Public Works Department Tender
To inquire about any e-tender the Andaman & Nicobar Islands government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder one can find every eprocurement Punjab tender on BidAssist. BidAassist has collated each and every Eproc Andaman & Nicobar Island Tender on its website. Looking for Andaman & Nicobar Island tenders online or going through the cumbersome government websites for it, has been made easier with the help of BidAssist.
Public Works Department - PWD Tender
Software and IT Solutions
Education And Training Services
Eprocure
Opening Date26 Jun 2024
Closing Date22 Jul 2024
Tender Amount₹ 25,66,127
Costs
EMD
₹ 51,323Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_APWD_14562_1Bid Award Id
ViewTender No
NIT No. 12/EE/PBND/2024-25Tender Authority
Public Works Department ViewPurchaser Address
-Website
http://http://apwd.and.nic.in/APWD/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Of area 3 sq. metres and below
14
-
-
Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:
-
-
-
Asbestos Cement sheet
180
-
-
Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead :
-
-
-
Of sectional area 40 square centimetres and above
0.66
-
-
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
-
-
-
All kinds of soil.
23.76
-
-
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :
-
-
-
Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole :
With Chlorpyriphos E.C. 20% with 1% concentration
62
-
-
Supplying chemical emulsion in sealed containers including delivery as specified.
-
-
-
Chlorpyriphos emulsifiable concentrate of 20%
10
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
-
-
-
1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
4.98
-
-
1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
11.11
-
-
Centering and shuttering including strutting, propping etc. and removal of form work for:
-
-
-
Foundations, footings, bases for columns
62.72
-
-
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
29.6
-
-
Centering and shuttering including strutting, propping etc. and removal of form for
-
-
-
Lintels, beams, plinth beams, girders, bressumers and cantilevers
36.5
-
-
Columns, Pillars, Piers, Abutments, Posts and Struts
18
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
-
-
-
Thermo-Mechanically Treated bars of grade Fe-500D or more.
534.36
-
-
Providing and laying Autoclaved Aerated concrete blocks (AAC) masonry 150mm/230mm/300 mm thick AAC with Grade-1 blocks of density 551-650 kg/cum conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).
7.59
-
-
Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.
1
-
-
Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :
-
-
-
250x16 mm
3
-
-
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :
-
-
-
200x10 mm
6
-
-
100x10 mm
24
-
-
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :
-
-
-
125 mm
6
-
-
75 mm
15
-
-
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
-
-
-
Single rubber stopper
3
-
-
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.
-
-
-
Fixed to openings /wooden frames with rawl plugs screws etc.
190.97
-
-
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
255.29
-
-
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
-
-
-
Electric resistance or induction butt welded tubes
1020.88
-
-
Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.
12
-
-
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.
-
-
-
110 mm diameter
39
-
-
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
-
-
-
Coupler
110 mm
3
-
-
Bend 87.5°
110 mm bend
12
-
-
Single tee with door
110x110x110 mm
2
-
-
Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete.
-
-
-
110 mm
28
-
-
12 mm cement plaster of mix :
-
-
-
1:4 (1 cement: 4 fine sand)
120
-
-
12 mm cement plaster finished with a floating coat of neat cement of mix :
-
-
-
1:3 (1 cement: 3 fine sand)
87.88
-
-
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.
-
-
-
40 mm thick with 20 mm nominal size stone aggregate
28.16
-
-
Finishing walls with Acrylic Smooth exterior paint of required shade .
-
-
-
New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm
173.3
-
-
Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.
-
-
-
With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 60 grams/ litre
29.66
-
-
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
-
-
-
Two or more coats on new work
94.5
-
-
Painting with oil type wood preservative of approved brand and manufacture:
-
-
-
Old work (one or more coats)
120
-
-
Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.
-
-
-
80x1.20 mm M.S. laths with 1.20 mm thick top cover
8.1
-
-
Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade.
-
-
-
One or more coats on old work.
323.61
-
-
Finishing walls with Acrylic Smooth exterior paint of required shade:
-
-
-
Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface
174.35
-
-
Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.
51.77
-
-
Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I.staples, turn buckles etc. complete. (Cost of posts, struts, earthwork and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used.
-
-
-
With G.I. barbed wire
244
-
-
Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete.
-
-
-
10 litre (full flush) capacity-white
2
-
-
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
-
-
-
Flexible pipe
32 mm dia
2
-
-
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
-
-
-
White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap
2
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work
-
-
-
25 mm nominal dia Pipes
50
-
-
40 mm nominal dia Pipes
86.4
-
-
Providing and fixing uplasticised PVC connection pipe with brass unions :
-
-
-
45 cm length
15 mm nominal bore
4
-
-
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
12000
-
-
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :
-
-
-
15 mm nominal bore
2
-
-
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931
-
-
-
15mm nominal bore
4
-
-
Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in- charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).
164
-
-
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).
-
-
-
Superior hardwood Cart-II (A)
0.22
-
-
Providing wood work in frames , trusses, purlins, rafters etc sawn and put up in position with Superior hard wood Cat-II (A)
0.64
-
-
Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes including stainless steel butt hinges with necessary screws.
-
-
-
35mm thick Superior hardwood cat-II (A)
9.57
-
-
Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including stainless steel butt hinges with necessary screws excluding, panelling which will be paid for separately.
-
-
-
Superior hardwood cat-II (A)
35mm thick shutters
5.25
-
-
Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :
-
-
-
25mm thick Superior hardwood cat-II(A)
4
-
-
Providing and fixing curtain rods of 1.25 mm thick stainless steel with two stainless steel brackets fixed with brass screws and wooden plugs, etc., wherever necessary complete :
-
-
-
20mm diameter (Heavy type)
9.6
-
-
Providing 25x5 mm flat iron hold fast 10 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)
27
-
-
Providing and fixing pre-painted galvalume (PPGL) steel profile sheets AZ-150 of brand of Tata blue scope Steel/Everest Industries Limited, JSW Steel Limited, Jindal India Limited or or equivalent (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm + 0.05 %, total coated thickness with aluminium zinc coating 150 gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws (Xylan) of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
257
-
-
Providing and fixing Pre-Painted galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Blue Scope stee, Everest industries Ltd, JSW Steel Ltd, Jindal Steel Ltd or equivalent make roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete
-
-
-
Ridges Plain (500-600mm)
20
-
-
Gutter (600mm over all girth)
20
-
-
Extra for providing and fixing wind ties of 40x6mm flat aluminium section
100
-
-
Providing and fixing soil, waste and vent pipes
-
-
-
100mm dia PVC pipe
30
-
-
75mm dia PVC pipe
6
-
-
Providing and fixing PVC plain bend of required degre.
-
-
-
100mm dia
5
-
-
75mm dia
6
-
-
Providing and fixing PVC single equal plain junction of required degree etc complete.
-
-
-
100x100x100mm
2
-
-
75x75x75mm
2
-
-
Supplying, installation and commissioning of 1.5 HP capacity electrical (motar) pump (kirloskar Model No. KDS-1.525+Por equivalent make) with necessary accessories etc complete as per the direction of Engineer-in-charge (suction 50mm and delivery 40mm).
2
-
-
Providing and fixing CPVC extension nipple for polythylene water tank pipe fittings of approved quality.
-
-
-
25mm nominal bore
3
-
-
Construction of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 grade stone aggregate 20mm nominal bore) manhole, R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design :
-
-
-
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
2
-
-
Providing cement concrete surface drain including earthwork excavation 10 cm thick base concrete and 15 cm thick side wall with 1:3:6 ( 1 cement : 3 Coarse sand: 6 graded stone aggregate of 40 mm nominal size) cement concrete finished with 1:4 (1 cement : 4 sand) a floating coat of neat cement inside the drain and its top and exposed surface including earthwork in excavation and disposed of surplus earth etc.
-
-
-
23 X 23cm surface drain.
30
-
-
Providing and fixing E-Board sheet ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately):
-
-
-
6mm thick
55.37
-
-
Providing and fixing in position eaves or facia board with 18mm thick WPC board of approved quality and 30cm wide including nailing etc complete as per the direction of Engineer-in-charge.
105
-
-
Providing and fixing CPVC gate valve of approved quality (screwed end).
-
-
-
40mm nominal bore
2
-
-
25mm nominal bore
2
-
-
Providing and fixing PVC bend of required degree with access door of approved quality.
-
-
-
100 mm dia
1
-
-
75mm dia
2
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
-
-
-
1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)
6.24
-
-
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
102.28
-
-
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.
2
-
-
Providing, mixing and applying SBR polymer of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt, of cement used) as per specifications and directions of Engineer-in-charge. Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
-
-
-
12 mm average thickness.
105.18
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements