Panchayat Raj Engineering Department Tender

Fabrication ,transportation and and supply of wall mounted control panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using L&T / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets. Voltmeter ; 0-500 V 96x96mm size. Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab - 1No 0 to 20 Amps / 0 50 Amps Ammeter (96x96mm size). Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab- 1No Single phase preventor of suitable range Makes: L&T / Minilec / Powertec. - 1No. 32 A TP, 10KA MCB. Makes: Legrand / Schneider / - 1No Indication lamps (R-Y-B) with switch control - 1set Voltmeter & Ammeter selector switch - 2 Nos Supply and fixing of ISI Mark suitable capacitor Makes: L&T / Siemens / Schneider / Epcos/Havells From 10.00 HP with Automatic Star Delta Starter of Make C&S/Crompton / L&T / Siemens/BCH.

Cost, Supply and Fixing of 100 mm dia P.N. 1.60 Heavy duty double flanged ductile iron Non Return Valve including cost and conveyence of all materials and all labour charges etc., complete

Supply and Run of 6.00 Sqmm WPTC (Weather Proof Twin Core) ISI Alluminium wire including cost and conveyence of all materials and all labour charges etc., complete

Installation and commissioning of 10.00 HP SP Set with all its accessories including transportation of chain block and other necessary equipment and all labour charges etc., complete for finished item of work

Construction of pipe line for water supply with as per IS:4984/2016, with its amendments and revisions these on including supply of pipes, specials as per requirements, lowering laying and jointing of pipe line with cement solvent true to alignment and gradient, trench excavation for pipe lines in all soils except rock requring blasting, and refilling trenches with excavated earth (other than rocky & and boulders) soils with watering and ramming and removing surplus earth from the pipe line and filling pipe line with required water pressure and testing etc., complete. The rates are including the cost of pipes and cost of specials at 1.20% and excluding taxes and including cost and conveyance of all materials and labour charges etc., complete For 160 mm dia PE 100 grade 6Kg/Cm2 HDPE pipes with trench excavation of size 0.80x1.10 mts including laying and jointing charges

Cost, Supply, delivery and Fixing "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG- 400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN- 3202F4/BS:5163 Type A Flange drilling as per IS - 1538 excluding all taxes, duties and transportation including DI Flanged sockets, jointing meterials such as bolts nuts and rubber washers including meterials cost for main line labour charges for Flanged Joints and Lowering of valves, etc., completed. 150mm dia DI Sluice Valves P.N.1.60 on 160 mm dia HDPE Pipe lines including RCC Valve Chamber as per approved Estimate

Supply delivery of Double Flanged Slant seat Swing Check Valve (NRV) with body and Disc of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 with fully encapsulated in Vulcanized EPDM rubber & Fusion bonded Electro Static epoxy powder coating inside and outside color Blue RAL 5005 with Min. Coating thickness of 250 microns. The EPDM rubber & Epoxy rubber & Epoxy powder should conform to W 270 standards (Drinking water application) and face to face dimensions as per EN 558-1 / DIN 3202-F6 / IS 5312 & Flange connections as per IS:1538 excluding all duties, taxes and transportation 150 mm dia Non Return Valve including RCC Valve chamber as per approved Estimate

Cost, Supply, Delivery and fixing of (P.N.1.60) Tamper Proof DI Flanged Single Chamber Air Release Valves with body & cover made of Ductile Iron Grade GGG-40/SG-400/15 or GGG-50/SG- 500/7 or Equivalent as per IS1865, IS:3896- 2 with Food Grade Epoxy Powder Coating(EP-P) (Min:250 Micron) inside and Outside of Color Blue RAL 5005. All internal parts such as Float, shell, Cove Bolts etc. made of Austenitic alloy steel of SS AISI 304/316 and DN 50 float of and other components with ABS/PTFE/EPDM/NBR and generally conforming to DIN/BIS/AWWA standards (or) combination Flange drilling as per IS - 1538 and exclusive of all taxes and including Transportation, CI air tee of 150x150x50 mm dia, 2 Nos of HDPE tail pieces, 150 mm CI D/F Pipe 0.60 mts long 2 No.s, MTA, MS thereaded flanges, jointing meterials such as bolts nuts and, rubber washers including meterials cost for main line and air valves fixing, labour charges for fixing of CI Pipes and tees and fixing of vlaves, etc., completed. 50 mm dia DI Air Valve P.N.1.60 on 160mm dia HDPE Pipe line including RCC Valve Chamber

Earthwork excavation in all soils with initial lead and lift including cost and conveyence of all materials and all labour charges etc., complete 1st Mattu

Earthwork excavation in all soils with initial lead and lift including cost and conveyence of all materials and all labour charges etc., complete 2nd Mattu

Plain Cement Concrete (1:4:8) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 40mm size Hard Blasted Granite (IS383, 1970) metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for Foundation

Supply and filling of Local Sand including cost and convenyance of all material and all labour charges etc. complete as per standard specifications. Clause 305.3.9 MORD & 304 MORTH

M30 Grade Concrete using 20 mm HBG machine crushed Metal including cost and conveyence of alll materials and labour charges etc,,complete for Bottom Raft

M30 Grade Concrete using 20 mm HBG machine crushed Metal including cost and conveyence of alll materials and labour charges etc,,complete for Side Walls

M30 Grade Concrete using 20 mm HBG machine crushed Metal including cost and conveyence of alll materials and labour charges etc,,complete for Dome

M30 Grade Concrete using 20 mm HBG machine crushed Metal including cost and conveyence of alll materials and labour charges etc,,complete for Ring Beam

Accoproof Plastering with CM /(1:3) 12 mm thick including cost and conveyence of alll materials and labour charges etc,,complete

Cement Plastering with CM /(1:3) 12 mm thick including cost and conveyence of alll materials and labour charges etc,,complete

Snowcem Painting including cost and conveyence of alll materials and labour charges etc,,complete

Providing High Yield Strength Deformed (HYSD) steel bars (Fe 415 grade as per IS 1786-1985) of 8mm to 40mm diameters, cutting, bending, to required sizes and shapes placing in position with cover blocks of approved size and binding wire of 20SWG, forming grills for reinforcement work as per approved designs and drawings including cost and conveyance of bars from approved sources to site of work, including cost and conveyance of binding wire, cover blocks, chairs, overlaps, spacers, dowels, wastage etc., and all operational, incidental, and labour charges such as cutting, bending, placing in position, tying etc., and sales & other taxes,on cost of all materials complete for finished item of work.

Supply of Manhole Covers including cost and conveyence of alll materials and labour charges etc,,complete

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification 305 MORD / 304 MORTH

Supply and filling of Local Sand including cost and convenyance of all material and all labour charges etc. complete as per standard specifications. Clause 305.3.9 MORD & 304 MORTH

Plain Cement Concrete (1:4:8) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 40mm size Hard Blasted Granite (IS383, 1970) metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete

VRCC(1:1.5:3) using 20 mm HBG machine crushed metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Columns footing

VRCC(1:1.5:3) using 20 mm HBG machine crushed metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Columns

VRCC(1:1.5:3) using 20 mm HBG machine crushed metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Beams

Brick Msaonary with CM(1:6) using Second Class Bricks including cost and conveyance of all the materials etc complete

VRCC(1:1.5:3) using 20 mm HBG machine crushed metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Bed Blocks

VRCC(1:1.5:3) using 20 mm HBG machine crushed metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Lintle Beams

VRCC(1:1.5:3) using 20 mm HBG machine crushed metal for Sun Shades of Size 75 mm thick at one end 50mm other end and 600mm width ,including cost and conveyance of all the materials,but excluding the cost of the steel etc complete

VRCC(1:1.5:3) using 20 mm HBG machine crushed metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Roof Slab with100 mm Thick

Brick Msaonary with CM(1:6) using Second Class Bricks including cost and conveyance of all the materials etc complete

Flush Pointing with CM(1:3) including cost and conveyance of all the materials etc complete

Cement plastering with CM(1:5),12mm thick including cost and conveyance of all the materials ect complete.

Accoproof plastering with CM(1:5),12mm thick including cost and conveyance of all the materials ect complete.

Flooring with CC(1:4:8) using 40mm HBG machine crushed metal for 100mm thick and Top plastering with CM(1:3) ,20mm thick including cost and conveyance of all the materials ect complete.

Synthatic Enamel painting over primary coat and Enamel painting in two caots including csot and conveyance of all the materials ect complete for Doors and Windows

Painting With White Cement two coats including cost and conveyance of all the materials ect complete.

Snowcem painting including cost and conveyance of all the materials ect complete.

Providing High Yield Strength Deformed (HYSD) steel bars (Fe 415 grade as per IS 1786-1985) of 8mm to 40mm diameters, cutting, bending, to required sizes and shapes placing in position with cover blocks of approved size and binding wire of 20SWG, forming grills for reinforcement work as per approved designs and drawings including cost and conveyance of bars from approved sources to site of work, including cost and conveyance of binding wire, cover blocks, chairs, overlaps, spacers, dowels, wastage etc., and all operational, incidental, and labour charges such as cutting, bending, placing in position, tying etc., and sales & other taxes,on cost of all materials complete for finished item of work.

Construction of pipe line for water supply with as per IS:4984/2016, with its amendments and revisions these on including supply of pipes, specials as per requirements, lowering laying and jointing of pipe line with cement solvent true to alignment and gradient, trench excavation for pipe lines in all soils except rock requring blasting, and refilling trenches with excavated earth (other than rocky & and boulders) soils with watering and ramming and removing surplus earth from the pipe line and filling pipe line with required water pressure and testing etc., complete. The rates are including the cost of pipes and cost of specials at 1.20% and excluding taxes and including cost and conveyance of all materials and labour charges etc., complete For 90 mm dia PE 100 grade 6Kg/Cm2 HDPE pipes with trench excavation of size 0.70x1.00 mts including laying and jointing charges

Cost, Supply, delivery and Fixing "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG- 400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN- 3202F4/BS:5163 Type A Flange drilling as per IS - 1538 excluding all taxes, duties and transportation including DI Flanged sockets, jointing meterials such as bolts nuts and rubber washers including meterials cost for main line labour charges for Flanged Joints and Lowering of valves, etc., completed. 80mm dia DI Sluice Valves P.N.1.60 on 90 mm dia HDPE Pipe lines

Construction of Functional Hold Tap Connections (FHTCs) with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar for 65 to 180mm dia main with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80/PE100 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304/Nickel plated brass female threded outlet inserted to connection necessary fitting with threaded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm dia B class GI pipe as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16.0 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth), and 12.7mm dia Brass Bib cock long body Indian make heavy duty excluding GST and Seigniorge charges, including contractor' profit & overheads @ 13.615%.