Public Health And Municipal Engineering Department Tender

Vibrated Reinforced Cement Concrete M 25 Design Mix (by weigh batching) using 20mm size (SS-5) hard blasted Trap machine crushed graded metal (Coarse aggregate) from approved quarry, using a minimum quantity of 350 kgs. of cement per 1 cum of concrete including cost and conveyance of all materials like cement, fine aggregate (Sand), coarse aggregate, water etc., to site and cost of all materials including centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates, etc., shuttering , machine mixing, laying concrete, vibrating, lift charges, curing etc complete but excluding cost of steel and it’s fabrication charges for finished item of work but excluding seigniorage charges (APSS No. 402 & 403)

a) For columns footings Add for sundries

b) For Columns below GL Add for sundries

c) For Columns above GL Add for sundries

d) For Plinth beam above GL Add for sundries

e) For Roof beams Add for sundries

f) For Roof Slab Add for sundries

g) For Septik tank base slab Add for sundries

h) For Septik tank side walls For scum board & baffle wall Add for sundries

i) For Septik tank top slab Add for sundries

Providing High Yield Strength Deformed (HYSD) steel bars (Fe-500 grade as per IS 1786-1985) of 8mm to 40mm diameters, cutting, bending, to required sizes and shapes placing in position with cover blocks of approved size and binding wire of 20SWG, forming grills for reinforcement work as per approved Designs and drawings including cost and conveyance of bars from approved sources to site of work, including cost and conveyance of binding wire, cover blocks, chairs, overlaps, spacers, dowels, wastage etc., and all operational, incidental, and labour charges such as cutting, bending, placing in position, tying etc., and sales & other taxes,on cost of all materials complete for finished item of work (APSS No.126) in all floors. For Footings @ 90 Kgs/cubic meter For Columns @ 90 Kgs/cubic meter For Plinth beam above GL @ 90 Kgs/cubic meter For Roof beams @ 90 Kgs/cubic meter For Roof Slab @ 90 Kgs/cubic meter For Septik tank base slab @ 90 Kgs/cubic meter For Septik tank side walls @ 90 Kgs/cubic meter For Septik tank top slab @ 90 Kgs/cubic meter

Brick Masonary 2nd Class Ground moulded or treditional size 23x11x7 Cm in Cement Mortor (1:6) Prop including Cost & conveyance of all Materials like Cement, Sand, Bricks, Water, etc., to site cost of all materials, including all labour charges like mixing Cement Mortor, scaffoding charges lift charges , curing charges etc., complete for finished item of work

1 Below Ground level a. alround the toilet block b. Middle short wall c.Curtain wall d. Partion walls (G - Toilet) e. Partion short wall (G - Toilet) f. Partion walls (L - Toilet) g. Partion short wall (L - Toilet) Add for sundries

II. Super structure alround the toilet block Middle short wall Curtain wall Partion walls (G - Toilet) Partion short wall (G - Toilet) Partion walls (L - Toilet) Partion short wall (L - Toilet) Add for sundries

Providing and fixing 30mm thick BRAND FACTORY MADE BOTHSIDE PRELAM SOLID PANEL PVC DOOR SHUTTER consisting of frame made out of MS. Tubes of 19gauge thickness and size of 19mmX19mm for stiles, top and bottom rails. MS. Frame shall have a coat of steel primers of approved make and manufacture. MS. Frame covered with 5mm thick heat moulded Prelam Pac „C‟ channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 450 angle on either side forming stiles; and 5mm thick, 95mm wide Prelam Pac sheet out of which 75mm shall be flat and 20mm shall be tapered in 450 on the inner side to form top and bottom rail 115mm wide Prelam Pac sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rail shall be provided either side of the panel. 10mm (5mmX2) thick, 20mmwide cross Pac sheet shall be provided as gap insert for top and bottom rail. Panelling of 5mm thick both side Prelam Pac sheet to be fitted in the MS. Frame welded/ sealed to the stiles & rails with 7mm(5mm+2mm) thick X 15mm wide Pac sheet beading on inner side, and joined together with solvent cement adhesive etc. an additional 5mm thick Pac strip of 20mm width is to be stuck on the interior side of the „C‟ channel using Pac solvent cement adhesive etc. complete as per direction of Engineer – in-charge, manufacture specification and drawing. For Gents Toilet For Ladies Toilet

Supply and fixing Aluminium Anodised Casement windows as per approved drawing with aluminium anodised sections of Series C Jindal Hollow sections and outer frame of 8804 of size 46 x 44 mm, Shutter frame of 8802 of size 44 mm x 46 mm and Mullion frame of 8803 of size 59 x 38 and glazing section of 4433 with plain clear float glass 6 mm thick fixed including supply and fixing aluminium powder coated 1 No.of casement friction stay hinges for each shutter, 1 Nos. aluminium handles of 150 mm for each shutter and all labour charges for fixing the fixtures with required no.of screws, bolts and nuts and including labour charges for fixing the frame in position, fixing shutter to frame etc. completed for finished item of work For Gents Toilet For Ladies Toilet

Plastering with 20mm thick in single coat in CM (1:4) finished smooth including cost and conveyance of all materials to site of all materials, finishing, curing, scaffolding and all operational, incidental, labour charges etc., including cutting grooves where ever necessary etc., complete for finished item of work. (As per SS 903). alround the toilet block Middle short wall Curtain wall Partion walls (G - Toilet) Partion short wall (G - Toilet) Partion walls (L - Toilet) Partion short wall (L - Toilet) Add for sundries

Plastering with 12mm thick in single coat in CM (1:3) finished smooth including cost and conveyance of all materials to site of all materials, finishing, curing, scaffolding and all operational, incidental, labour charges etc., including cutting grooves where ever necessary etc., complete for finished item of work. (As per SS 903). alround the toilet block Middle short wall Curtain wall Partion short wall (G - Toilet) Partion walls (L - Toilet) Partion short wall (L - Toilet) Parapetwall Add for sundries

Supply, Installation and commissioning approved make floor mounted Close coupled EWC suit CASCADE model 'P' or 'S' trap with dual flush porcelain cistern fixed on EWC with all internal parts of dual flush cistern, ultra solid seat cover of approvedmake with rubber buffer and cap 15 mm angle stop cock 450 mm long PVC inter connection pipe wall flanges all of approved make etc. complete for finished item of work in all respects:White Colour

Supplying & Fixing white glazed flat back half stall urinals1st quality conforming to IS:2556-1995 with standard C.P. Spreader of overall size 95 x 95 x 57 mm conforming to IS:2556-Part6, Sec-6-1974 fixed with screws complete Indian make : 590 x 375 x 390 mm BMW-D.35

Supplying & Fixing Indian make Flat Back Wash Hand Basin 1st quality conforming to IS:2556-Part-4:1972 with waste fittings like rubber plug, chain, 32 mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams 12.70mm PVC pipe connections with lip ring UPVC,12.70mm brass bib cock, pedestal , 32mm dia wast pipe , 38mm dia PVC waiste coupling , 32mm dia PVC bottle trap Seiko/ Senior/ Nice/ Esso or equivalent complete with standard CI brackets including wooden block: 450 x 300 mm - Double C.P. Pillar cock

Construction of 457.20mm x 457.20mm inspection chamber with brick masonry using 2nd class modular size (19x9x9cm) in CM (1:6) prop. upto a depth of 914.40mm including excavation in all types of soils laying 100mm thick plain CC (1:5:10) prop. bed making channel in plain CC (1:2:4) prop. 12mm thick plastering in CM (1:4) prop. to inside & outside walls & fitted with light weight 457.2 mm x 457.2 mm (1'6"x1'6") C.I frame and cover of 20 Kg including cost ,, conveyance complete as per special specification and as directed by Engineer-in-charge for finished item of work.

Suply & fixing of 12.70mm NP Bib tap of Indian make heavy duty Seiko/ Senior/ Nice/ Senior/ Nice or equivalent at all levels including cost & conveyance, seignarage , sales tax royalties of all materials, labour charges for finished item of work as per special specification and as directed by the Engineer-in-charge for finished item of work.

Suply & fixing of 12.70mm angle stop cock Indian make heavy duty Seiko/ Senior/ Nice/ Senior/ Nice or equivalent at all levels including cost & conveyance, seignarage, sales tax royalties of all materials, labour charges for finished item of work as per special specification and as directed by the Engineer-in-charge for finished item of work.(for WashBasin)

Providing and placing on pedestal polythelene water storage tank with double layer approved brand with cover and suitable locking arrage-ments making necessary holes for inlet and out let arrangments and over flow pipes but without fittings etc complete

Manufacture, Supply and Delivery of Unplasticised PVCs Pipes for potable water supplies conforming to IS : 4985/2000 (3rd revision) with bell ends (Socket) as per specification in light Grey/Natural Ivory Grey/ Any other Color (except White) inclusive of transportation to the sub-divisional stores anywhere in AP excluding all taxes (110mm Dia 6kg/cm2 Pvc Pipe)

Manufacture, Supply and Delivery of Unplasticised PVCs Pipes for potable water supplies conforming to IS : 4985/2000 (3rd revision) with bell ends (Socket) as per specification in light Grey/Natural Ivory Grey/ Any other Color (except White) inclusive of transportation to the sub-divisional stores anywhere in AP excluding all taxes (75mm Dia 6kg/cm2 Pvc Pipe)

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and areproduced in CTS (Copper Tube Sizes 1/2" ton 2" AshirvadFlowgurard SDR 11 and SDR 13.5 pipes are made from idential CPVC compounds having the same physical Proper ties for Hot and ColdWater(IS15778:2007) 28.60mm OD Pipe -SDR 13.5

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and areproduced in CTS (Copper Tube Sizes 1/2" ton 2" AshirvadFlowgurard SDR 11 and SDR 13.5 pipes are made from idential CPVC compounds having the same physical Proper ties for Hot and ColdWater(IS15778:2007) 34.90mm OD Pipe -SDR 13.5

Painting to new walls with 2 coats of plastic emulsion paint of approved brand over 1 coat of Cement Primer and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete for finished item of work as per SS 911 for internal walls Inside Plastering

Painting to New walls with two coats of acrylic emulsion paint weather proof waterbased, modified acrylic with silicon additives exterior grade having VOC (Volatile Organic Compound ) content less than 50 grams/ liter of superior quality of approved brand and shade over base coat of cement primer grade -I making three coats in all to give an even shade after thoroughly brushing the surface to remove all loose powdered materials, including cost and conveyance of all materials, including cost and conveyance of all materials, cost of brushes, water to site, etc., sales & other taxes, all operational, incidental and labour charges such as scaffolding charges, lift charges, curing etc., complete for finished item of work in all floors for Walls.(APSS No. 911) in All Floors EXTERNAL WALLS Outside Plastering