication of roof structure aforesaid Security Booth after fixing 1 2" dia vertical pipe above the celling structure by using MS pipe of 1 inch dia & having requisite length as per departmental design and drawing to facilitate fixing of dyna roof sheet & riddges etc. complete with cutting, setting, welding etc. including the cost of all requisite materials like MS pipes etc. & labour charges.

Fitting fixing of dyna sheet, ridges, top cap with plastic kodai to be fitted on the top of the centre pipe complete with cutting, setting, drilling, spring etc. including the cost of dyna roof sheet (8'×6 nos) ridges (4 nos), plastic heavy kodai 1 no screw etc. & labour charges complete.

Cost of carriage/transportation of detachable Security Booth structure after completion of febrication work at Silchar to Karimganj Grid Sub-Station complete with the cost of refitting as per departmental drawing at Sub-Station Site.

Cost of excavation of 4 (four) nos foundation pit followed by CC grauting of 4 (four) nos leg of Security Booth structure up to a deoth of 2 (two) feet & per directive of the department including the cost of all requisite materials & labour charges ut to back filling of the earth.

Cost of fitting fixing of Ply board/ block board ceilling to be fitted in the ceilling structure along with a provision of fan hook as directed by the department including the cost of all requisite materials & labours charges complete with painting of ceilling.

Cost of 3 (three point electrical wiring in the security booth such as light, fan, and plug point as directed by the department complete with the cost of wiring materials and one 4 (four) feet tube light set with frame, tube, electronic ballast & one reputed 48'' size ceilling fan.

Cost of making 3 (three) nos of RCC slab having size 3'×2' and requisite thickness as per structure groove complete with meal cement finish by mixing red oxide powder to provide red colour and fitting fixing the same in the groove in proper manner including the cost of all requisite materials and labour charges.

Cost of painting of all iron structure after cleaning, scrubbing then to apply metal primer cost followed by atlest two coats of synthetic enamel pain of reputated make and shade as directed by the department including the cost of all requisite materials like metel primer, synthetiv enamel pain etc. complete with labour charges.

Granite slate (3½' × 1½') with iron structure (black)

Cost of excavation of front step aforesaid Security Booth by brick and PCC work in proportion 1:2:4, 10 mm thick cement plastering is single coat of outside brick wall including cost of materials and labour charges & back filling of earth.

Supply good quality of bamboo Curtains (6×5') 2 nos including fitting etc.