Panchayat Raj Engineering Department Tender

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain (not exceeding 0.6 m depth) and foundation of other structures including breaking clods, ramming, spreading, sectioning, grading compacting with vibratory roller 80-100 KN to OMC compaction including to a top width of 7.5 m and raising to required height complete etc.as per requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 MoRD including contractors profit & Over head charges, but excluding GST and seigniorage etc., complete.

Construction of Shoulders by providing selected earth having minimum CBR of 10%, MDD not less than 1.85 g/cc with LL & PI not more than 40% and 20 respectively and spreading in uniform layers with tractor grader on prepared surface, and compacted at OMC with vibratory roller 80-100 kN to meet requirement of Table 300.2 with as per Technical Specification Clause 303 & 407 MoRD, by using machinery including contractors profit & Over head charges, but excluding GST and seigniorage etc., complete.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with Vibratory Roller 80-100 kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406 MoRD, including contractors profit & Over head charges, but excluding GST and seigniorage etc., complete

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 Kg/Sqm using mechanical means as per Technical Specification Clause 502 MoRD (for use on Wet mix macadam & WBM), including contractors profit & Over head charges, but excluding GST etc., complete for Prime Coat

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 Kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503 MoRD, including contractors profit & Over head charges, but excluding GST etc., complete for Tack Coat

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates (Table 500.13) either using penetration grade bitumen 60/70 grade at the rate of 14.6 Kg/10 Sqm to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a Hot Mix plant of 30-40 TPH, laying and rolling with a three wheel 0-100 KN static roller capacity, paver finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C including cost and conveyance of all materials from approved sources, labour charges and hire and operational charges of power road roller and all other machinery, tools and plants, providing barricading for diversion of traffic, erecting red flags other incidental and operational charges etc., complete for finished item of work as per clause 506 MoRD' 2014 including contractors profit & Over head charges, but excluding GST and seigniorage etc., complete using HMP

Providing and laying bituminous premixed seal coat (Type C) comprising of stone chipping of grading as defined in table 500.16 of MoST with Crushed stone chips of 6.7 mm size 100% passing through 9.5 mm seive and retained on 2.36 mm sieve applied @ 0.09 cum per 10 sqm, chips to be premixed by mechanical means .with the bitumunous binder using 6.50 Kgs of bitumen VG 30 grade for 10 sqm and rolling with power roller including of required line, level, grade to serve as wearing course on previously prepared surface and finishing to required level and grades including cost and conveyance of all materials from approved sources and stacking at site to departmental gauge for premeasurements, labour charges and hire and operational charges of power road roller 8 to 10 tonnes capacity and all other machinery, tools and plants, providing barricading for diversion of traffic, erecting red flags other incidental and operational charges etc., complete for finished item of work as per technical specification clause 508 of MoRD' 2014 including contractors profit & Over head charges, but excluding GST and seigniorage etc., complete for seal coat.By Mechanical Means

Road Furniture

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 MoRD / 804 MoRTH including contractors profit & Over head charges, but excluding GST and seigniorage etc., complete for Ordinary Kilometre Stone (precast)

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 MoRD / 804 MoRTH including contractors profit & Over head charges, but excluding GST and seigniorage etc., complete for 200 m Stone (precast)

Providing & fixing of typical PMGSY informatory sign board with LOGO as per MoRD secifications and drawing with Retiro Reflective sheeting including lettering and signs as applicable back ground with Apoxy paint. Three Alluminium Composite Material as per Drawings, top and middle plate duly welded with MS flat iron 25 mm x 5 mm size on black on edges. The lower plate will be welded with MS angle iron frame of lower most plate and flate iron frame of middle plate will be welded to 2 Nos. 75 mm x 75 mm of 12 SWG sheet tubes posts duly embedded in CC M15 grade blocks of 450 mm x 450 mm x 600 mm, 600 mm below ground level. The top most diamond plate will be welded to middle plate by 47 mm x 47 mm of 12 SWG sheet plate tube. All MS will be stove enmeled on both sides. Lettering and paining of superior quality in required shede and colour. All sections of framed posts and sheet tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1 if MoRD including contractors profit & Over head charges, but excluding GST and seigniorage etc., complete

Providing and fixing of Maintenance information board as per IRC:67 made of type Retro reflective sheeting vide Clause 1701.2.3 MoRD / 801.3 MoRTH fixed over Alluminium Composite Material of 4mm thickness and size of 900 x 1500 mm on a frame made up of 25 X 25 X 6 mm thick MS angles and 25 x 5 mm MS Flats and welded to welded MS flat Iron plates 50 x 5 mm size on back and welded to 75 mm x 75 mm x6mm MS hallow squar tube frame of height 3.00 m as per the drawing and painted with ready mixed synthetic enamel paint of superior quality in required shade and colour, lettering, colour,band, diagrams, specifications etc., complete as per MoRD specifications.The 75 mm dia steel tubes welded with 50 x 50 x 6 mm angle iron hold fasts of 225 mm long at bottom and painted with primer and two coats of epoxy paint and embedded in to cement concrete M15 grade of size 600 x 600 x 750 mm, 600 mm below ground level as per MoRD specifications clause 1701 including over head charges & contractors profit but excluding GST & Seigniorage charges etc., complete.

Providing and fixing of Citizen information board as per MoRD specifications and drawings with Retiro Reflective sheeting including lettering and signs as applicable back ground with Apoxy paint. The board will be a composite unit consisting of 2 MS plates of 1.6 mm (16 SWG) thickness and size of 900 x 750 mm welded over welded MS Flat iron plates 50 x 5 mm size on back and welded to 75 mm 3.65 mm thick (B class) steel tube frame of height 3.05 m as per the drawing and painted colour, lettering, colour, band, diagrams, specifications. the 75 mm dia steel tubes welded with 50 x 50 x 6 mm angle iron hold fasts of 225 mm long at bottom and painted with primer and two coats of epoxy paint and embedded in to cement concrete M15 grade of size 600 x 600 x 750 mm, 600 mm below ground level as per MoRD specifications clause 1701 including over head charges & contractors profit, etc., complete

Providing & fixing of typical PMGSY informatory sign board with LOGO as per MoRD secifications and drawing with Retiro Reflective sheeting including lettering and signs as applicable back ground with Apoxy paint. Three Alluminium Composite Material, top and Bottom plate duly Revited with MS flat iron 25 mm x 5 mm size on black on edges. The lower plate will be welded with MS angle iron frame of lower most plate and flate iron frame of middle plate will be welded to 1 No. 75 mm x 75 mm of 12 SWG sheet tubes posts duly embedded in CC M15 grade blocks of 450 mm x 450 mm x 600 mm, 600 mm below ground level. The top most diamond plate and Bottom Plate will be made with 25 mm X 25 mm X 5 mm MS Angles and welded MS tube tube. All MS painted Epoxy on Both sides. Lettering and paining of superior quality in required shede and colour. All sections of framed posts and sheet tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1 if MoRD including contractors profit & Over head charges, but excluding GST and seigniorage etc., complete at Every 2 Km

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3 MoRD fixed over aluminium sheeting 1.50 mm thick supported on a mild steel iron post 75 mm x75 mm x6 mm firmly fixed to the ground by means of properly designed foundation with M15 cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and technical specification clause 1701 MoRD including cost and conveyance of all materials, all labour charges, over head charges & Contractors Profit but excluding GST and seigniorage charges etc., complete for finished item of work at Speed breakers near Junctions,T Boards at junctions ,Prohibited boards at junctions (triangle of size 600 X 600 mm size)

Providing and erecting direction and place identification retro-refectorised sign as per IRC:67 made of encapsulated lens type refective type sheeting vide clause 1701.2.3 MoRD fixed over aluiminium sheeting, 2 mm thick with area not exceeding 0.90 sqm supported on mild steel iron posts 75 x 75 x 6 mm firmly fixed to ground by means of propoerly designed foundation with M15 grade cement concrete 450 x 450 x 600 mm, 600 mm below groubd level as per drawings and technical specification clause 1701 MoRD including cost and conveyance of all materials, all labour charges, over head charges & Contractors Profit but excluding GST and seigniorage charges etc., complete for finished item of work at Junctions.

Pavement markings with hot line applied Thermo plastic compound 2.50 mm thick including reflecting glass beads at 250 gms/sqm, thickness of 2.5 mm is exclusive of surface applied glass beads for providing centerline marking 300 cms length and 10 cm width with a gap of 450 cms including cost and convenyace of all materials equipment machinary and labour with all leads and lifts loading and unloading charges necessary for sucessful completion of work as directed by the Engineer-in-Charge and confirming to IS 164 - 1981 (1st revison reaffirmed in 1986) and clause 803 of MoST specification for roads and bridge works and also confirming to IRC 35 -1997 including cost and conveyance of all materials, all labour charges, over head charges & Contractors Profit but excluding GST and seigniorage charges etc., complete for finished item of work.

Cost & supply of Guard Stones ( 1200 x 200 x 200 mm) including overheads & contractor's profit but excluding GST