Andhra Pradesh Education And Welfare Infrastructure Development Corporation Tender

Plain Cement Concrete corresponding to M7.5 grade as per IS 456 equivalent to (1:4:8) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 40mm size Hard Blasted Granite (IS383, 1970) metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work for Foundations (APSS No. 402)

Plain Cement Concrete corresponding to M15 grade as per IS 456 equivalent to (1:2:4) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 20mm size Hard Blasted Granite (IS383, 1970) Machine Crushed graded metal from approved quarry including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental and labour charges such as mixing, laying, curing concrete, etc., complete for finished item of work (APSS No. 402)

Brick Masonry in superstructure with CM (1:8) prop: using Fly ASH Bricks of size 290x225x140mm with compressive of 50 Kgs / Sqcm from approved source including cost and conveyance of all materials like cement, sand, fly ash bricks, water etc., to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental and labour charges such as mixing cement mortar, constructing masonry, scaffolding charges, lift charges, curing, etc., complete for finished item of work. (APSS No. 501 & 504).

Reinforced cement concrete with M 25 grade Design mix ( by weigh batching ) using 20mm size (SS 5) machine crushed hard blasted granite graded metal (coarse aggregate) from approved quarry using a minimum quantity of 380 Kg of cement per 1 Cum of concrete including cost and conveyance of all materials like cement, fine aggregate (sand) ,coarse aggregate, water etc. to site and cost of seigniorage charges on all materials including centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates, etc.,, shuttering, machine mixing, laying concrete, 7.5cm thick at fixed end and 5cm thick at free end with an average thickness of 6.25cm including labour charges for mixing, laying, curing etc., complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402 & 403) for platforms of 75mm thick

Plastering 12mm thick in two coats with base coat of 8mm thick in CM (1:6) and top coat of 4mm thick in CM (1:4) dubara sponge finish including cost and conveyance of all materials like cement, sand, water etc., to site, seigniorage charges, sales & other taxes on all materials,all operational, incidental and labour charges such as mixing mortar, scaffolding charges, lift charges, including cutting of Grooves wherever necessary as directed by Engineer - in - charge, finishing, curing, etc., complete for Even Surfaces of Wall for finished item of work. (APSS 901,903 & 904)

Supply and fixing powder coated aluminium fully Prelaminited Partical board Door of size 1.05 x 2.10 as per the using aluminium sections of 45 mm x 45mm , 1.50 mm thick for Outer frame allround, and Center Fixed panels frame of size 45mm x 45mm ,1.50 mm thick , Bottom 12 mm thick Pre laminated Partical board , top fixed with 5mm thick Tinted - Bronze/ Green Glass fitted with suitable aluminium glazing clips and fixtures Aluminium handle 125 mm 1 no , Aluminium hinges 125mm 3 Nos including labour charges for manufacturing Door, fixing in position with all required necessary accessories like screws, filling gaps with silicon sealant etc., including overheads & contractors profit complete for finished item of work. (The Aluminium section used shall be standard make confirming to IS 1948 – 1961) and as approved by the Engineer) (1.05 x 2.10 )

Supply installation Testing and commissioning of 2.0 KVA , 72/96VDC KVA on line UPS system confirms to IS 16242(Part-I):2014 and IEC 60240-1 : 2008 with IGBT technology pure sine wave out put, double conversion with auto and manual static by pass switch single phase input / Single phase output. Makes : As per list of recommended brands.

Supply and Fixing MS Purlins 80 x 80x 4mm dia including Labour Charges for fixing complete including cost and conveyance of all materials to site, sales and other taxes, all labour charges etc., complete for finished item of work

Supply and Fixing MS Purlins 40 x 40 X 3mm dia including Labour Charges for fixing complete including cost and conveyance of all materials to site, sales and other taxes, all labour charges etc., complete for finished item of work

Supply & fixing pre-painted galvalium trepizoidal profile roofing sheets with 0.47mm thickness,coating Alu-zinc coating AZ 150 GSM. Tensile strength : 550 MPA,paint coating : Regular modified polyster painting. Thickness (top) 18-20 microns,(bottom) 5-7microns including C/C of all materials like sheets, J bolts, bitumen washers etc. with or wothout ridge with sales & all other taxes & all labour charges etc. complete for fixing sheets in position.

Painting to New Iron work with two coats of ready mixed Synthetic Enamel paints in all shades Grade - I having VOC (Volatile Organic Compound ) content less than 50 grams/ liter over an existing steel primer including cost and conveyance of all materials to site, sales & other taxes, incidental, operational and all labour charges etc., complete for finished item of work. (APSS No. 1201, 1207 & 1212).in All Floors

Supply, transportation and fixing of 36W Recessed / Surface mounting 2' x 2' (600x600 mm) LED luminaire made of CRCA sheet housing with powder coated with acrylic diffuser, Constant current Driver as per IS: 15885 (Part 2/ Sec 13) : 2012 , With System lumen output ≥ 3200lm operating voltage range of 150 to 265 Volts AC, P.F 0.9, Surge protection: 2KV, THD10%, with high power LED's having efficacy of 120 lumins / watt, CCT: 3000K - 5700K, minimum CRI70, .etc.,, complete. a) LUMINAIRE MAKE : Phillips /Lighting Technologies(LT) / GE-Venture / Crompton / Wipro / Bajaj / Havells / VIN /Halonix/Jaquar/HPL b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG.

Supply, Fixing and Transportation of 18W/20W, 1100mm length LED batten light with extruded alluminium housing and polycarbonate cover, input voltage AC 220 - 260 Volts with PF0.9, Surge protection: 2KV,THD15%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI70, .etc., complete. with Fixing of 18W/20W LED luminaire on wall / Ceiling with / TW round blocks with all accessories including giving connections and all labour charges etc., complete. Makes: Surya / Pharox / Halonix / HPL / Greenlights / Fortune Art / Capart / GM / Goldmedal / Syska / Cosmo / Trinic b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / EVERLIGHT/ San'an

Supply of 12" (300mm) ISI, 900 RPM Heavy duty exhaust fan with metallic blades with Mark.Makes: Crompton / Almounard / Havells Ventil Air-DB

Labour charges for fixing of Exhaust fan in wall with necessary connections and masonary work of making hole, finishing etc., complete

Supplying and fixing of SWR/ PVC pipes (as per ISI standards) 4 Kg/Sq.cm. Prince/sudhakar or any ISI brand and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with PVC clamps if necessary with required number of Bombay nails including cost and conveyance of all materials to site, labour charges etc.complete for finished item of work at all floor levels. (APSS No. 1302 1319 & 1326) 160mm dia 3 Mts single socket

Supplying and fixing NP bib taps of size 12.70mm dia of Indian make Seiko or equivalent including cost and conveyance of all materials, labour charges etc., complete for finished item of work in all floors. For 4

Supply of 48" (1200mm) Sweep ISI mark Ceiling Fan as per IS 374 - 1979 and, with double ball bearings, power input not more than 50W , air delivery more than 200 cubic meter/min but without Regulator. Makes : Crompton / Bajaj Kassels 50 / Usha atom

Supply of Modular type Electronic fan regulator hum free step type socket size in the existing switch board.

Labour charges for fixing of ceiling fan with regulator including transportation, 3 core wire leads etc complete