Andhra Pradesh State Irrigation Development Corporation Limited Tender

− do − for well steining

Bailing out of water for earth work excavation, cement concrete for PCC, RCC raft and steining below Low Water Level, inlcuing cost, conveyance of all materials hire charges of T & P etc for finished item of work to a depth of 1.00m to 2.00m

Providing High Yeild Strength Deformed steel bars (Fe 415 grade as per IS 1786-1979) of different diameters, including labour charges for cutting, bending to required sizes and shapes, placing in position with cover blocks of approved size and tying with binding wire of 20 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars and binding wire from approved sources to site of work, cover blocks and all incidental, operational labour charges etc., complete for finished item of work

Supply and fixing of ISMB 200x100x5.7mm girders including cost of all materials, labour and fabrication charges etc., complete as directed by the Engineer-in-charge

Fabrication and supply and erection of MS Trash rack of size 1.20x1.20 m with frame angle 75x75x6 mm and 16mm dia rods at 100 mm c/c on both ways with holding angulars of 75x75x6mm hold fasts etc. for trash rack including cost of all materials, all labour charges ,painting etc for finished item of work

MS Pipes & Specials :- Manufacturing, supply, erection and testing of MS Pipe & Specials with MS Sheet of 4/6/8/10/16/22 mm as required including cost of MS Sheet for pipes, MS plate of required thickness for flanges as per ISI, cutting, bending, rolling, welding, fabrication including transportation to site, bolts and nuts, rubber packing, painting with one coat of red oxide and including cost and conveyance of all materials, labour charges, etc., complete

ELECTRICAL AND MECHANICAL WORKS: Supply and erecting ISI open well submersible pumpset suitable for erection in open well with water resistant dynamically balanced impeller with stainless steel shaft sleeves, pump coupling and pivot with squirrel cage Induction Motor of 3 phase, 415V, 50Hz.., A.C.Supply, heavy copper windings with water proof insulation and high precision strength not to be effected by chemicals in water with suitable bronze bearings, 5 HP pump capable of discharging 0.26 Cusecs/ 7.36 LPS with a total pumping head of 25.00 ft/ 7.62 mtrs, erected with necessary H-type clamps of suitable size and strength including cost of all materials, Transportation and labour charges etc., complete. Makes Kirloskar/ Crompton/Texmo/CRI/KSB/Lubi/PSG/ AryenVarsha

Fabricaiton, tranportation and supply of wall mounted control panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated, painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all intenral wiring using L&T/Finolex copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump set. i) Voltmeter: 0-500 V 96x96mm size. Makes:L&T/C&S/SALZAR/HPL/AEI/Meco/Rishab-1 No SALZAR/HPL/AEI/Meco/Rishab - 1No. ii)0 to 20 Amps / 0 50 Amps Ammeter (96x96xmm size). Makes: L&T/C&S/SALZAR/HPL/AEI/Meco/Rishab - 1No. iii) Single phase preventor of suitable range Makes: L&T/Minilec/Powertec. -1No iv) 32 A TP, 10KA MCB. Makes: Legrand/Schneider - 1No. v) Indication lamps (R-Y-B) with swich control - 1 set vi) Voltmeter & Ammeter selector switch - 2Nos vii) Supply and fixing of ISI Mark suitable capacitors. Makes: L&T/ Siemenrs. Schneider/Epcos/Havells. viii) Up to 7.5 HP with DOC Starter of make C & S Crompton/ L&T/Siemens/BCH

Supply of 3 Core, 2.5 Sqmm copper cable

Supply and fixing of 80mm dia B class GI Pipe

Supply and erection of 80 mm dia PN 10 DI D/F Gate Valve(Soft seated) Resilient seated soft sealin gate valve(Sluice valve) with body bonnet of ductile iron of grade GGG40/ SG 400/12 or quivalent grade as per IS 3896 part2-1985 and subsequent revisions, wedge fully rubber lines EPDM food grade quality and seals of NBR and the valves should be of vaccum tight and 100% leak proof with face to face dimensions as per BS5163-89/IS14846-2000/DIN 3202 F 4. The valve should be with electrostatic powder coating bith inside and outside pocket less body passage. Drilled as per IS:1538 complete

Supply and fixing of 80mm G I Bends

Supply and fixing of 80mm G I Tee

Supply and fixing of 80mm G I Couplings

Supply and fixing of 80mm G I Flanges

Supply and fixing of 75mm PVC Tee

Supply and fixing of 75mm PVC Threaded Coupler

Supply and fixing of 75mm PVC Couplings

Labour charges for fixing of the specials G I & PVC includng cost of bolts, nuts, washers etc

TOTAL