Engineering Projects India Limited Tender

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submitt the design of loading platform for the approval of Engineer-in-charge. Single pile above50 tonne and upto 150 tonne Safe capacity

Lateral load testing of single pile in accordance with IS Code of practice IS : 2911 (Part IV) for determining safe allowable lateral load on pile :

600 mm dia piles

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submitt the design of loading platform for the approval of Engineer-in-charge. Single pile above50 tonne and upto 150 tonne Safe capacity

Above 50 tonne and upto 100 tonne capacity pile

Upto 50 tonne capacity pile

500 mm-(minimum 3 Numbers PVC pipes to be embedded)

500mmdia piles

Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean concrete lumps etc. and use of computerised equipment and high skill trained personal for conducting the test & submission of results, all complete as per direction of Engineer-in- charge.

500 mm & 600 MM dia

800 mm, 900 & 100 Dia

1000mm dia pile

Fabrication , Erection and Driving of 6mm / 8mm thick liner maximum upto 8.00m depth for any dia unsign rigs, cranes and including all tool and tackles. Liner material will be supplied by EPI

PILING WORK Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-40 (Minimum cement content -as per design mix ) of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note:(i)Truck Mounted rotary/TMR/Tube well boring machine shall not be used. (ii) Piles are to be founded with a socketting legth of 2D into the appropriate strata Note: Design Mix approval shall be obtained by EPI. However RMC supply scope is with bidder. Thesource of RMC is as follows: 1) Ultratech RMC atchuthapuram 2) Sravani RMC , Atchuthapuram , base rate for M-40 is Rs . 6400.00 3) trimme pile is under bidder scope 4) the wastage of concrete shall not be separately 5) Breakig first 1.2 m depth / depth specified by DGNP is under the scope of the bidder.

Routine test (Test Load 1.5 times the Safe capacity)

Routine test (Test Load 1.5 times the Safe capacity)

600 mm-(minimum 4 Numbers PVC pipes to be embedded)

Conducting standard penetration tests as per IS: 2131 through pipe in all types of soil during boring only for such piles as directed, all as specified at every one metre interval, 16 m onwards from existing ground level and recording accurately the penetration.

Initial test (Test Load 2.5 times the Safe capacity)

Steel Reinforcement for RCC work including straightening , cutting, bending and placing in position and binding all complete.

Initial test (Test Load 2.5 times the Safe capacity)

900mm dia pile

labour charge for Fabrication, cutting , pending laying , making the pile reinforcement gauge and erection reinforcement gauge inclduing cover block , tie bars, binding wire etc ( exluding cost of reinforcement Steel ) Unit of measurement in kgs

Conducting routine vertical load test for 1.5 times safe load carrying capacity by means of High Strain Dynamic Load Test including provision and erection of crane- hammer-drop mechanism, acceleration and displacement velocity transducers to record both force and velocity including excavation, dewatering, preparation of pile head including building up of pile, additional reinforcement if any etc. all complete as per approved method (ASTM D4945-89), submission of test report, specifications and instructions of the Engineer for piles of following diameter :