Andhra Pradesh Urban Greening And Beautification Corporation Limited Tender

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Providing High Yield Strength Deformed (HYSD) / Thermo Mechanically Treated (TMT) (Fe 500 / Fe 500D grade as per IS 1786-1979) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including overheads & contractors profit complete for finished item of work.( APSS No.126)

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Masonry work in CM(1:6) prop (Cement : Screened sand) in superstructure with fly ash cement / lime solid blocks of size 290mm x 225mm x 140mm from approved source having minimum crushing strength of 50 Kg/Sqcm. including cost and conveyance of all materials like cement, sand, bricks, water etc., to site,and such as labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, overheads and contractor profit etc., complete for finished item of work. (APSS No. 501 & 504).

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Plastering 12mm thick in two coats using screened sand with base coat of 8mm thick in CM (1:6) and top coat of 4mm thick in CM (1:4) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site, ,, and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, scaffolding, lift charges, curing, including cutting grooves as directed by Engineer - in - charge etc., and overheads & contractors profit complete for finished item of work. (SS 901,903 & 904)

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply & application of one coat water based cement primer of exterior grade II and two coats of acrylic exterior emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/litre for exterior walls including cost and conveyance of all materials to site,and all operational, incidental, labour charges etc., and overheads & contractors profit complete for finished item of work in all floors.

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply and fabrication of MS framed structure like Window Grills, Compound Wall Grills, Iron Doors, Windows, Gates, MS Frame for chain link mesh works, Roof Trusses by using square / rectangular MS hollow section as per IS 4923 & Angles as per SP:6(1) IS Hand book, including cost of welding rods, power charges, labour charges for cutting, placing, welding and erecting in position and fixing, cost & convenience of all materials including wastage to site and complete for finished item of work

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply and fabrication of MS framed structure like Window Grills, Compound Wall Grills, Iron Doors, Windows, Gates, MS Frame for chain link mesh works ,Roof Trusses by using MS Flats as per SP:6(1) IS Hand book , including cost of welding rods, power charges, labour charges for cutting, placing, welding and erecting in position and fixing, cost & convenience of all materials to site and complete for finished item of work

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply and fabrication works like Window Grills, Compound Wall Grills, Iron Doors, Windows, Gates, Roof Trusses by using MS solid plate section as per IS 1730 including cost of welding rods, power charges, labour charges for cutting, placing, welding & erecting in position and fixing cost & convenience of all materials including wastage to site and complete for finished item of work.

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Painting to new iron work with one coat of Red oxide primer and two coats with synthetic enamel paint Grade-I VOC (Volatile Organic Compound) content less than 50 grams/litre over primer coat of red oxid, including cost and conveyance of all materials like Red oxide primer, Synthetic Enamel Paint to site, incidental, operational and all labour charges etc., and overheads & contractors profit complete for finished item of work in all floors. (SS No. 1201, 1212 & 1207).

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supplying and fixing G.I. Chain link TATA make fencing of required width in mesh size 50x50 mm opening of 4 mm dia GI wire including strengthening with 2 mm dia wire or nuts, bolts and washers/welding in the MS angle frame/ RCC fencing posts as required complete as per the direction of Engineer-in-charge and including cost of all materials to site, incidental operational and all labour charges overheads & contractors profit etc., complete for finished item of work

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply and laying of 3/8" turfted synthetic grass type (artificial) of 35mm pile height of fibre colour 4 field green + 4 olive green, root zone 4 jute+ 4 field green with covering of 14 stitches per 10 cm with double backing UV stable, 215 gram/sq.mt, coating with black SBR latex, duly fibres meet the most stingent environmental standards, including cost of material, transportation to the site, labor charges, etc., in complete item of work.

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply, Delivery and Commissioning of SKY WALKER with main frame shall be minimum of 80mm NB dia of thickness not less than 4.50mm & Handle pipes shall be minimum of 25mm NB dia of thickness not less than 3.60mm are of 'C' class heavy grade of TATA/JINDAL make with hot dipped galvanized with minimum of 75 microns zinc dipped joint with robotic welded with Plastic/Rubber grips on top end. The handle pipes are hinged over 80NB main frame with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. The handle pipes shall be further extended to the 32mm NB dia on both sides. Paired rectangular tubes with four foot rests are linked to main frame. Foot rest shall be made of Aluminum material - LM26 grade. Total structure is supported on base frame shall be made up of rectangular pipe of 50X50X3mm and side frames shall be made up of 32mm NB dia GI Pipes. All pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. All open ends of pipes, bearings, bushes and Base cover shall be closed by SS 304 grade Stainless Steel for safety against entrapment, corrosion & water resistant. The foundation pipe with anchoring shall be 750mm deep with minimum of 100mm NB dia supported with M.S. Angle 25X25X4mm. The instruction plate of size 150mmX230mm of SS 304 grade Plate with 0.7mm thick shall be riveted on 5mm thick plate with APG&BC emblem and your company emblem at two sides facing to users with LASER printing. All plastic parts should solid poly propylene Co-Polymer (PPCP) and UV- stabilized should be used. All products of equipment should be manufactured as per EN 16630 safety norms and to be produced proof of valid certificate conformity to EN16630.

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply, Delivery and Commissioning of THAI CHI SPINNER 4 WHEEL with center pipe shall be of minimum 100mm NB dia of thickness not less than 5.00mm, Support frame shall be minimum of 32mm NB dia of thickness not less than 3.6mm & TAI CHI SPINNER rings shall be minimum of 25mm NB dia of thickness not less than 3.60mm are of 'C' class heavy grade of TATA/JINDAL make with hot dipped galvanized with minimum of 75 microns zinc dipped joint with robotic welded with Handle knobs are made from high quality nylon material. The rings are hinged over 32NB support frame with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. All pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. All open ends of pipes, bearings, bushes and Base cover shall be closed by SS 304 grade Stainless Steel for safety against entrapment, corrosion & water resistant. The foundation pipe with anchoring shall be 750mm deep with minimum of 100mm NB dia supported with M.S. Angle 25X25X4mm. The instruction plate of size 150mmX230mm of SS 304 grade Plate with 0.7mm thick shall be riveted on 5mm thick plate with APG&BC emblem and your company emblem at two sides facing to users with LASER printing. All plastic parts should solid poly propylene Co-Polymer (PPCP) and UV- stabilized should be used. All products of equipment should be manufactured as per EN 16630 safety norms and to be produced proof of valid certificate conformity to EN16630.

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply, Delivery and Commissioning of DOUBLE AIR WALKER with three prime stand pipes shall be minimum of 100mm NB dia of thickness not less than 5.00mm, Pedestal frame shall be minimum of 32mm NB dia of thickness not less than 3.6mm & Handle frame shall be minimum of 25mm NB dia of thickness not less than 3.60mm are of 'C' class heavy grade of TATA/JINDAL make with hot dipped galvanized with minimum of 75 microns zinc dipped joint with robotic welded. The two pedestal frames are hinged over 100NB prime stand pipes with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. Foot rest shall be made of Aluminum material - LM26 grade. All pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. All open ends of pipes, bearings, bushes and Base cover shall be closed by SS 304 grade Stainless Steel for safety against entrapment, corrosion & water resistant. The foundation pipe with anchoring shall be 750mm deep with minimum of 100mm NB dia supported with M.S. Angle 25X25X4mm. The instruction plate of size 150mmX230mm of SS 304 grade Plate with 0.7mm thick shall be riveted on 5mm thick plate with APG&BC emblem and your company emblem at two sides facing to users with LASER printing. All plastic parts should solid poly propylene Co-Polymer (PPCP) and UV- stabilized should be used. All products of equipment should be manufactured as per EN 16630 safety norms and to be produced proof of valid certificate conformity to EN16630.

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply, Delivery and Commissioning of SEATED PULLER DOUBLE with prime stand pipe shall be minimum of 100mm NB dia of thickness not less than 5.00mm, Handle frame & Seat frame shall be minimum of 32mm NB dia of thickness not less than 3.6mm & Connecting links shall be minimum of 25mm NB dia of thickness not less than 3.60mm are of 'C' class heavy grade of TATA/JINDAL make with hot dipped galvanized with minimum of 75 microns zinc dipped joint with robotic welded. The two handle frames are hinged over 100NB prime stand pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. Seat & Back rests are made with the GI Sheet of size 330X330X2mm with uniform bending radius to avoid sharp edges. All pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. All open ends of pipes, bearings, bushes and Base cover shall be closed by SS 304 grade Stainless Steel for safety against entrapment, corrosion & water resistant. The foundation pipe with anchoring shall be 750mm deep with minimum of 100mm NB dia supported with M.S. Angle 25X25X4mm. The instruction plate of size 150mmX230mm of SS 304 grade Plate with 0.7mm thick shall be riveted on 5mm thick plate with APG&BC emblem and your company emblem at two sides facing to users with LASER printing. All plastic parts should solid poly propylene Co-Polymer (PPCP) and UV- stabilized should be used. All products of equipment should be manufactured as per EN 16630 safety norms and to be produced proof of valid certificate conformity to EN16630.

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply, Delivery and Commissioning of CHEST PRESS DOUBLE with prime stand pipe shall be minimum of 100mm NB dia of thickness not less than 5.00mm, Handle frame & Seat frame shall be minimum of 32mm NB dia of thickness not less than 3.6mm & Connecting links shall be minimum of 25mm NB dia of thickness not less than 3.60mm are of 'C' class heavy grade of TATA/JINDAL make with hot dipped galvanized with minimum of 75 microns ionized coated and zinc dipped joint with robotic welded. The two handle frames are hinged over 100NB prime stand pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. Seat & Back rests are made with the GI Sheet of size 330X330X2mm with uniform bending radius to avoid sharp edges. All pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. All open ends of pipes, bearings, bushes and Base cover shall be closed by SS 304 grade Stainless Steel for safety against entrapment, corrosion & water resistant. The foundation pipe with anchoring shall be 750mm deep with minimum of 100mm NB dia supported with M.S. Angle 25X25X4mm. The instruction plate of size 150mmX230mm of SS 304 grade Plate with 0.7mm thick shall be riveted on 5mm thick plate with APG&BC emblem and your company emblem at two sides facing to users with LASER printing. All plastic parts should solid poly propylene Co-Polymer (PPCP) and UV- stabilized should be used. All products of equipment should be manufactured as per EN 16630 safety norms and to be produced proof of valid certificate conformity to EN16630.

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply, Delivery and Commissioning of HORSE RIDER with main frame shall be minimum of 100mm NB dia of thickness not less than 5.00mm, handle frame & Seat frame shall be minimum of 32mm NB dia of thickness not less than 3.6mm & Connecting link pipes shall be minimum of 25mm NB dia of thickness not less than 3.60mm are of 'C' class heavy grade of TATA/JINDAL make with hot dipped galvanized with minimum of 75 microns zinc dipped joint with robotic welded. The handle frame are hinged over 100NB main frame with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. Seat & Back rests are made with the GI Sheet of size 330X330X2mm with uniform bending radius to avoid sharp edges. All pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. All open ends of pipes, bearings, bushes and Base cover shall be closed by SS 304 grade Stainless Steel for safety against entrapment, corrosion & water resistant. The foundation pipe with anchoring shall be 750mm deep with minimum of 100mm NB dia supported with M.S. Angle 25X25X4mm. The instruction plate of size 150mmX230mm of SS 304 grade Plate with 0.7mm thick shall be riveted on 5mm thick plate with APG&BC emblem and your company emblem at two sides facing to users with LASER printing. All plastic parts should solid poly propylene Co-Polymer (PPCP) and UV- stabilized should be used. All products of equipment should be manufactured as per EN 16630 safety norms and to be produced proof of valid certificate conformity to EN16630.

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply, Delivery and Commissioning of STANDING TRIPPLE TWISTER with prime pipe shall be minimum of 100mm NB dia of thickness not less than 5.00mm, Standing twister plate support pipe shall be minimum of 80mm NB dia of thickness not less than 4.5mm, Bottom frame support shall be minimum of 32mm NB dia of thickness not less than 3.6mm & Handle ring shall be minimum of 25mm NB dia of thickness not less than 3.60mm are of 'C' class heavy grade of TATA/JINDAL make with hot dipped galvanized with minimum of 75 microns zinc dipped joint with robotic welded. The twister plate is hinged over 80NB standing pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. All pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. All open ends of pipes, bearings, bushes and Base cover shall be closed by SS 304 grade Stainless Steel for safety against entrapment, corrosion & water resistant. The foundation pipe with anchoring shall be 750mm deep with minimum of 100mm NB dia supported with M.S. Angle 25X25X4mm. The instruction plate of size 150mmX230mm of SS 304 grade Plate with 0.7mm thick shall be riveted on 5mm thick plate with APG&BC emblem and your company emblem at two sides facing to users with LASER printing. All plastic parts should solid poly propylene Co-Polymer (PPCP) and UV- stabilized should be used. All products of equipment should be manufactured as per EN 16630 safety norms and to be produced proof of valid certificate conformity to EN16630.

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply, Delivery and Commissioning of 4 IN 1COMBINATION (SURF BOARD+LEG PRESS+PECK DECK + SEATING TWISTER) with all prime pipes shall be minimum of 100mm NB Dia of thickness not less than 5.00mm, 4 functions base pipes are shall be minimum of 80mm NB dia of thickness not less than 4.50mm and hinged over to prime pipe of 100mm, Handle frame & Seat frame shall be minimum of 32mm NB dia of thickness not less than 3.6mm & Connecting links shall be minimum of 25mm NB dia of thickness not less than 3.60mm are of 'C' class heavy grade of TATA/JINDAL make with hot dipped galvanized with minimum of 75 microns ionized coated and zinc dipped joint with robotic welded. The handle frames are hinged over to 80NB base link pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. Seat & Back rests are made with the GI Sheet of size 330X330X2mm with uniform bending radius to avoid sharp edges. All pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. All open ends of pipes, bearings, bushes and Base cover shall be closed by SS 304 grade Stainless Steel for safety against entrapment, corrosion & water resistant. The foundation frame pipe shall be 100mm NB with 6 numbers of self-anchoring shall be not less than 300mm deep supported with M.S. Angle 25X25X4mm. The instruction plate of size 150mmX230mm of SS 304 grade Plate with 0.7mm thick shall be riveted on 5mm thick plate with APG&BC emblem and your company emblem at two sides facing to users with LASER printing. All plastic parts should solid poly propylene Co-Polymer (PPCP) and UV- stabilized should be used. All products of equipment should be manufactured as per EN 16630 safety norms and to be produced proof of valid certificate conformity to EN16630.

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply, Delivery and Commissioning of 4 IN 1COMBINATION (SURF BOARD+LEG PRESS+PECK DECK + SEATING TWISTER) with all prime pipes shall be minimum of 100mm NB Dia of thickness not less than 5.00mm, 4 functions base pipes are shall be minimum of 80mm NB dia of thickness not less than 4.50mm and hinged over to prime pipe of 100mm, Handle frame & Seat frame shall be minimum of 32mm NB dia of thickness not less than 3.6mm & Connecting links shall be minimum of 25mm NB dia of thickness not less than 3.60mm are of 'C' class heavy grade of TATA/JINDAL make with hot dipped galvanized with minimum of 75 microns ionized coated and zinc dipped joint with robotic welded. The handle frames are hinged over to 80NB base link pipe with the help of specially heavy duty bearings should be reputed make and press fitted for smooth rotation, and does not require re-lubrication i.e., maintenance - free ball bearing. Seat & Back rests are made with the GI Sheet of size 330X330X2mm with uniform bending radius to avoid sharp edges. All pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. All open ends of pipes, bearings, bushes and Base cover shall be closed by SS 304 grade Stainless Steel for safety against entrapment, corrosion & water resistant. The foundation frame pipe shall be 100mm NB with 6 numbers of self-anchoring shall be not less than 300mm deep supported with M.S. Angle 25X25X4mm. The instruction plate of size 150mmX230mm of SS 304 grade Plate with 0.7mm thick shall be riveted on 5mm thick plate with APG&BC emblem and your company emblem at two sides facing to users with LASER printing. All plastic parts should solid poly propylene Co-Polymer (PPCP) and UV- stabilized should be used. All products of equipment should be manufactured as per EN 16630 safety norms and to be produced proof of valid certificate conformity to EN16630.

Supply, delivery and commissioning and providing infrastructure facilities to outdoor fitness equipm;Supply, Delivery and Commissioning of POMMELO HORSE with prime pipes shall be minimum of 80mm NB dia of thickness not less than 4.50mm, bottom pipe shall be minimum of 50mm NB dia of thickness not less than 4.1 mm & rest of the pipes shall be minimum of 25mm NB dia of thickness not less than 3.60mm are of 'C' class heavy grade of TATA/JINDAL make with hot dipped galvanized with minimum of 75 microns ionized coated and zinc dipped joint with robotic welded. All pipes shall be uniformly powder coated up to minimum 100 microns thickness to avoid corrosion. All open ends of pipes, bearings, bushes and Base cover shall be closed by SS 304 grade Stainless Steel for safety against entrapment, corrosion & water resistant. The foundation pipe with anchoring shall be 750mm deep with minimum of 100mm NB dia supported with M.S. Angle 25X25X4mm. The instruction plate of size 150mmX230mm of SS 304 grade Plate with 0.7mm thick shall be riveted on 5mm thick plate with APG&BC emblem and your company emblem at two sides facing to users with LASER printing. All plastic parts should solid poly propylene Co-Polymer (PPCP) and UV- stabilized should be used. All products of equipment should be manufactured as per EN 16630 safety norms and to be produced proof of valid certificate conformity to EN16630.