Department Of Education Tender

Ceiling plastering with CM (1:3), 12mm thick including cost and conveyance of all materials and all labour charges etc., complete.

Supplying, fitting and placing MS grilled door, windows including cost and conveyance of all materials and all labour charges etc., complete.

White washing Two coats with Whiting of approved quality to give an even shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost of all materials, labour charges such as scaffolding, lift charges etc., complete for finished item of work.

Painting to walls with two coats of acrylic emulsion paint of approved brand and shade over a base coat of approved cement primer of exterior grade-2 making 3 coats in all to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete for finished item of work as per SS 912 for external walls.

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM. Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 no.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member. Providing Wood Polymer Composite (WPC) solid, frostywhite single extruded factory made 2.44 mt x 1.22 mt boards in 18 MM thickness (Density 650 kg/Cum, Weight 35Kg). including labour charges for fixing the frame in position, fixing the board to the frame etc., complete for finished item of work. Doors

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM. Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 no.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member. Providing Wood Polymer Composite (WPC) solid, frostywhite single extruded factory made 2.44 mt x 1.22 mt boards in 18 MM thickness (Density 650 kg/Cum, Weight 35Kg). including labour charges for fixing the frame in position, fixing the board to the frame etc., complete for finished item of work. Doors

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVCprofile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM (white powder coated) touch locks with hook, gasket, wool pile, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screwsetc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge inclusive of cost of Single / double glass panes, wire mesh and silicon sealent .

Providing 110 mm Dia ISI marked PVC down water take pipes with socket, 2.5mm thick 4.0 kg/sq.cm pressure of ISI marked including cost of necessary PVC Bends, shoes, iron/ PVC clamps and all other accessories and fixing in position including cost and conveyance of all materials, operational & incidental charges including all labour charges for fixing at site etc., for finished item of work.

Providing 75 mm Dia ISI marked UPVC down water take pipes with socket, 2.5mm thick 4.0 kg/sq.cm pressure of ISI marked including cost of necessary PVC Bends, shoes, iron/ PVC clamps and all other accessories and fixing in position including cost and conveyance of all materials, operational & incidental charges including all labour charges for fixing at site etc., for finished item of work.

Supplying & Fixing 12.7mm N.P bib tap Indian make heavy duty including cost and conveyance of all materials, operational & incidental charges including all labour charges for fixing at site etc., for finished item of work.

Supply and Fixing of Premium make CPVC 15.90 mm OD Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2") Ashirvad Flowgurard SDR 11 and SDR 13.5 for Hot and Cold Water including cost and conveyance of all materials, operational & incidental charges including all labour charges for fixing at site etc., for finished item of work.

Supply and Fixing of Premium make CPVC 22.20 mm OD Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2") Ashirvad Flowgurard SDR 11 and SDR 13.5 for Hot and Cold Water including cost and conveyance of all materials, operational & incidental charges including all labour charges for fixing at site etc., for finished item of work.

Constructing 457.2 mm x 457.2 mm (1'6"x1'6") brick in CM 1:6 prop. Masonry. Inspection chamber up to 914.4 mm (3'0") and fitted with light weight 457.2 mm x 457.2 mm (1'6"x1'6") C.I frame andcover of 20 Kg.

Providing & Placing on Terrace(at all floor levels) polyethylene water storage tank with Double layer approvedbrand & manufacture with cover and suitable locking arrangement & making necessary holes for inlet & outlets and over flow pipes but without fittings & base support for tanks.

Supply and erecting, ISI mark submersible 1.5 HP, Single Phase 21 stages pumpset suitable for 106/ 156mm dia borewell with high quality water resistant and dynamically balanced bronze impeller with stainless steel shaft sleeves, pump coupling and pivot of Single phase 250V, 50Hz.. A.C. power supply copper winding with water proof insulation and high precision strength not to be effected by chemical in water and suitable bronze bearings with nut and bolts etc., with necessary H-type clamp of suitable size and strength.3

Drilling of Bore well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation, all consolidated formation etc. and drilling in over burden to dia not less than 200 mm etc and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore Well at an average pressure of 150 PSI) conducting yield test, consumables charges, Crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges but excluding all taxes, the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS -2800 Part I & II 1979 and amended from time to time.

Supply and utilisation of 180 mm dia UPVC casing pipe of class 3 ( 6 kg/cm2) for bore wells for potable water supply confirming to IS 4985/1988 as amended from time to time including revisions if any and confirming to technical conditions and specification

Supply and utilisation of 250 mm dia UPVC casing pipe of class 3 ( 6 kg/cm2) for bore wells for potable water supply confirming to IS 4985/1988 as amended from time to time including revisions if any and confirming to technical conditions and specification

Supply and Transportation of Outer dia 50mm and Inner dia 38mm double walled corrugated HDPE duct made as per specification BSEN - 500 86/IS 14930 Part-II. Makes: DURA LINE (Dura Guard) or its equivalent make.

Supply of 3 Core 2.5 sqmm Flat Copper cable of ISI for Submersible Motors confirming to IS:694:1990. Makes: Finolex/ RR Kabel/ Polycab/ Havells/ KEI/Gloster

Fabrication , transportation and supply of suitable size panel board for single phase submersible motor upto 1.5HP consisting of relay, Contactor, starting and running capacitors, Voltmeter, Ammeter, indicator lamps, MCB , on/off switch including supply and fixing of DOL starter of make C&S/LTLK/Seimens/BCH/Crompton. complete.,

Supply and fixing of 25mm dia 1.8mm thick P.V.C. pipe (ISI Mark) concealed in wall with all required accessories including masonary work and labour charges etc., complete.

Supply and fixing of 16A 3pin flush type switch socket combined (2 in 1) duly recessed in wall with wooden deep box of 6"x8"x21/2" size covered with hylam sheet including earth connections and all labour charges etc., complete.

Supply and fixing of 6A 3 pin wall plug socket with a 6A switch control on a common switch board with earth continuity including wire leads, earth connections along with all labour charges etc., complete.

Supply and run of 2 of 36/0.3mm (2.5 Sq.mm) F.R. P.V.C. insulated flexible copper cable in existing pipe for mains including all labour charges etc., complete.

Wiring with 2 runs of 14/0.3mm (1.0 Sq.mm) Fire Retardant (FR) P.V.C. insulated flexible copper cable (ISI MARK) in existing pipe with 6A switch, Ceiling rose and 3mm tick hylam sheet covering to switch control box including all labour charges etc., complete for light, bell, fan and exhaust fan points in Non-Residential buildings.

Supply and fixing of 20W,2400 lumens T8, , not less than 1100 mm length LED retrofit tube light with aluminium anodised body, input voltage AC 220 -260 Volts with PF0.9, Surge protection: 2KV,THD10%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI70, .etc.,complete. as per IS 10322 (Part 5/ Sec 1)..2012Makes : As per list of recommended brands as category I.

Supply of 1200mm (48") Sweep 230V, A.C 50 Hz Ceiling Fan with 3 blades and double ball bearings with all standard accseeories.

Supply of stepped type electronic Regulator

Labour charges for fixing of ceiling fan and regulator including transportation and giving connections with twin core wire etc., complete.

Supply of 1x40W weather proof flourescent street light fitting comprising canopy of sheet Aluminium in stove enamel finish with copper/ VPIT ballast, capacitor, tube and starter etc., complete.

Fixing of 40W street light luminaire to the wall with 1.0 Mtr., 25mm dia GI pipe bracket and anti tilting MS flat etc., including giving connections and labour charges etc., complete.

Supply and fixing SPN Distribution board with IP-42 protection (Metal Door) suitable for single phase ELCB / RCCB / DP Isolator as incomer and 10kA SP MCBs as outing going including internal connection and labour charges for surface/ flush mounting etc., complete.

Supply and fixing TPN Distribution board with IP-42 protection (Metal Door) suitable for 3 phase ELCB / RCCB / FP Isolator as incomer and 10kA SP MCBs as outing going including internal connection and labour charges for surface / flush mounting etc., complete.

Provosion of Name Board