Panchayat Raj Engineering Department Tender

Manufacture, Supply, & Delivery of HDPE Pipes conforming to IS 4984 - 2016 including transportation to anywhere in A.P,excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%. (Supply up to 90 mm dia. in coil & above 90 mm dia. straight length.) 110 mm dia 6 Kg /Cm² HDPE Pipe

Manufacture, Supply, & Delivery of HDPE Pipes conforming to IS 4984 - 2016 including transportation to anywhere in A.P,excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%. (Supply up to 90 mm dia. in coil & above 90 mm dia. straight length.) 140 mm dia 6 Kg /Cm² HDPE Pipe

Manufacture, Supply, & Delivery of HDPE Pipes conforming to IS 4984 - 2016 including transportation to anywhere in A.P,excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%. (Supply up to 90 mm dia. in coil & above 90 mm dia. straight length.) 160 mm dia 6 Kg /Cm² HDPE Pipe

Earth Work excavation and depositing on bank with an initial lead of 10 meters and lift of 2.00 meters in all types of soils except hard rock requiring blasting for pipeline and lowering and laying of H.D.P.E Pipes into trench placing them true to alignment and gradient, jointing the H.D.P.E pipes, specials and fixing of valves with bolts and nuts and rubber packings, filling of pipes with water with an initital lead of 500m and testing the pipeline to the required pressure and make it leak proof, refilling the trench with excavated earth excluding cost and conveyance of pipes and including all other charges 63 mm x 6 Kg/Sq.cm HDPE Pipe (PE 100 Grade) , Trench of size 0.70 x 1.0 m with 2/3rd machinary and 1/3rd manual

Earth Work excavation and depositing on bank with an initial lead of 10 meters and lift of 2.00 meters in all types of soils except hard rock requiring blasting for pipeline and lowering and laying of H.D.P.E Pipes into trench placing them true to alignment and gradient, jointing the H.D.P.E pipes, specials and fixing of valves with bolts and nuts and rubber packings, filling of pipes with water with an initital lead of 500m and testing the pipeline to the required pressure and make it leak proof, refilling the trench with excavated earth excluding cost and conveyance of pipes and including all other charges 75 mm x 6 Kg/Sq.cm HDPE Pipe (PE 100 Grade) , Trench of size 0.70 x 1.0 m with 2/3rd machinary and 1/3rd manual

Earth Work excavation and depositing on bank with an initial lead of 10 meters and lift of 2.00 meters in all types of soils except hard rock requiring blasting for pipeline and lowering and laying of H.D.P.E Pipes into trench placing them true to alignment and gradient, jointing the H.D.P.E pipes, specials and fixing of valves with bolts and nuts and rubber packings, filling of pipes with water with an initital lead of 500m and testing the pipeline to the required pressure and make it leak proof, refilling the trench with excavated earth excluding cost and conveyance of pipes and including all other charges 90 mm x 6 Kg/Sq.cm HDPE Pipe (PE 100 Grade) , Trench of size 0.70 x 1.0 m with 2/3rd machinary and 1/3rd manual

Earth Work excavation and depositing on bank with an initial lead of 10 meters and lift of 2.00 meters in all types of soils except hard rock requiring blasting for pipeline and lowering and laying of H.D.P.E Pipes into trench placing them true to alignment and gradient, jointing the H.D.P.E pipes, specials and fixing of valves with bolts and nuts and rubber packings, filling of pipes with water with an initital lead of 500m and testing the pipeline to the required pressure and make it leak proof, refilling the trench with excavated earth excluding cost and conveyance of pipes and including all other charges 110 mm x 6 Kg/Sq.cm HDPE Pipe (PE 100 Grade) , Trench of size 0.70 x 1.0 m with 2/3rd machinary and 1/3rd manual

Earth Work excavation and depositing on bank with an initial lead of 10 meters and lift of 2.00 meters in all types of soils except hard rock requiring blasting for pipeline and lowering and laying of H.D.P.E Pipes into trench placing them true to alignment and gradient, jointing the H.D.P.E pipes, specials and fixing of valves with bolts and nuts and rubber packings, filling of pipes with water with an initital lead of 500m and testing the pipeline to the required pressure and make it leak proof, refilling the trench with excavated earth excluding cost and conveyance of pipes and including all other charges 140 mm x 6 Kg/Sq.cm HDPE Pipe (PE 100 Grade) , Trench of size 0.70 x 1.0 m with 2/3rd machinary and 1/3rd manual

Earth Work excavation and depositing on bank with an initial lead of 10 meters and lift of 2.00 meters in all types of soils except hard rock requiring blasting for pipeline and lowering and laying of H.D.P.E Pipes into trench placing them true to alignment and gradient, jointing the H.D.P.E pipes, specials and fixing of valves with bolts and nuts and rubber packings, filling of pipes with water with an initital lead of 500m and testing the pipeline to the required pressure and make it leak proof, refilling the trench with excavated earth excluding cost and conveyance of pipes and including all other charges 160 mm x 6 Kg/Sq.cm HDPE Pipe (PE 100 Grade) , Trench of size 0.80 x 1.0 m with 2/3rd machinary and 1/3rd manual

Earth Work excavation and depositing on bank with an initial lead of 10 meters and lift of 2.00 meters in all types of soils except hard rock requiring blasting for pipeline and lowering and laying of H.D.P.E Pipes into trench placing them true to alignment and gradient, jointing the H.D.P.E pipes, specials and fixing of valves with bolts and nuts and rubber packings, filling of pipes with water with an initital lead of 500m and testing the pipeline to the required pressure and make it leak proof, refilling the trench with excavated earth excluding cost and conveyance of pipes and including all other charges 63 mm x 6 Kg/Sq.cm HDPE Pipe (PE 100 Grade) , Trench of size 0.70 x 1.0 m manually

Earth Work excavation and depositing on bank with an initial lead of 10 meters and lift of 2.00 meters in all types of soils except hard rock requiring blasting for pipeline and lowering and laying of H.D.P.E Pipes into trench placing them true to alignment and gradient, jointing the H.D.P.E pipes, specials and fixing of valves with bolts and nuts and rubber packings, filling of pipes with water with an initital lead of 500m and testing the pipeline to the required pressure and make it leak proof, refilling the trench with excavated earth excluding cost and conveyance of pipes and including all other charges 75 mm x 6 Kg/Sq.cm HDPE Pipe (PE 100 Grade) , Trench of size 0.70 x 1.0 m manually

Earth Work excavation and depositing on bank with an initial lead of 10 meters and lift of 2.00 meters in all types of soils except hard rock requiring blasting for pipeline and lowering and laying of H.D.P.E Pipes into trench placing them true to alignment and gradient, jointing the H.D.P.E pipes, specials and fixing of valves with bolts and nuts and rubber packings, filling of pipes with water with an initital lead of 500m and testing the pipeline to the required pressure and make it leak proof, refilling the trench with excavated earth excluding cost and conveyance of pipes and including all other charges 110 mm x 6 Kg/Sq.cm HDPE Pipe (PE 100 Grade) , Trench of size 0.70 x 1.0 m manually

Cutting open C.C. road surface with concrete saw cutter and removal with Breaker including labour charges (SSR Sl No 25 b PH item)

Plain Cement concrete (1:2:4) Nominal Mix using 20mm metal using concrete mixer for CC Road cutting Gap Filling

CC Road Cutting and Earth Work excavation and depositing on bank with an initial lead of 10 meters and lift of 2.00 meters in all types of soils except hard rock requiring blasting for pipeline and lowering and laying of H.D.P.E Pipes into trench placing them true to alignment and gradient, jointing the H.D.P.E pipes, specials and fixing of valves with bolts and nuts and rubber packings, filling of pipes with water with an initital lead of 500m and testing the pipeline to the required pressure and make it leak proof, refilling the trench with excavated earth excluding CC Cutting Depth excluding cost and conveyance of pipes including all other charges 63 mm x 6 Kg/Sq.cm HDPE Pipe (PE 100 Grade) , Trench of size 0.50 x 0.80 m with 2/3rd machinary and 1/3rd manual

CC Road Cutting and Earth Work excavation and depositing on bank with an initial lead of 10 meters and lift of 2.00 meters in all types of soils except hard rock requiring blasting for pipeline and lowering and laying of H.D.P.E Pipes into trench placing them true to alignment and gradient, jointing the H.D.P.E pipes, specials and fixing of valves with bolts and nuts and rubber packings, filling of pipes with water with an initital lead of 500m and testing the pipeline to the required pressure and make it leak proof, refilling the trench with excavated earth excluding CC Cutting Depth excluding cost and conveyance of pipes including all other charges 75 mm x 6 Kg/Sq.cm HDPE Pipe (PE 100 Grade) , Trench of size 0.50 x 0.80 m with 2/3rd machinary and 1/3rd manual

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or equivalent as per IS:1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The valves should be Vacuum tight and 100% leak proof with face to face dimensions as per BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS:1538, construction of RCC valve chambers as per requirement with RCC slab and RCC manhole cover with locking arrangements etc., complete for finished item of work. The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of work, but excluding GST and seignourage charges as specified in Technical specifications including overheads and Contractor's profit @ 13.615%.

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or equivalent as per IS:1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The valves should be Vacuum tight and 100% leak proof with face to face dimensions as per BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS:1538, construction of RCC valve chambers as per requirement with RCC slab and RCC manhole cover with locking arrangements etc., complete for finished item of work. The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of work, but excluding GST and seignourage charges as specified in Technical specifications including overheads and Contractor's profit @ 13.615%.

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or equivalent as per IS:1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The valves should be Vacuum tight and 100% leak proof with face to face dimensions as per BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS:1538, construction of RCC valve chambers as per requirement with RCC slab and RCC manhole cover with locking arrangements etc., complete for finished item of work. The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of work, but excluding GST and seignourage charges as specified in Technical specifications including overheads and Contractor's profit @ 13.615%.

Construction of 40 KL capacity OHSR of 12.90 mts staging with M30 grade design mix at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils in wet or dry conditions for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SOR . The rate is inclusive of cost of all materials and labour charges and all taxes, duties and levies, etc., complete for finished item of work, but excluding GST and Seigniorage charges, including Overheads 1). All concrete members shall be designed with M30 grade design mix. 2) Rate is for OHSRs with RAFT FOUNDATION 3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof. 4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 200 KMPH and SBC 10T/Sqm. Fixtures include : a) RCC or Aluminium ladder inside 0.60 m wide. b) Spiral staircase on the outside shall be provided upto 200 KL. c) Lightening arrestor, including conductor and earthling etc.,d) RCC ventilators with copper or stainless steel fly proof mesh. e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos. f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No. g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab. j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends

CI Vertical connections and Specials for OHSR (The rates are inclusive of verticals for all inlet, out let, overflow and scour connections(as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30)

Construction of Functional Household Tap Connections (FHTC) on 63 mm dia main with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 1/2" service connection) and Regulating brass ferrule of pressure rating PN 10,including testing of all materials, labor, inspection charges, transportation up to site, transit insurance, loading, unloading, stacking and fixing etc., complete as specified and directed by the departmental Engineer in charge and compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2") including supply, delivery and fixing of 12.7mm dia Brass Bib cock(short body) Indian make heavy duty tap of weight 155-165 gm excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Manufacture, Supply & delivery of 20mm OD HDPE pipe 16.0 kg/sqcm conforming to IS 4984-2016 of PE-100 grade material along with all fittings, including cost of materials, manufacturing, loading, unloading, stacking, transit Insurance, transportation excluding all taxes including Laying, Jointing of 20mm dia HDPE pipes as per BIS No.7634 part-II/75 ( including trench excavation upto 0.5 mts depth including testing, refilling etc., complete)excluding GST but including contractor' profit & overheads @ 13.615%.

Cost, supply & fixing of 15 mm Nominal Bore GI Pipe Medium Grade properties & weight as per IS 12391 ISI mark with GI Fittings including the cost of pipe & its fittings, labour charges etc complete excluding GST but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 75 mm dia main with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 1/2" service connection) and Regulating brass ferrule of pressure rating PN 10,including testing of all materials, labor, inspection charges, transportation up to site, transit insurance, loading, unloading, stacking and fixing etc., complete as specified and directed by the departmental Engineer in charge and compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2") including supply, delivery and fixing of 12.7mm dia Brass Bib cock(short body) Indian make heavy duty tap of weight 155-165 gm excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Manufacture, Supply & delivery of 20mm OD HDPE pipe 16.0 kg/sqcm conforming to IS 4984-2016 of PE-100 grade material along with all fittings, including cost of materials, manufacturing, loading, unloading, stacking, transit Insurance, transportation excluding all taxes including Laying, Jointing of 20mm dia HDPE pipes as per BIS No.7634 part-II/75 ( including trench excavation upto 0.5 mts depth including testing, refilling etc., complete)excluding GST but including contractor' profit & overheads @ 13.615%.

Cost, supply & fixing of 15 mm Nominal Bore GI Pipe Medium Grade properties & weight as per IS 12391 ISI mark with GI Fittings including the cost of pipe & its fittings, labour charges etc complete excluding GST but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 110 mm dia main with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 1/2" service connection) and Regulating brass ferrule of pressure rating PN 10,including testing of all materials, labor, inspection charges, transportation up to site, transit insurance, loading, unloading, stacking and fixing etc., complete as specified and directed by the departmental Engineer in charge and compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2") including supply, delivery and fixing of 12.7mm dia Brass Bib cock(short body) Indian make heavy duty tap of weight 155-165 gm excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Manufacture, Supply & delivery of 20mm OD HDPE pipe 16.0 kg/sqcm conforming to IS 4984-2016 of PE-100 grade material along with all fittings, including cost of materials, manufacturing, loading, unloading, stacking, transit Insurance, transportation excluding all taxes including Laying, Jointing of 20mm dia HDPE pipes as per BIS No.7634 part-II/75 ( including trench excavation upto 0.5 mts depth including testing, refilling etc., complete)excluding GST but including contractor' profit & overheads @ 13.615%.

Cost, supply & fixing of 15 mm Nominal Bore GI Pipe Medium Grade properties & weight as per IS 12391 ISI mark with GI Fittings including the cost of pipe & its fittings, labour charges etc complete excluding GST but including contractor' profit & overheads @ 13.615%.

Construction of Functional Household Tap Connections (FHTC) on 160 mm dia main with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 1/2" service connection) and Regulating brass ferrule of pressure rating PN 10,including testing of all materials, labor, inspection charges, transportation up to site, transit insurance, loading, unloading, stacking and fixing etc., complete as specified and directed by the departmental Engineer in charge and compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2") including supply, delivery and fixing of 12.7mm dia Brass Bib cock(short body) Indian make heavy duty tap of weight 155-165 gm excluding GST and seigniorage charges but including contractor' profit & overheads @ 13.615%.

Manufacture, Supply & delivery of 20mm OD HDPE pipe 16.0 kg/sqcm conforming to IS 4984-2016 of PE-100 grade material along with all fittings, including cost of materials, manufacturing, loading, unloading, stacking, transit Insurance, transportation excluding all taxes including Laying, Jointing of 20mm dia HDPE pipes as per BIS No.7634 part-II/75 ( including trench excavation upto 0.5 mts depth including testing, refilling etc., complete)excluding GST but including contractor' profit & overheads @ 13.615%.

Cost, supply & fixing of 15 mm Nominal Bore GI Pipe Medium Grade properties & weight as per IS 12391 ISI mark with GI Fittings including the cost of pipe & its fittings, labour charges etc complete excluding GST but including contractor' profit & overheads @ 13.615%.