Indian Army Tender

Book case steel large , Book case steel large DIMENSION Over all size shall be of 840 mm long, 310 mm wide and 1675 mm high . DESCRIPTION All sheet shall be mild steel sheet 1 mm thick, back, sides, bottom, top and shelves.The book case shall be provided with four compartments of equal size. The shutters of each compartment shall open towards top and slide into the depth of the book case.Transparent glass 4mm thick shall be provided to front shutters. Two steel handles of 100 mm long shall be provided to each shutter of the compartment. The locking device shall be provided to each compartment with duplicate key and each shutter shall be provided with decorative key plate . FINISH All steel surfaces internally and externally shall be painted with two coats of silver hammer paint over a coat of primer with spray machine after preparation of surfaces. A mark of MES shall also be provided on top shutter of visible colour as directed by Engr-in -Charge.

Book shelf open large , Book shelf open large All as shown on drawing. Overall size shall be 915mm long 305mm wide and 1905 mm high sides and back shall be covered with 1 mm thick mild steel sheet. Slotted angle 25mm x 25mm x 3mm shall be provided at front and back as shown on drawing. 3mm thick corners of 75mm x 75mm shall be fixed at front and back to the top and bottom of shelves. seven sheves including top and bottom shall provided equall to make six compartments. all steel and iron surfaces shall be painted with two coats of enamel aint over a coat of primer after preparation of steel surfaces as directed by Engr in charge. welding shall be done as per the trade practice and as directed by the Engineer in charge.

Charpoy IP with hard top , Charpoy IP with hard top Overall size shall be 1980mm long, 900mm wide and 440mm high. Two long rails and two short rails shall be of 25mmx65mmx16 gauge MS rectangular pipe .The legs shall be of size 32mmx32mmx16 gauge welded to long and short rails as shown on drg.Two stiffeners of size 25mmx25mmx16 gauge shall be provided in equidistant between two opposite long rails. Six number cleat of size 25mmx60mmx6mm shall be welded with frame to support ply. Two stiffeners joining legs of size 25mmx25mmx16 gauge shall be provided at 150mm from ground level .12mm thick commercial plywood shall be provided for top as shown on drg with proper nut and bolt .one nut and bolt shall also be provided at centre of each stiffeners for fixing the plywood irrespective of what is shown on drg..PVC hard rubber shoes shall be fixed at bottom of each leg. All steel surfaces shall be painted with synthetic enamel black in color before applying a coat of primer. Rest all as per drg

Chair CB without Arms Steel , Chair CB without Arms Steel Overall size shall be 535mm wide 560mm deep and 900mm high. Seat shall be 455mm high from floor. Conduit pipe used for frame shall be 20mm dia steel tubing having wall thickness 1.6mm Welding of frame where required shall be as directed by GE or BSO and in running welding grinded to give smooth surface.The seat and back frame of the chair shall be made up of quality sheesham wood in natural polish with polythene cane in godrej pattern confirming to IS 5378 94 Type I of durable qualty .The wooden seat frame shall be further supported by steel strips measuring 19mm x 3mm at the front and the rear and each strip shall be welded to ERW frame. Cane shall be 2mm wide and 0.4mm thick Gola type weighing not less than 6 gms 10 RM. Bottom of legs shall have hard rubber shoes. The seat and back shall be fixed by providing suitable nut bolts and washer. Painting shall be done with spray machine after preparation of wooden surfaces. All iron surfaces exposed to direct view Shall be painted with two coats of enamel grey paint over a coat of primer after preparation of steel surfaces

Chair Computer , Chair Computer The Base pedestal assembly of chair computer shall be of dia 700mm and 1060mm high .The pedestal assembly shall be provided with injection molded in black 30% glass filled nylon. A 10.5mm dia forged bright Zinc plated MS Castor Pin is of press fitted into each prong for holding the castors. The seat and back of the chair computer shall be made of 12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping allround.The back rest shall be adjustable and consist of drop lift mechanism and shall be adjusted in the insert .It shall be scratch and weather resistant. Rest all as per drg.and as per sample approved by BSO or GE

Chair Dinning , Chair Dinning Chair Dining with Seat cushioned shall be made to the shape size and design as shown on drg as specified in particular specification and shall be manufactured in accordance with relevant IS. All wood work shall be of kiln seasoned and chemically pressure treated Ist class hard wood Teakwood. Seat shall be 75mm thick of polyurethane foam density of 32 KgCu.m covered with fabric of acrylic or polyester or polypropylene and upholstered with good quality leatherised of make Sleep well Kurl on Coir foam as approved by GE. Plywood for seat shall be 12mm thick melamine faced prelaminated particle board bonded with phenol formaldehyde as per IS 3087 1985 exterior grade BWR type and shall be ISI marking on the edges. Exposed edges of board shall be covered with 4mm thick teak wood edging and shall be fixed as specified and directed. Toes Nylon buffers shall be of best quality as approved by GE and shall be provided under each leg and fixed with 25mm long steel screws of suitable size. Finishes All wooden surfaces exposed to view except under sides of frame and bottom of legs shall be French polished. All other items or fittings shall be as shown on drawing and provided as per relevant IS and trade engineering norms or pattern.

Chair Writing , Chair Writing The frame of the chair shall be of MS tubular frame powder coated ,cantilever type of size 25mmx10mm in section. Back form shall be designed with contoured lumber support for extra comfort.120mm thick hot pressed plywood upholstered with superior quality fabric and moulded polyurethane foam with PVC lipping alround shall be provided at seat and back.PU arms shall be of superior quality and reinforced with MS insert.It shall be scratch and wheather resistant..Steel portion of chair shall be painted with two coats of synthetic enamel paint of black colour over a coat of primer.Rest all specifications are as per drg and directed by Engr-In-Charge

Chair Easy FD , Chair Easy FD DIMENSION Overall size shall be 510 mm long, 575mm wide and 720mm high . DESCRIPTION All wood shall be first class teak (MP). Front legs shall be 30mmx55mm in section and 355mm high up to seat level. Rear legs shall be of 30mmx55mm in section and 300mm high up to seat level and slanting 50mm away from vertical. Front, back and side rails of seat shall be out of 30mmx55mm in section and made to shape as shown on drawing. front, back and side rails shall join the front and rear legs at 355mm high and 300mm high in rear Teak wood arm rests shall be provided at 150mm above seat level and shall be of 30mmx55mm in section as shown on drawing. Back rest shall be made of frame consisting of top horizontal rail of 30mmx100mm in section out of 60mmx100mm teak wood made to shape as shown on drawing and lower horizontal rail of back rest shall be of 30mmx100mm in section joined together by vertical side rails of 30mmx25mm in section teak wood to form the frame Caning shall be done with plastic cane of 2mm wide and 0.4mm thick half round gola type weighing not less than 6gms in ten running meters. Caning shall be done in Godrej pattern. PVC shoes 25mmx25mm shall be provided at the bottom of all legs. All wood surfaces exposed to view when placed in position shall be given high gloss French polish with lacquer finish.

Chair Ornate with arms , Chair Ornate with arms As per Trade patern and directed by Enginer-in-Charge.

Chair verandah , Chair verandah The overall size of the chair shall be 455mm wide 455mm deep and 940mm high. The frame of the chair shall be of 19mm dia MS tube of wall thickness 1.6mm duly powder coated. The seat and back of the chair shall be of PVC 4mm of weight not less than 1.85 kgs and grooves 90x10mm ten in nos on seat and back. One stiffener 19mm dia MS tube shall be provided in between the front legs as shown in drg. An additional support in seat and back shall be provided at centre between the seat and back duly welded for rest of PVC seat irrespective of what is shown on drg. Rubber shoes of best quality shall be provided to each end of legs.Rest all as per drg.

Hat stand with mirror , Hat stand with mirror Overall size shall be 1330 mm long, 710mm high. The inner frame shall be of 50mmx20mm teak wood battens six in nos .The back and front of frame shall be covered with 6mm thick commercial ply.The edges of the frame shall be covered with 6mmx35mm teak wood edging fixed alround the frame with headless nails and adhesive.Six brass pegs 120mm long shall be fixed over the wooden membrane with brass screws as shown in drg.5mm thick looking mirror of (saint gobian,Modiguard/Atul) shall be provided as shown on drg with beading alround . Mild steel key plate shall be provided at both top corners of the hat stand. All teak wood surfaces shall be given high gloss French polish with lacquer finish. All steel surfaces shall be painted with two coats of enamel paint over a coat of primer. Rest all as per drgs

Ladder Alumium , Ladder Alumium Overall size shall be of 2310mm long and 363.5mm wide. The ladder shall be of Aluminium having wall thickness 3.18mm .Each rung shall be of 23mm dia aluminium pipe with wall thickness not less than 2.43mm and shall be eight in nos at equidistant space of 300mm in between as shown in drg.The stringer of ladder shall be 31.75mm wide and 3.18mm thick .Each alumnium pipe rung of 23 mm dia shall be fitted inside the stringer with end bend to shape and each rung on both sides shall be provided with hard rubber cap. Hard rubber caps or shoes shall be fixed at the ends of aluminium rungs and stringers as shown on drawing with screws. Rest all as shown on drawing.

Peg Table , Peg Table Overall size shall be 450mm long 300mm wide and 380mm high. Legs shall be of teak wood of section 30mmx50mm.The legs shall be 362mm high.5mmx5mm in section groove shall be provided on the top of legs which shall be visible when placed in position.Two nos top rails of section 20mmx40mm of teak wood shall be provided connecting legs.Two bottom rails of size 20mmx40mm shall be fixed between the legs .A centre stiffeners of size 20x40mm shall be provided at centre of side bottom rails for extra support irrespective of what is shown on drg.Top of table shall be of 18mm thick prelaminated MDF board of approved shade.4mm thick teak wood beading shall be provided alround the top edges of table. FINISH All wood surfaces exposed to view when placed in position shall be french polished with high lacquer finish.Rest all as per drg.

Rack adjustable 6 tier steel , Rack adjustable 6 tier steel Overall size shall be 915mm long,610mm wide and 1905mm high.Four vertical angle iron of 40mmx40mmx4mm shall be provided at four corners..Top,Bottom ,sides ,Back,Shelves shall be of 1mm thick mild steel sheet.Five shelves equally spaced to make six equal compartments shall be provided of 1mm thick MS sheet.Four 75mmx75mmx3mm flat iron cut to shape to form angular brackets shall be provided on front side.All steel surfaces exposed to view shall be given two coats of enamel paint over a coat of primer with spray machine after preparation of surfaces. Rest all as per drgs.

Recepticle PVC , Recepticle PVC The body of receptacle PVC shall be made up of thick polymer plastic .It shall be of capacity 20 liters, provided with lid and handle as shown in drg.

Stool revolving , Stool revolving The Base pedestal assembly of chair computer shall be of dia 700mm and 1060mm high. The pedestal assembly shall be provided with injection molded in black 30% glass filled nylon. A 10.5mm dia forged bright Zinc plated MS Castor Pin is of press fitted into each prong for holding the castors. The seat and back of the chair computer shall be made of 12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping allround.The back rest shall be adjustable and consist of drop lift mechanism and shall be adjusted in the insert .It shall be scratch and weather resistant. Rest all as per drg.and as per sample approved by BSO or GE. Pre treated with epoxy powder coated oven baked with ivory white color or white or warm grey.

Table 3 feet x 2 feet with drawer , Table 3 feet x 2 feet with drawer All as shown on drawing. Overall size shall be 900mm long, 600mm wide and 760mm high. All wood shall be of first class hard wood teak (MP). Legs shall be 60mm x 30mm in section throughout and 741 mm high, four in numbers, Joined together in front, back and sides with top rails of 20mm x 110mm in section provided flush with top of legs. The left hand side portion, viewing from front shall have drawers of 300rnrn wide. 25mm x 40mm in section teak wood stiffener on one side and 20mm x 30mm in sectlon teak wood fillet on other side of drawer shall be provided as shown on drawing. Track rails 25mm x 25mm In section on one side and 30mm x 25mm in section on other side of drawers having rebate for guide rails as 12mm x 12mm in section shall be provided all as shown on drawing. The sides and back of drawer shall be of 12mm thick and 110 mm high teak wood planks. The front of drawer shall be of 20mm x 110mm in section teak wood plan. The bottom of drawer shall be of 6mm thick commercial plywood. Two bottom rails, one on each short side, shall be provided of 20mm x 60mm in section teak wood joining legs in short sides. The top shall be of 18mrn thick particle board commercial over which 1.5mm thick plastic laminated sheet shall be fixed, 4mm thick teak wood edging shall be- provided al-round-the top of table. The top of table shall be flush with legs and there shall be no projection on any sides. All wood surfaces exposed to view when placed in position shall be French polished with high gloss finish.

Table 3 feet x 2 feet without drawer , Table 3 feet x 2 feet without drawer All as shown on drawing. Overall size shall be 900mm long, 600mm wide and 760mm high. All wood shall be of first class hard wood leak (MP). Legs shall be of 60mm x 30mm in section throughout and 741 mm high, four in numbers joined together in front, back and sides with top rails 20mm x 60mm In section provided flush with top of legs. At bottom, 100mm high from bottom, side wooden lower rails of 20mm x 60mm in section shall be provided in short sides Joining legs in short sides. 5mm x 5mm in section groove shall be provided in legs at top of legs in portion visible 10 view when placed in position. table top shall be of 18 mm thick particle board commercial over which 1.5mm thick plastic laminated sheet shall be fixed with fevicol irrespective of what is shown on drawing. 4mm thick teak wood edging shall be provided all-round the edges of top of table. The top of table shall be flush with legs and there shall be on projection on any sides. All wood surfaces exposed to view when placed in position shall be French polished with high gloss finish. Hard rubber or PVC shoes of 25mm dia and 25mm high shall be screwed to bottom of all legs.

Table bed side , Table bed side (W) The overall size of the table bed side shall be 450mm x 450mm x 600mm from rear and 450mm x 450mm x 500mm from front as shown in drg.The entire frame of table bed side shall be made up of 18mm MS square pipe (18 Gauge) duly black powder coated. The two sides and top shall be made up of 18mm thick prelamainted particle board exterior grade. The Back of the table except the top portion as shown in drg shall be provided with 6mm commercial plywood BWR grade duly screwed to frame. The two sides, back and bottom of drawers of the table shall be made up of 12mm thick commercial plywood irrespective of what is shown on drg, except the front side which shall be of 18mm thick prelaminated particle board exterior grade. The drawers shall be made functional on teak wood runners fixed inside the tables shown on drg.The drawers of the tables shall be provided with 100mm long CP handles .Rest all as per drg.

Table dining 6 Person , Table dining 6 Person All as per drg, the wood shall be 1st class hard wood teak free from any joints cracks and knots. The top shall be made out of 18mm thick pre laminated particle board one side teak lamination in wange / teak (as approved) colour and one side white lamination. all exposed edges of PPB shall be provided wooden beading of teak wood 4mm thick x 18mm wide duly polished with matching colour The frame shall be polished after prepration of surfaces with two or more coats of brown / teak colour polish as per the requirement to its glossy look.

Table dressing gents with mirror , Table dressing gents with mirror All as per Drg, the frame shall be strictly as per drg and in wqange / teak colour as approved. The mirror shall be of 5mm thickness of best quality. The door leaf shall be fixed with continous piyno hingis of brass, 2x magnatick catchers shall be provided to catch and close the door leaf.

Table dressing ladies with mirror , Table dressing ladies with mirror The overall size of the table dressing shall be 1150mm long 380mm wide and 1700mm high. The sides, top ,back and front of the base unit shall be of 18mm thick prelaminated MDF board. The bottom of the side units shall be of 12mm thick commercial plywood. The sides and back drawers shall be of 12mm thick prelaminated MDF ,bottom of the drawers shall be of 6mm thick commercial ply whereas the front of the drawers shall be of 18mm thick prelaminated MDF board.5mm thick electro copper plated mirror shall be fixed over 6mm thick plywood back. The plywood shall be fixed on two vertical hardwood member of size 45mmx35mm .a horizontal support of size 30mmx20mm shall be provided in between two vertical members. The Overall size of the stool shall be 440mm long 350mm wide and 425mm high. The four sides shall be of 18mm thick prelaminated MDF .The top of the stool shall be of 12mm thick plywood openable as shown in drg.Four heavy duty revolving nylon double wheels shall be provided at base below the 6mm base ply fixed over wooden runner 20mmx20mm.The seat of the stool shall be 75mm high ,made of foam 40 density covered with tapestry cloth as approved by Engr-In-charge or GE.Rest all as per drg.

Table office clk steel , Table office clk steel DIMENSION Overall size shall be 1200mm long, 610mm wide and 760mm high. DESCRIPTION Steel frame shall be of size 1160x570x742mm .four legs of 25mm mild steel tube of 1.6mm wall thickness shall be provided. Top of legs shall be joined together with 25mm square mild steel tube of wall thickness 1.6mm in long and short sides. Two short stiffeners of same size shall be provided at 130mm from bottom of legs. One long stiffener shall also be provided to the middle of short stiffeners. Three drawers of equal size shall be provided on the right hand side above the stiffener at 130mm high with overall size of 350mm wide and 430mm high and 410mm deep..The top of table shall be provided with pre-laminated MDF board of 18/19mm thick with teak veener shade and 4mm thick teak wood edging alround the table .Hard rubber or PVC toes shall be provided to the legs.Locking device shall be provided to drawers. FINISH All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

Table office officer steel , Table office officer steel DIMENSION Over all size shall be of 1680x870 x760mm. DESCRIPTION 25 mm MS square tube 1.6 mm thick shall be provide to frame 1 mm thick MS sheet nominal all around for drawer.Top shall be of 18mm thick pre-laminated MDF board ISI mark (exterior gde) one side decorative finish approved by GE and 4 mm thick teak wood edging all around shall be provided for top.Three drawers shall be provided on right hand sides of table.A cupboard with front openable door shall be provided on the left side of the table.A shelf shall aslo be provided at the middle of cupbaord.All sheet for drawers shelf and cupboard and back covering shall be 1mm thick.Hard rubber shoes shall also be provided to the bottom of legs.Rest all as per drgs FINISH All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

Table writing Med , Table writing Med DIMENSION Overall size shall be 1145mm long, 600mm wide and 760mm high. DESCRIPTION All wood shall be of first class hard teak wood except top and right hand side drawer cabinet. Legs shall be of 35mmx55mm in section and 717mm high having 5mmx5mm in section groove at the top of legs at the portion when placed in position. The top shall be of 18mm thick prelaminated MDF board of approved shade and the edges shall be covered with 4mm thick teak wood beading. Two short stiffeners of teak wood of size 50mmx40mm in section irrespective of what is shown on drg shall be provided between legs at 100mm from bottom of legs. Sides of the box which house the drawer and cabinet shall be 18mm thick prelaminated particle board exterior grade. Sides and back of drawers shall be of 12mm thick teak wood planks. Bottom of drawers shall be of 6 mm thick plywood commercial.6mm thick plywood commercial 75mm high partition shall be provided in the drawer. Shutter for cabinet shall be fixed with piano type continuous hinges. Lock shall be provided to drawer and shutters. Recessed handle shall be provided to drawer and shutter.25mm dia and 25mm high rubber shoes shall be fixed to bottom of legs. FINISH All wood surfaces shall be French polished with high gloss finish. Rest all as per drg.

Teapoy wooden , Teapoy wooden DIMENSION The overall size shall be 600mm long, 450mm wide and 540mm high. DESCRIPTION The legs shall be 60mmx30mm in section and 497 mm high and shall be of teak wood.5mmx5mm in section groove shall be provided at the visible portion of top of legs. Top rails of teak wood of 20mmx50mm in section and 510mm long shall be provided between the legs. Bottom rail of teak wood of 20mmx50mm in section and 420mm long shall be provided between legs, widthwise at 100mm above the bottom of legs. A centre rail of size 20mmx50mm shall also be provided lengthwise at centre in between the side bottom rails irrespective of what is shown on drg.25mm thick and 25mm dia hard rubber /PVC rings shall be fixed to the bottom of all legs fixed with 30mm long screws.Top of table shall be of 18 mm thick pre-laminated MDF board with 4mm teak wood edging al-round the top of table. FINISH All wood surfaces shall be French polished with high gloss finish. Rest all as per drg

Sofa Set 4 seater , Sofa Set 4 seater all as per drg, the timber in all around shall be first class hard wood teak,The cushions shall be of min 40 D and covered with tapestery cloth of approved quality pattern and colour before incorporating in work The frame shall be polished after prepration of surfaces with two or more coats of brown or teak colour polish as per the requirement to its glossy look.