North Bengal Development Department Tender
... More
The NBDD has issued a formal invitation for competitive bids for the North Bengal Development Department project, for Repairing Work Of Bituminous Road From Jamtala More To Infront Of Phe Water Tank In The Premises Of Uttar Banga Krishi Viswavidyalaya Under Pundibari Gram Panchayat Within Cooch Behar-ii Block In The District Of Coochbehar (length 490.00 M , Width in Jalpaiguri, West Bengal, with an estimated contract value of Rs. 47,84,307. The bid opening date for this tender is 13-11-2026 and the last date for bid submission is 27-11-2026. Interested bidders for North Bengal Development Department tender can download the important documents here to check the scope of work, eligibility criteria and technical requirements.
North Bengal Development Department - NBDD Tender - WB Tender
Opening Date13 Nov 2026
Closing Date27 Nov 2026
Tender Amount₹ 47,84,307
Costs
EMD
₹ 95,686Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Repairing Work Of Bituminous Road From Jamtala More To Infront Of Phe Water Tank In The Premises Of Uttar Banga Krishi Viswavidyalaya Under Pundibari Gram Panchayat Within Cooch Behar-ii Block In The District Of Coochbehar (length 490.00 M , Width
Contact
Tender Id
2026_NBDD_1049078_13Tender No
NBDD/BS/EE/ NIe-T- 100/2026-27Tender Authority
North Bengal Development Department ViewPurchaser Address
-Website
https://wbtenders.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
Bituminous Macadam Providing and laying bituminous macadam using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction (Reference to MORT&H's specification clause 504).ii)for Grading 2 (19 mm nominal size)
96.47
15806
1524854.98
... More
Tack Coat Providing and applying tack coat with Cationic bitumen emulsion (RS1) complyingwith IS:8887using emulsion pressure distributor on the prepared bituminous/granular/cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503).i)On bituminous surface @ 0.20kg-0.3kg /sqm.
1929.38
30
59019.73
... More
Mastic Asphalt Providing and laying 25mmthick masticasphaltwearingcoursewith approved grade bitumen meeting the requirements given in table 500 39, prepared by using mastic cooker and laid to required level and slope after cleaning the surface, including providing antiskid surface with bitumen precoated fine-grained hard stone chipping of 13.2 mm nominal size at the rate of 0.005 cum per 10sqm and at an approximate spacing of 10 cm center to center in both directions, pressed into surface when the temperatureof surfaces isnotlessthan100°C,protruding1 mm to 4 mm over masticsurface, al lcomplete as per
clause 516(Reference to MORT&H's specification clause 516 alongwith IRC:107).
1929.38
1304
2517242.79
... More
Direction and Place Identification Signs with size more than0.9 sqm size Board. Providing and erecting direction and place identification retro reflectorised sign as per IRC :67 made of high intensity grade
sheeting vide clause 801.3, fixed over aluminium sheeting, 2mm thick with area exceeding 0.9 sqm supported on a mildsteel angle iron post 75mmx75mmx6mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M15grade cement concrete 45cmx 45cmx60cm, 60cm below ground level as per approved drawing (Reference to MORT&H's specification 801).
1.1
23676
26043.82
... More
Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5 mm
thick including reflectorising glass beads @ 250 gms per sqm area,thickness of 2.5mmis exclusiveof surface applied glass beads as per IRC:35 .The finished surface to be
level,uniformandfreefromstreaks and holes (Reference toMORT&H's specification 803).
98
734
72019.22

