Municipal Corporation Tender

Conveyance of excavated earth with an average lead of 2 KM including loading, unloading etc; complete as per SS and also as per the directions of departmental authorities. Add extra for leads and lifts.

Supply and Delivery of Quarry Dust from approved quarry including cost and conveyance of all materials labour charges, spreading, sectioning, ramming, watering etc complete as per SS.

Providing laying spreading and compacting graded HBG crushed stone aggregate to Wet Mix Mecadam specification as per table 400-13 including cost of all materials and including premixing the material with water at OMC in Mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in base courses on well prepared surface and compacting with vibratory roller to acheive the desired density etc. as directed by the Engineer-in-Charge and as per MORT & H specification 406 for finished item of work

Providing concrete for plain concrete (M20 Design mix) using 343 Kgs Cement 20 mm,10mm nominal size Graded hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of MORTH

Brick work in CM (1:6) using 2nd class bricks from local kilns including cost and conveyance of all materials, labour charges, seignorage etc., complete as per SS. (with extra leads and lifts)

Plastering with CM (1:4) 12mm thick including cost and conveyance of all materials, seigniorage charges and labour charges for mixing of mortor watering curing etc. complete.With extra leads and lifts.

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS : 383, maximum in a concrete mixer of not less than 0.2 cum capacity and appropeiate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 mictron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with sholvels, rakes, compacted using needle, scareed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days, curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501 MORD. Unit = cum. including cost and conveyance of all materials and labour charges etc,Complete

Separation Membrane of impermeable plastic sheeting 125 micron thick (M-164 common SSR)

Supply of bituminous hot sealing compound (grade-A ISI ) poly sulphide and sealing the joints incl.cost and conveyance of all materials etc.but excl.labour charges for placing in position for contraction joints at 1.50 interval / for expansion joints/for longitudinal joints as per MORTH specification number 602-1 Rm

Supply of 25mm thick high performance expansion joint filler board (SILFLEXCAPCELLHD-100 or equivalent make),placing the same 25mm below top of pavement slab sealing with bituminous hot sealing compound (Grade-A-ISI) polysulphudiet 50mm interval in CC.Pavement incl.cost and conveyance of all materials but excl.labour charges for placing in position,for expansion joints confirmig to MORTH Specification 602-1Rmt of joint length

Providing RCC M20 Design Mix using 20mm, 10mm size HG metal chips for approved quarry including cost and conveyance and 400 Kgs. cement per Cum. of concrete for estimate purpose of all materials and labour charges for mixing, laying, tamping, form work, watering, curring etc., complete excluding cost of steel as per SS and authorities. (Rate will be paid based on the design mix if cement quantity is reduced)

Providing High Yield Strength Deformed ( HYSD) / Thermo Mechanically Treated (TMT) / Mild Steel (MS) Steel bars of SAIL / VSP / TATA (Fe 415 grade as per IS 1786-1979) of different diameters for RCC works including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including all materials etc., complete for finished item of work as per SS.

Manufacturing, Supply, Delivery and fixing of M.S. Iron Gate , MS Grill using with M.S. Angulars, M.S. flats including cost and conveyance of all materials and labour charges for cutting, welding, grinding and fixing etc., , complete.as directed by the departmental authorities.