Tirumala Tirupati Devasthanams Tender

Demolition including stacking of serviceable materials and disposal of unserviceable materials within 100 metres lead - Brick work

Demolishing and disposal of unserviceable materials within 100 metres lead - Unreinforced cement concrete up to 15cm thickness

Dismantling doors, windows and clear storey windows, ventilators etc, (wood or steel) shutters including chowkhats, architraves, hold fasts and other attachments etc., complete and stacking them within 100 metres lead - Not exceeding 3 sq.m in area

Conveyance of waste materials such as debris, dismantling meterials ect with a lead of 5 kms from work site including loading unloading etc., complete

Cement Concrete (1:4:8) using 40 mm ( 0.54 cu.m), 20mm (0.27 cu.m) and 12 mm (0.09 cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including curing, ,machine mixing, cost and conveyance of all materials etc., complete.

Cement Concrete (1:2.5:5) - Grade M15 using 20mm (0.54 cum) and 12mm (0.36 cum) nominal size HBG crushed metal from any source conforming to the relevant ISI Standards for foundations etc., laid in layers of not more than 15cm thick well compacted including curing cost, machine mixing, cost and conveyance of all materials etc., complete

Supply and placing of the M20 Design Mix using of 10mm HBG crushed metal 0.480cu.m,6mm HBG Crushed metal 0.320cu.m,sand 0.400cu.m and cement 350Kg with water cement ratio of 0.53(185.50 ltrs/cu.m of CC) etc., from any source confirming to the relevant ISI standard including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with minimum cement content as per IS code from standard suppliers approved by the department but excluding cost of steel and its fabrication charges, centering charges, shuttering charges for finished item of work (APSS No. 402) Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix if mixing is done by volume mixing.

- do - for 50 mm thick precast slabs using 10 mm graded aggregate HBG crushed metal from any source conforming to the relevant ISI standards, with necessary reinforcement excluding cost of steel and tying of grills, centering charges,but including cost of necessary form work etc., complete as directed by the department.

Construction of Brick Masonry in CM(1:6) using well burnt Bricks 2nd class or ground moulded (Non- modular or traditional size) (230 x 110 x 70 mm)including curing, cost and conveyance of all materials as directed during execution and complying with standard specifications etc., complete.

Construction of 110 mm thick Brick partition walls CM (1:4) using well burnt bricks 2nd class or ground moulded (Non modular or traditional size) bricks (230X110X70 mm) including curing, cost and conveyance of all materials etc,. complete

Plastering in Cement mortar 12 mm thick using best river sand from approved quarry including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete for the following proportions

in CM (1:5) 12 mm thick

in CM (1:3) 12 mm thick

Flooring with Antiskid floor tiles 1st quality of all series& shades (as per manufacture specification), set over base coat of cement mortar (1:6) 20mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.30 kgs per sq.m. jointed with neat cement to full depth mixed with pigment of matching shade, including cost and conveyance of all materials like flooring slab, cement, sand and water etc., complete, for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply). '-do- Supply of Non-skid red or white full body Ceramic floor tiles of size 450 x 450 mm and thickness between 7-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs

Finishing the sides of walls with Ist quality glazed wall tiles of following sizes of approved colour and brands including pointing the joints with the same colour of cement by mixing the same colour pigment in white cement and over a bed of C.M.(1:3), 12 mm thick & Cement slurry of 33 Kg/10sq.m shall be used for fixing bed tiles including cost and conveyance of all materials, curing, incidental charges etc., complete (No separate plastering shall be paid to the walls). (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply). 'Supply of glazed red or white full body ceramic wall tiles of size 300 x 450 mm / 320 mm x 400 mm and thickness 6 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs

Flooring with vitrified tiles of 1st quality of following varieties of series and shades set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sq.m & joints with spacer joints with 3 mm wide jointed neatly with filer material of cement/epoxy grout/white cement paste to full depth mixed with pigment of matching shade as directed during execution, including cost and conveyance of all materials, etc., complete - for finished item of work.(Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply) Supply of soluble salt porcelain vitrified tiles screen printed and polished of size 600 x 600 mm and thickness between8-10 mm 1st quality conforming to IS:13711, IS:13712,IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs.

SPECIALISED INJECTION GROUTING WITH CEMENT AND FREE FLOW ADDITIVES: a]. Drilling of holes with power drilling machine to the required depth [12mm to 14mm dia holes] b]. Fixing of Rubber Nozzles with cement and quick setting, Rapid hardening compound putty - Rapidstrong qs or equivalent. c]. Grouting of holes with 140 PSI Grout pump with cement slurry mixing with Specialized Free flow, Non-shrink Grout additive - RAPIDSTRONG GROUT ADMIX (Armstrong ) /POWER n GROUT ADMIX (EBT) / CEBEX 100 (Fosroc )/ ZORIGROUT GP1 (PMCC) / SIKAGROUT ANCHKOR NSQ (Sika) /WATERSHIELD GROUT ADMIXi.e., 250 Grams per bag of 50 Kgs Cement add required water to make slurry form. d]. After completion of grouting, Remove the Rubber nozzles e]. Later sealing of the hole with polymer cement putty - ROOFCRETE AR (Armstrong ) / ZORIGROUT CMG (PMCC) / POWER n GUARD ARM (EBT) / WATERSHIELD AR / Fosroc NITOBOND AR + Cement. * FOR STRENTHENING AND SEAL THE POROSITY OF THE CONCRETE TO ARREST THE LEAKAGES, DAMPNESS, LEAKAGES OF CONSTRUCTION JOINTS: (FOR TERRACE /CEILING / RCC RETAINING WALLS BASEDMENT FLOORINGS / WATER TANKS / RESERVOIRS / TOILETS etc.,)

Painting with Ready mixed Synthetic Enamel paint in all shades -Grade-I having VOC (Volatile Organic Compound) content less than 50 grams/liter, approved colour and make including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete. … do … Two coats for old iron work

-do- Two coats for Internal walls for old work

Painting single coat for External walls old work with Acrylic Emulsion paint exterior grade with silicon additives having VOC (Volatile Organic Compound) content less than 50 grams/liter of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for external walls.

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM.

--do-- Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member.

--do-- Door Frame section of 63.5x100 MM . The two Vertical members are to be joined together with the horizontal member using 8x75 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member.

Providing and fixing 28 -30 MM thick solid Wood Polymer Composite(WPC) single extruded door shutter with 3MM top and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed to the frame using 3 inch /4 inch hinges. A minimum of 4 hinges will be required for fixing the door with the frame.

Supplying and fixing in position M.S Ornamental grills for windows and ventilators or for veranda openings using M.S. Flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with Two coats with Synthetic enamel paint over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Supplying and fixing in position Flush doors of different sizes with 30 mm thick Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping): of standard make Conforming to IS 2202 solid core flush doors , with one side Teak veneering and other side Commercial facing with hot pressed bonded with liquid phenol formaldehyde with rebate cutting, Double leaf using Best Indian Country wood (Vepa/Neredu) frames of size 65mmx100mm without threshold plate, including cost of M.S "Z" Hold fasts of 230 x 50 x 6mm, M.S Powder coated Butt hinges of 125 x 65 x 2.12mm, screws, nails, etc., complete, (excluding cost of other fixtures which will be paid separately but including labour charges for fixing the fixtures).

Supply and fixing of glow sign radium stickered Text / sign (or) picture of different sizes directly on the glass door partitions/Sheets/Floors/Roads/walk ways/walls etc., as directed during execution using glow sign radium stickers one layer including cost and conveyance of all materials etc., complete.

Supply of glow sign vinyl stickered name plate / sign (or) instruction boards using 4mm foam white sheet as back ground and glow sign vinyl sticker one layer for letters of different sizes as directed during execution including cost of 4mm foam sheet vinyl sticker and all labour charges for computer design and cutting, pasting and fixing the boards as directed during execution .

Hire charges for supply, erection and removal of digital design flex boards with frame work made with of 25mm x 25mm MS square pipe (light weight)with required back support to erect boards at specified places as directed by the department. The cost inclusive of materials, labour for printing, erection and removal square pipe (light weight) after completion of the function.

Supplying & Fixing Orissa Pan white glazed W.C of size 580 x 440 mm 1st quality ISI marked confirming to IS:2556-Part-3-1981 with "P" or "S" trap ISI Mark or equivalent brand approved by the department.

Supplying and Fixing European Water Closet of 1st quality confirming to IS:2556-Part-2-1973 of white glazed with 'S' trap with ISI mark or equivalent brand approved by the department

Supplying & Fixing white glazed flat back half stall urinals 590 x 375 x 380 mm 1st quality confirming to IS:2556-1995 with standard C.P. Spreader of overall size 95 x 95 x 57 mm confirming to IS:2556 - Part 6, Sec-6-1974 fixed with screws complete Indian make with ISI mark or equivalent approved by the department.

Supplying & Fixing Indian make Flat Back Wash Hand Basin of size 550 x 400 mm - Single C.P. Pillar cock 1st quality confirming to IS:2556-Part-4:1972 with ISI mark or equivalent approved by the department, with waste fittings like rubber plug, chain, 32 mm nominal size C.P. Fitting with parallel pipe thread confirming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams complete with standard CI brackets including wooden block

Supplying and Fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS 2548-1996

Supply & fixing of 10 Litres capacity Single Flush PVC low level system with internal components & short bend.

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" Flowgurard SDR 11 pipes are made from identical CPVC compounds having the same physical Properties for Hot and Cold Water (IS 15778:2007)

22.20 mm OD Pipe - SDR 11

28.60 mm OD Pipe - SDR 11

S & F Gunmetal (GM) Ball valve with SS Ball and SS Spindle as per IS - Class - I, Indian make heavy type - 50 mm NB Size

S & F Gunmetal (GM) Ball valve with SS Ball and SS Spindle as per IS - Class - I, Indian make heavy type - 25 mm NB Size

S & F Gunmetal (GM) Ball valve with SS Ball and SS Spindle as per IS - Class - I, Indian make heavy type - 20 mm NB Size

S & F Gunmetal Gate (GM peet) valve as per IS - 778 Class - I, Indian make heavy type - 80 mm NB Size

S & F Gunmetal Gate (GM peet) valve as per IS - 778 Class - I, Indian make heavy type - 25 mm NB Size

Engaging of SEMI SKILLED WORK MEN (2nd class ) carpenters / masons / plumbers / painters for maintainance works

Engaging of SEMI SKILLED WORK MEN (2nd class ) welder for maintainance works

Engaging of unskilled work man mazdoors/ woman mazdoor for maintainance works

Hire charges for welding set as directed during execution

Supply of welding electrodes 4mm dia

Supplying & fixing stainless steel sink size 36" x 18" (914.4x457.2mm)

Supply and hire charges for plant & machinery For Maintenance works by TRACTOR

Labour charges for fixing various sizes of G.I Chain links and tying in position to the posts / angles or supports with G.I wire including the cost of the G.I wire etc., complete as directed during execution ( excluding cost of G.I chain links angles, posts, bolts and nuts) and fixing with bolts and nuts to the angles.

Supply and fixing of CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS aluminium glazed partitions using 10MM CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS and 5.00 mm thick plain glass to full height. Using with LAM to a height of 0.91 meter at bottom panel and remaining height with glass and aluminium sections anodized to 12 to 15 microns and of sections of size 37mm x 62mm and 1.5mm thickness with one meter centre to centre duly fixed with clip beading on both sides including fixing the frame to pillars by M.S. flats, bolts and nuts including cost and conveyance of all materials etc., complete as directed during execution.

SPECIALISED POLYSULPHIDE / POLYURETHANE / HIGHBRED ACRYLIC /SEALANT TREATMENT TO THE OLD / EXISTING EXPANSION JOINT IN THE TERRACE, COLUMN, BEAM.

1.Cut and remove the existing expansion joint in the screed for a minimum width of 200 mm and a depth of screed ( up to the mother slab) by using diamond disc cutting machine and dispose the debris as per the department instruction. All elevated kerb wall both sides of the expansion joint along with the top free laying slab, cover etc as per the site conditions under the scope of the main contractor / client. 2.Remove the existing filling for a minimum depth of 40 mm using sharp knife (approximate size 25x 40 mm) as per the site condition. 3.If the site condition allows to insert backer rod, remove the existing filling for a minimum depth of 70 mm from the top ( the clear filling of sealant should be 40 mm) and insert MixCELL R inside the joint. 4.Clean the surface with air blower up to receive a dust free surface and make sure the surface is sound dry or the moisture content is less than 5 %. 5.Apply one coat of Penetrative Primer MixPRIME SB 300 and allow touching dry. 6.Fill the MixFLEX AC in the joint by using a sealant gun / notch trowel as per site condition up to the required depth and width and allow to dry for a minimum period of 1 day as per the climatic condition.

7.Apply two coat of penetrative sealer coat site mixed primer MixPRIME AC100 - mix with portable water and OP Cement in the ratio of 2:1:3 (Two part MixPRIME AC100 : One Part water : 3 Part OP cement by using slow speed mixer machine with paddle for a period of 2 to 3 minutes up to receive a homogeneous mix) @ 1.000 Liter per SQM in the entire screed removed portion ( vertical and horizontal faces) of 200 mm along with saturated ( saturated with MixPRIME AC100: Water: OP Cement in the ratio of 2:1:1) MixFELT P50 in between the two coats and allow to cure for a period of 6 hours. 8.Do the necessary levelling plastering with cement sand mortar 1:2:4 (6 mm aggregate) screed along with the addition of MixBOND SBR Super and PLAST FIBER 3S as per the following for a minimum thickness of removal. a.Mix the MixBOND SBR Super @ 2 Liter / Bag Cement in the ratio of 1:4 Mortar ( Pre mix the admixture in the portable water for preparing the mortar) b.Add 100 Gram PLASTFIBRE 3S in the above liquid and stirred well with a slow speed drill with paddle. c.Prepare the cement sand screed in the ratio of 1:2:4 with above prepared liquid for the suitable consistency. d.Necessary curing and drying for a minimum period of 4 days. 9.In wet condition, provide a dummy expansion joint on the top of the screed for a minimum size of 10 x 10 mm by using sharp trowel 10.Apply one coat of Penetrative Primer MixPRIME SB 300 in the entire surface of the dummy joint and allow to touch dry for a period of 30 minutes. Fill the MixFLEX AC in the joint by using a sealant gun / notch trowel as per site condition up to the required depth and width .