Panchayat Raj Engineering Department Tender

M 30 Grade Concrete using 20mm HBG Metal including cost and conveyance of all materials and labour charges including curing etc., complete upto Plinth level with concrete mixer For Bottom Raft

M 30 Grade Concrete using 20mm HBG Metal including cost and conveyance of all materials and labour charges including curing etc., complete upto Plinth level with concrete mixer For Side Walls 50 KL SUMP

M 30 Grade Concrete using 20mm HBG Metal including cost and conveyance of all materials and labour charges including curing etc., complete upto Plinth level with concrete mixer For Top Slab 50 KL SUMP

Plastering with C.M. (1:3) 12mm thick using 2 % of Acco proof powder including cost and conveyance of all materials, curing and all labour charges etc., complete., 50 KL SUMP

Plastering with C.M. (1:3) 12mm thick including cost and conveyance of all materials. scaffolding charges, curing and all labour charges etc., complete. 50 KL SUMP

Painting with snowcem or other equal approved water proof cement paint two coats over priming coat including cost and conveyance of all materials and all labour charges etc., complete., 50 KL SUMP

Supplying, fitting and placing HYSD bar reinforcement complete as per drawings and technical specifications for bars below 36mm dia including over laps and wastage etc., complete., 50 KL SUMP

Supply and Fixing of Redimade Manhole Cover including cost and conveyance of all materialscharges, and all labour charges etc., complete. 50 KL SUMP

Earth work excavation in all kinds of soils including boulders upto 0.30m dia for foundation of structures as per drawings and technical specifications clause 305.1 including setting out, construction of shoring and bracing removal of stumps and other deleterious materials and disposal upto lead of 50mts, dressing of sides and bottom and back filling in trenches with excavated suitable material including seigniorage charges as per technical specifications 305 MORD/304 MORTH with manual 1st Mattu 30 KL SUMP

Cement Concrete (1:4:8) using 40mm HBG Metal including cost and conveyance of all materials and labour charges including curing etc., complete upto Plinth level with concrete mixer (IC 2-5) 30 KL SUMP

Sand for filling in foundation treches/basement as per drawing and technical specification clause 305.3.9 MORD & 304 MORTH including cost and conveyance of all materials and labour charges etc., complete. 30 KL SUMP

M 30 Grade Concrete using 20mm HBG Metal including cost and conveyance of all materials and labour charges including curing etc., complete upto Plinth level with concrete mixer For Bottom Raft 30 KL SUMP

M 30 Grade Concrete using 20mm HBG Metal including cost and conveyance of all materials and labour charges including curing etc., complete upto Plinth level with concrete mixer For Side Walls 30 KL SUMP

M 30 Grade Concrete using 20mm HBG Metal including cost and conveyance of all materials and labour charges including curing etc., complete upto Plinth level with concrete mixer For Top Slab 30 KL SUMP

Plastering with C.M. (1:3) 12mm thick using 2 % of Acco proof powder including cost and conveyance of all materials, curing and all labour charges etc., complete., 30 KL SUMP

Plastering with C.M. (1:3) 12mm thick including cost and conveyance of all materials. scaffolding charges, curing and all labour charges etc., complete. 30 KL SUMP

Painting with snowcem or other equal approved water proof cement paint two coats over priming coat including cost and conveyance of all materials and all labour charges etc., complete., 30 KL SUMP

Supplying, fitting and placing HYSD bar reinforcement complete as per drawings and technical specifications for bars below 36mm dia including over laps and wastage etc., complete., 30 KL SUMP

Supply and Fixing of Redimade Manhole Cover including cost and conveyance of all materialscharges, and all labour charges etc., complete. 30 KL SUMP

Supply and Transportation of 5 HP 5star rated Open Well submersible motor pumpset, confirming to IS 8034 and motor confirming to IS 9283 with water proof winding, Pump shall be suitable for various Fixing head and discharge with stainless steel shaft.Motor suitable for working on 415V ± 10% , Three Phase 50 Hz AC supplyexcluding all taxes etc complete. for 6" Bore well.Makes: Kirloskar / Crompton / Texmo / CRI / KSB/ Lubi/ PSG/ AryenVarsha

Fabrication ,transportationand and supply of wall mounted control panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using L&T / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets. Voltmeter ; 0-500 V, 0 to 20 Amps / 0 50 Amps Ammeter, Single phase preventor of suitable range, 32 A TP, 10KA MCB, Indication lamps (R-Y-B) with switch control - 1set, Voltmeter & Ammeter selector switch - 2 Nos, Supply and fixing of ISI Mark suitable capacitor Makes for 7.50 HP with Star- Delta Starter of Make C&S/Crompton / L&T / Siemens/BCH.excluding all taxes etc complete.

Supply and Fixing of 65 mm dia B'Class Nominal Bore GI pipe Medium Grade properties & weight as per IS 1239 with GI fittings such as elbows tees couplings, nipples, plugs including excavation for trenches and refilling the trenches complete except for GI bends union and GI connectors with checkout and socket Tata or Zenith make or equivalent

Supply & Fixing of 50mm dia GI Long Coupling including cost and conveyance of all materials and labour charges etc complete but excluding taxes.

Supply & Fixing of 2.50Sqmm 4.0. crore cable wir ISI Alluminium Wire. Makes: Gold Medal / Million / GM / Vimal / Finecab / Nakoda / Plaza/ Payal / Sudhakar/ Rajnigandha/ Airson/ Orbit/ollvin/Beljin

Supply & Fixing of 65mm dia MS Clamp Sets ( 2 Nos )including cost and conveyance of all materials and labour charges etc complete but excluding taxes.

Supply & Fixing of 65mm dia CI Non Return Valve including cost and conveyance of all materials and labour charges etc complete but excluding taxes.

Supply & Fixing of 180mm dia MS Bore Cover including cost and conveyance of all materials and labour charges etc complete but excluding taxes.

Installation and commissioning of 5.0 HP submerssible pumpset with all its accessories including transportation of chain block and other necessary equipement and all labour charges etc. complete

Construction of pipe line for water supply with HDPE 110 mm dia 6kg/cm2 Pipes, PE 100 including earth work excavtion for pipe line trench of size 0.70 X 1.00 M using 2/3 quantity with Machinary and 1/3 quantity with manual in all soils except Rock requiring blasting, lowering, laying and jointing of pipe lines true to alignment and gradient and refilling trenches with excavated earth (other than rocky soil and boulders) with watering, tamping and removeing surplus earth from site of work and filling pipe line with water and testing etc., complete

Supply & Fixing of 110mm dia HDPE 6kg/cm2 Pipes, PE 100 grade including cost and conveyance of all materials and labour charges etc complete

Construction of pipe line for water supply with HDPE 90 mm dia 6kg/cm2 Pipes, PE 100 including earth work excavtion for pipe line trench of size 0.70 X 1.00 M using 2/3 quantity with Machinary and 1/3 quantity with manual in all soils except Rock requiring blasting, lowering, laying and jointing of pipe lines true to alignment and gradient and refilling trenches with excavated earth (other than rocky soil and boulders) with watering, tamping and removeing surplus earth from site of work and filling pipe line with water and testing etc., complete

Supply & Fixing of 90mm dia HDPE 6kg/cm2 Pipes, PE 100 grade including cost and conveyance of all materials and labour charges etc complete

Construction of pipe line for water supply with HDPE 75 mm dia 6kg/cm2 Pipes, PE 100 including earth work excavtion for pipe line trench of size 0.70 X 1.00 M using 2/3 quantity with Machinary and 1/3 quantity with manual in all soils except Rock requiring blasting, lowering, laying and jointing of pipe lines true to alignment and gradient and refilling trenches with excavated earth (other than rocky soil and boulders) with watering, tamping and removeing surplus earth from site of work and filling pipe line with water and testing etc., complete

Supply & Fixing of 75mm dia HDPE 6kg/cm2 Pipes, PE 100 grade including cost and conveyance of all materials and labour charges etc complete

Construction of pipe line for water supply with HDPE 63 mm dia 6kg/cm2 Pipes, PE 100 including earth work excavtion for pipe line trench of size 0.70 X 1.00 M using 2/3 quantity with Machinary and 1/3 quantity with manual in all soils except Rock requiring blasting, lowering, laying and jointing of pipe lines true to alignment and gradient and refilling trenches with excavated earth (other than rocky soil and boulders) with watering, tamping and removeing surplus earth from site of work and filling pipe line with water and testing etc., complete

Supply & Fixing of 63mm dia HDPE 6kg/cm2 Pipes, PE 100 grade including cost and conveyance of all materials and labour charges etc complete

Supply and delivery of 800mm dia "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS - 1538 excluding all taxes, duties and transportation.

Supply & Fixing of House Service connection (PP Saddle) PP clamp saddles PP clamp saddles shall be manufactured by injection moulding using virgin polypropylene. Mechanical tapping saddles for water works purposed and designed for use with PVC(PE pipe as per IS 4985/ IS 4984 respectively. These saddles should be contoured to fit around the pipe. PP saddles shall be Blue/Black moulded in with Nickel plated brass / SS 304 metal female threaded outlets. Seal shall be thermoplastic washer with SS. The PP clamp saddle fittings shall be moulded with SS. The Pp clamp saddle fittings shall be moulded with SS 304/ Nickel plated Brass female threaded outlet inserted to connect necessary fittings. Thread dimension shall conform to IS 554/ISO-7. Adequate thickness of PP shall be provided to Hold bras insert in place and avoid leakage while pressure applications. Fasteners shall be threaded type, with SS fasteners of size 125mm and above. The grade of raw material used must be certified by WRAS, UK for type test as per BS 6920 form their certified laboratories like NSF International Ltd., UK and certificate of compliance to be produced for the following parameters i) Odour & Flavour of water ii) Appearance of water iii) Growth of Micro Organism iv) Extraction of Substances that may be of concern to public health (Cyto Toxicity) v) Extraction of Metals excluding all taxes (as per SoR 2022-23) with Cost and supply of tamper proof house hold Non return cum flow control valve (with all three parts made by using sold steel bars of SS 316) with CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle (as per CPHEO manual) including cost of materials, manufacturing, loading, unloading, stocking, transit insurance, transpiration but excluding GST with Compression male / female threaded adaptor with SS insert D20mm X ½” with Compression male / female threaded adaptor with SS insert D20mm X ½” with Manufacture, supply & delivery of HDPE pipe confirming to IS 4984-2016 of PE-100 grade material along with all fittings, including cost of materials, manufacturing, loading, unloading, stacking, transit insurance, transportation excluding all taxes with 20mm OD HDPE pipe 16.0 Kg/Sqcm with Laying, Jointing of 20mm dia HDPE pipes as per BIS No.7634 Part-II/75 including treanch excavation upto 0.50mts depth including testing, refilling etc., complete with Cost, supply & fixing of 15mm Nominal Bore GI pipe Medium Grade properties & Weight as per IS 12391 ISI mark with GI Fittings including the cost of pipe & its fittings, labour charges etc., complete excluding GST with S&F of 12.7mm brass bib cock (long body) Indian make heavy duty excluding GST and including Contract Profit 13.615% For 63 mm X 1/2" with Support FHTCs

Supply & Fixing of House Service connection (PP Saddle) PP clamp saddles PP clamp saddles shall be manufactured by injection moulding using virgin polypropylene. Mechanical tapping saddles for water works purposed and designed for use with PVC(PE pipe as per IS 4985/ IS 4984 respectively. These saddles should be contoured to fit around the pipe. PP saddles shall be Blue/Black moulded in with Nickel plated brass / SS 304 metal female threaded outlets. Seal shall be thermoplastic washer with SS. The PP clamp saddle fittings shall be moulded with SS. The Pp clamp saddle fittings shall be moulded with SS 304/ Nickel plated Brass female threaded outlet inserted to connect necessary fittings. Thread dimension shall conform to IS 554/ISO-7. Adequate thickness of PP shall be provided to Hold bras insert in place and avoid leakage while pressure applications. Fasteners shall be threaded type, with SS fasteners of size 125mm and above. The grade of raw material used must be certified by WRAS, UK for type test as per BS 6920 form their certified laboratories like NSF International Ltd., UK and certificate of compliance to be produced for the following parameters i) Odour & Flavour of water ii) Appearance of water iii) Growth of Micro Organism iv) Extraction of Substances that may be of concern to public health (Cyto Toxicity) v) Extraction of Metals excluding all taxes (as per SoR 2022-23) with Cost and supply of tamper proof house hold Non return cum flow control valve (with all three parts made by using sold steel bars of SS 316) with CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle (as per CPHEO manual) including cost of materials, manufacturing, loading, unloading, stocking, transit insurance, transpiration but excluding GST with Compression male / female threaded adaptor with SS insert D20mm X ½” with Compression male / female threaded adaptor with SS insert D20mm X ½” with Manufacture, supply & delivery of HDPE pipe confirming to IS 4984-2016 of PE-100 grade material along with all fittings, including cost of materials, manufacturing, loading, unloading, stacking, transit insurance, transportation excluding all taxes with 20mm OD HDPE pipe 16.0 Kg/Sqcm with Laying, Jointing of 20mm dia HDPE pipes as per BIS No.7634 Part-II/75 including treanch excavation upto 0.50mts depth including testing, refilling etc., complete with Cost, supply & fixing of 15mm Nominal Bore GI pipe Medium Grade properties & Weight as per IS 12391 ISI mark with GI Fittings including the cost of pipe & its fittings, labour charges etc., complete excluding GST with S&F of 12.7mm brass bib cock (long body) Indian make heavy duty excluding GST and including Contract Profit 13.615% For 75 mm X 1/2" with Support FHTCs

Supply & Fixing of House Service connection (PP Saddle) PP clamp saddles PP clamp saddles shall be manufactured by injection moulding using virgin polypropylene. Mechanical tapping saddles for water works purposed and designed for use with PVC(PE pipe as per IS 4985/ IS 4984 respectively. These saddles should be contoured to fit around the pipe. PP saddles shall be Blue/Black moulded in with Nickel plated brass / SS 304 metal female threaded outlets. Seal shall be thermoplastic washer with SS. The PP clamp saddle fittings shall be moulded with SS. The Pp clamp saddle fittings shall be moulded with SS 304/ Nickel plated Brass female threaded outlet inserted to connect necessary fittings. Thread dimension shall conform to IS 554/ISO-7. Adequate thickness of PP shall be provided to Hold bras insert in place and avoid leakage while pressure applications. Fasteners shall be threaded type, with SS fasteners of size 125mm and above. The grade of raw material used must be certified by WRAS, UK for type test as per BS 6920 form their certified laboratories like NSF International Ltd., UK and certificate of compliance to be produced for the following parameters i) Odour & Flavour of water ii) Appearance of water iii) Growth of Micro Organism iv) Extraction of Substances that may be of concern to public health (Cyto Toxicity) v) Extraction of Metals excluding all taxes (as per SoR 2022-23) with Cost and supply of tamper proof house hold Non return cum flow control valve (with all three parts made by using sold steel bars of SS 316) with CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle (as per CPHEO manual) including cost of materials, manufacturing, loading, unloading, stocking, transit insurance, transpiration but excluding GST with Compression male / female threaded adaptor with SS insert D20mm X ½” with Compression male / female threaded adaptor with SS insert D20mm X ½” with Manufacture, supply & delivery of HDPE pipe confirming to IS 4984-2016 of PE-100 grade material along with all fittings, including cost of materials, manufacturing, loading, unloading, stacking, transit insurance, transportation excluding all taxes with 20mm OD HDPE pipe 16.0 Kg/Sqcm with Laying, Jointing of 20mm dia HDPE pipes as per BIS No.7634 Part-II/75 including treanch excavation upto 0.50mts depth including testing, refilling etc., complete with Cost, supply & fixing of 15mm Nominal Bore GI pipe Medium Grade properties & Weight as per IS 12391 ISI mark with GI Fittings including the cost of pipe & its fittings, labour charges etc., complete excluding GST with S&F of 12.7mm brass bib cock (long body) Indian make heavy duty excluding GST and including Contract Profit 13.615% For 90 mm X 1/2" with Support FHTCs