South Central Railway Tender

Supply and erection of Butterfly valve 200mm 5

Supply and erection of Non return valve 200mm

Supply and erection of Flow meter 150NB with fittings 150mm as per standard specification

Supply and erection of Electrically operated valve 150NB with fittings 150mm as per standard specification

Supply and running of 1.5 Sq.mm 6 core copper cable for Electronically controlled valve 9

Supply and running of 1.5 Sq.mm 6 core copper cable for control of flow meter.

Supply, installation and testing of Hydro pneumatic tank. With fittings and required piping and valve

"Design, install, testing and commissioning of SCADA for 500 Tab data analysis 11 including of desk top PC, LED display 32"" Keyboard, printer and licensed viewing system for Two integrated remote installed office PCs through team viewer through internet connection and allied accessories complete all as specified and as directed."

"Control panel (Inclusion of the following (i) to (ix) (i) Design, fabrication, transportation, supply, erection and commissioning of LT cubical panel 3 phase and neutral 415 V., 4 wire, free standing floor mounted, LT panel made up of 14 SWG CRCA (Cold rolled Carbon Annealed) sheet after seven tank process and painting with EPOXY powder coating. TPN (Triple Pole Neutral) tinned copper bus bar of sufficient capacity supported with DMC/AMC barriers and colour coded with heat shrinkable sleeves.The metering shall be provided as specified. The panel shall have short circuit with standing capacity of minimum 50 KA(RMS) power frequency test and consist of the switch gear as mentioned below. The panel shall be mounted on channels including supply and fixing as per specification. The complete work has to be carried out by the contractor including masonry work after 12 execution, all the feeder cables have to be connected to new panel with suitable cable hands as per the requirement of the Engineer at site. Air condition provision is to be made for entire control panel. The panel consists. ii. 1 No. of 400 A., 4 Pole, 36 KA MCCB (Molded Case Circuit Breaker) & 400 A change over for incoming. iii. 4 No. of 100 A., KA 4 pole MCCB out going. iv. 1 No. of 36 A., 10 KA pole MCB (Miniature Circuit Breaker) out going. v. 1 No. of 32 A., 10 KA 4 Pole MCB out going. vi. Along with multi functional digital meter similar to model No. EM-VIFPE of M/s HPL make with suitable ration CTs (Current Transformer) along with selector switches, LED phase indication pilot lamps (3 nos)and tinned copper bus bar of 1000 V along with rubber chequered sheets of size 1 m x length of panel of 12 mm thick as per IS 5424-1 No. Complete. vii. Suitable set of capacitor 40 KVAR with auto manual APF Relay. viii. VFD (Variable Frequency Drive) 3 No. PLC 3 No. HMI, with pressure treasures. ix. Suitable 40 HP star delta starter with auto manual selection mode- 3 no's. And same starter will work on VFD and command will be to VFD by PLC(Programmed Logic Control)"

Fabrication and erection of 14 SWG CRCA sheet steel enclosure of suitable size for indoor panel with Double Door as per IS/IEC 61439. including cutting, bending drilling, welding and reveting etc, complete with cleaning with 7 tank process and painting with EPOXY powder coating including cost and conveyance of all materials and labour charges. The MDBs shall be mounted on suitable required size of CC plinth (CC plinth cost will be paid separately) and secured with bolts, nuts and washers as advised by Engineer at site. The panel comprising of 100A tinned Copper Bus Bar as per IS 613: 2000 or latest required shape supported with appropriate DMC / SMC barriers and colour coded with heat shrinkable sleeves,LT 3 Phase Digital Multifunction energy meter with 3 lines LCD 13 display for measuring all the parameters( Voltage/ Current/ Power/Frequency/power factor /kw/kwh/ kvar/kvarh) , Current T/Fs, indication lamps for incoming & outgoing feeders. suppot insulatorS, neutral links,Incoming & outgoing terminals,suitable cable termination glands , grommets, lugs, connecting wires and all other accessories suit with the following switchgear and accessories. The cables should be properly terminated in the switchgears with necessary lugs and all necessary accessories complete.The panel should comprise of the following Switchgear. Makes: ABB/Seimens/L&T/ Schneider /Legrand/Havells/Indo-Asian.(Drawing approval to be taken prior to supply) 2. Thermamagnetic based 63A, 4 Pole MCCB with Icu = 36kA capacity, as per IEC 60947-2 make suitable spreader links(set of 8)-01 nos 3. 32 A DP MCB C Curve 10KA as per IS/IEC60898-1 - 4no's.

Design, Fabrication and supply of 16 watts LED catwalk lights (10w+4w+2w) 1 aluminum Die Cast with IP67 Protection necessary hardware material suitable to work one 24 V DC/48V AC 3 Dimensional type for pit lighting as per latest CEE Specification including all accessories Note Prior Approval to be taken . LED catwalk light fitting 5 years warranty.

Erection of 16 watts LED Catwalk lights (10w+4w+2w) to the water hydrants with required clamps, rag bolts and nuts complete.

Design, Supply & Erection of Control panel Unit containing 3 Nos. SMPS POWER UNITS enclosed in sheet steel enclosed with all connected safety accessories, Indications & Controls, dedicated for the High Power LED based 16 W LED Pit/Catwalk lights as per following specification 3 PANEL containing 3 Nos of SMPS units. Each will be suitable for 7 Nos. of pit/catwalk lights total 7x3=21 Nos of pit/catwalk lights Specification for each SMPS Unit: MODEL# OSSE/SMPSU/)1/24/10A/13, MAKE: OSSE, input Voltage: 180V to 260Volts, Output Voltage:24 Volts DC +/- 1% Regulation -CV Output Current:10Amps Each SMPS Protection: Short Circuit Proof: Over Voltage Protection, Ripple:< 200mV including all accessories

Supply and fixing of TPN DB's,4 way 8+ 12 module IP 30-IK08 of model no.5076 60 of legrand make or its equivalent in

Supply and erection of 32A, C-curve 3P MCBs with 10KA breaking capacity of only with all necessary accessories complete.

Supply, stringing and run of 2 core 10.0 sqmm, 1100 V PVC insulated aluminium conductor wires along with 10 SWG PVC coated GI stay wire and separators as per instruction of field Engineer

Supply and running of 4 sqmm PVC insulated single core multistranded aluminum wire in PVC pipes

Supply of 4 core 150 sqmm XLPE insulated underground armoured aluminium cable with heat resistant insulation as per IS 7098(Part 1)1988.

Laying of 4 core LTUG cable of size 120 sqmm and above in the trench and connected at both the ends complete.

Supply of LTUG 4 core 25 sqmm XLPE insulated PVC sheathed Aluminium armoured cable as per IS 7098(Part 1)1988 or latest amendment.

Supply of 1.1 KV Grade 4 core 16 sqmm XLPE insulated PVC sheathed Aluminium armoured cable as per IS 7098(Part 1)1988 or latest amendment .

Laying of 4 core LTUG cable up to size 25 sqmm in the trench and connected at both the ends complete. 13

Supply and running of 8 SWG GI earth continuity wire complete with connections.

Supply fixing, of HDPE pipe of 50 mm outer dia of PE-100,PN6 class as per IS 4984: 2016 or latest with suitable couplings and clamps for cable laying with all necessary accessories complete.

Supply and laying of PE 63 grade HDPE pipe of size 40mm(outer dia)PN8 with necessary Couplings, clamps, brackets nuts bolts and all necessary accessories for fixing to wall/structure complete.

Supply fixing, of HDPE pipe of 75 mm outer dia of PE-100,PN6 class as per IS 4884: 2016 or latest with suitable couplings and clamps for cable laying with all necessary accessories complete.

Supply fixing, of HDPE pipe of 25 mm outer dia of PE-100,PN 12.5 (SDR 11) class as per IS 4984-2016 or latest amendment with suitable couplings and clamps for cable laying with all necessary accessories complete.

Excavation of cable trench in all types soil of size of size 400mm wide x 1 mtr. deep, 18 and making good of the same to its original form and shape after complete including all connected materials and works up to the satisfaction of the Engineer at Site.The exact route of the HT/LT cable is to be decided in consultation with Engineer in charge.

Excavation of cable trench duly breaking the existing cement concrete flooring and filling with layer of sand bricks etc.,as per the standards of cable laying (A minimum of 1mtr depth 19 and 400 mm width) and filling the trench with soil duly ramming etc.The flooring shall be made good with cement concrete as original by the contractor after completion of trenching work up to the satisfaction of the Engineer at Site.The exact route of the HT/LT cable is to be decided in consultation with Engineer in charge.

Excavation of cable trench in hard soil of size of size 400mm wide x 1 mtr. deep, andmaking good of the same to its original form and shape after complete including all connected materials and works.

Excavation of cable trench of size 400mm x 1 mtr deep track X-ing/Road X-ing and making good of the same to its original form and shape completely including all connected materials and works. 22

Supply of LED of 24W LED Street light fitting as per CEE spec

Fixing and commissoning of LED St light fitting with 1.2mtr./required length of 'B'grade GI pipe/Bracket(as necessary) of 2" dia/suitable dia with clamps, bolts and nuts etc. Including internal connection complete.

Earthing arrangements as per standard specifications and drawing enclosed including 24 digging earth pit, electrode EARTH BOX with reinforced concrete complete with all other connected materials and works including connecting the earth electrode and aerial earthing according to IS 3043 and RDSO drawing ETI/OHE/P/7021 in other than substations.

Supply fixing and connecting of Cable Junction Boxes IP 66 with metric knockouts for 25 cable entry Cable junction boxes of model no. DK 2525 G of Hensel make or equivalent in sintex/legrand conforming to IS:13573/92,IEC 60947-3 with necessary terminals suitable for cables upto 25 Sq mm and all necessary accessories complete.

Supply fixing and connecting of Cable Junction Boxes IP 55 / IP 65 with metric 26 knockouts for cable entry Cable junction boxes of model no. K 1204 of Hensel make or equivalent in sintex/legrand with necessary terminals suitable for cables upto 150Sq mm and all necessary accessories complete.