Pradhan Mantri Gram Sadak Yojana Tender

Construction of back piller as per Fig. 1600.1( c) as per drawing and Technical Specification Clause 1602.3

Construction of Job pillers as per Fig. 1600.1 (d) and Technical Specification Clause 1602.4

PAVEMENT (Shoulder & Subgrade preparation, GSB LAYER, WBM-3, PrimeCoat ,Tack Coat, PMC , Seal Coat)

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1.

Granular sub-base/base/surface course with local materials (Table 400.13) by mix in place method normal Construction of granular sub-base by providing local material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place

Providing , laying , spreding and compacting stone aggregates of specific size to water bound macadam specification i/c spreding of uniform thickness , hand pcking . rolling with smooth wheel roller 80- 100 KN in stages to proper grade and camber , apply

Providing and applying primer coat with Bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 1.2-1.5 kg/sqm using mechanical means as per Technical Specification Clause 502. High Porosity

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion pressure distributor at the rate of 0.30 to 0.35 kg per sqm on the prepared non-bituminous surfaces (cement concrete pavement) cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. By Manual Means, Bitumen (S-90)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510. By Manual Means ,T ype A , Bitumen (S-90)

Cement Concrete Drain

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of side.and bottom and backfilling in trenches with excavated suitable material up to 3.0 m depth.

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

I). P.C.C grade M 10 ( Nominal mix 1:3:6 base

Stone masonary in cement mortarfoundations complete as per drawings and technical specifications Clause702,704, 1202 & 1203 in RRM 1:5.

Cement plastering 1: 4 (1cement,4 sand)

Logo/Road furniture/Traffic Sign.

Providing and fixing typical PMGSY informatory sign board with logo as per MoRD specification and drawing. Three MS plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 25mm x 5mm. The iron frame of the lower most plate and flat iron frame will be welded welded to 2 nos 75mm x 75mm of 12 SWG sheet tubes posts duly embeded in cement concrete M15 grade blocks of 450mm x450mm x600mm, 600mm below ground level. The topmost diomond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plates tube. All MS will be stove enameled on both sides. lettering and printing arrows, border etc will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed post and steel tubes will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1.

a) b) PMGSY Logo

b) Citizen information board

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per clause 1701.3.9 of MoRD for Rural Roads of required shade and colour supported and welded on 47mmx47mmx12 SWG sheet tube firmly fixed to the ground by means of properly designed foundations with M15 grade concrete 450x450x600mm,600mm below ground level as per approved clause 1701.2.2 a) Traffic signs ( cautionery signs etc.)

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703

Ordinary Kilometre Stone (precast)

5th Km stone

200 m stone

SH:- 5 - Years Maintenance

First Year Maintenance

Second Year Maintenance

Third Year Maintenance

Fourth Year Maintenance

Fifth Year Maintenance