Panchayat Raj Engineering Department Tender

RWS;Cost and supply and fixing of 180mm dia PVC End Cap including CP @ 13.615%

RWS;Labour charges for Slotter cutting to 180 mm dia PVC 6 Kg/Cm2 including CP @ 13.615%

RWS;Towards conducting Geologist site investigation survey charges including hirign of vehicle from Nellore work spot and viceversa and labour charges etc complete including CP @ 13.615%

RWS;Supply and Transportation of 5.00 HP 5 Star rated Submersible motor pumpset, confirming to IS 8034 and motor confirming to IS 9283 with water proof winding,Pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 415V ± 10% , Three Phase 50 Hz AC supply,etc complete for 6" Bore well. - 5.00HP, 5-10Stage - ELEC-5.4.5 (b) Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/Aryen Varsha including CP % 13.615%

RWS;Fabrication ,transportationand and supply of wall mounted Control panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using L&T / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets - .ELEC-5.4.17 (b) Voltmeter ; 0-500 V 96x96mm size. Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab - 1No 0 to 20 Amps / 0 50 Amps Ammeter (96x96mm size). Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab- 1 No Single phase preventor of suitable range Makes: L&T / Minilec / Powertec. - 1No. 32 A TP, 10KA MCB. Makes: Legrand / Schneider / - 1No Indication lamps (R-Y-B) with switch control - 1set Voltmeter & Ammeter selector switch - 2 Nos Supply and fixing of ISI Mark suitable capacitor Makes: L&T / Siemens / Schneider / Epcos/Havells. Upto 7.5 HP with DOL Starter of. Make C&S.Crompton / L&T / Siemens/BCH.

RWS;Cost and supply of 7/16 Alluminium service wire of standard make including CP @ 13.615%

RWS;Cost and supply of PVC insulated and PVC sheathed, flexible 3 core flat type cable 4.00 Sqmm for submersible pumpsets,conductors composed of annealed high conductivity copper wire, confirming to IS 694 & its revisions and amendments from time to time delivery at site of installation of pumpsetincluding CP @ 13.615%

RWS;Supply of Galvanised Mild steel pipes (Medium class of 50 mm dia nominal bore) confirming to IS 1239 / Part I /1990 continuously welded ERW / HFIW type and screwed at both ends as per IS 554 one end with socket (Heavy class) as per IS 1239 / Part II / 1992 and other fitted with plastic ring and delivery in small quanities at work site of pump installation with replacement guarentee for a period of six months on installation for exact length of 3 metres + 5% including cost and conveyance, excise duty and sales tax etc., complete including CP @ 13.615%

RWS;Cost and supply of 50 mm dia GI heavy Coupling including CP @ 13.615%

RWS;Cost and supply of 50 mm dia GI Bend including CP @ 13.615%

RWS;Cost and supply of 50 mm dia CI Non return valve including transportation charges and CP @ 13.615%

RWS;Cost and supply of 50 mm dia MS Flangeset including CP @ 13.615%

RWS;Cost and supply of 50 mm dia MS Clampset including CP @ 13.615%

RWS;Cost and supply and fixing of 180mm dia PVC Bore Cover including CP @ 13.615%

RWS;Cost and supply and fixing of 75 mm dia PVC FTA including CP @ 13.615%

RWS;Coveyance charges of materials to work spot

RWS;Installation and erection charges of pumpset including erection, earthing, testing & commissioning, fixing panel board with its accessories, fixing GI pipes & specials, valves etc., complete including CP @ 13.615%

RWS;Providing 75 mm dia, 6Kg/Cm2 HDPE PE-100 grade pipes as per IS Specifications, with its latest amendments and revisions thereon, including supplying of pipes, necessary specials such as bends, Tees, etc., lowering, laying and jointing of pipe lines true to alignment and gradient, trench excavation of 0.70 x 1.00 mts . Earth work exvacation in all soils upto SDR using 2/3rd machinery and 1/3rd manual for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering, tamping and removing surplus earth from site of work and filling the pipeline with water and testing etc., complete as specified in Technical specifications (Part-B-Volume-I) and as per drawing (Part C-Volume-1). The rates are inclusive of cost and conveyance of all materials and labour charges for finished item of pipeline work , including Overheads and contractors profit @ 13.615% and excluding GST.

RWS;Cutting of open CC road surface with concrete saw cutter and removal with Breaker including CP @ 13.615%

RWS;CC road BCC M20 with 20 mm HBG metal including cost and conveyance of all materials and labour charges etc., complwete for relaying of CC cutting portion including CP @ 13.615%

RWS;Earth work excavation for foundation in as per drawing and technical specifications Clause 305.1 including setting ot, construction of shoring and bracing removal of stumps and other deleterious material and disposal up to a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per techincal specification 305 MOD / 304 MORTH

RWS;Plain Cement Concrete to (1:4:8) portion nominal mix (Cement fine aggregate: Coarse aggreagte) using 40 mm size HBG metal from approved quarry including cost and conveyance of all materials like Cement, Sand coarse aggregate, water etc., to site, including seignourage charges, sales and other taxes on all materials, all operational, incidental and labour charges such as mixing, laying, curing concrete etc., complete for finished item of work for Foundations and flooring for machine mixing

RWS;Brick masonry with cm (1:6) proportion using II nd class bricks traditional size 23x11x7 cm from approved source haing crushing strength not less than 35 kg / sqm including cost and conveyance of all materials like cement, sand bricks, water etc., to site including seignourage charges sales and other taxes on all materials and all operational, incidental andlabour charges such as mixing cement mortar, curing scafolding charges, counstructing masonary, lift charges curing etc complete for finished item of work for foundation and basement

RWS;Sand filling in foundation and basement for works including cost and conveyance of all materials and labour charges, seigourage charges, watering and tamping etc complete

RWS;Plastering with CM (1:5) 12mm thick including cost and conveyace of all materials like cement, sand, water etc to site, cost of seignourage charges and all other taxes on all materials and operational, incidental charges and all labour charges for mixing mortar, finishing, scafolding, lift charges, curing including cutting grooves etc., as directed by Engineer-In-Charge, complete

RWS;Supplying, fitting and placing HYSD bar reinforcement as per drawings and technical specifications, including overlaps and wastage, where they are not welded including cutting, bending, placing in postion tying grills including cost of binding wire etc., complete

RWS;RCC M-20 Nominal mix (Cement : fine aggregate: coarse aggregate) corresponding to Table 9 of IS 456 using 20 mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc to site and including seignourages charges, sales and other taxes on all materials including all operational and labour charges such as machine mixing, laying concrete, curing etc., complete including cost of steel and its fabrication charges for finished item of work, including centering, shutteing for Precast top slab including CP @ 13.615 %

RWS;Painting with Snowcem or other equal and approved water proof cement paint over primary coat (all colours)

RWS;Supply and fixing of MS welded grill gate of size 0.60x0.70 M including cost and conveyance of all materials, labour charges etc complete

RWS;Supply and fixing of House service connections (PP Saddle) PP Clam saddles - PP clamp Saddles shall be manufactured by injection moulding using virgin polypropylene. Mechanical tapping saddles for water works purposes and designed for use with PVC / PE pipe as per IS4985/IS 4984 respectively. These saddles should be contoured to fit around the pipe. PP saddles shall be Blue / Black moulded in with Nickle plated Brass / SS 304 metal female threaded outlets. Seal shall be thermo plasticelastomer rubber suitable for drinking water and nut-bolt-washer with SS. The PP Clampsaddle fittings shall be moulded with SS 304/Nickle plated Brass female threaded outlet inserted to connect necessary fittings. Thread dimension shall confirm to IS-554 / ISO-7. Adequate thickness of PP shall be provided to hold brass insert in place and avoid leakage while pressure aaplications. Fasteners shall be threaded type, with SS. Fasteners of sie 125 mm and above. The arade of raw material used must be certified by WRAS, UK for typetest as per BS 6920 from their certified laboratories like NSF International Ltd. UK and certificate of compliance to be produced for the follwoing parameters: i) Odour & Flavour of water, ii) Appearance of water, iii) Growth of Micro Organism, iv) Extaction of substances that may be of concern to public health (Cyto toxicity), v) Extraction of metals (as per SoR 22-23) excluding GST including CP @ 13.615%

RWS;Cost and supply of tamer proof house hold Non return cum Flow control valve (with all three parts made by using solid steel bars of SS 319) with CNC machine make and of 15 mm dia designed for 5 LPM discharge @ 0.5 bar pressure loss, not excedding the flow of 7 LPM at 1 bar pressure and working on float principle (as per CPHEO manual) including cost of materials, manufacturing, loading, unloadin, stacking, transit insurance, transportation but excluding GST.including CP @ 13.615%

RWS;Cost, Supply and fixing of compression fittings shall comply with ISO 17885 2015, PN-16 rating and manufacture from virgin resin of PE-80 having blue colour. Raw material must be WRAS approved as per BS 6920 for effect on water quality intended for human consumption. Compression fittings should have moulded in SS 304 threaeded insert outlet with thread dimension conforming to IS 554/IS07. The cost shall include testing of all materials, labour all taxes (central and state) inspection charges, transportation up to site, transit insurance, loading, uploading, stacking and fixing etc complete as specified and directed by the department engineer incharge excluding GST Compression male / female threaded adaptor with SS insert D20 mmx 1/2" including CP @ 13.615%

RWS;Compresson male / female threaded elbow with SS insert D20 mm x 1/2"

RWS;Manufacture, Supply and delivery of 20 mm dia OD 16 Kg/Cm2 HDPE pipe confirming to IS 4984 - 2016 of PE-100 grade material along with all fittings, including cost of materials, manufacturing, loading, unloading, stacking, transit insurance, transportation but excluding GST including CP @ 13.615%

RWS;Laying, Jointing of 20 mm dia HDPE pipes including trench excavation up to 0.5 mts depth including testing, refilling etc., complete including CP @ 13.615%

RWS;Cost and supply of 15 mm dia GI Pipe Medium Grade properties and weight as per IS 12391 ISI mark with GI Gittings including the cost of pipe and its fittings, labour charges etc complete excluding GST including CP @ 13.615%

RWS;Supply and fixing of 12.7 mm brass bib cock (long body) Indian make heavy duty excluding GST including CP @ 13.615%

RWS;Add Contractor Profit @ 13.615%