Endowments Department Tender

Dismantling, clearing away and carefully stacking useful materials for re use and disposal of unserviceable materials with 100m lead as directed by Executive Engineer duly taking actual premeasurements before dismantling including all labour charges , overheads & contractor profit etc., complete Kadapa slabs or shahabad stone slabs on sand bed

Dismantling, clearing away and carefully stacking useful materials for re use and disposal of unserviceable materials with 100m lead as directed by Executive Engineer duly taking actual premeasurements before dismantling including all labour charges , overheads & contractor profit etc., complete Old cement mortar plaster

Earth work excavation for foundations (Manual Means) of buildings, septic tank, sump, compound wall in ordinary soils and depositing on bank with an initial lead of 10m and 1m additional lift charges over the initial depth up to 3m including all operational,incidental, labour charges such as shoring, sheeting, planking, strutting etc., and overheads & contractors profit complete for finished item of work excluding seigniorage excluding dewatering charges etc., as per SS 20 B(APSS 308)

Plain Cement Concrete (1:4:8) (cement: fine aggregate: Coarse aggregate) for foundations and under flooring bed using coarse aggregate 40mm size hard , machine crushed granite from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, excluding seigniorage charges, sales & other taxes on all materials and including all charges for machine mixing, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc., and overheads & contractors profit complete for finished item of work. (APSS No. 402)

VRCC M-20 grade nominal mix (cement :fine aggreegate: coarse aggregate) corresponding to table 9 of IS456 using 20mm size machine crushed hard granite metal (coarse aggreegate)from approved Quarry including cost and conveyancej of all materials like cement,fine aggregate(sand)coarse aggregate, water etc, to site and excluding seigniorage charges,sales and other taxes on all materials including all operational incidental and labour charges such as machine mixing , laying concrete, curing etc., complete but excluding cost of steel and its fabrication charges for finished item of work.

Plastering 20mm thick in two coats using screened sand with base coat of 16mm thick in CM(1:6) and top coat of 4mm thick in CM(1:4) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site, excluding seigniorage charges, sales & other taxes on all materials, and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, scaffolding, lift charges, curing, including cutting grooves as directed by Engineer-in-charge etc., and overheads & contractors profit complete for finished item of work .(SS 901,903 & 904)

Flooring with ceramic tiles 7.30mm thick , 1st quality and of size as approved by Engineer-in-charge, set over base coat of cement mortar (1:8), 12mm thick using screened sand over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 Kgs per Sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand , water and tiles etc., and overheads & contractors profit complete for finished item of work. (APSS No.701 & 707)

Gronolithik Concrete Flooring 20 mm thick with (1:1:2), using 6mm to 12 mm size hard granite machine crushed metal laid over CC bed already laid or RCC roof slab, in alternate panels of size not exceeding 1.50 m x 1.50 m and finishing the top surface to required smoothness and slopes and thread lining including cost of all materials like cement, metal, sand and water etc., complete, excluding seigniorage charges, etc., complete for finished item of work, but excluding the cost of conveyance of all materials(83) in Ground Floor

Painting to new walls with 2 coats of acrylic emulsion paint weather proof water-based, modified acrylic with silicon additives exterior grade having VOC (Volatile Organic Compound ) content less than 50 grams/ liter. approved brand,of first grade over cement primary making 3 coats in all to give an even shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance of all materials to work site and operational, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work as per SS911 for internal walls.

Painting to new walls with 2 coats of acrylic emulsion paint weather proof water-based, modified acrylic with silicon additives exterior grade having VOC (Volatile Organic Compound ) content less than 50 grams/ liter. of approved brand and colour over a base coat of appropriate primer of approved brand,of first grade making 3 coats in all to give an even shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance of all materials to work site and operational, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work as per SS911 for External walls.

Painting two coats with synthetic enamel paint Grade-II VOC (Volatile Organic Compound) content less than 50 grams/litre over primer coat of red oxide to new iron work including cost and conveyance of all materials to site, sales & other taxes, incidental, operational and all labour charges etc.,and overheads & contractors profit complete for finished item of work in all floors. (SS No. 1201, 1212 & 1207).

Painting to old wood work and flush shutters with two coats of synthetic enamel paint Grade-II VOC (Volatile Organic Compound) content less than 50 grams/litre of approved brand and shade including cost and conveyance of all materials to site and all labour charges etc. complete, sales & other taxes on cost of all materials etc.and overheads & contractors profit complete (APSS No.1200, 1207 & 1211) in all floors.

Masonry work in CM(1:6) prop (Cement : Screened sand) with fly ash cement / lime solid blocks of size 290mm x 225mm x 140mm from approved source having minimum crushing strength of 50 Kg/Sqcm. including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, excluding seigniorage charges, sales & other taxes on all materials and such as labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, overheads and contrctor profit etc., complete for finished item of work. (APSS No. 501 & 504).

Providing and fixing 28 -30 MM thick solid Wood Polymer Composite(WPC) single extruded door shutter with 3MM top and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed to the frame using 3 inch /4 inch hinges. A minimum of 4 hinges will be required for fixing the door with the frame

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM. Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member.

Providing and applying wall putty of White Cement or Polymer or Cement basedsuch as NCL/Saicoat texture paint of average 2 to 3 mm thickness over plastered surface to prepare the surfae even and smooth after throughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface clean and wipe offo loose dust , applying putty/texture paint filler by putty knife/muslin pad, air dry for 2 to 3 hours for the surface preparation including cost and coveyance of all materials to wor site and all perational incidental, labour charges etc., complete for finished item of work for external wall, excluding cost of access scaffolding.

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of 63.5x100 MM.The two Vertical members are to be joined together with the horizontal member using 8x75 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member. Sanction

Supply of Man Mazdoor for Various Patch works at various Places including cost and conveyance of all materials and Labour charges etc., complete for finished item of work. For Mason

Supply of Man Mazdoor for Various Patch works at various Places including cost and conveyance of all materials and Labour charges etc., complete for finished item of work. For Mazdoor

Supply of Man Mazdoor for Various Patch works at various Places including cost and conveyance of all materials and Labour charges etc., complete for finished item of work. For Welder

Supply of Man Mazdoor for Various Patch works at various Places including cost and conveyance of all materials and Labour charges etc., complete for finished item of work. For Carpenter

Painting to old walls with 2 coats of acrylic emulsion paint weather proof water-based, modified acrylic with silicon additives internal grade having VOC (Volatile Organic Compound ) content less than 50 grams/ liter. approved brand,of first grade over cement primary making 3 coats in all to give an even shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance of all materials to work site and operational, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work as per SS911 for internal walls.

Painting to old walls with 2 coats of acrylic emulsion paint weather proof water-based, modified acrylic with silicon additives exterior grade having VOC (Volatile Organic Compound ) content less than 50 grams/ liter. approved brand,of first grade over cement primary making 3 coats in all to give an even shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance of all materials to work site and operational, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work as per SS911 for External walls.

Painting to new walls with 1 coat of appropriate primer of approved brand,of first grade to give an even shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance of all materials to work site and operational, labour charges and incidental charges such as scaffolding, lift charges etc., complete for finished item of work as per SS911 for External walls.

Plastering with CM (1:3) 12 mm thick using the best river sand, including cost & conveyance of all materials, labour charges and curing etc., complete complying with standard specifications and directed during execution of work. for 10 Sq.m

Preparation and fixing of M.S. heavy grills for Trusses, Stanchions,Heavy beams and Girders using chain pulley block,derek pole arrangements etc., in position including cost of Mild Steel squares/Flats etc.,welding rods,power charges and fixing charges etc., complete.

Providing Stainless Steel Railing works including cot of pipes, fabrication charges,buffing, polishing ,lacquer finish etc., complete.

Fabrication and fixing of M.S. heavy grills for Trusses, Stanchions,Heavy beams and Girders using chain pulley block,derek pole arrangements etc., in position including cost of Mild Steel squares/Flats etc.,welding rods,power charges and fixing charges etc., complete.

Fabrication Stainless Steel Railing works including cot of pipes, fabrication charges,buffing, polishing ,lacquer finish etc., complete.

Plastering 12mm thick single coat in CM(1:5) using screened sand including cost and conveyance of all materials like cement, sand, water etc., to site, excluding seigniorage charges, sales & other taxes on all materials, and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, curing as directed by Engineer-in-charge etc., and overheads & contractors profit complete for finished item of work.(SS 901,903 & 904)

Cleaning of the surface : For Waterproofing treatment ( If the surface is detoriated or damage / existing tiles or block laying) Chipping with pneumatic power chiseling equipment and until to ahcieve the hard mother concrete surface. Duly removing of debris, cleaning of the surface from dirt, dust and other foreign matters & water jet cleaning etc., complete for finished item of work.

SPECIALISED INJECTION GROUTING WITH CEMENT AND CRYSTALLIZATION ADMIXTURES : a]. Drilling of holes with power drilling machine to the required depth [12mm to 14mm dia holes] b]. Fixing of Rubber Nozzles with cement and quick c]. Grouting of holes with 140 PSI Grout pump with cement slurry mixing with Specialized crystallization compound-Roofex gp or equavalent @ 5% by weight of cement. d]. After completion of grouting, Remove the Rubber nozzles e]. Later sealing of the hole with polymer cement putty-ROOFCRETE AR (Armstrong ) / ZORIGROUT CMG (PMCC) / POWER n GUARD ARM (EBT) / WATERSHIELD AR / Fosroc NITOBOND AR + Cement Grouting Points

CRACKS AT TERRACE / BEAM & WALLS JUNCTIONS - SEALING THEJOINTS WITH POLYURETHANE SEALANT : SPECIALISED POLYURETHANE SEALANT TREATMENT : a). Making ‘’U” Groove (width and depth of 6mm x 6mm) b). Filling of the groove with polyurethane sealant – ROOFSEAL PU (Armstrong ) / POWER n SEAL PU (EBT) / THIOFLEX 600 (Fosroc) / ZORISEAL PU (PMCC) / SIKAFLEX PRO -3 WF (Sika ) WATERSHIELD PU 3

Supply and applying of the bound agent with Mix Bound AC, water and cement (2:1:3) (Mix Bound AC:Water:Cement) etc complete for lowest Quotation rate

Providing impervious coat to exposed RCC roof slab surfaces to required slopes with CM (1:3) prop. using screened sand 20mm thick (average) mixed with water proofing compound manufactured by reputed manufacturers as approved by Engineer-in-charge at 1 Kg per one bag of cement, laid over roof slab when it is green, finished smooth with a floating coat of neat cement and thread lining at regular intervals of 45cmx45cm including cost and conveyance of all materials like cement, sand, water proofing compound, water etc., to site, excluding seigniorage charges, sales & other taxes on all materials and operational, incidental, and labour charges for mixing mortar, laying, lift charges, rendering smooth and thread lining, curing including rounding off junctions of wall and slab etc., and overheads & contractors profit complete for finished item of work. (APSS No. 901 & 903).

Providing and laying five layerswaterproofing cum heat reflective treatment (MIXGUARD HR5 or equivalent) over the old / new roof slab/terrace, all as directed by Department Engineer-in-charge with the following specification and should be complain with the following technical parameters for the system a ) First Layer - Supply and Apply penetrative cum bonding primer as base primer cum sealer coat using MIXPRIMEAC100 or equivalent modified with waterand cement at the ratio 2:1:3 (MIXPRIME AC 100 : water : cement) by volume with a slow speed mixer machine. This compound shall be applied with sufficient thickness to cover the holes/pores/cracks @ 1.000 Liter /SQM (0.350 Lt of MIXPRIME AC100/SQM) and the raw primer should be complain with ASTM 4541 and the Solidcontent 49% +2% b ) Second Layer – Supply and apply of 2 x2 mm welded with alkaline resistantcoated/ non-woven 40 Gsm verging fiber mesh MIXMAT GFM 50 or equivalent for aminimum over lap of 100 mm embedded in the primer coat c ) Third Layer - Supply and apply of bonding cum water tight acrylic highviscous white primer MIXPRIME AC orequivalent @ 0.250 Kg / SQM (dilutionor modification not recommended) should be complain with Density: 1.1gm/cc, Solids content: 50 % ± 2%by weight, Elongationat break ASTM D 638: 300%, Adhesion to substrateASTM D 4541: 1 N/mm2,Tensile strength ASTM D 638: 1.5 N/mm2, Reduction in chloride ion ingress: 94%@28 days d ) Fourth Layer – Supply and apply of high elastomeric acrylic waterproofing cum weather proof high viscous white liquid membrane MIXGUARD HR or equivalent @ 0.500 Kg / SQM (dilution or modification not recommended) should be complain with Density: 1.30 gm/cc , Solids content: 68% ± 2% by weight, Elongation at break ASTM D 638: 400%, Tensile strength ASTM D 412: 1.8N/mm2, Adhesion to substrate ASTM D 4541: 1 N/mm2, Water penetration DIN1048: no leak at 7 bars (+ve side), Water vapor transmission ASTM E96: 19g/m2/day, Crack bridging ASTM C836: No cracks up to 2mm thick. E ) Fifth Layer - Supply and apply of fiber reinforced flexible high bride pure acrylic modified waterproofing cum heat reflective high viscous white liquid membrane MIXGUARD HRXtra or equivalent @ 0.500 Kg / SQM (dilution or modification not recommended)Density: 1.3 gm/cc Solids content: 68% ± 2% by weight, Elongation at break ASTM D 638: 200% , Adhesion to substrate ASTM D 4541: 1.3 N/mm2, Water penetration DIN 1048: no leak at 7 bars, Tear resistance ASTM D 1004-76: 15N/mm2 , Tensile strength ATM D 412-87: 3.0N/mm2, Solar reflectance –ASTM G173 – 92 %, Water vapor transmission ASTM E 96 – 19 Kg / M2 / day. Note: - 1 ) No dilution or modification recommended for item No.b,c,d and e . 2 ) All materials should be procured as perthe consumption with respect of the work order. 3 ) The application should be carried out by an approved agency. ) The contractor should provide 5 years material warrantee from the Manufacturer and 5 year warrantee from the applicator or combined

EXPANSION JOINT TREATMENT Prepration of the surface: For existing expansion joint treatment :Chipping of the exisiting treatments over the expa nsion joints concrete /brickmasonry with pneumatic power chiseling equipment and until to ahcieve the hard mother concrete surface.Chipping and removing of existing bituminous mastic boad upto 25mm deep. Duly removing of debris, cleaning of the surface from dirt, dust and other for eign matters

SPECIALISED POLYSULPHIDE SEAL ANT TREATMENT TO THE EXPANSION JOINTS ON TERRACE: (Size:25mmx12mm) Application of one coat of-High performance specially designed SBR l atexpolymer based bonding agent–ROOFBOND SBR (Armstrong) /POWERnBONDSBR(EBT) /NITOBONDSBR(Fosroc)ZORIBONDSBR(PMCC)/SIKALATEX(Sika)WATERSHIELD BOND SBRASTM - C920 95/DIN18549TT-S-00227E or equivalentmixing with cement as per manufacturers C) Providingandapplication of Acrylic Polymer modifiedreinstatement concrete/mortaradmixturewith ROOF CRETEAR (Armstrong)/ZORIGROUTC MG(PMCC)/POWERnGUARDARM(EBT)/WA TERSHIELDAR/ Fosroc to finish the damaged edges of jointand making the groove. D) Providing and fixing of masking tape on top of the joint bothsides. E) Providing and fixing of Back up support material of Polyethelene foamto leave the depth of 12mm on the joint. F) Providing andapplication of one coat of polysulphideprimer with Polysulphide primer on inner edge on joints. G) Providing and application of Twopart Polysulphide sealant to a width of 25 mm and 12 mm depth with ROOFSEALPS (Armstrong)/ POWERnSEALPS (EBT) /NITOSEALPS200(Fosroc)/ZORISEAL PS(PMCC) / SIKA

Dismantling doors , windows and clear storey windows, Ventilators etc., ( wood or steel ) shutters including Chowkhats , architraves,hold fasts and other attachments etc., and stacking them within 100m lead including labour charge etc., and overheads & contractors profit complete for finished item of work Doors and frames

Supplying and fixing of 4" (101.6mm) multi floor trap with jali - UPVC/SWR pipe fittings (Prince/Sudhakar/Kisan/Supreme or any other ISI Brand) as per site requirements with standard practice for all floors including cost and conveyance of all materials to site, labour charges , overheads & contractors profit etc., complete for finished item of work.

Plain Cement Concrete (1:2:4) (cement: fine aggregate: Coarse aggregate) for foundations and under flooring bed using coarse aggregate 20mm size hard , machine crushed granite from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, excluding seigniorage charges, sales & other taxes on all materials and including all charges for machine mixing, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc.,and overheads & contractors profit complete for finished item of work. (APSS No. 402)

Supply and fixing of Ventilator Frame Section 1200x600mm. The two vertical members are to be jointed together with the horizontal member usinh 8x50mm long MS star full thread screws to be used with reverse forward speed control hand drilling machine. The Ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. Aminimum of 4no's of screws to be provided for each vertical member and minimum 3no's for horizontal members etc., for complete finished item of work.

Flooring with glazed vitrified tiles with matt finish of size 600 x600mm and thickness between 9-10 mm , 1st quality and of size as approved by Engineer-in-charge, set over base coat of cement mortar (1:6), with Laticrete tiles adhesive & jointed neatly with Epoxy emulsions paste to full depth mixed with including cost of all materials etc., and overheads & contractors profit complete for finished item of work. (APSS No.701 & 707).

Providing skirting to internal walls to 15 cm height/risers of steps with 25 mm thick polished Shahabad stone length equal to flooring stones, set over base coat of CM (1:3) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointed with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like Shahabad stone, cement, sand and water etc., complete including seigniorage charges, etc., complete for finished item of work,

Constructing 904.0 mm ( 3 feet ) dia brick masonry inspection chamber as per IS - 4111: Part-1:1986 with cement mortar (1:6) prop using 2nd Class Clay Bricks of 225 mm thick from approved source having a minimum crushing strength of 5 N/sq.mm including plastering with cement mortar 1:3 prop; ½” thick both inside and outside fitted with 20” dia RCC manhole covers and frames including excavating pits up to a depth of 904 mm (3'-0") in all sorts of soils (exculding rock) and laying cement conrete (1:4:8) 150 mm thick using 40 mm HBG Metal and P.C.C. 1:2:4 benching and channel 100 mm thick as per Standard specification and including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, cost of seigniorage charges on all materials and all incidental and operational, labour charges like mixing cement mortar, constructing masonry, lift charges, curing , overheads & contractors profit etc., complete for finished item of work as per Standard specification. ManHole

Constructing 457.2 mm x 457.2 mm brick in CM 1:6 prop. Masonry. Inspection chamber upto 914.4 mm ( 3 feet ) and fitted with light weight 457.2 mm x 457.2 mm C.I frame and cover of 20 Kg including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, cost of seigniorage charges on all materials and all incidental and operational, labour charges like mixing cement mortar, constructing masonry, lift charges, curing , overheads & contractors profit etc., complete for finished item of work as per Standard specification. Man Hole

Supplying and fixing 580mm x 440mm long Orissa pan white glazed Water Closet 1st quality ISI marked confirming to IS:2556-Part-3-1981 with P or S trap Hindware / Parryware / Neycer with brick - ISI mark and providing masonry seat, CC squatting plate and 10 litres capacity single flush PVC low level cistern Parryware or equivalent with internal components fixed on 2 Nos. of teak wood blocks of size 76.20mm x 101.60mm using required size of nails, screws as approved by Engineer-in-charge, 12.70mm PVC connection with brass union nuts CP coated , 31.75mm brass plumber union, P trap or S trap of Indian W.C. shall be encased on CC (1:2:4) 150mm alround well above the joint to stop leakage at the joint etc., complete including cost and conveyance of all materials to site, cost of CC bed, labour charges and seigniorage charges, overheads & contractors profit etc., complete for finished item of work. Orissa pan

Supplying and fixing European Water Closet of 1st quality conforming to IS:2556-Part-2-1973 of Hindustan / Neycer or Parryware make white glazed with 'S' trap,supplying and fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS 2548-1996 and 10 litres capacity single flush PVC low level cistern Parryware or equivalent with internal components and fixed using required size of nails and screws, 12mm PVC connections with brass union nuts CP coated including cost and conveyance of all materials to site, overheads & contractors profit etc., complete for finished item of work for all floors.European Water Closet

Supplying and fixing Indian make Flat Back Wash Hand Basin (HSW/Parryware/ Neycer) 1st quality conforming to IS:2556-Part-4:1972 of size 550mm x 400mm with 32 mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams Seiko/Senior/Nice or equivalent complete with standard CI brackets including wooden blocks ,1 No.12.70mm PVC connection with brass union nuts CP coated , 1 No.12.70mm NP bib tap 400 gms Seiko or equivalent , 31.75mm dia. PVC flexible waste pipe 914.4mm length of 1st quality including cost and conveyance of all materials to site, labour charges , overheads & contractors profit for finished item of work Flat Back Wash Hand Basin

Supplying and fixing NP soap dish heavy type of approved make ISI quality with NP screws etc., complete including cost and conveyance of all materials, labour charges for fixing , overheads & contractors profit for finished item of work in all floors NP soap dish heavy type

Supplying and fixing TV shape mirror with plastic frame of size 609.6mm x 457.2mm , plywood back with NP screws 1st quality including cost and conveyance of all materials, labour charges , overheads & contractors profit for finished item of work in all floors. TV shape mirror

Supplying and fixing of 19.04mm dia , 609.6mm long aluminium anodized towel rods with brackets and aluminium screws including cost and conveyance of all materials, labour charges , overheads & contractors profit for finished item of work. aluminium anodized

Supplying and fixing 12.70mm dia NP push cock as approved by the Engineer-In-Charge including cost and conveyance of all materials, labour charges , overheads & contractors profit complete for finished item of work in all floors. NP Push cock

Supplying and fixing NP bib taps of size 12.70mm dia of Indian make heavy duty as approved by the Engineer-In-Charge including cost and conveyance of all materials, labour charges , overheads & contractors profit complete for finished item of work in all floors. NP bib taps of size 12.70mm dia

Supplying and fixing of SWR PVC pipes (Prince/Sudhakar/Kisan/Supreme or any ISI brand) 4 Kg/Sq.cm. and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with PVC clamps if necessary with required number of Bombay nails including cost and conveyance of all materials to site, labour charges, overheads & contractors profit complete for finished item of work at all floor levels. (APSS No. 1302 1319 & 1326) 75 mm dia pipe

Supplying and fixing of SWR PVC pipes (Prince/Sudhakar/Kisan/Supreme or any ISI brand) 4 Kg/Sq.cm. and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with PVC clamps if necessary with required number of Bombay nails including cost and conveyance of all materials to site, labour charges, overheads & contractors profit complete for finished item of work at all floor levels. (APSS No. 1302 1319 & 1326) 110 mm dia pipe

Supplying and fixing of SWR PVC pipes (Prince/Sudhakar/Kisan/Supreme or any ISI brand) 4 Kg/Sq.cm. and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with PVC clamps if necessary with required number of Bombay nails including cost and conveyance of all materials to site, labour charges, overheads & contractors profit complete for finished item of work at all floor levels. (APSS No. 1302 1319 & 1326) 110 mm dia pipe