Municipality Tender

RCC M- 20 Design mix (Cement 380 kgs fine aggregate: coarse aggregate) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work, but excluding centering, shuttering. (Page No.664) BLD CSTN-2-13 & 14 S.No.21- a) Column Footings

For Columns

c) Top beam

Masonry work in CM (1:6) prop with Flyash Cement solid blocks of size 290 x 225 x 140 mm for manufacturing of flyash solid blocks using flyash of 80 kgs, cement of 15 kgs, Gypsum of 5 kgs and stone dust including cost and conveyance of all materials, labour charges, scaffolding and curing etc., complete with a compressive strength not less than 50 kg/sqm for walls for Superstructure walls.

Plastering 12 mm thick in CM(1:4) including cost and conveyance of all materials like cement, sand, water etc., to site and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, scaffolding, lift charges, curing, including cutting grooves as directed by Engineer-in-charge etc., and overheads & contractors profit complete for finished item of work . but excluding seigniorage charges

Supplying, fitting and placing HYSD bar reinforcement in foundation complete as per drawings and technical specifications for Bars below 36 mm dia including over laps and wastage, where they are not welded - BLD - CSTN - 2 / 19.

White washing two coats with whiting of approved quality to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost of all materials, labour charges and incidental such as scaffolding, lift charges etc., complete for finished item of work, but excluding conveyance charges of materials

Supply and Fabrication of framed Structurel ike window grills,Compound wall Grills,Iron Dors,Windows,Gates,Frames for Chain link mesh,Roof Trusses by using tubes & pipes GI Hollow Section as per standard including cost of welding rods,power charges,labour charges for cutting,placing,welding and erecting in position and fixing,cost & Conveyance of all materials including wastage to site with all taxes and duties etc complete for finished item of work.

Painting with Synthetic Enamel paints Two Coats For New Iron Work of approved brand after thoroughly brushing surface to remove dirt including cost and conveyance of materials to work and all oprational, incidental,labour charges for finished item of work as per SS and as directed by the departmental officer incharge of the work.

Providing Name board (7.00 x 0.75 )with MS Angulars and MS Sheet including Two Coats of Enamel paint over Primary Coat and Lettering with Enamel Paint including Scaffolding Charges all labour charges cost of paint etc,,Complete as directed by the department

Construction of un-reinforced, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates, maximum in a concrete mixer of not less than 0.2 cum capacity and appropeiate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 mictron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with sholvels, rakes, compacted using needle and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, Sealent, Primer, near approaches to bridge / culvert and construction joints, admixtures as approved, curing for 14- days, curing compound and water finishing to lines and grade as per drawing and Technical Specification Clause 1501 MORD. RBR-CCPV-5