Panchayat Raj Engineering Department Tender

Cost and supply of 175mm MS clampset

Cost and supply of 180 mm dia PVC bore cap

Cost and supply of 175 mm dia MS Bail Plug

Provision for Geological Survey charges including all labour charges etc. complete.

Supply and Transportation of 10.00 HP 12-16 stage, 5star rated submersible motor pumpset, confirming to IS 8034 and motor confirming to IS 9283 with waterproof winding, Pump shall be suitable for various delivery head and discharge with stainless steel shaft. Motor suitable for working on 415V ± 10%, Three Phase 50 Hz AC supply etc complete for 6" Bore well. Makes : Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha/Falcon excluding Taxes but inclusive of CP @13.615%

Supply of 3 Core 4.0 sqmm Flat Copper cable of ISI for Submersible Motors confirming to IS:694:1990. Makes : As per list of recommended brands as category I( Y- I Makes: Finolex / RR Kabel/ Polycab / Havells / KEI/ Gloster/ Goldmedal / GM/ Finecab/ Million)

Supply Installation Testing and commissioning of self-healing MPP/MP type shunt capacitor (banks) conforming to IS:13340-41 / IEC :831-1&2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector ( PSD ) and shall have dissipation factor less than 0.0025 at 50 Hz and total wattage loss less than 0.5 Watt per KVAR. including making connections with suitable capacity conductors/cables testing as required.Standard duty Single phase 250 V / Three phase 440 V, 50 Hz capacitor (Bank)

Manufacture, Supply, & Delivery of 75mm dia 8 kgs HDPE Pipe conforming to IS 4984 - 1995 including transportation to anywhere in A.P, excluding all taxes

Fabrication ,transportation and and supply of wall mounted control Panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using L&T / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets.Voltmeter ;. Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab Ammeter Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab Single phase preventor Makes: L&T / Minilec / Powertec. 32 A TP, 10KA MCB. Makes: Legrand / Schneider capacitor Makes: L&T / Siemens / Schneider / Epcos/Havells. Voltmeter ; 0-500 V 96x96mm size. 0 to 20 Amps / 0 50 Amps Ammeter (96x96mm size)-1No. Single phase preventor of suitable range - 1No. 32 A TP, 10KA MCB. - 1No Indication lamps (R-Y-B) with switch control - 1set , Voltmeter & Ammeter selector switch - 2 Nos , Supply and fixing of ISI Mark suitable capacitor Upto 7.5 HP with DOL Starter excluding taxes but inclusive of CP 13.615%

Cost and Supply of 56/0.30mm (4.00sqmm) PVC insulated 1100V grade as per IS: 694/1990 specifications for Copper Cable including all taxes.

Labour charges for Errection of Submersible Motor and Pump set including all labour charges etc. complete.

Construction of pipelines for water supply with HDPE Grade pipes as per IS 4984 - 1995 specifications, with its amendments and revisions thereon including supplying of pipes, necessary specials such as bends, Tees, etc. lowering, laying and jointing of pipe lines true to alignment and gradient, trench of Size 0.70 x 1.00 mt. depth excavation for pipelines in all soils except rock requiring blasting and refilling trenches with excavated earth 2/3rd machinery and 1/3rd manual (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and fillig the pipeline with waterand testing etc., complete. The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work, but excluding taxes. 90 mm dia HDPE-6Kg/cm. 2/3rd machinery and 1/3rd manua

House service connections (PP Saddle) PP excluding GST Clamp saddles-PP clamp Saddles shall be maunfactured by injection moulding using virgin polypropylene. Mechanical tapping saddles for water works purposes and designed for use with PVC/PE pipe as per IS 4985/IS 4984 respectively. These saddles should be contoured to fit around the pipe. PP saddles shall be Blue/Black moulded-in with Nickel plated Brass / SS 304 metal female threaded outlets. Seal shall be thermoplastic elastomer rubber suitable for drinking water and nut-bolt-washer with SS. The PP Clamp saddle fittings shall be moulded with SS 304/Nickel plated Brass female threaded outlet inserted to connect necessary fittings. Thread dimension shall conform to IS-554/ISO-7. Adequate thickness of PP shall be provided to hold brass insert in place and avoid leakage while pressure plications. Fasteners shall be threaded type, with SS. Fasteners of size 125mm and above. The grade of raw material used must be certified by WRAS, UK for type test as per BS 6920 from their certified laboratories like NSF International Ltd. UK and certificate of Compliance to be produced for the following parameters: i) Odiur & Flavour of water ii) Appearance of water iii) Growth of Micro Organism iv) Extraction of Substances that may be of concern to public health (Cyto toxicity) v) Extraction of Metals Cost and Supply of Flow Control Valve 20mm 5-10Lpm Supply and Fixing of compression fittings shall comply with ISO 17885 2015, PN-16 rating and manufactured from virgin resin of PE-80 having blue color. Raw material must be WRAS approved as per BS 6920 for effect on water quality intended for human consumption. Compression fittings should have moulded in SS 304 threaded insert outlet with thread dimension confirming to IS 554/ISO 7. The cost shall include testing of all materials, labor all taxes (central and state), inspection charges, transportation up to site, transit insurance, loading, unloading, stacking and fixing etc, complete as specified and directed by the departmental Engineer in charge. b)Compression male/female threaded Elbow with SS insert D20mmx1/2 inch a) Cost of 20mm dia OD HDPE pipe 16kg/cm2 b) Laying and jointing 20mm dia HDPE pipes including trench excavation upto 0.5mts depth including testing refilling etc complete S/F 15 mm Nominal bore GI Pipe medium grade properties as per IS 1239 ISI mark with GI fittings including cost of pipe & its fittings, labour charges etc., complete S&F of 12.7mm brass bib cock(longer body) Indian make heavy duty excluding GST on 90 mm Dia pipe line