Public Works Department Tender

Construction of Subgrade and Earthen Shoulders Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 (Reference to MoRT&H's specification clause 305).

Construction of Shoulders B. Hard Shoulders Rate as applicable for sub-base and or base may be adopted as per approved design.

By Mix in Place Method Construction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401 Grading-III

By Mix in Place Method Construction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401 Grading-V

Providing and laying Filter material underneath pitching in slopes complete as per drawing and Technical specification Gradation of filter , Thickness of filter 200/300 mm (Reference to MORT&H's specification 2504).

Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400-13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406

Prime Coat Providing and applying primer coat with cationic bitumen emulsion MS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer using mechanical means (Reference to MORT&H's specification clause 502). On WMM surface @ 0.85 Kg /sqm.

Tack Coat Providing and applying tack coat with Cationic bitumen emulsion complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503). On bituminous surface @ 0.25 kg /sqm.

Dense Graded Bituminous Macadam Providing and laying dense graded bituminous macadam with 100-120 TPH batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder of approved grade @ 4.0% (min) for Grading -1 and 4.5% (min) for Grading -2 by weight of total mix and filler(Cement /hydrated lime /Rock dust ) as per table 500-10 and mix design done as per table 500-11and job mix formula as per clause 505.3.3 transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory tandem roller and with pneumatic tyre roller of 12 to 15 tonne weight with a pressure at least 0.56 MPa as directed by E-I-C, and to achieve the desired compaction as per MORT&H specification clause No. 505.3.5 complete in all respects (Reference to MORT&H's specification clause 505). For Grading 2 (26.5 mm nominal maximum aggregate size ) Layer Thickness 50-75 mm

Bituminous Concrete Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder of approved grade@ 5.2% (min) for Gr.-1 & @ 5.4% (min) for Gr.-2 , as per table 500-17, and mix design done as per table 500-10 and job mix formula as per cl. 505.3.3 and filler(Cement /hydrated lime /Rock dust ), transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory tandem roller and with pneumatic tyre roller of 12 to 15 tonne weight with a pressure at least 0.56 MPa as directed by E-I-C to achieve the desired compaction as per clause no 507.3.5 complete in all respects ref. to MORTH specification clause No.507. for Grading-2 ( 13.2 mm nominal maximum aggregate size), Layer thickness:30-40mm

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes (Reference to MORT&H's specification 803).

Road Markers/Road Stud with Lense Reflector Providing and fixing of road stud 100x 100 mm, die-cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors,installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973.

GST @18%(CGST 9.0%+SGST9.0%) of above