Border Security Force Tender

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations & footing, base of column etc for mass concrete.

Providing and laying of position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All kind upto plinth level :

1:1.5:3 (1 Cement : 1.5 coarse sand (Zone -III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources.

Steel reinforcement for R.C.C work i/c straightening, cutting, bending, placing in position and binding all complete upto plinth level. a) Thermo-Mechanically Treated bars of grade Fe-500 D or more

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. a) Hot finished welded type tubes

Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

100 Amp, 16 KA, TPMCCB

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

3 x 1.5 sq. mm

Supplying and fixing 5 amps to 32 amps rating, 240 volts, 'C' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40 amps

63 amps

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

4 x 10 sq. mm (25 mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required

3.5 x 50 sq. mm (35 mm)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal)

Providing and erection of 7 Meter height octagonal type, in single section with single longitudinal weld & galvanized designed as per ILE TR7 & BS5649 for structural design & as per IS875 (Part III), 1987 amended up to date with following specifications : - Bottom dia 130 mm & top dia 70 mm, thichkness 3 mm as per technical specifications alongwith 1 Mtr long single arm standard bracket made of 48.3 OD of GI Pipe, suitable for the installation of 01 Nos LED fittings with base plate of 220 x 220 x 12 mm welded at the bottom and complete with with 4 Nos. 20 mm dia 700 mm long J type bolt with double nut systematically located for holding the pole and nuts & bolts washer for earthing, etc as required on site. (Bajaj / Utkarsh or equivalent make or as approved by Engg-Incharge).

Supplying and Installation of 60 Watt LED Street /security light on exising pole having system effecacy of 110/120 Lumen / Watt outdoor type of IP 66 with 10 KV SPD and made up of pressure die cast housing with toughened glass and high power LED with secondary optics, Colour tempature 6000 K, suitable with beam angle to meet desired illumination level as per required technical specifications i/c connections, interconnections, testing etc as per specification complete as required. (Make Crompton, Model - Cat No- CRP-409-60-57-SL-GL-NSG or equilent make & technical specifications.

S.I.T.C. of 10 Watt decorative Bollard light luminiries, IP 65 with pressure die cast Aluminium housing with PC diffuser & clear acrylic cover complete with auto adjutable 140 - 270 volts using the same driver foundation i/c connection with 1.5 sqmm FR PVC insulated copper conductor single core cable and etc as required. ( Make Crompton, Cat No-LBLA1-10-WW or equilent make & technical specifications.

Providing and fixing of 03 Mtr long GI Pole of 50 mm dia Class: B with 3.6 mm thickness confirming to IS-1161:2014 used for street lights pole, welded with GI base plate with dimension 300 mm X 300 mm X 5mm, Grouted in a concrete mixture of 1:2:4 (1 cement : 2 coarse sand (Zone-III) : 4 grade stone aggregate 20 mm nominal size) column, having depth 700 mm ( in which 200 mm will be projected above ground level) and dia of 300 mm (min) etc. complete as required.

Suppying and fixing of 40 Watt Decorative post top LED fitting with IP65 protection, resistant to impact and corrosion free and energy saving environmental friendly, clear Glass cover on existing GI Pole including connection & testing complete etc as spcifications & as reqd. (Havells /Crompton /Wipro/ Philips make)

Providing and fixing of 30 Watt white Solar LED light with LED chip efficiency 135 Lumen/watt, the colour temperature of white LED light will be between 5700 K to 6500 K, the temperature of heat sink should be 20° C above ambient temperature during operation, CRI 70%. Lighting quality: Free from glare, Flickering and UV, with motion sensor, Wattage - power consumption of the LED Luminaries/ lighting unit = 30 watt (including LED and driver power loss) and charge controller with ≤ 20 mA at rated voltage and rated current, with Indigenous module TEC tested Mono crystalline solar panel of 75 Wp and with maintenance free long life Lithium Ferro Phosphate battery (LiFePo4 ) 12.8V, 30 Ah at STC, with Battery cycle life of 2000 cycle at 80% discharge, to operate from dusk to dawn, IP 65 or better with corrossion resistant metallic frame structure having vandal resistance IK 06 and with suitable rated DC wire for connection. Provided with full protection against open circuit, accidental short circuit and for reverse polarity along with 2 LED indicators: a green light to indicate charging in progress and a red LED to indicate deep discharge condition of the battery. The green LED will glow only when the battery is actually being charged (Approved makes: UK Solar/Philips /GE/Wipro/Surya)

Providing and fixing of 06 Mtr long GI Pole of 65 mm dia Class: B with 3.6 mm thickness confirming to IS-1161:2014 used for street lights pole, welded with GI base plate with dimension 300mm X 300mm X 5mm, Grouted in a concrete mixture of 1:2:4 (1 cement : 2 coarse sand (Zone-III) : 4 grade stone aggregate 20 mm nominal size) column, having depth 1000mm ( in which 200 mm will be projected above ground level) and dia of 300 mm (min) etc. complete as required.

Providing and fixing of Digital Time Switch (Timer) 24 Hrs program ON-OFF steps and Min setting unit: 15 Minuts in existing panel suitable for single phase 230 V, 50 Hz product code - MTS4M-116 A-230 V-CE description DIN - Rail / Flush mount mechanically daily / weekly time switch, 16 A relay i/c connection etc as required. (L & T / Legrand / Havells or its equivelent make)

SITC of various sizes water protected outdoor type (water proof) hut type compartmentalized type double door 02 Nos panels, both side opening with 450 mm depth suitable for 415 V, 3 phases, 50 Hz made out of 2 mm thick CRCA sheet with required hardware duly painted with power coated. The panel having separate detachable gland plate angle iron base frame made out of 50 mm x 50 mm x 5 mm angle iron of suitable size of the feeder pillar (minimum height 1200 cm), hinged door, both side opening with locking arrangement, earth bar /stud, LED pilot light for phase indicator (R,Y,B) on top, 200A/415V 4 strip aluminum bus bar duly PVC sleeved, connection inter-connection with 25% extra current carrying capacity solid aluminium rod /solid copper conductor cable 10 sqmm/ for incoming/Outgoing cables, links /heavy duty connectors/ terminals for three and single phase cable connections and suitable rail chanel for TP/DP/SP Isolators/MCB including marking of location for incoming and out going distribution i/c grouting the legs in existing floor with 1.3.6 cement concrete foundation, incoming/outgoing cable connections etc as required.

Providing and laying one number of PVC insulated aluminium Conductor un-armourd cable of following size in the existing HDPE /HUME/ METAL/DWC pipe as required.

2x10 sqmm

Providing and laying one number of PVC Sheathed PVC insulated XLPE aluminium Conductor armourd cable of following size in the existing HDPE /HUME/ METAL/DWC pipe as required. The cable should conform to IS 7098 (Part1) 1988 with upto date amendents if any.

4x10 sqmm

Providing and laying one number of PVC Sheathed PVC insulated XLPE aluminium Conductor armourd cable of following size in the existing HDPE /HUME/ METAL/DWC pipe as required. The cable should conform to IS 7098 (Part1) 1988 with upto date amendents if any.

3.5x50 sqmm

Supplying, laying and fixing of following size HDPE pipe ISI marked conforming to IS 4984, in the existing trench / pole collar for proctection of cable complete as required. A) 32 mm

Providing and fixing of 60 Watt Solar with lumen efficacy ≥ 130 lumen/watt, CRI ≥ 70, CCT 5700K, IP 65 complied with IS: 10322 (Part5/Sec5) with suitable charge controller/MPPT fitted in Aluminium housing, powered with Lithium Pero phosphate (LiP04) battery 12.8V/54 Ah placed in suitable GI battery Box (IP 55) and suitable Mono Crystalline Solar Module with 'anti-reflective, anti-soiling, anti-abrasive and hydrophilic coating' offered with 5 years of warranty and 25 years of performance warranty and complied with latest MNRE specifications fitted to existing pole with suitable bracket and clamps, connections with suitable rated insulated copper conductor etc. as required. The solar light must have 2 days autonomy (dusk to dawn full with bright) with automatic on/off control and wide beam angle to meet desired illumination level as per technical specifications and site requirement.

Providing and fixing of 195 mm x 135 mm x 90 mm HOT press moulded SMC looping box with hinged front cover having locking arrangement complete with earth stud, one MS clamp of the 40 mm x 6 mm section, nut and bolt for fixing looping box to the pole including providing and fixing following accessories and interconnection etc as reqd (i) SP MCB 10 amps -01 No (ii) 4 way terminal block (Sintex or its equivelent specifications make)