Municipal Corporation Tender

Conveyance charges for Machinery loading and unloading up to 2 Km including all materials etc.,complete as directed by the departmental authorities.

Brick work CM (1:6) using 2nd class bricks including cost and convayence of all materials and labour chargs mixing laying tamping watering etc complete

Plastering CM(1:4) 12mm thick including cost and cpnvayence of all materials and labour chargs mixing laying tamping watering etc complete

Collection and Supply of Dust for filling including Cost and coneyance charges, Spreading, Sectioning etc., complete.

Providing concrete for plain concrete (M10) using 220 Kgs Cement ,40 mm nominal size hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of MORTH

RCC vertical walls of plane surface (rate is for both sides centering) including open drains of 600mm size and above.

Providing concrete for plain concrete (M20 Design mix) using 343 Kgs Cement 20 mm,10mm nominal size Graded hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of MORTH

Supply and placing of the RCC M20 (Design Mix) concrete corresponding to IS 456 using weigh batcher / mixer 20mm,10mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry, Cement 347 Kgs including cost and conveyance of all materials like cement, fine aggrregate (sand) coarse aggregate, water etc., to site and all labour charges such as machine mixing, laying concrete, curing etc., complete but excluding cost of steel and its fabrication charges for finished item of work. (Without form work)

Supply and placing of the RCC M20 (Design Mix) concrete corresponding to IS 456 using weigh batcher / mixer 20mm,10mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry, Cement 347 Kgs including cost and conveyance of all materials like cement, fine aggrregate (sand) coarse aggregate, water etc., to site and all labour charges such as machine mixing, laying concrete, curing etc., complete but excluding cost of steel and its fabrication charges for finished item of work. (With form work)

Supplying, fitting and placing HYSD bar reinforcement as per drqwings and technical specifications clauses 1000 and 1202 MORD & 1100, 1600 MORTH for bars below 36mm dia including over laps and wastage, where they are not welded including cost and conveyance of binding wire and preparation and tying grills and fixing in position and labour charges etc., complete

Separation Membrane of impermeable plastic sheeting 125 micron thick

Manufacture as per BIS:12592 (Part 1&2) Supply & Delivery of manhole covers and frames with ISI marking anywhere in A.P., F.O.R. destination including, loading, un-loading & stacking at site but excluding all taxes.EHD-35 with 560mm dia clear opening.

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS : 383, maximum in a concrete mixer of not less than 0.2 cum capacity and appropeiate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 mictron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with sholvels, rakes, compacted using needle, scareed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days, curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501 MORD. Unit = cum. including cost and conveyance of all materials and labour charges etc,Complete.

Supply of 25mm thick high performance expansion joint filler board (SILFLEXCAPCELLHD-100 or equivalent make),placing the same 25mm below top of pavement slab sealing with bituminous hot sealing compound (Grade-A-ISI) polysulphudiet 50mm interval in CC.Pavement incl.cost and conveyance of all materials but excl.labour charges for placing in position,for expansion joints confirmig to MORTH Specification 602-1Rmt of joint length

Supply of bituminous hot sealing compound (grade-A ISI ) poly sulphide and sealing the joints incl.cost and conveyance of all materials etc.but excl.labour charges for placing in position for contraction joints at 1.50 interval / for expansion joints/for longitudinal joints as per MORTH specification number 602-1 Rm