Bridge Ropeway Tunnel And Other Infrastructure Development Corporation Of Uttarakhand Limited Tender
View complete overview of Uttarakhand BRIDCUL Tender
Bridge Ropeway Tunnel And Other Infrastructure Development Corporation Of Uttarakhand Limited - BRIDCUL Tender
Civil And Construction
Building Construction
Eprocure
Opening Date17 Feb 2025
Closing Date3 Mar 2025
Tender Amount₹ 3,08,40,000
Technical
Technical
Financial
Class Of Bidder
... View More
Category-II (2 to 5Cr.) for Contractors Empanelled in Civil work.
Bid Capacity
... View More
The bid capacity required can be calculated using the formula: Assessed Available Bid Capacity = (A*N*2-B) Where A= Maximum value of Construction work with or without Electrical works executed in any one year during the last five years, N= Number of years prescribed for completion of the works for which bids are invited. B=Value of existing commitments and on-going works to be completed during the next one. Alternatively, the bid capacity required is also mentioned as 20% of the contract value or 20% of the estimated cost. Additionally, the bid capacity required can be summarized as: - 25% of the tender value: Rs. 77.10 Lac
- Liquid assets and/or credit facilities: Rs. 61.68 Lac (20% of the estimated cost) The bid capacity required can also be calculated as: Bid Capacity = 0.2 * Estimated Cost Or Bid Capacity = 20% of Estimated Cost. However, another formula for calculating the Balance Bid Capacity is mentioned but not provided in the given text. Therefore, multiple formulas and values are provided for calculating the bid capacity required.
Technical Capacity
... View More
The bidder should have satisfactorily completed at least one similar work worth 35% of the Tender value, i.e., Rs. 107.94 Lac, or at least two similar works worth 25% each of the tender value, i.e., Rs. 77.10 Lac, in the last five years prior to the Bid Submission deadline. The value of the experience submitted by the bidder shall be indexed as per the given escalation factors for each year. The bidder should also have completed 25% of the estimated cost of major items of civil works in a single project executed in the last five years. Additionally, the bidder should have liquid assets and/or availability of credit facilities not less than 20% of the estimated cost, which is Rs. 61.68 Lac. The bidder should be registered in BRIDCUL for civil works in Category-II (2 to 5 Cr). The bidder is required to have prior work experience in civil engineering, with specific details to be provided in the Qualification Information section, including the total value of civil engineering work performed in the last five years, with a breakdown of the cost of projects for each year. The bidder must also provide details of similar works performed as a prime contractor over the last five years, including project name, employer, description of work, contract value, and completion period. The bidder must provide quantities of related items of similar works executed as a prime contractor or through a nominated sub-contractor over the last five years, with details on the amount of work performed and remarks. The bidder must submit a certificate from a Chartered Accountant for the total value of related engineering construction work performed in the last five years, and an audited turnover certificate for the last five financial years, with a breakup of related civil works in each financial year.
Costs
EMD
₹ 6,17,000Document Cost
₹ 5,900Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2025_BRID3_80392_1Bid Award Id
ViewTender No
2902/BRIDCUL/233/25 Dated 06.02.2025Tender Authority
Bridge Ropeway Tunnel And Other Infrastructure Development Corporation Of Uttarakhand Limited ViewPurchaser Address
-Website
http://http://bridcul.com/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
... More
Extra for every additional lift of 1 . 5 m or part thereof in excavation I banking excavated or stacked materials.
All kinds of soil
339.61
-
-
... More
Extra for every additional lift of 1 . 5 m or part thereof in excavation I banking excavated or stacked materials.
Ordinary or hard rock
84.89
-
-
... More
Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
1835.16
-
-
... More
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1 :4:8 (1 cement : 4 coarse sand (zone-Ill) derived from natural sources : 8 graded stone aggregate 20 mm nominal size derived from natural sources)
12.16
-
-
... More
Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete
149.93
-
-
... More
Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
1016.61
-
-
... More
Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform
572.45
-
-
... More
Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers
417.13
-
-
... More
Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts
376.3
-
-
... More
Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases
-
-
-
... More
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
43720.12
-
-
... More
Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana I Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.:
Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.
All works upto plinth level
Concrete of M25 grade with minimum cement
content of 330 kg /cum
287.48
-
-
... More
Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana I Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.:
Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.
All works above plinth level upto floor V level
Concrete of M25 grade with minimum cement
content of 330 kg /cum
136.32
-
-
... More
Add for using extra cement in the items of design mix over and above the specified cement content therein.
169.53
-
-
... More
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1 :6 (1 cement: 6 coarse sand)
62.04
-
-
... More
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1 :4 (1 cement :4 coarse sand)
128.46
-
-
... More
Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half brick masonry.
128.46
-
-
... More
Extra for forming cavity 5 cm to 11.5 cm wide in cavity walls with necessary weep and vent holes including use of cores and cost of providing and fixing bitumastic coated M .S. ties 300 mm long of 25x3 mm section at not less than 3 ties per sqm as per approved design.
42.84
-
-
... More
Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1 :6:12 (1 cement: 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1 :6 (1 cement: 6 coarse sand)
97.19
-
-
... More
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 :4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm
91.61
-
-
... More
Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work
636.72
-
-
... More
Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.
636.72
-
-
... More
Providing and fixing cramps of required size & shape in RCC/ CC I Brick masonry backing with cement mortar 1 :2 ( 1 cement :2 coarse sand), including drilling necessary hole in stones and embedding the cramp in the hole (fastener to be paid separately). Stainless steel cramps
1258.2
-
-
... More
Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete.
Fastener with threaded dia 6 mm
12582
-
-
... More
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood
1.5
-
-
... More
Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. Sal wood
8.82
-
-
... More
Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: Butt hinges and necessary screws shall be paid separately) Second class teak wood 35 mm thick shutters
53.25
-
-
... More
Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Second class teak wood
11.44
-
-
... More
Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Float glass panes 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).
17.52
-
-
... More
Extra for providing frosted glass panes 4 mm thick (weight not less than 1 0 kg per sqm) instead of ordinary float glass panes 4 mm thick (weight not less than 1 0 kg per sqm) in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).
6
-
-
... More
Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I ) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws
12.61
-
-
... More
Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).
12.61
-
-
... More
Providing and fixing wire gauge shutters using galvanized M.S. wiregauge of average width of aperture 1 . 4 mm in both directions with wireof dia 0.63 mm, for doors, windows and clerestory windows with hingesand necessary screws : 35 mm thick shutters with ISi marked M.S. pressed butt hingesbright finished of required size Second class teak wood
21.96
-
-
... More
Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm, 1 :3:6 mix (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).
166
-
-
... More
Providing & Fixing decorative high pressure laminated sheet of plain I wood grain in gloss/matt/suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick
25.2
-
-
... More
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes
2946.71
-
-
... More
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement: 4 coarse sand): 25 mm thick
102.04
-
-
... More
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 1 2 mm (average) thick cement mortar 1 :3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
16.81
-
-
... More
Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.
45.2
-
-
... More
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1 :4 (1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
172.78
-
-
... More
Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I . S . 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 1 2 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.
Size of Tile 600x600 mm (300x600 mm)
122.32
-
-
... More
Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
18.9
-
-
... More
Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.
96.8
-
-
... More
12 mm cement plaster of mix : 1:6(1 cement: 6 fine sand)
530.18
-
-
... More
6 mm cement plaster of mix : 1:3(1 cement: 3 fine sand)
173.96
-
-
... More
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm
541.22
-
-
... More
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
117.74
-
-
... More
French spirit polishing :
Two or more coats on new works including a coat of wood filler
789.18
-
-
... More
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
541.22
-
-
... More
Painting (one or more coats) with black Japan paint of approved brand and manufacture to give an even shade.
19.89
-
-
... More
Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete.
344.41
-
-
... More
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
8
-
-
... More
Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :
(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.
(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.
The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
24.32
-
-
... More
Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :
(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.
(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.
The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
460.74
-
-
... More
Stone work (machine cut edges) for wall lining etc. upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : Regional stone - exposed face fine dressed with rough backing 50 mm thick ( 450mm x 200mm) (Wall Cladding Stone)
566.22
-
-
... More
Providing and fixing brass handles with screws etc. complete:
Pull handle
Model no-VISH GS
Size 200 mm,
78
-
-
... More
Providing and fixing brass handles with screws etc. complete:
Pull handle
Model no-VISH AB
Size 100 mm
20
-
-
... More
Providing and fixing brass tower bolts (barrel type) with necessary screws etc. complete
Model no- VX Size (200x12) mm
66
-
-
... More
Providing and fixing brass tower bolts (barrel type) with necessary screws etc. complete
Model no- VX Size (150x12)mm,
30
-
-
... More
Providing and fixing bright finished brass 250 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete
Model No-Lever Handle Tango CY with Lock body and cylinder 60mm OSK
7
-
-
... More
Providing and fixing bright finished brass mortice latch and a pair of lever handles of approved quality with necessary screws etc. complete
Model No-
Lever Handle Tango DY with BL-3 Latch for bathroom
8
-
-
... More
Providing and fixing brass butt hinges with necessary screws etc. complete : Size (100x75x3) mm,
40
-
-
... More
Providing and fixing brass butt hinges with necessary screws etc. complete : Size (125x75x4) mm,
168
-
-
... More
Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
Brass casement stays (straight peg type ) 200 mm weighing not less than 0.24 kg
Size 150 mm
18
-
-
... More
Providing and fixing brass hanging type floor door stopper with necessary screws, etc. complete.
Model No- DS 02
Size: 140 mm
28
-
-
... More
Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body,door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Aluminium extruded section body tubular type universal hydraulic door closer DC 80 PDC
11
-
-
... More
Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required
colour or shade, with nuts and screws etc. complete : Sliding Bolt (300x16) mm, EX-02
12
-
-
... More
Providing and fixing second class deodar wood hand rail having size of 75 mm x 65 mm with approved decorative shape etc.
31.5
-
-
... More
Providing and fixing Deodar Wood Jhalar (Manually Hand Carved) in 25 mm thick 300 mm wide deodar wood plank.
40.17
-
-
... More
Providing, laying and fixing of Deodar Wood as in built runner having size of 100mmX70 mm through out over masonary course during construction of wall as per detail drawing. It allows to apply adhesive on top and bottom of wood surface with additional fixing accessories of GI nut & bolt/ anchor fastners, nails, screws etc. to masonary work or provided RCC runner to protect against demormation with all due respect to complete the job. It allows providing and applying minimum two coats of approved water base PU polishing complete with required primer / sealer coat, rubbing, sand papering, powdering, etc. to exposed surface complete as per manufacturer specification.
451.4
-
-
... More
Providing and fixing Teak Wood ceiling in 25 mm thick 150 mm wide teak wood plank.
408.76
-
-
... More
Providing and fixing 2nd class deodar wood plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface.25mm thick
29.95
-
-
... More
Two or more coats on new works including a coat of wood filler Hydro Oil For Exterior Coating
109.13
-
-
... More
Providing and fixing Himachali Stone Slate(Pathaal)-15mm thick of uniform colour and size (450MM x 300MM) , for RCC Sloped Roof backing filled with a grout of 12mm thick cement mortar 1:3 (1Cement : 3 Coarse Sand) & jointed with Cement mortar 1:2(1Cement :2 Stone dust), including grinding with hand grinder on joints, rubbing and polishing complete. (To be secured to the backing and the sides by means of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge.Himachali Stone Slate(Pathaal)-15mm thick
479.17
-
-
... More
Providing and fixing wash down wall mounting EWC-P of approved shade, conforming to Pattern 2 of IS: 2556 (Part -II), with pipe and plug bend as per specifications; glazed vitreous / Coloured European Water Closet with metropole flush valve, with grouting the CI chair in side the floor/wall, rubber gaskets, connecting PVC 110mm dia soil pipe with PVC coupling, nuts, mounting cistern on WC.,1 No.CPVC connection with brass union nuts CP coated and solid verity heavy duty plastic seat cover as per IS-2548, of approved make; including painting of fittings and brackets, cutting and making good the walls wherever require: etc. complete. The rates including cost and conveyence of all materials, labour, machinery etc.
EWC-P with Soft close Seat cover : Jaquar, Model No: CNS-WHT-959SPP
Metropole flush valve Dual flow : Jaquar, Model No: FLV-1085NG
8
-
-
... More
Providing and fixing of 3 in 1 wall mixer system with provision for overhead shower complete with bend pipe including necessary fittings with wall flange etc complete in all respects including cutting and making good the walls etc. SHOWER HEAD: Jaquar MODEL NO. OHS-CHR-1789
SHOWER ARM Jaquar MODEL NO. SHA-487
WALL MIXER Jaquar MODEL NO. FUS-29273UPR
6
-
-
... More
Providing and fixing White glazed vitreous Wash Basin Oval Under-Counter, size 560 x 430 x 195 mm dia., with supporting M.S. or C.I. Brackets, necessary pipe connection up to the outside face of the wall, having Telephonic Black / Colour Granite of 180 mm thick fixed on Black Kadappa Framework, Waste coupling 32 mm size full thread with 80 mm height Chrome plated, Bottle trap Chrome plated Basin Mixer necessary fittings with wall Flange etc. complete in all respects including cutting and making good the walls etc. OVAL UNDER COUNTER BASIN: Jaquar , Model No: FLS-WHT-5701
WASTE COUPLING : Jaquar , Model No: ALD-CHR-705
BOTTLE TRAP : Jaquar , Model No: ALD-769L300X190
Basin Mixer: Jaquar , Model No: FLR-5001B
8
-
-
... More
Providing and fixing 15mm C.P. brass angle valve with C.P. copper connecting pipe 450 mm long and nuts, washer and brass flange complete, including cutting and making good the wall where required. ANGLE VALVE : Jaquar, Model No. FLR-5053N
BRAIDED HOSE Copper Pipe : Jaquar, Model no. ALD-CHR-805B
40
-
-
... More
Providing and fixing of Hand Shower (Health Faucet), with 8mm Dia,1.2 Rmt Long pvc Tube and Wall Hook accessories of best quality necessary fittings with wall Flange etc. complete in all respects including cutting and making good the walls etc. HAND SHOWER : Jaquar , Model No: ALD-573
8
-
-
... More
Providing and fixing in position best Indian make toilet recessed type paper holder complete in all respects including cutting and making good the walls etc. TOILET PAPER HOLDER : Jaquar , Model No: AHS-1553
8
-
-
... More
Providing & fixing C.P. brass towel ring fixed to rawl plug with C.P. brass screws.
TOWEL RING : Jaquar Continental, Model No.: ACN-1121BN
6
-
-
... More
Providing and fixing C.P. brass liquid soap container of best quality. LIQUID SOAP CONTAINER: Jaquar , Model No: SDR-WHT-DJ0010F
8
-
-
... More
Providing and fixing in position best Indian make C.P. brass twin way QUOTE and hat hooks fixed into wall with C.P. Brass screws and rawlplugs etc. complete including cutting and making good the walls etc.
DOUBLE QUOTE HOOKS: Jaquar, Model No: -ACN-1161N
8
-
-
... More
Providing and fixing of electrical type water Geyser inclusing all required accessories cutting, chassing and good the same.
25 Litre Storage, Make: Jaquar Elena vertical
6
-
-
... More
Providing and fixing of electrical Instant type water Geyser inclusing all required accessories cutting, chassing and good the same.
3 Litre Insta, Make: Jaquar Insta
2
-
-
... More
Electrical hand dryer, fully automatic type , cover shall be fabricated in extra heavy duty18 gauge type 304 SS with exposed surfaces satin finished, the unit shall deliver not less than 71 l/sec of hot air and electrical rating shall be 240 V / 1 phase / 50 cycles HAND DRYER : Jaquar , Model No: HDR-SSF-AK2803D
8
-
-
... More
Providing and fixing perfume dispenser fixed to wooden cleats with C.P. brass screws complete. Air Purifier: Euronics , Model No: EA-33
8
-
-
... More
Providing and fixing in position 15 mm C.P. brass bib cocks of best quality necessary fittings with wall Flange etc. complete in all respects including cutting and making good the walls etc.
BIB COCK : Jaquar Fusion , Model No. FUS-29037
8
-
-
... More
Providing & fixing towel rail of approved make including, providing & fixing C.P. brass screws, making holes in walls & making good. TOWELRAIL: Jaquar Continental, Model No. ACN-1111SM
6
-
-
... More
Fixing stainless steel recessed type soap dish of approved make. Including providing & fixing screws, washers, cutting & making good the walls.
SOAP DISH : Jaquar, Model No: AKP-35731P
6
-
-
... More
Providing, installation, testing and commissioning of 50 mm dia. Acoustic Multilayer Polyproplene pipe conforming to BS EN 1451-Part 1-6 with 3 layer pipe made of PP + PP-MD + PP and one layer fittings in PP MD, Push fit/ Ring fit type, Halogen and Cadmium free, having high impact resistance as per DIN EN ISO 291:2008-08, Fire resistancy DIN 4102 B2, Ring stiffness SN6 6KN/m2 as per ISO 9969, offering sound levels of 21 dBA as per EN 14366 at a flow rate of 4 l/s, water tightness as per EN 1451-1 minimum of 0.5 bar for 15 minutes, density of pipe = 1.15to1.25 gms/cm3, elongation = 0.09mm/mn/K and E modulus 2300-3000 as per ISO 178, along with factory fitted EPDM lip ring, Fire Behavior Classification according to EN 13501-1:2009 & classified D-s2-d2 (EN 13501-1), meets the requirements of EN 4102-2 with Fire Classification B2, Smoke Development Category Q1 & Drip Formation category TR1.
The scope shall be Including all fittings such as bends, junctions, inspection doors, offsets, cowl, access pieces/plugs, fixing waste pipes to the floor with concrete bedding for full length etc. including cutting holes in walls, slab and beam, chasing the wall by grinder cutter, including all the engineered support (support, hanger, nuts/bolts, anchor fasteners, fixing clamp/ channels with U-bolts, etc) as per detail technical specification etc. complete the job and making good the same etc. complete the job as directed by Engineer in charge.
(Soil, Waste & Vent Pipe)
17
-
-
... More
Providing, installation, testing and commissioning of 75 mm dia. Acoustic Multilayer Polyproplene pipe conforming to BS EN 1451-Part 1-6 with 3 layer pipe made of PP + PP-MD + PP and one layer fittings in PP MD, Push fit/ Ring fit type, Halogen and Cadmium free, having high impact resistance as per DIN EN ISO 291:2008-08, Fire resistancy DIN 4102 B2, Ring stiffness SN6 6KN/m2 as per ISO 9969, offering sound levels of 21 dBA as per EN 14366 at a flow rate of 4 l/s, water tightness as per EN 1451-1 minimum of 0.5 bar for 15 minutes, density of pipe = 1.15to1.25 gms/cm3, elongation = 0.09mm/mn/K and E modulus 2300-3000 as per ISO 178, along with factory fitted EPDM lip ring, Fire Behavior Classification according to EN 13501-1:2009 & classified D-s2-d2 (EN 13501-1), meets the requirements of EN 4102-2 with Fire Classification B2, Smoke Development Category Q1 & Drip Formation category TR1.
The scope shall be Including all fittings such as bends, junctions, inspection doors, offsets, cowl, access pieces/plugs, fixing waste pipes to the floor with concrete bedding for full length etc. including cutting holes in walls, slab and beam, chasing the wall by grinder cutter, including all the engineered support (support, hanger, nuts/bolts, anchor fasteners, fixing clamp/ channels with U-bolts, etc) as per detail technical specification etc. complete the job and making good the same etc. complete the job as directed by Engineer in charge.
(Soil, Waste & Vent Pipe)
17
-
-
... More
Providing, installation, testing and commissioning of 110 mm dia. Acoustic Multilayer Polyproplene pipe conforming to BS EN 1451-Part 1-6 with 3 layer pipe made of PP + PP-MD + PP and one layer fittings in PP MD, Push fit/ Ring fit type, Halogen and Cadmium free, having high impact resistance as per DIN EN ISO 291:2008-08, Fire resistancy DIN 4102 B2, Ring stiffness SN6 6KN/m2 as per ISO 9969, offering sound levels of 21 dBA as per EN 14366 at a flow rate of 4 l/s, water tightness as per EN 1451-1 minimum of 0.5 bar for 15 minutes, density of pipe = 1.15to1.25 gms/cm3, elongation = 0.09mm/mn/K and E modulus 2300-3000 as per ISO 178, along with factory fitted EPDM lip ring, Fire Behavior Classification according to EN 13501-1:2009 & classified D-s2-d2 (EN 13501-1), meets the requirements of EN 4102-2 with Fire Classification B2, Smoke Development Category Q1 & Drip Formation category TR1.
The scope shall be Including all fittings such as bends, junctions, inspection doors, offsets, cowl, access pieces/plugs etc. including cutting holes in walls, slab and beam, chasing the wall by grinder cutter, including all the engineered support (support, hanger, nuts/bolts, anchor fasteners, fixing clamp/ channels with U-bolts, etc) as per detail technical specification etc. complete the job and making good the same etc. complete the job as directed by Engineer in charge.
The scope shall be also include Providing and laying 100mm thickness cement concrete 1:5:10 (1 cement : 5 coarse sand :10 graded stone aggregate 40 mm nominal size) around the pipe etc. complete the job as directed by Engineer in charge.
(Soil, Waste & Vent Pipe))
75
-
-
... More
Supply, installation, testing and commissioning of Polypropylene (PP) 110mm x 110mm size P trap with necessary of self cleaning design with water seal with and without vent arm jointing with push fit rubber ring socket fittings complete, as required height riser for basin/ sink/ Urinal drain connection with necessary distance piece of pipe, inlet hopper with two or three inlets fittings to receive waste pipes from fixtures waste and hopper shall be Manufactured from 110 mm dia. up to 600 mm long, etc., cutting chases/ hole in floors/ slabs and bringing the same in proper condition and shape after placing the trap in right position in case of suspended/ open plumbing or setting the trap in 1:2:4 CC in case of concealed plumbing, etc. complete the job as directed by Engineer in charge.
19
-
-
... More
Providing and fixing PTMT grating of Rectangular type with openable circular lid of 150mm nominal size square 100 mm diameter of the inner hinged round grating of approved quality and colour.
19
-
-
... More
Providing and fixing of 20 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge.
Concealed work,including cutting chases and making good the wall etc.
105
-
-
... More
Providing and fixing of 25 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chases and making good the wall etc.
20
-
-
... More
Providing and fixing of 32 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chases and making good the wall etc.
15
-
-
... More
Providing and fixing of 40 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chases and making good the wall etc.
35
-
-
... More
Providing and fixing of 50 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chases and making good the wall etc.
5
-
-
... More
Providing and fixing of 63 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chases and making good the wall etc.
-
-
-
... More
Providing and fixing of 20 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineerin- Charge. Internal Exposed on walls
30
-
-
... More
Providing and fixing of 25 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineerin- Charge. Internal Exposed on walls
22
-
-
... More
Providing and fixing of 32 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineerin- Charge. Internal Exposed on walls
70
-
-
... More
Providing and fixing of 40 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineerin- Charge. Internal Exposed on walls
45
-
-
... More
Providing and fixing of 50 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineerin- Charge. Internal Exposed on walls
20
-
-
... More
Providing and fixing of 63 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineerin- Charge. Internal Exposed on walls
30
-
-
... More
Providing and fixing of 75 mm Outer dia 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineerin- Charge. Internal Exposed on walls
-
-
-
... More
Providing and fixing 9 mm thick preformed syntheic rubber polymeric compound prefromed sleeves with all accessories & clamp, support , etc. (Inside Toilet) for 20 dia pipe
105
-
-
... More
Providing and fixing 9 mm thick preformed syntheic rubber polymeric compound prefromed sleeves with all accessories & clamp, support , etc. (Inside Toilet) for 25 dia pipe
20
-
-
... More
Providing and fixing 9 mm thick preformed syntheic rubber polymeric compound prefromed sleeves with all accessories & clamp, support , etc. (Inside Toilet) for 32 dia pipe
15
-
-
... More
Providing and fixing 9 mm thick preformed syntheic rubber polymeric compound prefromed sleeves with all accessories & clamp, support , etc. (Inside Toilet) for 40 dia pipe
35
-
-
... More
Providing and fixing 9 mm thick preformed syntheic rubber polymeric compound prefromed sleeves with all accessories & clamp, support , etc. (Inside Toilet) for 50 dia pipe
5
-
-
... More
Providing and fixing 9 mm thick preformed syntheic rubber polymeric compound prefromed sleeves with all accessories & clamp, support , etc. (Inside Toilet) for 65 dia pipe
30
-
-
... More
Supplying, laying/ fixing, testing and commissioning of following 50mm thickness resin bonded fiber glass pipe section insulation having density 80 kg/cum or mineral wool (non combustible) having density of 144 Kg/ cu m duly covered with a layer of 120 gm/sqm polythene sheet (vapour barrier) on pipe and finally applying 0.63mm aluminium sheet cladding complete with type3 , grade 1 roofing feltstrip(as per IS:1322 as amended up to date ) at joints etc. as per specifications and as required.
25
-
-
... More
Providing and fixing of 20mm diameter gun metal gate valve with C.I. wheel of approved quality
6
-
-
... More
Providing and fixing of 25mm diameter gun metal gate valve with C.I. wheel of approved quality
4
-
-
... More
Providing and fixing of 32mm diameter gun metal gate valve with C.I. wheel of approved quality
6
-
-
... More
Providing and fixing of 40mm diameter gun metal gate valve with C.I. wheel of approved quality
6
-
-
... More
Supplying, fixing, testing and commissioning of 50mm diameter butterfly valve (manual) with C I body SS Disc, Nitrile Rubber Seal & Oring PN 16 pressure rating as specified.
3
-
-
... More
Supplying, fixing, testing and commissioning of 65mm diameter butterfly valve (manual) with C I body SS Disc, Nitrile Rubber Seal & Oring PN 16 pressure rating as specified.
4
-
-
... More
Providing and fixing of 50mm diameter gun metal non- return valve (vertical) of approved quality
2
-
-
... More
Providing and fixing non-return valve of 65 mm dia with dual plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating as specified.
4
-
-
... More
Supply, Installation, Testing and Commissioning of 25 mm dia. air release valve.
6
-
-
... More
Providing and fixing 25mm dia float valve with pressure type PTMT float valve.
(Make: Prayag)
3
-
-
... More
Providing and fixing mosquito proof stainless steel overflow grating for tanks.( Zoloto/ Audco/ R.B./ Spirex)
3
-
-
... More
Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.
1250
-
-
... More
Supplying and fixing 50mm thick aluminium foil faced resin bonded fibre glass insulation (for polyethylene water storage tank) of density 24 kg/cu.m or mineral wool insulation(non combustible) of density 44 kg/cum after applying two coats of cold setting adhesive (CPRX compound) sealing all joints with self adhesive aluminium tape & covering with 0.63mmx19mm GI wire mesh netting & butting all joints and laced with GI wire complete and finally covered with one layer of tar felt stuck with hot bitumen as per specifications and as required. (for outdoor applications)
22
-
-
... More
Supplying, fitting & fixing of 50mm dia Pressure Reducing Valve set of approved make & best quality having by-pass valve arrangement including of 3 nos isolation valve.
1
-
-
... More
Supplying, fitting & fixing of 65mm dia Pressure Reducing Valve set of approved make & best quality having by-pass valve arrangement including of 3 nos isolation valve.
2
-
-
... More
6 Kg ABC (Powder Type) Fire Extinguisher. In HP Mild Steel Cylinders ISI marked fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully charged with ABC powder (Mono Ammonium Phosphate) pressured by Nitrogen complete in all respects including wall suspension bracket and conforming to IS:15683
Providing & Fixing of fire extinguishers with necessary accessories, stand, trolley, etc.
3
-
-
... More
ISI Marked portable fire extinguisher, 4.5 kg CO2 type fire extinguishers complete in all respect including initial fill and wall suspension brackets & shall conform to IS 2878
Providing & Fixing of fire extinguishers with necessary accessories, stand, trolley, etc.
3
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements