WAPCOS Limited Tender

od78975/2020_2021 : Isolator With Enclosure<br>Supply and fixing of FP CRCA sheet steel powder coated enclosure on surface/recess along with following Amps, 415V, DP/FP isolators confirming to IEC 60947-3 complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation.<br>40A FP Isolator with enclosure<br>

od79989/2020_2021 : END TERMINATION<br>Supply and making end termination with brass double compression gland, earth clip and aluminum lugs/ Cu lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminum conductor cable of 1.1kV Grade as reqiured.<br>4Cx300sq.mm Al Cable<br>

od63870/2020_2021 : <br>" Supply, Installation, Testing and Commissioning of factory built Ceiling Suspended Chilled water Double Skin horizontal Air handling units made of 40mm thick panels consisting of pre plasticized GI casing of thickness 0.8mm outside layer and inner layer shall be of 0.8mm plain GI sheet with polyurethane form(PUF) insulation factory injected between them by injection moulding machine with thermal break profile complete with fan section with backward curved plug fans suitable for static pressure as required with VFD drives , coil section with aluminium finned copper tubes (min. 10 fins per inch, tube thickness not less than 0.5mm),Cooling coil of 6 rows deep, filter section with 50mm thick metal viscous/washable synthetic type air prefilters (10 micron) & 5 micron fine filters, mixing box with fresh air & return air intakes with dampers,drain connections, SS drain pan(18G) with PUF insulation, TEFC sq.cage induction motor of efficiency class IE3 suitable for 415+-10% volts, 50 Hz, 3 phase AC supply including mounting and fixing arrangements, anti vibration springs/ isolator bearings etc complete as per specification and of following capacities.The cost shall be inclusive of VFD starter panel in a separate enclosure with necessary rating incomer isolator / MCCB /contactor with all accessories including necessary connections, inter connections and control wiring with pressure sensors (minimum 2 Nos.) for complete installation. Only HVAC application VFDs shall be used.<br>Horizontal Ceiling Suspended AHU 7.4 TR/ 2384 CFM/ 6 RD/ ESP -138 Pa

od253713/2021_2022 : Supply,Installation, testing and commissioning of smart water meter confirming to IS 4064(1) of multijet class B magnetic type 100mm meter battery powered with neccesary fittings such as threaded pieces, unions, check nuts complete as required. 100mm dia

od188785/2020_2021 : Supply, Installation, testing and commissioning of IR Fixed Dome Camera with below specifications as minimum and with all the necessary accessories for the installation<br> - 3.6 mm fixed lens<br> - 2MP Resolution<br> - H.264, MJPEG codec<br> - Edge Storage (Minimum 32GB)<br> - IR - 30 meters<br> - 120dB WDR<br> - IK10, IP66<br> - PoE

od178535/2020_2021 : Horizontal Bed Head Panels of 4 feet long with provision for 3 nos electrical (power & data) & min 5 nos Gas outlets - as per technical specification for beds<br>

TOKEN/QUEUE MANAGEMENT SYSTEM

od78169/2020_2021 : INDUSTRIAL SOCKETS<br>Supplying, installation, testing & commisioning following surface mounting insulated plug and socket arrangement, power socket in independent position housed in suitable enclosure with high ingress protection (IP 67) with DIN rail for providing RCBO protection of suitable rating , with safe entry for cable and straight plugs with instant locking with screwless clamping, with direct connection with universal screws all terminals facing the same direction with large body size making wiring easy, maximum safety with elongated earth pin disconnected last on removal with direct mounting onto base and maximum cable grip with screwless clamp giving necessary connection as required including all acessories as required for complete installation and as directed by engineer in charge/consultant, and making good any damages made during installation.. <br>16A 2P+E<br>

od193216/2020_2021 : Supply, Installation, Testing and commissioning of Tie-Strips.<br>

SUPER STRUCTURE

od346309/2020_2021 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Anjili Frame size 100x80 mm for flush door

od80465/2020_2021 : Supplying, fixing, testing and commissioning of following Y - STRAINERin the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.with Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified.25 mm Dia

od61678/2020_2021 : Supply,Installation,Testing and Commissioning of Air Release Valve GM 20mm dia type of approved make.

19.8.1.1 : Extra for depth for manholesSize 90x80 cmWith common burnt clay F.P.S. ( non modular ) bricks of class designation 7.5

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

od346998/2020_2021 : Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water chilled water MS C-class pipe, installed with grooved couplings(with necessary clamps, vibration isolators ,elbows, reducer,and fittings.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g polythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing feltstrip(as per IS:1322 as amended up to date) at joints repairing of damage to building etc with necessary supports and accessories as per specifications and as required complete in all respect.40 mm dia. (50 mm thick insulation)

7.1.4 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 185 sq. mm and upto 400 sq. mm

Additional Safety Works

od91484/2020_2021 : Supply, Installation, Testing & Commissioning of Electrical control panel: Manual operation, All Switch gear- MCB, OLR, Single Phase Preventer, H/L Protection, Volt meter, Push Button, Indication Lamp, flow meter etc of approved Make for Level based On-off Control Valves provided with float switch etc.<br>

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

od196082/2020_2021 : Supply, Installation and Commissioning of Isolation Ball Valve - SS 31<br>25 mm dia.

od171452/2020_2021 : Supply and fixing cast iron lever operated slim seal type butterfly valves of CI body and spheroidal graphite iron disc (SG iron),with nitrile rubber seal, tested to 10 kg / sq.cm Confrming to BS 5155 / MF6 standards and including a set of GI flanges as per BS-10 table 1 including bolt nuts, and Neoprene rubber gaskets etc.,complete as required.65 mm nominal bore

od78173/2020_2021 : LIGHTING CONTROLS FOR CAR PARK AREA <br>Supplying, installation, testing & commissioning of Advance presence detection by Microwave technology. The sensor range is corner/ceiling mount 20 meter X 20 meter at a recommended mounting height of 3.5 meter. To control lighting load of 10 A, with features of delay time 5- 20 min, Passive photocell and Dual Sensitivity for Range. The sensors shall come withhandheld controllers for providing local user overide including all accesories as required (HONEYWELL MR1500P or equivalent)<br>

od315187/2020_2021 : DATA CENTER HVAC PANEL <br>Fabrication, supply, installation, testing & commissioning of cubical type, dust and vermin proof,wall mounted, front operated MV panel board, sheet steel enclosure with door sheet steel all round foamed-in PU seal with dipcoat primed, powder coated on the outside, textured paint with zinc-plated mounting plate. The colour shall be RAL 7035 with IP 66 protection, NEMA 4 protection category, IK08 impact resistance with hinged doors, all round solid construction, gland plate, mounting plate, Doors are to be fitted with conceal hinge with name plate, danger notice board, including all switchgears and components as shown in the schematic drawing. All opening parts of the panel shall be sealable. <br>This panel should include pluggable type surge arrester Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 37.5 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up HRC fuse as required and as directed. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. <br>Incomers<br>Incomer 1 & 2 - 160A 25kA FP MCCB with Thermal Magnetic based setting - 2 nos<br>160A ATS (ASCO) - 1 no<br>160A 415V, 36kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>"96x96 mm size multifunction meter as per IEC 62053-21 for class 1 having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be integrated with SCADA - 2 Set<br><br>"<br>RYB phase indicating LED lamps with control fuses and switches - 2 set.<br>Class B+C/ Class 1+2 Surge arrestor device with necessary rating HRC fuses for protection of same - 1 set.<br>Outgoings<br>100A 25kA TP Thermal magnetic based MCCB -3 nos<br>40A 25kA TP Thermal magnetic based MCCB -2 nos<br>"96x96 mm size multifunction meter as per IEC 62053-21 for class 1 having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be integrated with SCADA - 5 Set<br>Supply, Installation, testing and commisioning <br>

od184265/2020_2021 : Supply, Installation, testing and commissioning of Differential pressure sensor with all necessary support and accessories

od189199/2020_2021 : Supply, Installation, Testing & Commissioning of Exit Push Button with below specifications as minimum and all the necessary accessories<br> - Type - NO/NC<br> - Materials - Stainless Steel<br> - Suitable GI Backboxe

od177224/2020_2021 : Supply, Installation, Testing and commissioning of fully automatic Nitrogen Control Panel with minimum flow rate of 500LPM or above<br>

od170256/2020_2021 : Providing and fixing CP towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour.

od69617/2020_2021 : Supply ,Installation and testing and commissioning of Fan coil Units complete with chilled water cooling coil, centrifugal fan, cleanable fabric filters, flushing by pass arrangement, insulated condensate drain pan (extended), coil piping connections (bimetallic union/union connectiors), condensate drain connections, return air plenum with dampers, Flexible duct connectors, including thermostats that are BMS compatible, temperature controller, and sensors along with the control box, its transformer, relays, necessary power and control wiring between the thermostat, controller, FCU, PICV as shown in the drawings and specifications. All units shall be suitable for 240 +/-10% volts, 3 speed and required lengths of wiring 3.5 TR, 1400 CFM<br>

50.18.9.9.1 : Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

16.61 : Providing Retro - reflective regulatory sign board of size 900 mm diameter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro reflective sheeting as approved by Engineer-in-Charge. Letter, symbols, borders etc. will be as per IRC. 67 with required colour scheme on the boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of M.S. angle 50x50x4 mm , 4 m long welded to the frame with adequate anti-theft arrangement. Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat ( primer ) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer- in-charge .

od72156/2020_2021 : Providing and fixing M.S. grills using suitable sections on to the walls with sufficient bearings on walls including applying a priming coat with approved steel primer and including cost and conveyance of all materials hire and labour charges etc. complete.<br>

od91482/2020_2021 : Providing of 4 pair 1.5 sq mm cable as control cable of liquid water level controller through a ISI Heavy duty 20mm conduit<br>

od61674/2020_2021 : Supply and Fixing of weather proof Hose cabinet suitable size "having made of 16 gauge MS Sheet with common keylock arrangements, suitable to accommodate two lengths of 15mtr hoses,and one no branch pipe with nozzle. The cabinet shall be painted to scarlet red colour out side and off-white inside.

od189197/2020_2021 : Supply, Installation, Testing & Commissioning of Standalone Biometric Time & Attendance Machine with below specifications as minimum and all the necessary accessories<br> - Fingerprint Capacity - 3000<br> - Transaction - 1,00,000<br> - Identification Speed - <= 1 Sec<br> - Communication - TCP/IP, USB

IBMS

od80422/2020_2021 : Supplying, fixing, testing and commissioning of BALL VALVE (MANUAL) in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.with C I body , PN 16 pressure rating for chilled water/ hot eater circulation as specified,25 mm dia.

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

od5105/2021_2022 : Supply & installation of Celling Mounted Surgical Double Dome LED OT light with Integrated Camera System and third arm to mount medical display 21’’ or more. (See Annexure A - OT Technical specification)<br>

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

od79737/2020_2021 : LT CABLE SUPPLY<br>Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br>4cx4sq.mm Al Cable<br>

od66304/2020_2021 : Supply and installation of in position the signages "FIRE ORDER" it should contain the following matter on 3mm thick "Opaque" PVC foam board of computerized cut, PVC Non-reflective self adhesive vinylepainted foamboard of 3'x4'. Samples has to approved by the Architect before procuring the same.A) ALERT THE SECURITY BY ACTUATING MANUAL CALL POINT LOCATED AT STRATEGIC LOCATIONS. B) EVACUATE THE OCCUPANTS BY USING FIRE EXITS AND EMERGENCY EXITS ONLY, AND ASSEMBLE AT VARIOUS ASSEMBLY POITS. C) IF POSSIBLE TRY TO EXTINGUISH THE FIRE BY USING NEAREST / SUITABLE PORTABLE FIRE EXTINGUISHER OR WATER FROM NEAREST HOSE REEL. D) BE CALM AND DO NOT GIVE ANY ROOM FOR PANIC. WALK, DO NOT RUN. E) IF YOU ENCOUNTER SERIOUS DIFFICULTY IN EVACUATION ,LAY FLAT AND TRY TO ATTRACT ATTENTION OF RESCUE TEAM. F) TRY TO COVER YOUR FACE WITH A WET TOWEL TO AVOID BREATHING SMOKE OR OTHER TOXIC FUMES. ACTION BY SECURITY / RECEPTION UPON RECEIPT OF INFORMATION THROUGH FIRE ALARM OR PUBLIC ADDRESS SYSTEM. A) ALERT THE OCCUPANTS BY USING PUBLIC ADDRESS SYSTEM. B) INFORM FIRE CONTROL THROUGH ANYONE OF THE FOLLOWING PHONE NUMBERS:101 /………………….( Local fire station number) C) REFER EVACUATION PLAN.D) GUIDE THE FIRE FORCE, ON THEIR ARRIVAL TO THE SEAT OF FIRE. E) IN CASE OF CASUALTIES, CALL AMBULANCE (Local numbers:) PHONE : -----------------------

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

od80535/2020_2021 : HT CABLE LAYING<br>Laying of following 11kV (E) grade XLPE insulated PVC sheathed compact circular armoured aluminium conductor HT power cable, insulation screened with extruded semi conducting compound in separate existing cable tray using factory made clamps and the spacing between clamps will not exceed 60cm.<br>Above 120 sq. mm and upto 400 sq. mm<br>

od187442/2020_2021 : Supply, laying, testing and commisioning of 4Cx 1.0 Sqmm PVC insulated, Tinned Copper Conductor Cable- Unscreened<br>

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

od171441/2020_2021 : Providing and fixing ball valve (brass) of approved quality with all acessories, High or low<br>pressure, complete with all acessories :32mm dia

od178029/2020_2021 : Ball Valve, DN 80 - 76x1,5<br>

od91325/2020_2021 : Supply, Installation, Testing & CommissDisc or Tube Type Coarse Bubble Diffusers with Design Flow rate of 10 m3/hr with EPDM membrane construction, 24 Nos with associated Pipe work in MSEP up to Main Header and uPVC ASTM Sch 40 Pipe for Wetted Parts for Aeration Grid as required in Collection tanks, Equalization tank, Chemical precipitation tank etc.ioning of Aeration Grid with Coarse Bubble Diffusers.<br>

od63017/2020_2021 : ABOVE GROUND :Providing, laying, testing & commissioning of 'C' class heavy duty GI Pipes conforming to IS 3589/IS 1239 including threaded fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 32 mm dia

od346992/2020_2021 : Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water chilled water MS C-class pipe, installed with grooved couplings(with necessary clamps, vibration isolators ,elbows, reducer,and fittings.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g polythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing feltstrip(as per IS:1322 as amended up to date) at joints repairing of damage to building etc with necessary supports and accessories as per specifications and as required complete in all respect.150 mm dia. (75 mm thick insulation)

od171453/2020_2021 : Providing and fixing ball valve (brass) of approved quality, High or low<br>pressure, with all fitting acessories :50 mm nominal bore

7.8.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

od80347/2021_2022 : Providing granite topped counter ( excluding cost of granite slab) with stoage shelf below using good quality 18mm BWP ply wood laminated on all exposed sides with approved lmm thick laminates and 0.8mm thick white laminates on the inside including providing pull out drawer, lower side panels, lower back panel, divider panels etc. Providing vertical supports at every 90cm or near, providing approved company made handles, bolts, locking arrangements & all necessary hardware fittings like drawer sliders, wire manager etc. placed in position correctly with provision to draw cables etc.as per detailed drawing & specification.<br>

od193211/2020_2021 : Supply, Installation, Testing and commissioning of PVC Milky Transparent Straight.<br><br>

od187430/2020_2021 : Supply, installation testing and commisioning of Air Flow Switch .<br>

od190177/2020_2021 : Supply, Installation, Testing & Commissioning of 48 PoE Layer -2 Port Network Switch 10/100/1000 Mbps with 2 SFP slots minimum loaded with 10G Uplink

od195767/2020_2021 : SITC of Catridge Filter 1No. of Unit :<br>Type of Cartridge :<br>Rating :<br>Flow Rate :<br>Feed Water Turbidity :<br>No. of Cartridge :<br>MOC of Housing :<br>One<br>PP Spun bonded type<br>5 micron<br>3000 LPH.<br>5 NTU<br>2 Nos. 500 mm long x 100mm dia.<br>(shall be indicated by the<br>Tenderer)<br>SS 316.<br>

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

od196046/2020_2021 : Stainless steel (SS 316L) seamless tube piping conforming to ASTM,<br>A213 standards and valves/strainers with stainless dteel (SS 316) body<br>and impeller, from pre-treated water connection flange to the final<br>connection to various equipment listed in Clause 2.4.1 of the technical<br>specifications<br>Piping - 25 mm dia.

od75886/2020_2021 : LIGHTNING PROTECTION<br>Supply, installation, testing and commisioning of Lightning counter - To count no of lightning strike & it can record the date and time of the lightning incident.Tested from a laboratory acredited by UL, KEMA or VDE to be mounted inside enclosure including suitable weatherproof cabinet of sleek design as approved by client representative and all accesories required for complete installation <br>

od318780/2021_2022 : Supplying, installation, testing & commissioning of fire fighter telephone handset<br>complete as required.

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

od78080/2020_2021 : EARTHING <br>Supply and laying the following sizes of Cu strips laid 0.6 m below ground level including excavating trench of suitable size and refilling ,including necessary clamps and bolts etc and all accessories as required for complete installation as instructed by engineer in charge/consultant. <br> 25x3mm Cu strips tinned at the point of contact

od78965/2020_2021 : MCCB:<br>Supply, fixing, testing and commisioning of following rating, breaking capacity and pole, type MCCB in existing Vertical Distribution Board with spredear links, terminal connections and all accesories as required making all necessary connections etc as required and instructed by engineer in charge/consultant.<br>125 Amp 16kA FP MCCB with Thermal-Magnetic Release<br>

13.52.2 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

od314431/2020_2021 : Supply of below sized XLPE insulated PVC sheathed Aluminum conductor armored cabling to the incoming and outgoing of fire pump panel including necessary termination, glanding, necessary connections etc 3Cx 150 sq mm on wall, floor

od4967/2021_2022 : Supply, Installation, Testing and commissioning of Oxygen Manifolds - 2 banks x 10 cylinders with all accessories etc.<br><br>

od246214/2020_2021 : Providing and fixing stainless steel tower bolts ISI marked with necessary screws etc. complete : 300x10 mm

1.17.4 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.4 x 1.5 sq. mm

od183361/2020_2021 : Supply, Installation, Testing and Commissioning of A Conventional Rate of Rise Heat Detector (White) incorporating a 60°C fixed temperature element. The thermistor and linearising Circuits provide an accurate linear response Heat Detector. A third Terminal provides integral remote indicator output.

od63018/2020_2021 : ABOVE GROUND :SUPPLY, INSTALLATION, TESTING & COMMISSIONING of GI heavy duty grade 'C' class pipe (IS:1239 Part-I) including cutting, threading etc. bends, elbows reducers, clamps, hangers etc. including cutting holes in brick or RCC walls/slabs and making good the same complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade including all steel work. 25 mm dia

od170474/2020_2021 : Providing and fixing grating of CP brass 2 in 1, gratings 150mm outer & 100mm inside with screwing facility approved quality and colour.

50.18.8.6.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

od78868/2021_2022 : Carrying out initial vertical load tests as per relevant IS code including all arrangements for measuring deflections and submitting report as per specification including making pile head for testing at the required level, supporting / reaction arrangement ( including reaction piles/ soil/ rock anchors if any) for the kentledge load.1000mm dia piles ( 2.5 times the theoretical design vertical load capacity of 328 tonne .<br>

od79978/2020_2021 : END TERMINATION<br>Supply and making end termination with brass double compression gland, earth clip and aluminum lugs/ Cu lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminum conductor cable of 1.1kV Grade as reqiured.<br>5Cx1.5 sq.mm Cu Control Cable<br>

od195760/2020_2021 : SITC of Fabricated RO water storage tanks of capacity indicated below, veritcal<br>cylindrical, made out of full stianless steel (SS 316) and of thickness<br>5mm for shell and 8mm for dished ends, with inlet/ outlet/ overflow/ drain/<br>vent connections, stainless steel valves/fittings, 450 mm dia manhole with<br>bolted cover, capacity / safety controls, control panels, complete in all<br>respects.<br>b) 4000 Litres Capacity for Other Mecial Equipment listed in Clause 2.4.1 of<br>the technical specifications (size 1600 mm dia and 2200 mm height).<br><br>

od73351/2020_2021 : Wall Fan<br>Supply, installation, testing and commisiong of 450mm sweep wall fan on surface including mouting and providing all accessories required for complete installation, testing, commisioning etc as required complete (Havells Airboll Hi-Speed or equivalent)<br>

Collection Pit of Size 2Mx2Mx1.75M

od315190/2020_2021 : DATACENTER PANEL 1<br>Supplying, installation, testing & commissioning of partially type tested cubical type, dust and vermin proof, floor mounted, front operated MV panel board, symmetrical, stable profile frame based construction. LT panel board of suitable size for 415V, 3 phases, 4 Wire 50 Hz AC supply system having provisions of cable end termination chambers and fabricated in compartmentalized design. Panel should have a fully corner welded construction with more than 15 fold profile with min 25mm din pitch pattern. All load bearing members like partial doors should be from 2mm DD grade CRCA with 2mm GI mounting plate. All the internal partitions should be galvanised sheets of 1.6mm.All painted non load bearing members like full height side cover, full height bolted covers should be 1.5mm. All raw sheets should be cleaned thoroughly from all directions by a conveyorized cleaning process to avoid salt sedimentation at corners. After pre cleaning, all the flat sheets should undergo Electrophoretic dip coating and powder coating with RAL 7035 or RAL 7032.The thickness should be 80-120microns. All doors should have a poly urethane form gasketing for higher IP protection with 2 Nos. earth stud, cable alleys, removable gland plates. Modular, easily extendable TS profiled Enclosure systems with Horizontal and / or vertical bus bar and cable compartment, with standard gland plates. Cubicle Separation plate, cross members and equipment mounting plates are galvanized Iron (GI). Partial doors, covers are with PU foamed gaskets integrated to ensure high degree (IP54) of ingress protection. Doors are to be fitted with conceal hinge with name plate, danger notice board, heavy including all switchgears and components as shown in the schematic drawing. All opening parts of the panel shall be sealable. The panel shall be type tested and the enclosure shall be made in accordance with IEC 61 439-1/-2 and certificates of test reports to be furnished. <br>This panel should include pluggable type surge arrester Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 37.5 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up HRC fuse as required and as directed. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. <br>Incomers<br>Incomer 1 & 2 - 400A 36kA FP MCCB with Microprocessor based setting - 2 nos<br>400A ATS with AMF (ASCO) - 1 no<br>400A 415V, 36kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required.<br>"96x96 mm size multifunction meter as per IEC 62053-21 for class 1 having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be integrated with SCADA . - 2 Set<br><br>"<br>RYB phase indicating LED lamps with control fuses and switches - 2 set.<br>Class B+C/ Class 1+2 Surge arrestor device with necessary rating HRC fuses for protection of same - 1 set.<br>Outgoings<br>200A 25kA TP MCCB Thermal Magnetic based - 1 nos<br>160A 25kA TP MCCB Thermal Magnetic based - 1 nos<br>100A 25kA TP MCCB Thermal Magnetic based - 3 nos<br>"96x96 mm size multifunction meter as per IEC 62053-21 for class 1 having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be integrated with SCADA - 5 Set<br><br>"<br>Potential free contacts shall be made availiable as required for integrating electrical system with IBMS. Required provisions shall be made availiable for the same as per IO summary of IBMS.<br>Supply, Installation, testing and commisioning

od178534/2020_2021 : Horizontal Bed Head Panels of 3 feet long with provision for 3 nos electrical (power & data) & min 3 nos Gas outlets - as per technical specification for beds<br>

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

16.11.4.9 : Supply, Installation, Testing and Commissioning of following sizes electronic, selfbalancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valves in a single body. The actuator shall be capable of accepting upto 1 OV DC and upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and not be less than 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 1625mm dia.

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

od81265/2020_2021 : THREE PHASE DIRECT MULTIFUNCTION METER<br>Supply, installation, testing and commisioning of Multifunction Meter DIN Rail Mounted with Three Phase Direct Input up to 125A, Cl 1.0 Accuracy, with LCD Display, able to measure Parameters Voltage, Current, Active Power & Active Energy and able to communicate via RS485 Modbus Protocol to connect with Energy Management / Building Management System including all accesories as required to be installed in tier DBs, enclosures etc as required..<br>

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

od178333/2020_2021 : Probes<br>

od81671/2020_2021 : Supply, fixing, testing and commisioning of following rating, breaking capacity and pole, type thermal magnetic based MCCB in existing ACDB with spreader links, terminal connections and all accesories as required making all necessary connections etc as required and instructed by engineer in charge/consultant.<br>80Amp 16kA FP MCCB with Thermal-Magnetic Release

1.21.3 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

od81823/2020_2021 : Supplying and laying of following size DWC HDPE pipe lSI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required.<br>63 mm dia (OD-63 mm & ID-51 mm nominal)

od187322/2020_2021 : Supply, installation testing and commisioning of DDC CONTROLLERS : Automation stations / DDC Controller with I/O module etc., The controllers shall be NATIVE BACNET IP based. The controller shall be with 32 bit microprocessor, working in standalone or networkable mode, with real time clock and historical database & Peer to Peer Communication. The controller shall support minimum of 8 trend log objects, 10 program areas and 8 PID loop objects. The DDC's shall store programs and program parameters in non volatile memory. The DDCs shall be housed within a suitable MS enclosure complete with all protection, terminals, wiring and accessories.[ Note: The selection of DDC controller shall be as per I/O schedule ] DDC for Medical Gas System<br>

od78875/2021_2022 : Carrying out static routine vertical load tests as per relevant IS coded including all arrangements for measuring deflection and submitting reports as per specification and approved drawing including making of pile head for testing the required level, supporting / reaction arrangement ( including reaction piles/ soil/ rock anchors if any) for the kentledge load.900mm dia piles ( 1.5 times the theoretical design vertical load capacity of 265 tonne ) .

od90090/2021_2022 : Supply ,Installation and testing and commissioning of Secondary CHW Pumpset- Variable speed End suction back pullout type Chilled water pumps of specified make and capacity complete with base frame, motor coupling, mechanical shaft seal, nosing frames for the pedestals,floating floors and as per specification and equipment schedule with BMS compactability , VFD and Control Panel. electrical cabling from the starter panel to the relevant pumps, to be priced under this scope with all necessary supports and accessories.CI body with bronze impeller and IE3 efficiency class motor. (3Working + 1Stand By),Flow : 960(US GPM),Head : 35(Mtr)<br>

od318756/2021_2022 : Supplying, installation, testing & commissioning of intelligent analog addressable<br>photothermal detector complete with mounting base complete as required.

od196080/2020_2021 : Supply, Installation and Commissioning of Isolation Ball Valve - SS 31<br>40 mm dia.

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

od187437/2020_2021 : Supply, installation testing and commisioning of Ambient Temperature Sensor( Outdoor )<br>

od61671/2020_2021 : Supplying and fixing single headed internal hydrant valve with instantaneous<br>Gunmetal coupling of 63 mm dia with cast iron wheel ISI marked conforming<br>to IS 5290 (Type -A) with blank Gunmetal cap and chain as required :Single headed Gunmetal

od79722/2020_2021 : PVC BOX<br>Supplying and fixing following size/modules, PVC open surface box / recess boxes to be placed on surface/recess for modular switches etc as required as instructed by engineer in charge<br>4 module<br>

od190195/2020_2021 : Supply, Installation, Testing and commissioning of HDMI Cat5e Box Type receiver runs up to 70 mtr.

od171558/2020_2021 : Supply and fixing cast iron lever operated slim seal type butterfly valves of CI body and spheroidal graphite iron disc (SG iron),with nitrile rubber seal, tested to 10 kg / sq.cm Confrming to BS 5155 / MF6 standards and including a set of GI flanges as per BS-10 table 1 including bolt nuts, and Neoprene rubber gaskets etc.,complete as required.150 mm nominal bore

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

od73468/2020_2021 : Inline Fans - for Toilet, Plant room exhaust: Supply, installation, testing and commissioning Direct driven axial flow fans suitable for mounting on wall or duct in standard galvanized/ powder coated steel construction with required rating, static, single motor and flexible connection to connect with ducting / plenum, louvers with bird screen 2460 CFM ESP 14mm

od80890/2020_2021 : MAIN LIFT PANEL<br>Supplying, installation, testing & commissioning of partially type tested cubical type, dust and vermin proof, floor mounted, front operated MV panel board, symmetrical, stable profile frame based construction. LT panel board of suitable size for 415V, 3 phases, 4 Wire 50 Hz AC supply system having provisions of cable end termination chambers and fabricated in compartmentalized design. Panel should have a fully corner welded construction with more than 15 fold profile with min 25mm din pitch pattern. All load bearing members like partial doors should be from 2mm DD grade CRCA with 2mm GI mounting plate. All the internal partitions should be galvanised sheets of 1.6mm.All painted non load bearing members like full height side cover, full height bolted covers should be 1.5mm. All raw sheets should be cleaned thoroughly from all directions by a conveyorized cleaning process to avoid salt sedimentation at corners. After pre cleaning, all the flat sheets should undergo Electrophoretic dip coating and powder coating with RAL 7035 or RAL 7032.The thickness should be 80-120microns. All doors should have a poly urethane form gasketing for higher IP protection with 2 Nos. earth stud, cable alleys, removable gland plates. Modular, easily extendable TS profiled Enclosure systems with Horizontal and / or vertical bus bar and cable compartment, with standard gland plates. Cubicle Separation plate, cross members and equipment mounting plates are galvanized Iron (GI). Partial doors, covers are with PU foamed gaskets integrated to ensure high degree (IP54) of ingress protection. Doors are to be fitted with conceal hinge with name plate, danger notice board, heavy including all switchgears and components as shown in the schematic drawing. All opening parts of the panel shall be sealable. The panel shall be type tested and the enclosure shall be made in accordance with IEC 61 439-1/-2 and certificates of test reports to be furnished. <br>This panel should include pluggable type surge arrester Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with potential free contact, thermal dis connector & provision for inbuilt common remote indication for defective arresters to connect between Line and Neutral and one number arrester Spark Gap type to connect between Neutral and Earth of following ratings including base element & pluggable arresters. Nominal voltage -230V 50Hz, type single MOV with built in thermal fuse and cooling gel(L to N) & spark gap encapsulated / non exhausting (N to E) . Lightning Impulse Current - 37.5 kA (10/350µ sec) for Line to Neutral & 25 kA(10/350µ sec) for Neutral to Earth,Nominal discharge current-30 kA (8/20µ sec) for Line to Neutral & 40 kA(8/20µ sec) for Neutral to Earth, max discharge current 150 kA (8/20µ sec) for Line to Neutral & 50 kA(8/20µ sec) for Neutral to Earth. Voltage protection level 1300V (L to N) & 1200V (N to E). Operating temp -40º to +80ºC. Response time <25 nano sec (L to N), < 100 nano sec (N to E) DIN rail mounting type etc complete with back up HRC fuse as required and as directed. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. <br>Incomers<br>Incomer - 250A TPN Isolator - 1 no<br>250A 415V, 36kA best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required.<br>"96x96 mm size multifunction meter as per IEC 62053-21 for class 1 having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be integrated with SCADA - 1 Set<br><br>"<br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Class B+C/ Class 1+2 Surge arrestor device with necessary rating HRC fuses for protection of same - 1 set.<br>Outgoings<br>100A 25kA TP MCCB Thermal Magnetic based - 1 nos<br>80A 25kA TP MCCB Thermal Magnetic based - 7 nos<br>63A 25kA TP MCCB Thermal Magnetic based - 2 nos<br>"96x96 mm size multifunction meter as per IEC 62053-21 for class 1 having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be integrated with SCADA - 10 Set<br><br>"<br>Supply, Installation, testing and commisioning <br>

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

od79054/2021_2022 : Providing and fixing SS lock of size suitable for aluminium door with SS screws etc.<br>complete as per direction of Engineer-in-Charge

od189201/2020_2021 : Supply, Installation, Testing & Commissioning of Double Leaf Door Lock with below specifications as minimum and all the necessary accessories<br> - Type - Double Leaf<br> - Holding Force - 600lbs<br> - Inbuilt Magnetic Contact for door status monitoring<br> - Anti rust treated for surface<br> - LED Indication for EM Lock status<br> - Including all the mounting brackets

1.38 : Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Oxygen Supply System

od195759/2020_2021 : SITC of Centrifugal monobloc RO water circulation pumps with all accessories,<br>motors and starters.<br>Note :<br>Pump head, motor and starter shall be as per actual requirement<br>a) For circulation from Storage Tank to Dialysis Machines<br>i) Flow : 336 LPH<br>ii) Head : 25 Mt<br>

od79735/2020_2021 : LT CABLE SUPPLY<br>Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br>2cx10sq.mm Al Cable<br>

od80212/2020_2021 : Supply of superior quality copper tubular cable socket and making core termination of cables of the following sizes including crimping etc. as required.<br>185 sq.mm<br>

od70846/2020_2021 : Supply installation testing and commissioning of AMCA Certified Inline Centrifugal fresh air Fans shall be with direct driven centrifugal fan, circular section, suitable for ceiling suspension/mounting,dol Starter panel. The units shall be complete with flexible duct connections at inlet and outlet. The motor shall be protected by thermal contact relay as protection against burn-out. as specified and as indicated in the equipment schedules and drawings for the following:1272 CFM, ESP 17mm

od77136/2020_2021 : EARTHING <br>Supply and laying the following sizes of strips on cable tray or wall surface, including necessary clamps (each clamp not exceeding 60 cm) and bolts etc as required for complete installation as instructed by engineer in charge/consultant. <br>Copper wire No.10 SWG <br>

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

od78976/2020_2021 : Isolator With Enclosure<br>Supply and fixing of FP CRCA sheet steel powder coated enclosure on surface/recess along with following Amps, 415V, DP/FP isolators confirming to IEC 60947-3 complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation.<br>32A FP Isolator with enclosure<br>

12.47.1 : Providing & fixing UV stabilised fibre glass reinforced plastic sheet rooting up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8 mm dia G.I plain/ bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovings incorporating minimum 0.3% ultra-violet stabiliser in resin system under approxirnately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.2 mm thick corrugate 2.5"or 4.2" or 6") or step-down (2' or 3" or 6") as specified.

od66312/2020_2021 : Supply and fixing of 4 Kg ABC Dry Powder (Stored Pressure) Type Fire Extinguisher. pressurized with dry nitrogen gas at 15 bar. Design, construction and testing as per IS 2190, Testingand Inspection - As per IS 15683, Squeeze Grip Type, ISI and CE marked on the Extinguisher, Hydrostatic pressure tested Certificate, Supplied with standard accessories.

3.6 : Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m

od313902/2020_2021 : Solid block masonry using pre cast Fly ash solid blocks (Factory made with a minimum fly ash composition of 40%) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

1.24.8 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Bell push

5.2.a : Providing and applying tack coat with bitumen emulsion( RS) using emulsion pressure distributor at the rate of 0.20 - 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

od7464/2021_2022 : Supply, Installation, Testing and commissioning of 4 X 2 HDMI Matrix Switcher

od79724/2020_2021 : MCCB:<br>Supply, fixing, testing and commisioning of following rating, breaking capacity and pole, type MCCB in existing Vertical Distribution Board with spredear links, terminal connections and all accesories as required making all necessary connections etc as required and instructed by engineer in charge/consultant.<br>100 Amp 16kA FP MCCB with Thermal-Magnetic Release<br>

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

od196083/2020_2021 : Supply, Installation and Commissioning of Isolation Ball Valve - SS 31<br>50 mm dia.

od91480/2020_2021 : Supply, Installation, Testing & Commissioning of Filter Feed Pumps MoC: Cast Iron, Duty: Continuous, Packing: Mechanical Seal, with a Flow Rate of min 300 LPM or above at a Head >25 m In a configuration of 1 Working & 1 Standby, Power- 5 HP, with Outlet Pressure monitoring, Strainers, Recirculation Valves, Check Valves & all required accessories etc. Complete<br>

od190194/2020_2021 : Supply, Installation, Testing and commissioning of HDMI Cat5e Box Type transmitter runs up to 70 mtr.

od81192/2020_2021 : SINGLE PHASE DIRECT METER<br>Supply, installation, testing and commisioning of Modular Single-Phase Meter DIN Rail Mounted, Direct Input up to 40A, Cl 1.0 Accuracy, with Electro Mechanical 7 Digit Display able to measure Active Energy up to 999999.9 kWh and with Pulse Output for integrating with Energy Management System including all accesories as required to be installed in DBs, enclosures etc as required..The meter shall be with RS485 port for communication with SCADA sooftware<br>

od187441/2020_2021 : Supply, laying, testing and commisioning of 2Cx 1.0 Sqmm PVC insulated, Tinned Copper Conductor Cable- Unscreened<br>

od207/2021_2022 : "Supply and fixing of following FP 415V, isolators in CRCA powder coated sheet steel enclosure with door interlock and padlock facility on surface with terminal shrouds on both sides and phase barriers included<br>Conforms to IEC 60947-3, IS/IEC 60947-3e complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation."<br>125A FP Isolator with enclosure<br>

od72739/2020_2021 : INTERIOR LIGHT FIXTURES <br>Supply of 28 W recess mounted 2' x 2' LED luminaire with system light output greater than 3600 lumens and system efficacy >125 lm/W. The luminaire must be energy efficient with CRI>80, CCT - 6500, pf > 0.95, THD <10% SDCM<5, IP20 protection. The luminaire shall be flicker free with a ripple content less than 5 %. The luminaire housing shall be made of CRCA and diffuser material of PS and a lifetime of 50,000 burning hours as per L70B50 criteria, 4 kV internal surge protection. The luminaire must be BIS certified and must have LM79 and LM80 reports from NABL certified labs (Make : Philips RC380B LED36S-6500 PSU or equivalent) <br>

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

od73453/2020_2021 : Inline Fans - for Toilet, Plant room exhaust: Supply, installation, testing and commissioning Direct driven axial flow fans suitable for mounting on wall or duct in standard galvanized/ powder coated steel construction with required rating, static, single motor and flexible connection to connect with ducting / plenum, louvers with bird screen 2132 CFM ESP 20mm

od353205/2020_2021 : Providing and fixing Door frame and Shutter made of 46mm thick steel fire check door of 120 minutes fire rating confirming to BS: 476 Part 22 and IS: 3614 Part II for stability and integrity, fabricated with 2 nos. 22 gauge thick galvanized steel sheet with infill of fire rated Acrylic Sealant and non-combustible core bonded to both faces of sheet with lock seam joints at stile edges and internal reinforcement at top, bottom and stile edges for Fire Rating. The door frames are manufactured from 18 gauge thick galvanized steel sheet pressed from to single rebate profile of size 125mm x 75mm. The frames shall be fixed using canon/hilti anchor bolts of size 10mm dia x 100mm long. The door frames and door shutters are finished with powder coating paint. The cost includes providing and fixing of minimum two-hour fire rated stainless steel ball bearing hinges 125 mm x 75mm x 3mm. The cost includes providing opening for vision panel of required size in shutters (cost of glass excluded) and fixing vision panels of specified size with complete fire rated gasket channel & moulding beading and filling the gap between moulding /beading and glass with suitable sealant.<br>

od5109/2021_2022 : Supply & installation of Ceiling Supply Unit for mounting Display system for OR Integration (Spring-loaded Arm/ Arm Type) (See Annexure A - OT Technical specification) • Should be able to fix two monitors in the single pendent.

od73117/2020_2021 : EXTERIOR LIGHT FIXTURES <br>Supply and installation of GI aesthetically good looking tubular pole 3m height, hot dip galvanised for mounting of Post top luminiare applied with primer and paint<br>

od79983/2020_2021 : END TERMINATION<br>Supply and making end termination with brass double compression gland, earth clip and aluminum lugs/ Cu lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminum conductor cable of 1.1kV Grade as reqiured.<br>4Cx4sq.mm Al Cable<br>

od80536/2020_2021 : HT CABLE SUPPLY<br>Supply of following 11kV (E) grade XLPE insulated PVC sheathed compact circular armoured aluminium conductor HT power cable, insulation screened with extruded semi conducting compound in combination with copper tape suitable for 11kV earthed system confirming to relavent standard. <br>3cx240sq.mm XLPE Cable<br>

13.83.2 : Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile including applying additional coats wherever required to achieve even shade and colour.Two coats

od85329/2020_2021 : Supply and Fixing Equipotential bonding rail for Lightning Arrestor applications(Test Joint). Equipotential bonding rail for equipotential bonding according to DIN VDE 0100-410/540 and lightning protection equipotetial bonding according to DIN VDE 0185-305. Base plate and cover hood from polystyrene. Colour: Black, UV resistant. Can be used outdoor also. Screw and crossbar made of VA. Capable of carring lightning current 100KA (10/350). Connection options: 7 x single or multi-core conductors to 25mm square or fine core conductors to 16mm square. 1 x round cable Rd 8-10. 1 x flat strip to FL 30 or round cable RD 8-10 including corrosion tapes and all accesories as required for complete installation as instructed by engineer in charge. To be connected to structural earthing mesh at a height of 2.5m from ground level for testing purpose

od80564/2020_2021 : AUTOMATIC TRANSFER SWITCHES (ATS)<br>Supply, installation, testing and commisioning of following rated four pole ATS switches in suitable size enclosure as per rating and size. Supply, installation, testing & commissioning of cubical type, dust and vermin proof, wall mounted, front operated, sheet steel enclosure with door sheet steel all round foamed-in PU seal with dipcoat primed, powder coated on the outside, textured paint with zinc-plated mounting plate. The colour shall be RAL 7035 with IP 66 protection, NEMA 4 protection category, IK08 impact resistance with hinged doors, all round solid construction, gland plate, mounting plate, Doors are to be fitted with conceal hinge with name plate, danger notice board, including all switchgears and components as shown in the schematic drawing. All opening parts of the panel shall be sealable. Cutout provision for viewing the controller and source one - center off –source two switches shall be availiable in the enclosure for direct operation without opening the doors. RYB phase indication lamps shall also be provided in the enclosure from both sources. Provision for incoming cables and outgoing cables as per schematic to be also provided and provision for adding seperate UNCO module to be provided with each ATS for integrating ATS controller with SCADA software. Seperate provision for running control cable for communication with EMS shall also be provided<br>All transfer switches should be as per IEC60947-6-1 standards with minimum AC33B utilization category and with controller having RS485 port communicable with modbus for obtaining all parameters from controller for both sources. The automatic transfer switch shall consists of an intelligent controller and Modular load break switch which transfers the load to the secondary power source when it detects under/over voltage, under/over frequency, or phase failure.The switch shall have three possible operating positions (source one - center off –source two). The two sources can be isolated in the center off position. A position locking mechanism should also be provided. Phase loss sensing needs to be provided .<br>"The automatic transfer switches and accessories shall conform to the requirements of<br>• EN 60947-6-1 / IEC60947-6-1: transfer switching<br>• EN60947 -3 / IEC60947-3: Suitable for Isolation<br>• EN55022: Radiated and Conducted Emission,Class A<br>• EN61000-3-2: Harmonic Current Emission, Class A<br>• EN61000-3-3: Limits of Voltage fluctuation and Flicker<br>• EN 61000-4-5: Immunity to Surge<br>• EN 61000-4-4: Immunity to Electrical Fast Transient:<br>• EN61000-4-2: Immunity to Electrostatic Discharge<br>• EN61000-4-3: Immunity to Radiated Electric Fields<br>• EN 61000-4-6: Immunity to Continuous Conducted Interference<br>"<br>"The controller should pocess following features - Different Optional Modes (Source I priority /No Source priority), Controller Display Having Indicator -programming the features and settings, Switch position indicator lights, Source acceptability indicator lights on the front door panel.,Controller should be capable of detection of under and over voltage settings on source I and source II, Under and over frequency settings on source I and source II, Voltage unbalance detection between phases, under frequency transfer ,over frequency transfer, High frequency switching power supply, and wide power voltage range, Center-off with time delay and center-off with protection - The center-off time delay can be set to avoid large current rushes to inductive loads, Center-off with protection is available to protect critical loads <br>"<br>The ATS should have automatic and manual bypass operation. With electrical and mechnical interlocks to prevent both sources being connected simultaneously with high short circuit capability and rotaing dual contactor design to extinguish the arc quickly and effectively.(ASCO or equivalent) Add on RS485 Modbus Communication Module. BSEM(Breaker status & control Module) & IFM(Interface module) modules shall also be considered for integration with SCADA. ATS shall have priority as source 1 and will shift to source 2 when power fails in source 1 even if power is availiable in both sources priority shall be for source 1. Space provision fro installing of UNCO module for each ATS for communicating with SCADA software shall also be considered along with this scope in the enclosure (DIN rail mounted or Base mounted)<br>250A FP ATS <br>

od221298/2020_2021 : Providing 10cm thick precast RCC slab 1.2m long 0.60cm wide with 9 numbers of 2.5cm dia drain holes placed at qual distacne , neatly finished and placed in position on top of drainage leaving 2cm clear gap between each slab for drainage etc. complete as per specification.<br>

od248482/2020_2021 : Supply,Installation, Testing and Commissioning of Manifold fabricated from seamless pipe Pipe (S) : M.S. Seamless To ASTM A-106, SCH. 80 (3-way).

od253507/2021_2022 : Supply of 120 L Bio Bins

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

od306195/2020_2021 : Providing and fixing Cubicle curtains in the wards suitable for beds laid. The rate includes all cost of cloth, curtain track, supports, hardware items, stitching charges and all labour charges including conveyance, loading unloading etc. complete in all respect. The length of curtain cloth should have 1metre more length than the channel length. The height of curtain should have 7.5feet or standard approved ht. payment shall be made only as per site measurements of works actually done. (Curtained track length only shall be measured for payment) for All multi bed areas (Recovery, ICU, General wards Palliative wards, Procedure rooms, etc)<br>

od81199/2020_2021 : SOFTWARE, SERVER, DESKTOP & OTHER ACCESORIES<br>Supply, installation testing and commisioning of PLC system, programmable according to IEC 61131 standard, with Automatic reporting of system events and presenting them on the display, in the web server, Integrated communication protocols (MODBUS TCP), Integrated security functions like access protection, Support Counters, Timers, Analog input / Outputs, Convenient programming environment by providing analog register and index register, With analog dedicated register (U) and monitoring dedicated function, convenient use for I/O is maximized. with processing time of 0.06μs/Steps, Watchdog timer, Memory error detection, IO error detection, Modbus communication: RS232, RS485 & Ethernet (Dual Port) Modbus TCP/IP, CANopen, DeviceNet, PROFIBUS, RAPIEnet, EtherNet/IP Convenient network-diagnostic function through network & communication frame monitoring including all accesories as required for complete installation for use in panels to be placed inside panels to control ACBs & MCCBs with SCADA software. (Make - L&T XLB-U or equivalent)<br>

od183407/2020_2021 : Supply, Installation, Testing and Commissioning of HFC 227ea Gas (1,1,1,2,3,3,3 Hepta fluro propane), Zero ODP, Stored Pressure 25BAR.

od183438/2020_2021 : Supply, Installation, Testing and Commissioning of Wire Sleeve Aluminum.

od72742/2020_2021 : Inline Fans - for Toilet, Plant room exhaust: Supply, installation, testing and commissioning Direct driven axial flow fans suitable for mounting on wall or duct in standard galvanized/ powder coated steel construction with required rating, static, single motor and flexible connection to connect with ducting / plenum, louvers with bird screen 10000 CFM ESP 14mm

od79984/2020_2021 : END TERMINATION<br>Supply and making end termination with brass double compression gland, earth clip and aluminum lugs/ Cu lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminum conductor cable of 1.1kV Grade as reqiured.<br>4Cx6sq.mm Al Cable<br>

od79124/2020_2021 : Supplying, fixing, testing and commissioning of following NON - RETURN VALVE of C I body vulcanized NBR seal flanged end & PN16 pressure rating as specified -25 mm dia

9.1.10 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 X 35 sq. mm (28mm)

od71819/2020_2021 : Supply and installation of 3 nos 990L capacity day tanks to be provided in a closed enclosure. The capacity of the fuel tank supplied has to be capable for 8 Hrs continuous operations @ 80% load. Supply shall include • Fuel tank pipe from ibuilt tank to day tank and return, Refueling and drainage plugs, welding sleeves and fixing material, insulation, couplers and all accesries along with automatic pumping system for fuel refilling should be considered in ths scope of work including necessary length fuel pipe as per manufacturer recommendation and accesories for providing DG fuel piping to DG day tanks for all DG sets, providing couplers, insulation, installation and all accesories required, supply and providing of pumping system from day tank with automatic operation using controller, connecting to pump, providing connections complete as required. Fuel piping from storage shall be done in such a way that the piping is not permanantly connected to the day tanks, it can be removed after refueling. Hence total capacity of fuel tank for DG set will not exceed permissible limits.<br>

od193206/2020_2021 : Supply, Installation, Testing and commissioning of the following accessories for Stations:<br>d)Station Directory<br><br>

od7460/2021_2022 : Supply, Installation, Testing and commissioning of 43" Full HD LED Display with necessary accessories

od349614/2021_2022 : "<br>"" Supply, Installation, Testing and Commissioning of factory built Ceiling Suspended Chilled water Double Skin horizontal Air handling units made of 40mm thick panels consisting of pre plasticized GI casing of thickness 0.8mm outside layer and inner layer shall be of 0.8mm plain GI sheet with polyurethane form(PUF) insulation factory injected between them by injection moulding machine with thermal break profile complete with fan section with backward curved plug fans suitable for static pressure as required with VFD drives , coil section with aluminium finned copper tubes (min. 10 fins per inch, tube thickness not less than 0.5mm),Cooling coil of 6 rows deep, filter section with 50mm thick metal viscous/washable synthetic type air prefilters (10 micron) mixing box with fresh air & return air intakes with dampers,drain connections, SS drain pan(18G) with PUF insulation, TEFC sq.cage induction motor of efficiency class IE3 suitable for 415+-10% volts, 50 Hz, 3 phase AC supply including mounting and fixing arrangements, anti vibration springs/ isolator bearings etc complete as per specification and of following capacities.The cost shall be inclusive of VFD starter panel in a separate enclosure with necessary rating incomer isolator / MCCB /contactor with all accessories including necessary connections, inter connections and control wiring with pressure sensors (minimum 2 Nos.) for complete installation. Only HVAC application VFDs shall be used.<br>Horizontal Ceiling Suspended AHU 10.5 TR/ 2628 CFM/ 6 RD/ ESP - 152 Pa<br>

17.7.9 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Surgeon Type wash basin of size 660x460 mm with single 15 mm C P. brass pillar taps with elbow operated levers ISI marked

od91469/2020_2021 : Providing & fixing, testing and commissioning of SS centrifugal Waste water Transfer Pump(grinder pump), for pumping waste water/ Kitchen waste/ sewage waste from collection pit to Sewage treatment plant, with  including control panel, solenoid valves, level switches, control wires etc. (1Working pump+standby) with suitable HP MAKE : Capacity:200lpm@30mtr head

od286229/2021_2022 : Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units with 41.1% of light transmission, 16.3 % outdoor relection and 18.1% indoor reflection with solar factor of 0.2365 and shading coefficient of 0.2719 and energy factors of 30.6% transmission ,32.2% relection , 36.2% indoor reflection, 35.5 % absorption(AE1) and1.70% Absorption (AE2) with thermal transmission of ug 1.541 W/m2.k etc.of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in- Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm

od75648/2020_2021 : Supply, installing, connecting to existing sandwich rising mains, testing and commissioning of following rating T Joint for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick electro galvanised steel sheet enclosure, IP54, complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. The end feed unit shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of end feed unit shall be furnished. including 2 runs of 25x6 mm size copper stirp run through the surface <br>1250A T Joint<br>

11.46.2 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

od249943/2020_2021 : Providing indoor potted plants well developed from top to bottom in clay/ plastic/ khurja pot with spill water holding containers including all necessary allied backups etc. complete as per specification and instruction of engineering in charge.-Jade plant<br><br>

od80556/2020_2021 : Fabrication, supply & installation of DG adaptor box for 650kVA, including painting etc as per technical specifications provided including all accessories for complete installation for extending of DG bus bar, including bus bar extension and making ease for providing cable terminations complete as required<br>

od318772/2021_2022 : Supplying, installation, testing & commissioning of intelligent addressable thermal<br>detector with rate of rise cum fixed tempreature thermistor complete with base as<br>required.

1.27.3 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

Nitrous Oxide Supply System

od190176/2020_2021 : Supply, Installation, Testing & Commissioning of 24 PoE Layer -2 Port Network Switch 10/100/1000 Mbps with 2 SFP slots minimum loaded with 10G Uplink.

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

od166745/2021_2022 : Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 250 mm dia 6 Kgf/cm2

9.147B.1 : 543 SUB HEAD : 9 - WOOD & PVC WORK 9.147B Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately).br Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

od78172/2020_2021 : ELECTRICAL CAR CHARGING SOCKETS (NORMAL PLUG & SOCKET) <br>"Supply, installation, testing and commisioning of IP65 & IK10 protection, Plug & Interlock Socket Board-1 set, surface mounted type with following inbuilt accesories -<br>Incoming: 32A DP RCBO 300mA - 1 No.<br>Single phase Modular Meter DIN Rail Mounted, Direct Input up to 40A, Cl 1.0 Accuracy, with Electro Mechanical 7 Digit Display able to measure Active Energy up to 999999.9 kWh and with Pulse Output, RS485 module for integrating with SCADA software - 1 No.<br>Outgoing:<br>IP44 32A 3pin Plug & Interlock Socket - 1 No.<br>Including all connections and interconnections as required and as approved by client/consultant.<br>"<br>

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

od73464/2020_2021 : Inline Fans - for Toilet, Plant room exhaust: Supply, installation, testing and commissioning Direct driven axial flow fans suitable for mounting on wall or duct in standard galvanized/ powder coated steel construction with required rating, static, single motor and flexible connection to connect with ducting / plenum, louvers with bird screen 300 CFM ESP 16mm

od188020/2020_2021 : Extra for every additional lead of 100m beyond initial lead of 50m of the excavated / stacked material all kind of soil

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

od178893/2020_2021 : Supply, installation, testing and commissioning of Twin Oxygen Flow meter with humidifier bottle at one end and nebulisation adaptor at other end. Matching probe / adaptor shall be provided at both ends.<br>

od189648/2020_2021 : Supply, Installation, Testing & Commissioning of 18U Network Rack with below specifications as minimum and all the necessary accessories<br> - Height - 18U<br> - Dimensions - 600 x 600<br> - Fan Units with 4 Fans<br> - PDU 6 point 5 Amps<br> - Mounting Hardware Kit (1 lot)<br> - Tray<br>- Front glass doors and back steel door and side panels

1.50.1 : Installation of exhaust fan in the existing opening, including making good the damage connection testing, commissioning etc. as required.Upto 450 mm sweep

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

13.13 : 12 mm cement plaster 1:2 ( 1 cement : 2 stone dust)

18.17.1A : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore

od73467/2020_2021 : Inline Fans - for Toilet, Plant room exhaust: Supply, installation, testing and commissioning Direct driven axial flow fans suitable for mounting on wall or duct in standard galvanized/ powder coated steel construction with required rating, static, single motor and flexible connection to connect with ducting / plenum, louvers with bird screen 250 CFM ESP 13mm

od80937/2020_2021 : 4 way SMDB 21<br>Supply, erection, testing and commissioning of wall mounting type, double door 3 phase 4 way SMDB. IP43 ingress protection and quality with cable end boxs, meter module, bottom add on module for adding surge arrestor including busbar, neutral link and DIN bar with all accessories etc complete with all connections and inter-connections as shown in the schematic drawing, Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant. SMDB shall comply with latest IEC 61439-2 standard with full safety reliability test certificates (Dekra and Asta certified). All MCCBs used shall be 100% Ics rated. Short-time withstand current for SMDB should be 36kA for 1s. SMDB shall be supplied with following accesories-<br>250A rated SMDB - 4 way with all accessories - 1 no.<br>Meter extension Box - 1 set<br>"96x96 mm size multifunction meter as per IEC 62053-21 for class 1 having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be integrated with SCADA Software - 1 Set<br><br>"<br>RYB indication lamps - 1 set<br>Side cabling box - 2 nos.<br>Bottom cabling box with provision for adding Surge arrestor alongwith HRC fuses for backup of arrestor - 1 no <br>Mounting base - 1 no.<br>Corner box - 4 nos<br>Incomer - 200A FP 36kA thermal magnetic release MCCB -1No. (Ics 25kA)<br>Outgoings<br>100A 25kA TP MCCB, with thermal magnetic release - 4 nos<br>Supply , installation, testing and commisioning<br>

16.11.4.10 : Supply, Installation, Testing and Commissioning of following sizes electronic, selfbalancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valves in a single body. The actuator shall be capable of accepting upto 1 OV DC and upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and not be less than 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 1620mm dia.

od188787/2020_2021 : Supply, Installation, testing and commissioning of Indoor type IR Fixed Bullet Camera with below specifications as minimum and with all the necessary accessories for the installation<br> - 3.6mm Fixed Lens<br> - 2MP Resolution<br> - H.265, H.264, MJPEG codec<br> - Edge Storage (Minimum 32GB)<br> - IR - 30 meters<br> - 120dB WDR<br> - IK10, IP66<br> - PoE

od70850/2020_2021 : Supply installation testing and commissioning of AMCA Certified Inline Centrifugal fresh air Fans shall be with direct driven centrifugal fan, circular section, suitable for ceiling suspension/mounting,dol Starter panel. The units shall be complete with flexible duct connections at inlet and outlet. The motor shall be protected by thermal contact relay as protection against burn-out. as specified and as indicated in the equipment schedules and drawings for the following:2203 CFM, ESP 22mm

16.17 : Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminum with aluminum volume control dampers with anti smudge ring and removable core.

1.55.1 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group A

od248837/2020_2021 : Supplying, fixing, testing and commissioning of flow switch on pipes of suitable diaRmtras shown and as specified in the specifications and drawings

od71831/2020_2021 : EXHAUST PIPES<br>Supply, erection, commissioning of additional length of exhaust pipes with long radius bend from residential silencer with necessary clamps, fixtures, civil works and painted with heat resistant, rust proof, bituminous paint of approved colors to a maximum of 10 m in stages of following sizes including suitable rain cap for top to avoid rain water entry. The distance between exhaust pipe at top and rain cap should be higher than diameter of pipe. It is also recommended that horizontal run of exhaust piping should slope downwards away from engine to the condensate trap. Silencer should be installed with drain plug at bottom. Fixing shall be done with proper clamps, expansion bolts, and all other acessories as instructed by the Engineer and the rate inclusive of all minor civil works required, bolts, clamps etc as required for istallation. Support to exhaust piping should be done in such a manner that load of exhaust piping is not exerted to turbocharger. Exhaust pipe height shall be 3m more than the top of any adjacent building withing 10m radius of the exhaust.<br>300mm dia <br>

od61875/2020_2021 : <br>" Supply, Installation, Testing and Commissioning of factory built Floor mounted Chilled water Double Skin horizontal Air handling units made of 40mm thick panels consisting of pre plasticized GI casing of thickness 0.8mm outside layer and inner layer shall be of 0.8mm plain AL sheet with polyurethane form(PUF) insulation factory injected between them by injection moulding machine with thermal break profile complete with fan section with backward curved plug fans suitable for static pressure as required with VFD drives , coil section with aluminium finned copper tubes (min. 10 fins per inch, tube thickness not less than 0.5mm),Cooling coil of 8 rows deep, filter section with 50mm thick metal viscous/washable synthetic type air prefilters (10 micron) & 5 micron fine filters, mixing box with fresh air & return air intakes with dampers,drain connections, SS drain pan(18G) with PUF insulation, TEFC sq.cage induction motor of efficiency class IE3 suitable for 415+-10% volts, 50 Hz, 3 phase AC supply including mounting and fixing arrangements, anti vibration springs/ isolator bearings , strip heaters (3x1.5KW), germicidal UV-C lamps etc complete as per specification and of following capacities.The cost shall be inclusive of VFD starter panel in a separate enclosure with necessary rating incomer isolator / MCCB /contactor with all accessories including necessary connections, inter connections and control wiring with pressure sensors (minimum 2 Nos.) for complete installation. Only HVAC application VFDs shall be used.<br>Horizontal Floor mounted AHU 8.1 TR/ 4242 CFM/ 8 RD/ ESP -235 Pa

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

od195756/2020_2021 : SITC of Conductivity Indicator (CI) :Conductivity Sensor/Indicator.<br>On-Line Sensor.<br>

od318979/2021_2022 : Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

od183431/2020_2021 : Supply, Installation, Testing and Commissioning of 2C x 1.5 Sq.mm CU. Armoured control / power Cable. Voltages grade 1100 Volts.

od78884/2021_2022 : Carrying out static routine vertical load tests as per relevant IS coded including all arrangements for measuring deflection and submitting reports as per specification and approved drawing including making of pile head for testing the required level, supporting / reaction arrangement ( including reaction piles/ soil/ rock anchors if any) for the kentledge load.700mm dia piles ( 1.5 times the theoretical design vertical load capacity of 162 tonne .

od160665/2021_2022 : Providing and fixing false ceiling 250 mm x 6 mm thick multi chamber hollow PVC panel .The support from ceiling is to be provided using 25 mm x 25 mm size aluminum square tube pipe at a distance of 2 ft (Framing work) with complete fitting etc complete as per specification.

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

CCTV SYSTEM

15.1 : Supplying,Installation, testing and commissioning of Passive Infrared (PIR) technology based occupancy sensor having high preformance, non regulating programmable type, suitable for connected load upto 10 Amp, for mounting height up to 2.8 Mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming and site etc. complete as required

od195306/2020_2021 : Providing and fixing / holding sinages, sign board made of compact aluminium panel sheet or HPL sheet of approved shade , providing 3mm vinyl pased letters with multi language (engilsh & malayalam) and logos of approved sizes, providing side hangers fixing in position,providing centre handers using Ms rods amn chains etc. displaying scope of services, room numbers, doctors rooms, HOD rooms, floor wise facilities ,radiation sinages, mandatory notification as directed by the engineer in charge with one side lettering for fixed in wall and both sides as in projected type etc. complete to detailed pre approved plan.<br>Stair area 120x100cm<br>

od286109/2021_2022 : <br>Painting with synthetic enamel paint having VOC (Volatile Organic Compound) content less than 150 grams/ litre of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of<br>approved brand and manufacture .

od79088/2021_2022 : Providing and fixing SS D handle of size 450mm with SS screws etc. complete as per direction of Engineer-in-Charge.

od70921/2020_2021 : Supply installation testing and commissioning of AMCA Certified Inline Centrifugal fresh air Fans shall be with direct driven centrifugal fan, circular section, suitable for ceiling suspension/mounting,dol Starter panel. The units shall be complete with flexible duct connections at inlet and outlet. The motor shall be protected by thermal contact relay as protection against burn-out. as specified and as indicated in the equipment schedules and drawings for the following:1122 CFM, ESP 17mm

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

od69912/2020_2021 : Supply installation testing and commissioning of AMCA Certified Inline Centrifugal fresh air Fans shall be with direct driven centrifugal fan, circular section, suitable for ceiling suspension/mounting,dol Starter panel. The units shall be complete with flexible duct connections at inlet and outlet. The motor shall be protected by thermal contact relay as protection against burn-out. as specified and as indicated in the equipment schedules and drawings for the following:1214 CFM, ESP 18mm

od187450/2020_2021 : Supply and laying of Perforated Cable Tray with cover and Accessories - 100mmX50mmX2mm<br>

od188608/2020_2021 : Providing and fixing buffalo grass existing ground prepared with proper level and ramming with required tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and even, watering with sprinkle

2.11 : Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

od324916/2020_2021 : Providing and fixing white vitreous china pedestal type floor mounted water closet (European type W.C. pan) with seat and lid, 3/6 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (twin flush), with flow rate of 4.5 lpm (50 % below griha base rate) including flow regulator with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid.

od314715/2020_2021 : Required Gateway / Open Protocol Software for integrating the following third party system communicating on one of the Standard Open Protocols such as BACNet , MODBUS, M-Bus, etc - Vendor to consider required No. of Integrators and controllers for qty's mentioned in IO summary<br>BTU Meters

od81819/2020_2021 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (provision for MCCB as incomer & MCB as outgoings) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)<br>12 way Double door

od78960/2020_2021 : RCBO<br>Supplying, fixing, testing and commissioning following four pole and double pole , 415 volts and 240 volts, residual current circuit breaker with overload protection (RCBO) of the following rating and sensitivity current in the existing MCB SPN and TPN horizontal/vertical DB's complete with connections, etc. as required and instructed by engineer in charge/consultant..<br>25A 100mA DP RCBO<br>

od82238/2020_2021 : Supply, installation, testing and commissioning of 20 persons passenger/bed lift, side opening, machine room less ,serving 15 stops / 15 openings, 2 mps. Size of lift well is 2150mmx2950mm. Travel distance 58000mm

od302230/2021_2022 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.<br>

od249945/2020_2021 : Providing indoor potted plants well developed from top to bottom in clay/ plastic/ khurja pot with spill water holding containers including all necessary allied backups etc. complete as per specification and instruction of engineering in charge.-Majesty palm<br><br>

od66296/2020_2021 : Providing and installation in position the following type of sign boards made out of 3 mm thick "Opaque" PVC foam board with computer cut,Photoluminescent type self glowing vinyle painted foam board,complete with mirror fastners, glasscovering etc.Samples has to approved by the Architect before procuring the same. Floor indentification signages (ie,GROUNDFLOOR,FIRSTFLOOR,…etc.) at each stair enclosure on every floor,indicating the floor number in words,lettering size shall be7.5cm with contrasting colour from background.

od80915/2020_2021 : 4 way SMDB 23<br>Supply, erection, testing and commissioning of wall mounting type, double door 3 phase 4 way SMDB. IP43 ingress protection and quality with cable end boxs, meter module, bottom add on module for adding surge arrestor including busbar, neutral link and DIN bar with all accessories etc complete with all connections and inter-connections as shown in the schematic drawing, Providing all connections and interconnections as required and providing all assecories as required for complete installation as instructed by engineer in charge/consultant. SMDB shall comply with latest IEC 61439-2 standard with full safety reliability test certificates (Dekra and Asta certified). All MCCBs used shall be 100% Ics rated. Short-time withstand current for SMDB should be 36kA for 1s. SMDB shall be supplied with following accesories-<br>250A rated SMDB - 4 way with all accessories - 1 no.<br>Meter extension Box - 1 set<br>"96x96 mm size multifunction meter as per IEC 62053-21 for class 1 having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be integrated with SCADA Software - 1 Set<br><br>"<br>RYB indication lamps - 1 set<br>Side cabling box - 2 nos.<br>Bottom cabling box with provision for adding Surge arrestor alongwith HRC fuses for backup of arrestor - 1 no <br>Mounting base - 1 no.<br>Corner box - 4 nos<br>Incomer - 160A FP 36kA thermal magnetic release MCCB -1No. (Ics 25kA)<br>Outgoings<br>80A 25kA TP MCCB, with thermal magnetic release - 4 nos<br>Supply , installation, testing and commisioning<br>

od90439/2020_2021 : Providing and fixing of floor traps (4'') and fixing CP gratings of approved quality and colour. Rectangular type with openable circular lid. 150 mm nominal size square 100 mm diameter of the inner hinged round gratings to toilet floors and making good the concrete floor as per direction of engineer in charge

16.11.4.6 : Supply, Installation, Testing and Commissioning of following sizes electronic, selfbalancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valves in a single body. The actuator shall be capable of accepting upto 1 OV DC and upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and not be less than 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 1650mm dia.

od81592/2020_2021 : Copper MC Connectors for solar panels with silver coated, bush bakelite with lock provision for both male and female for positive and negative as a set for each solar panel

5.8 : Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

od7458/2021_2022 : Supply, Installation, Testing and commissioning of pole mount kit for the projector

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

od84534/2020_2021 : Supply,installation,testing and commisioning of Public Address speaker with talk back facility 6 Watts with LMT and call switch, made out of powder coated CRC A sheet ,wall mounting type and to be installed at a height of not less than 150 CM from the finished floor levels, suitable for concealed mounting.

od76602/2021_2022 : Providing heavy duty FRP manhole cover and frame of size 90cmx60cm internal dimension with load bearing capacity of 2.5 tonne made of polyester resin , fiber glass and fillers of approved quality fixing in correct line and level as directed by Engineer-in-charge.

od353208/2020_2021 : Supply of vision panel in fire rated doors of 200 mm x 500 mm size made out of minimum 5 mm thick clear fire rated glass (imported) for 120 minutes fire rating of fully transparent in fire/non-fire conditions having minimum 93% transparency, in accordance with IS : 3614 Part -II and BS : 476 Part 20& 22 , for 120 min. fire rating for stability and integrity and insulation criteria .<br>

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

od189202/2020_2021 : Supply, Installation, Testing & Commissioning of Access Control Management & Time and attendance software with below specifications as a minimum and all the necessary licenses<br> - Support for client workstations/ users - Minimum 10 or more<br> - Intrusion System integration<br> - Card Reader Support ( with the proposed entry/ exit readers)<br> - Fingerprnit reader Support ( with the proposed entry/ exit readers)<br> - Minimum number of employee/ user profiles - 1,00,000<br> - Number of reader support - Minimum 300 or higher<br> - Guard Tour System<br> - Maps Integration<br> - Surveillance System Integration - 20 NVRs/ 1200 cameras<br> - Support Client-Server Architecture<br> - Web Support<br> - Time and attendace report<br> - 128 bit AES Data Encrypted communication between the door controllers

od193209/2020_2021 : Supply, Installation, Testing and commissioning of PVC Grey Straight.<br><br>

od187288/2020_2021 : Supply, installation testing and commisioning of SOFTWARE: Web Based Graphical interface software based on MS Windows 10 / Latest. The system should be accessible from anywhere on LAN or WAN or Ethernet without additional licenses. The Communication protocol shall be Industry Standard BACNET Open Protocol. System should be scalable. The software shall be open system architecture type which facilitates interoperability with other system over BACNET IP with complete control and monitoring functions. Software shall work in the WEB environment supporting HTML5, unlimited concurrent client users license on LAN / WEB. Software shall be certified and complying to BACnet Advanced Operator Workstation

od63838/2020_2021 : <br>" Supply, Installation, Testing and Commissioning of factory built Ceiling Suspended Chilled water Double Skin horizontal Air handling units made of 40mm thick panels consisting of pre plasticized GI casing of thickness 0.8mm outside layer and inner layer shall be of 0.8mm plain GI sheet with polyurethane form(PUF) insulation factory injected between them by injection moulding machine with thermal break profile complete with fan section with backward curved plug fans suitable for static pressure as required with VFD drives , coil section with aluminium finned copper tubes (min. 10 fins per inch, tube thickness not less than 0.5mm),Cooling coil of 6 rows deep, filter section with 50mm thick metal viscous/washable synthetic type air prefilters (10 micron) & 5 micron fine filters, mixing box with fresh air & return air intakes with dampers,drain connections, SS drain pan(18G) with PUF insulation, TEFC sq.cage induction motor of efficiency class IE3 suitable for 415+-10% volts, 50 Hz, 3 phase AC supply including mounting and fixing arrangements, anti vibration springs/ isolator bearings etc complete as per specification and of following capacities.The cost shall be inclusive of VFD starter panel in a separate enclosure with necessary rating incomer isolator / MCCB /contactor with all accessories including necessary connections, inter connections and control wiring with pressure sensors (minimum 2 Nos.) for complete installation. Only HVAC application VFDs shall be used.<br>Horizontal Ceiling Suspended AHU 7.0 TR/ 2200 CFM/ 6 RD/ 144 Pa,6 Row

od90459/2020_2021 : Supplying, Installing & Testing at site in position PVC Rodding Eye (6 kg/cm2) complete in all respects.<br>110 mm dia <br>

NURSE CALLING SYSTEM

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

od79090/2020_2021 : Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic<br>operation and consisting of following, complete in all respects, as required :<br>(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless<br>steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC,<br>synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55<br>protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.<br>(c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.<br>(d) Suitable cement concrete foundation duly plastered with anti vibration pads.2280lpm @100 mtr head

od75650/2020_2021 : Supply, installing, connecting to existing sandwich rising mains, testing and commissioning of following rating End cover unit for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick electro galvanised steel sheet enclosure, IP54, complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. The end feed unit shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of end feed unit shall be furnished. including 2 runs of 25x6 mm size copper stirp run through the surface <br>800A<br>

od79723/2020_2021 : RCBO<br>Supplying, fixing, testing and commissioning following four pole and double pole , 415 volts and 240 volts, residual current circuit breaker with overload protection (RCBO) of the following rating and sensitivity current in the existing MCB SPN and TPN horizontal/vertical DB's complete with connections, etc. as required and instructed by engineer in charge/consultant..<br>32A 100mA DP RCBO<br>

od75177/2020_2021 : Supply, installation, testing and commissioning of following capacity type tested as per IEC 61439 Part 6, pre-fabricated sandwich, Multi-layer insulated with each layer having Class F (155 Degree) PET (Poly ehteline terephthalate) insulation , compact, sandwitched indoor type (TPN With 100% Neutral ) bus trunking on wall / ceiling / structure, with high conductivity electrical grade aluminium (60% conductivity, 99.6% purity) conductor in convenient sections suitable for 3 phase 4 wire 50Hz, 415V, AC supply. The bus bar shall be complete with bends, expansion joints, fire barriers at wall/ceiling crossing, copper flexible end connections, elbows, adaptor boxes for termination in panels . The housing shall be constructed from 1.6mm (min) thick electro galvanised sheet steel enclosure, IP54 with epoxy coated. The busduct shall be complete with 4 nos aluminium busbar of same size. Earthing with 2 runs of copper earth of size 25 x 6 mm copper strip (Cu strip shall go inside LT panels and end termination boxes) on each side including clamping bracket, angle iron bracket, steel fastners, connecting to earthing system etc as required, including supports for bus bars. The bus duct shall comply with IEC and BS standards. The routine test certificate as per IS / IEC and type test certificate of identical bus trunking shall be furnished. Rate shall be quoted for including all type of bends, complicated bends as per site condition, copper flexible conductors for termination, supports, hangers, flanged ends, adaptor box with terminal kits and all accesories required for complete installation. (Bus bar connection between transformers and panel, DG synch panel and Main panel and from other panel to panel connection is considered in this item)<br>2500A Al TPN IP54 Feeder busduct<br><br>

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

od248871/2020_2021 : Providing and laying FRP lining water proofing treatment in retaining wall as per specification. The application shall be done only after cleaning of surface, there after applying powder with resin, compound, then laying of FRP lining (fiber glass lamination) by applying resin with blue pigment etc. as per manufactures specification. Application of first coat resin with chalk powder on the corner, uneven surface and undulation and laying the o Fiber glass lamination with resin and blue pigment, o Surface mat lamination with resin. The second coat application shall be done with applying resin with Paraffin wax, chalk powder and blue pigment etc. complete. The rate includes preparation of surface, pressure grouting over slab & side wall, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry and testing of applied area complete.<br>

od158074/2020_2021 : Supplying & Fixing at site in position Fabricated u PVC Astm Sch 80 Puddle flanges in the underground and overhead water tanks as per the drawings and the requirement of the Project Manager.-150mm dia

2.7.1 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Ordinary rock

od190225/2020_2021 : Supply, Installation, Testing & Commissioning of Patient Handsets - type without wired console unit.

od192165/2020_2021 : Providing and laying anti skid vitrified tiles of size 600x600 mm or more (thickness to be specified by the manufacturer) of Ist quality conforming to IS: 15622 of approved make in all colours, shades, except white, Ivory, Grey Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with epoxy grouting and matching pigments etc., complete.

od187439/2020_2021 : Supply, installation testing and commisioning of PH Sensor<br>

50.18.9.10.1 : Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

od315537/2021_2022 : Providing and fixing UPVC pipes, having mfor cold water supply including all UPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work-50 mm nominal outer dia Pipes

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

od79112/2020_2021 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required<br>250mm dia :

od347003/2020_2021 : Supplying, laying/ fixing, testing and commissioning of following nominal sizes of condenser water water MS C-class pipe, installed with grooved couplings(with necessary clamps, vibration isolators, elbows, reducer,and fittings etc.)with necessary support and accessories,250 mm dia

od91210/2020_2021 : Supply, Installation, Testing & Commissioning of Coarse Screen for sewage.MoC: SS 304, Angle of Inclination – 45 deg, Frame in 1” Square Pipe and Bars made of 10 mm Square Pipe with 12 mm Spacing with suitable facility to remove trapped materials.<br>