Bus Stands Management And Development Authority Tender

Providing and fixing uplasticised PVC connection pipe with brass unions :-45cm ( Forty five centimeter) Length:- 15mm (Fifteen milimeter) nominal bore, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing divisional plate for urinals 600mmx330mm (Six hundred milimeter into Three hundred thirty milimeter) vitreous china confirming to BIS specification, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make : 15mm (Fifteen milimeter) nominal bore , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing steel reinforcement for R.C.C. work including bending, binding and placing in position including cost of binding wire complete, upto floor all levels Thermo-Mechanically Treated bars of grade Fe-500D or more., including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete, 150x10 mm (One hundred fifty into Ten milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Water Supply and Sanitary Installation:- Providing and fixing water closet squatting pan (Indian suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two ormore coat applied @ 0.90 ltr/ 10 sqm (Zero point nine zero liters per ten square meter) over an under coat of primer applied @ 0.80 ltr/10 sqm (Zero point eight zero liters per ten square meter)of approved brand and manufacture, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Finishing walls with water proofing cement paint of required shade:- New work (Two or more coats applied @3.84 kg/10 sqm (Three point eight four Kilogram per ten square meter) , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing 100 mm (One hundred milimeter) sand cast Iron grating for gully trap, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (One Cement isto Three coarse sand isto Six graded stone aggregate) 20 mm (Twenty milimeter) nominal size, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing 600x450mm (Six hundred into Four hundred fifty milimeter) bevaled edge mirror of superior glass (of approved quality) complete with 6 mm (Six milimeter) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible:-32 mm (Thirty two milimeter) dia, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion, (i) Single socketed pipes :- 110 mm (One hundred ten milimeter) diameter, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm (One point six zero milimeter) thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm (Fifty into Twenty five milimeter), or base ties of 1.60 mm, (One point six zero milimeter) pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm (Two point five milimeter) thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Fixing with adjustable lugs with split end tail to each jamb, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc.complete, 100 mm (One hundred milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and applying plaster of paris putty of 2 mm ( Two milimeter) thickness over plastered surface to prepare the surface even and smooth complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Constructing brick masonry manhole in cement mortar 1:4 (One cement isto Four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (One cement isto One and half coarse sand (zone- III) 3 (Three) graded stone aggregate 20 mm (Twenty milimeter) nominal size, foundation concrete 1:4:8 mix (One cement isto Four coarse sand (zone- III) isto 8 (Eight) graded stone aggregate 40 mm (Forty milimeter) nominal size), inside plastering 12 mm (Twelve milimeter) thick with cement mortar 1:3 (One cement isto Three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two coarse sand isto Four graded stone aggregate) 20 mm (Twenty milimeter) nominal size finished with a floating coat of neat cement complete as per standard design :-Inside size 90x80 cm (Ninety into Eighty centi meter) and 45 cm (Forty five centi meter) deep including C.I. cover with frame (light duty) 455x610 mm (Four hundred fifty five into Six hundred ten milimeter) internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) With common burnt clay F.P.S. (nonmodular) bricks of class designation 7.5, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing 40x5 mm (Forty into five milimeter) flat iron hold fast 40 cm (Forty centimeter) long including fixing to frame with 10 mm (Ten milimeter) diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm (Thirty into Ten into Fifty centimeter) 1:3:6 mix (One cement isto Three coarse sand isto Six graded stone aggregate) 20mm (Twenty milimeter) nominal size, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382 leaving 10 mm(Ten milimeter) gap for thermal expansion:- Collers:- 75mm (Seventy five milimeter) diameter, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete, 100x10 mm (One hundred into Ten milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of unserviceable materials up to approved dumping site, and serviceable material to be handed over to the department, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

12 mm (Twelve milimeter) cement plaster on fair side of single half brick wallmix:-1:6 (One cement isto Six fine sand), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

6 mm ( Six milimeter) cement plaster of mix 1:3 (One cement isto Three fine sand), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete., 100x58x1.90 mm (One hundred into Fifty eight into One point nine zero milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382 leaving 10 mm (Ten milimeter) gap for thermal expansion:- Collers:- 100mm (One hundred milimeter) diameter, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (One Cement isto Two coarse sand isto Four graded stone aggregate) 20 mm (Twenty milimeter) nominal size, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion, (i) Single socketed pipes :- 75mm (Seventy five milimeter) diameter, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing 12mm thick prelaminated particles board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge. Pre-laminated particle board with decorative lamination on both sides, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Stone soling properly hand packed filling interstices with spall and consolidating with power road roller to the requested gradient and camber including spreading watering and rolling of binding materials moorum or earth etc, complete as per HP. PWD specification. 100mm spreed thickness (Finished work including materials and labour), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15mm (Fifteen milimeter) nominal bore, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382 leaving 10 mm (Ten milimeter) gap for thermal expansion:- Bend:- 75mm (Seventy five milimeter) diameter, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc.complete, 125 mm (One hundred twenty five milimeter), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% (Zero point zero eight percent) and conforming to IS:15622, of (Kajaria, Nitco, Somany,Orient, RAK,Jonson & Jonson) make, in all colours and shades, laid on 20mm (Twenty milimeter) thick cement mortar 1:4 (One cement isto Four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (Three point three kilogram per Square meter) including grouting the joints with white cement andmatching pigments etc., complete Size of Tile 600x600 mm (Six hundred into Six hundred milimeter) , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Centering and shuttering including strutting, propping etc. and removal of form for :- Suspended floors, roofs, landings, balconies and access platform, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (One cement isto Three coarse sand), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Reinforced cement concrete Mechnically Mixed and vibrated work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (One Cement isto One and half coarse sand isto Three graded stone aggregate) 20 mm (Twenty milimeter) nominal size, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing G.I. pipes complete with G.I. fitting and clamps, i/c cutting and making good the walls etc :-15 mm (Fifteen milimeter) dia nominal bore, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382 leaving 10 mm (Ten milimeter) gap for thermal expansion:- Bend:-100mm (One hundred milimeter) diameter, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm (Four hundred thirty into Two hundred sixty into Three hundred fifty milimeter) or 340x410x265 mm (Three hundred forty into Four hundred ten into Two hundred sixty five milimeter) sizes respectively, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing 8 mm (Eight milimeter) dia C.P. / S.S. Jet with flexible tube upto 1 (One) metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved , including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :-100 mm (One hundred milimeter) inlet and 100 mm (One hundred milimeter) outlet :- Sand cast iron S&S as per IS: 3989, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing wash basin with C.I. brackets, 15 mm (Fifteen milimeter) C.P. brass pillar taps, 32 mm (Thirty two milimeter) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm (Five hundred fifty into Four hundred milimeter) with a pair of 15 mm (Fifteen milimeter) C.P. brass pillar taps, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-incharge (Note:- Butt hinges and necessary screws shall be paid separately) :-Kiln seasoned selected planks of sheesham wood :-35 mm (Thirty five milimeter) thick shutters (Swming), including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of (Kajaria, Nitco, Somany,Orient, RAK,Jonson & Jonson) make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm (Twelve milimeter) thick bed of cement mortar 1:3 (One cement isto Three coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm (Three point three kilogram per Square meter), including pointing in white cement mixed with pigment of matching shade complete, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Centering and shuttering including strutting, propping etc. and removal of form for : - Lintels, beams, plinth beams, girders, bressumers and cantilevers, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat with cement primer, including all leads, lifts and carriage of materials, complete in all respect of as per entire satisfaction of the Engineer in charge.