Eastern Power Distribution Company Of Andhra Pradesh Limited Tender

Masonry in CM (1:6) with fly ash cement solid blocks of size 290x225x140mm including cost and conveyance of all materials to site and all labour charges complete.

Plastering with CM (1:5), 20 mm thick in one coat for external faces of walls including cost and conveyance of all materials all labour charges etc, complete..

Supply and fixing of Mild Steel pipes of required size and thickness including fabrication charges for Verticals, Horizontals & purlins with two coats of synthetic enamel paint of grade-I over a coat of red oxide primer Grade-I including cost and conveyance of all materials to site and labour charges and including wastage of iron materials during fabrication, complete for finished item of work.

Roofing with Pre-painted Galvalume Trapezoidal Profile Roofing sheets with 0.5mm thickness, coating: Alu-Zinc coating AZ150 GSM. Tensile Strength:550MPA.Paint coating: Regular Modified Polyester painting, painting Thickness (Top): 18 to 20 Microns,(Bottom): 5 to 7 Microns; Sheet Width: 1.020, Length: Maximum 12 meters with Regular Range Colours fixed to the purlins with 1/4" size self drilling screws with neoprene washer. side laps are stiched with self tapping/drilling screws. End laps are to be sealed with 25x3mm Butyl tape. The sheets are provided with anti capillary groove and supply and fixing of roof accessories medium size: Ridge, Barge Cap, Corner Trim, L-Flashing, Down Pipes, Gutter etc., with 0.47mm thick, Width:0.585, Length:Maximum 2.5Metres including lapping and wastage and cost and conveyance of all materials to site and all labour charges complete.

PCC (1:2:4) using 20 mm size HBG metal from approved quarry including cost and conveyance of all materials and all labor charges for laying of concrete with all leads and lifts and all other incidental charges etc., complete.

Flush door: supply and fixing of 35 mm thick flush door single shutter, solid bond wood block board type with teak veneer on both faces including 5mm thick glass and supplying positioning and fixing door frame with well seasoned assam teak/beeja sal/sal wood scantlings of size 100 mm x 75 mm, including 6 nos. Of ms 'z' hold fasts of size 250x50x8 mm,including aluminium 3 nos. Of 125 mm butt hinges, 1 no. Door stoper, 2 no. 100 mm long door handles , 1 no. Aldrop of size 250 mm long , 1 nos. Of 200 mm long tower bolts, with bolts, nuts, nf screws including cost and conveyance of all materials to site, labour charges etc., including minor extra fixtures required if any as directed by the engineer-in-chrge of the work complete for finished item of work

Supply & fixing of windows with well seasoned country wood with outer and centre frame size 3" x 4" ( Sal wood / Kamba wood ) with hold fasts with two shutters with 5mm thick pinheaded glass panels including cost of wood, cost of making charges and fixing iron grills of approved design with 9mm size square rod and aluminium accessories like window stay, tower bolts, hinges etc., including painting two coats with synthetic enamel paint over coat of wood primer with putty including cost and conveyance of materials, labour charges, hard ware, fixing etc., complete.

Supply and Fixing of 25mm outer dia 1.8mm thick rigid P.V.C. pipe (ISI MARK) of make Sudhakar/Macoplast/ Modi with all required accessories like bends, junction box with cover etc., including all labour charges etc., complete.

Wiring with 2 runs of 14/0.3mm (1.0 Sq.mm) Fire Retardant (FR) P.V.C. insulated flexible copper cable (ISI MARK) in existing pipe with 6A modular switch, Ceiling rose and hot dip galvanized metal boxes with cover frame to switch control box including all labour charges etc., complete for light, bell, fan and exhaust fan points in Non-Residential Buildings (makes Anchor / Gold Medal / Million / Vimal / Maru / Milltec.)

Wiring with 2 of 14/0.3mm (1.0 Sq.mm) P.V.C. insulated F.R. flexible copper cable (ISI MARK) in existing pipe with 6A modular switch control and 3/2 pin sockets with hot dip galvanized box with cover frame on separate board including all labour charges etc., complete.

Supply and run of 2 of 14/0.3mm (1.0 Sq.mm) F.R P.V.C. insulated flexible copper cable in existing pipe for mains inlcuding all labour charges etc., complete.

Supply and fixing of Supply and fixing of 20-24W, not less than 1100mm length LED batten light with extruded aluminum housing and polycarbonate cover, input voltage AC 220 - 260 Volts, with high power LED lights with inbuilt driver and frosted cover and all standard accessories etc., complete of makes Crompton/ Bajaj/ Surya/ Havells

Painting with white cement (Birla / JK white / Surya cem or other equivalent quality) one coat of approved quality to give an even shade including cost of all materials, labour charges and incidental such as scaffolding, lift charges etc., complete for finished item of work, including conveyance charges of materials complete for finished item of work.

Supplying, cutting and placing HYSD bar reinforcement as per drawings and technical specifications for Bars below 36 mm dia including over laps and wastage, where they are not welded including cost and conveyance of all materials to site and all labour charges complete.

PLINTH : RCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering with wooden scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

COLUMNS : RCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering with wooden scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

SUN SHADES & CHAJJAS : RCC M- 20 Nominal mix (1:1.5:3) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry g cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing and steel centering with wooden scaffolding etc.,complete but excluding cost of steel and its fabrication charges for finished item of work.

Supply and fixing of CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS aluminum glazed partitions using 10 MM CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS and 5.00 mm thick plain glass to full height. Using with LAM to a height of 0.91 meter at bottom panel and remaining height with glass and aluminum sections anodized to 12 to 15 microns and of sections of size 37mm x 62mm and 1.5mm thickness with one meter centre to centre duly fixed with clip beading on both sides including fixing the frame to pillars by M.S. flats, bolts and nuts including cost and conveyance of all materials etc., complete as directed during execution.

Supply and fixing Aluminium Single Shutter door partly Glazed &Panneled with aluminium anodised sections of Jindal sections Shutter frame top of size 44.45 mm x 47.62 mm x 1.95 section 19571 , bottom of size 44.45 mm x 114.30 mm x 2.15 section 19574 and verticals of 19569 of size 44.45 mm x 47.62 mm x 2.02 and fitted with 10mm thick both sides prelaminated cement particle board and 5mm thick plain glass for shutter and other acccessories like supply and fixing aluminium handles, door stoppers, latches, etc.,for each shutter, and all labour charges for fixing the fixtures with required no.of screws, bolts and nuts and including labour charges for fixing the frame in position, fixing shutter to frame etc. completed for finished item of work

Providing and fixing Aluminium Extruded Section Body Tubular Type Hydraulic Door Closer (IS: 3564) with double speed adjustment with necessary accessories and screws etc. complete (Type-3: for width of doors 851 to 1000 mm)

Supply of 1.8/1.9/2.0TR, 3 Star capable of delivering not less than 21600 BTU/hr and above with operating on refrigerant R-410A / R-32 INVERTER Model Cool type split AC unit with high wall mounted Single Split indoor unit and outdoor condensing unit Hermetically sealed compressor suitable for operation on 230V, 50Hz, 1Phase AC supply capable of performing Heat cool dehumidifying air circulating and filtering with cooling and condensing units with 3 mts of copper piping, insulation kit and 4 mts of 4 core copper flexible chord with cordless remote control etc., dual barrier coating in order to protect coil form oxidation. Makes: / Hitachi / Blue Star / Daikin / Voltas /Carrier/ LG/Lloyd (prevailing models in the market)

Supply and istallation of 5.0KVA Stabilizer of Makes: V-Guard / Real Guard / Uni Stab / ITL.

Supply and fixing( Positioning) modular panel based 8 units work station of size 4’x 4' x4’ double skinned partition of 62 mm (+/-5%) thick made out of extrude Aluminium sections powder coated with 12mm thick pre-laminated particle board panels/soft board / marker board panels, all the exposed metal surfaces of supports, top covers and hardware for fixing furniture to partition is to be powder coated with approved colour/Shade of 50 micron thick and provision for built in cable management provided with 2 No integrated wire ways of 130mm high, provided one each at skirting level and other at just below / above the work top (table ) level. The minimum free space required in the wire ways to accommodate power, data and communication cables is to be 30mmx120mm with injection moulded ABS end caps and with side partitions for every work station and with the front walls below the table top only (Switches and sockets of RAW power/ UPS /Data /Telephone shall be recessed).Provision should be made for three 5 amp socktes (one with switch control) and telephone jack, just below/above table top and one 5amp switch and one number RJ 15 and one No RJ 45 socket for LAN point below table top. The table top with PLB 25mm thick particle board edge pressed with pvc tape and the surface top with all exposed edges duly edge banded. The pin board is made of 12 mm thick soft board covered with approved colour/ shade /design/ texture fabric. The partition is to be provided with leveling bolts to account for any unevenness in the floor. The work station provided with table top of width of 2' (600 mm) and height of table top is 750 mm from the floor level. Key board tray with high impact plastic and C P U stand/ trolley and PLB 3 draw pedestal unit of size 450 x 500 x 650 mm as per approved design, make and accessiores and as per drawing and directions of Eng-in- charge .

Supply and fixing( Positioning) modular panel based 4 units work station of size 4’x 4' x4’ double skinned partition of 62 mm (+/-5%) thick made out of extrude Aluminium sections powder coated with 12mm thick pre-laminated particle board panels/soft board / marker board panels, all the exposed metal surfaces of supports, top covers and hardware for fixing furniture to partition is to be powder coated with approved colour/Shade of 50 micron thick and provision for built in cable management provided with 2 No integrated wire ways of 130mm high, provided one each at skirting level and other at just below / above the work top (table ) level. The minimum free space required in the wire ways to accommodate power, data and communication cables is to be 30mmx120mm with injection moulded ABS end caps and with side partitions for every work station and with the front walls below the table top only (Switches and sockets of RAW power/ UPS /Data /Telephone shall be recessed).Provision should be made for three 5 amp socktes (one with switch control) and telephone jack, just below/above table top and one 5amp switch and one number RJ 15 and one No RJ 45 socket for LAN point below table top. The table top with PLB 25mm thick particle board edge pressed with pvc tape and the surface top with all exposed edges duly edge banded. The pin board is made of 12 mm thick soft board covered with approved colour/ shade /design/ texture fabric. The partition is to be provided with leveling bolts to account for any unevenness in the floor. The work station provided with table top of width of 2' (600 mm) and height of table top is 750 mm from the floor level. Key board tray with high impact plastic and C P U stand/ trolley and PLB 3 draw pedestal unit of size 450 x 500 x 650 mm as per approved design, make and accessiores and as per drawing and directions of Eng-in- charge .

Executive Chair Type - I - High Back (OXBO) SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D). BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm (W) x 70.5 cm (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features: • 360° revolving type. • 17° ±2° maximum tilt on pivot at centre • Upright position locking. Tilt tension adjustment. . PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon.Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm. Height - min 99.5 to max 110.5cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm

Executive Chair Type- II - Mid back (OXBO) SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D). BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm (W) x 60.5 cm (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features: • 360° revolving type. • 17° ±2° maximum tilt on pivot at centre • Upright position locking. • Tilt tension adjustment. . PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon.Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm. Height - min 89.5 to max 100.5cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.