Andhra Pradesh Education And Welfare Infrastructure Development Corporation Tender

Supply and fixing of MS Grills using required Structural steel such as MS Angular, Channels, Tees, Flats, etc.., including cost and conveyance of all materials and all labour charges for cutting, welding, jointing in place in position etc.., complete for finished item of work

Plain Cement Concrete corresponding to M5 grade as per IS 456 equivalent to (1:5:10) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 20mm size Hard Blasted Granite graded metal (IS383, 1970) from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work for Dummy Columns (APSS No. 402)

Providing & placing of terrance ( at all floor) polytech water storate tank with double layer approved brand & manufacture with cover and suitable locking arrangements and making necessary holes for inlet andoutlet and over flow pipe wigth out fittings and base supports for tank including cost and conveyance of all materials and all labour charges etc., complete work for finished item of work

Plain Cement Concrete corresponding to M5 grade as per IS 456 equivalent to (1:5:10) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 40mm size Hard Blasted Granite (IS383, 1970) metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work for Foundations and Flooring Bed (APSS No. 402)

Plastering 12mm thick in CM (1:5) with single coat dubara sponge finish including cost and conveyance of all materials like cement, sand, water etc., to site, seigniorage charges, sales & other taxes on all materials,all operational, incidental and labour charges such as mixing mortar, scaffolding charges, lift charges, including cutting of Grooves wherever necessary as directed by Engineer -in- charge, finishing, curing, etc., complete for finished item of work. (APSS 901,903 & 904)

Brick Masonry in superstructure with CM (1:8) prop: using second class bricks from approved source having minimum crushing strength of 40 Kg/Sqcm. including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental and labour charges such as mixing cement mortar, constructing masonry, scaffolding charges, lift charges, curing, etc., complete for finished item of work for Second Floor. (APSS No. 501 & 504).

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size 45x75 MM. The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM.

Providing and fixing of 28-30mm thick solid wood polymer Composite (WPC) single extruded door shutter with 3mm top and bottom rigid layer with an over all density of 750kg / Cum. It will be fixed to the frame using 3 Nos.of 100mm long MS butt hinges, 1 No.of 150mm long MS tower bolts, 1 No.of 200 mm long MS aldrop and 2 Nos.of 125 mm long MS handle for fixing the door with frame including cost and conveyance of all materials and all labour charges etc.., complete for finished item of work.

Supply and fixing of Orssia pan of size 580x440mm white glazed WC 1st quality ISI make parry, Neycer & Hinduwere make conformeding IS 2556-part 3-1981 with P and S trap with brick masonry seat including cost and conveyance of all materials and all labour charges etc.., complete for fhinished item of work

Supply, installation and commissioning approved make floormounted close coupled EWC suit CASCADE model 'P' or 'S' trip with dual flush procelain cisten fixed on EWC with all internal parts of dual flush cistern, ultra solid seat cover of approved make with rudder bufferand cap 15 mm angle stop cock 450mm long PVC interconnection pipee wall flanges all of approved make etc.., complete for finished item work in all respects: Special colour - Grade-III including cost and conveyance of all materials and all labour charges etc., complete work for finished item of work.

Supply and fixing NP Bib Taps of size 12.70mm dia of Indian make Seiko or equivalent including cost and conveyacne of all materials and all labour charges etc., complete for finished item of work.for 300 grams

Supply and fixing of 75mm PVC / SWR pipe 4kgs/cm2 including cost and conveyance of all materials and all labour charges etc., complete work for finished item of wrok

Supply and fixing of 20-24W, not less than 1100mm length LED batten light with extruded aluminum housing and polycarbonate cover, input voltage AC 220 - 260 Volts, with high power LEDs, having System Efficacy of =100 lumens/watt , PF0.9, Surge protection: 2KV, THD15%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI70, etc., complete with earth connection and not less than two years warranty.

Supply of 1200 mm (48" ) sweep 230V AC 50Hz High Speed ceiling fan with thee blades and doub le ball bearing croption make with all standard accessories etc., including cost and conveyance of all materials andall lablur charges etc., complete

Supply of Electronic step type modular regulator for ceiling fans 1200mm sweep complete erected on existing board including and giving connections complete including all lablur charges etc., complete for finished item of work.

Labour charges for fixing of ceiling fan and regulator including transportation and giving connections with twin core wire etc.., complete

Providing & Fixing of Openable Windows with Fly-mesh made of pre- painted steel (Base Steel as per IS 513 of 0.58 mm thick galvanized as per IS 277 with zinc of 150 GSM) primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer and the section for outer frame of 72 x 55mm, centre mullion of 72 x 50mm, section for fixed glass beading section of 12 x 12 mm and section for shutters of 48 x 25 mm and outer frame & mullion sections with rebate for glazed shutters, fly mesh and a 20 mm provision for guard bars/grills and fly mesh shutter section of 20 x 40 mm and the sections cut to length metre joined with corner bracket, centre mullions fixed with mullion cap, stay, handles, latch 2 Nos of heavy duty stainless steel pivot hinges per shutter and panelled with 5mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade), fitted using rubber gaskets including fixing the windows in the concrete/masonry wall by means of self expanding screws, including 10mm Square guard bars with 6” (152.4mm) pitch, complete for finished item of work Centre fixed both side openable shutter window 5’0”x4’0” (1524mm x1219.2mm). Outer frame section size of 72x50mm. Shutter frame section size of 48 x 25 mm. Mullion section size of 72x50mm. Fixed beading section size of 12 x 12 mm.

Providing and fixing door frames fabricated from sections made of galvanized steel powder coated (base steel as per IS 513, galvanised as per IS 277 with zinc of 120 grams / square metre), the factory made section are powder coated with pure polyester powder of 50-60 microns thick with total coated thickness of 1.25 mm, size of door frame section is of 105 x 60 mm with a rebate of 38 mm to accommodate 35 mm thick door shutter, with groove to insert gasket in the frame section, frame section filled with polyurethane foam, cut to length, and joined by way of welding, each frame provided with: a) 2mm thick MS powder coated butt hinges of 100 mm long – 3 Nos. for single shutter, 6 Nos. for double shutter. b) CRCA electroplates stiffeners of 6 Nos. – 3 in each vertical. c) 40 mm x 200 mm x 1.2 mm hold fasts screwed to stiffeners – 6 Nos. with split end tail. d) Nylon Aldrop Receiver – 1 No. for single shutter frame. e)Tie Rod – 1 No including cost and conveyance of all materials and all labour charges etc.., complete for finished item of work

Supply and Fixing of flush Door Double shutters of shutter size 0.56x1.95mtrs using 35mm thick flush door shutters of Solid Bond Wood block board type with teak ply on both faces including cost and conveyance of all materials and fixtures such as 6 Nos.of 125mm lng MS Butt hinges, 2 nos.of 200mm long Aluminium tower bolts, 1 No.of 300mm long Aluminium aldrop, 2 Nos.of 150mm Aluminium handles and 2 Nos.of MS Door Stoppers including cost and convenyance of all materials to site all Labour charges for shutter Fixing in position, with Hardware fixtures etc., complete for finsihed item of work.

Supply, Manufacturing and Fixing of Aluminium anodized fly proof mesh door single shutter to existing door frame using alround and middle horizontal sectin frame of size 44.70x18.50 x1.20mm thick and fixed to frame with required 0.20mm thick (304 guage) SS PC black mesh and binding with required EPDM mesh Gasket (beading) including cost and conveyance of all materials and fixtures such as 4Nos., of special grade PC hinges, 2Nos., of 150mm long aluminium tower bolts, 2Nos., of 100mm long aluminium handles and 2Nos., of Magnetic catches with required screws and specials like joint clips including cost and conveyance of all materials and all labour charges for fixing in position as directed by the departmental officers etc., complete for finished item of work.

Supply, Manufacturing and Fixing of Aluminium anodized fly proof mesh window shutter to existing window frame using alround and middle horizontal section frame of size 20.90x9.45 x0.86mm thick and fixed to frame with required 0.20mm thick (304 guage) SS PC black mesh and binding with required EPDM mesh Gasket (beading) including cost and conveyance of all materials and fixtures such as 2Nos., of special grade PC hinges, 1No. of 75mm long aluminium tower bolt, 1No., of 100mm long aluminium handle and 1No., of Magnetic catche with required screws and specials like joint clips including cost and conveyance of all materials and all labour charges for fixing in position as directed by the departmental officers etc., complete for finished item of work.