Pradhan Mantri Gram Sadak Yojana Tender

Granular sub-base/base/surface course with local materials (Table 400.13) by mix in place method normal Construction of granular sub-base by providing local material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at once and compacting with smooth wheel roller to achieve the desired density complete as per Clause 401.4 as per Technical Specification Clause 408. (i) Using naturally occuring gravel.

Sub-Head: WBM-III

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.(A) By manual means

Sub-Head: PMC

Providing and applying of prime coat with bitumen emulsion(SS-1) on prepared surface of granular base i/c clearing of base surface and spraying emulsion at the rate of 0.7 - 1.00 kg per sqm. using mechanical means as per technical specification clause 502 (high porosity).

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508.(i) By manual means Bitumen(S-65)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 (i) Type A Bitumen S-65.

Sub-Head :- Protective Works

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottoms and backfilling in trenches with excavated suitable materials. 1. Ordinary soil (i) Upto 3m depth

Providing and laying wire createwd boulder structure boulder size 225 Cm to 45 Cm having 25 Kg average weight for each I/C dumping / laying in SWG wire mesh of 10 Cm x10 Cm 4 MM dia I/C packing with small size of stone spals and carraige of boulder for a lead of 50 mtr and lift up to 1.5 Mtr

Sub-Head :- Side Drain

Earthwork in excavation for structures as per drawing and technical specification clauses 305.1 i/c setting out , construction of shoring and bracing of stumps & other deterious materials and disposal upto a lead of 50 .00 mtr , dressing of sides & bottom

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203.(i) PCC grade M10.(I) Nominal mix 1:3:6

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( M15 Nominal mix (1:2.5:5 ) )

Cement plastering 1: 4 (1cement,4 sand)

Sub-Head: Traffic Sign and Logos

Providing and fixing typical PMGSY informatory sign board with logo as per MoRD specification and drawing. Three MS plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 25mm x 5mm. The iron frame of the lower most plate and flat iron frame will be welded welded to 2 nos 75mm x 75mm of 12 SWG sheet tubes posts duly embeded in cement concrete M15 grade blocks of 450mm x450mm x600mm, 600mm below ground level. The topmost diomond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plates tube. All MS will be stove enameled on both sides. lettering and printing arrows, border etc will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed post and steel tubes will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1.

a) Informatory board

b) Citizen information Maintenance board

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per clause 1701.3.9 of MoRD for Rural Roads of required shade and colour supported and welded on 47mmx47mmx12 SWG sheet tube firmly fixed to the ground by means of properly designed foundations with M15 grade concrete 450x450 x600mm,600mm below ground level as per approved clause 1701.2.2. a) Traffic Signs(Cautionary signs etc)

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703.( a) Bench mark stone

(b)T B M Stone

(c) 200 mtr stone

Routine Maintenance

First Year

Second Year

Third Year

Fouth Year

Fifth Year