Cane Development And Sugar Industry Tender

DSR-Item-13.80- Proving and applying white cement based putty of average thickness 1 mm, of approved brand and manufacture , over the plastered wall surface to prepare the surface even and smooth complete .

DSR-Item13.41-Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :13.41.1 New Work (two or more coats) over and including water thinable priming coat with cement primer.

DSR Item 15.3 is a description of the work of demolishing reinforced concrete (RCC) manually or mechanically, including the stacking of steel bars and disposal of unserviceable material within a 50 meter lead. The work must be done as per the directions of the Engineer-in-charge

dismentalling of roofing including ridges, hips ,vallies …..........................DSR 15.28.2@ 77.30/sqm

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required DSR 12.50 @ 738.65/SQM

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:- Cement mortar 1:6 (1 cement : 6 coarse sand) @ 9105.95/cum

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

DSR-Item13.47- Finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade : 13.47.1 New Work (Two or more coats applied @ 1.43 ltr/10sqm over and including priming coat of exterior primer applied @ 2.20 Kg/10 sqm).

DSR-Item-13.99 Painting with synthetic enamel paint of approved brand and manufacture of required colourto give an even shade : One or more coats. On Old Work.

DSR-Item-14.10 Refixing old glass panes with putty and nails

SOR-Item- As in item 730 but for 730B above but with PVC pipe (Kisan, Spreme or equivalent) 6 kg/sqm . Pressure 10 Cm. Dia (Water rain pipes)

Electric Work in damage switch board, MCB, Tubelight and electrical completion

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 9.48.1 Fixed to steel windows by welding DSR 9.48.1 window

"Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angles 40x40x6 mm for diagonal braces sqm 5804.35 DSR 10.5.1

" Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1 40 mm thick with 20 mm nominal size stone aggregate sqm 614.20 DSR 11.3

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378)2 250x16 mm each 193.70 DSR 9.62.2

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378) 9.63.1 250x10 mm each 83.90 9.63.2 200x10 mm each 69.40 9.63.3 150x10 mm each 59.45 "* DSR9.63.1 250x10mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378) 9.66.1 125 mm each 39.95 9.66.1 each 29.70. DSR 9.66.1

"Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) cum 9045.7DSR 5.1.2

" Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) cum 7370.65 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 7132.25." DSR 6.1.2

TMT Fe-500 or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. DSR 5.22.6

10.25 Steel work welded in built-up sections/framed work, including cutting, hoisting, fixing in position, and applying a priming coat of approved steel primer using structural steel, etc., as required.dsr 10.25.2 10.25.1 In stringers, treads, landings, etc., of staircases, including use of chequered plate wherever required, all complete. Weight: