Telangana State Industrial Infrastructure Corporation Limited Tender

Filling with carted gravel in trenches,sides of foundations and basement with initial lead in layers not exceeding 15cm thick,watering and ramming including cost and conveyance of water to work site and all operaitonal,incidental, labour charges,hire charges of T&P etc., and overheads & contractors profit, all taxes except GST complete & Seignirage charges, for fnished item of work(APSS NO.309&310)

Providing Antitermite treatment as per IS 6315 (Part - 2) 2001 (Pre-constructional chemical treatment measures) along the internal & external vertical faces of the columns, plinth beams, basement and top surface of the basement filling below flooring bed as per the specified procedure conforming to IS 6315 (Part-2) 2001 and other relevant approved specification duly using Chlorpyriphos/ Lindane emulsifiable concentrate 20% with 1% concentration @ 7.5 Liters/ sqm of the vertical surface & @ 5.0 Liters/ sqm of the horizontal surface of the substructure to a depth of 500 mm around columns & 300 mm deep around plinth beams, basements & floor filling area including excavation channel along the wall & rodding etc & cost & conveyance of all materials to the site, cost of labour for spraying, rodding etc complete ,all taxes except GST for finished item of work directed by the Engineer-in-Charge

Plain Cement Concrete (1:4:8) (cement: fine aggregate: Coarse aggregate) for foundations and under flooring bed using fine aggregate { 50% of River Sand (Natural Sand) & 50% of Manufactured Sand/Crushed stone sand/Rock sand 4.75mm to 2.36 mm confirming to IS 383 } and coarse aggregate 40mm size hard broken , machine crushed granite metal from approved quarry including cost and conveyance of all materials like cement, & fine aggregate { River Sand (Natural Sand) & Manufactured Sand/Crushed stone sand/Rock sand } , coarse aggregate, water etc. to site, sales and other taxes except GST & seigniorage charges on all materials , but including all charges for machine mixing, laying concrete in foundations and under flooring bed, ramming in layers not more than 15cm thickness finishing top surface to the required level curing etc.,including overheads & contractors profit, complete for finished item of work. (APSS No. 402)

Providing plinth protection alround the building for total width of 1.20 M from basement including drain with 25mm thick top layer in CC 1:2:4 using 10mm nominal size well graded HBG chips, 100mm CC (1:4:8) bed using 40mm HBG metal laid over 100mm thick layer of stone crushed dust bed and top surfaces finished neatly with cement slury, providing brick masonry in CM(1:4) drain of 100mm thick wall using fly ash bricks for wall with clear opening of 230mm and depth not less than 200mm with proper gradient etc., complete. including cost and conveyance of of all materials like cement, coarse aggregate, fine aggregate { 50% of River Sand (Natural Sand) & 50% of Manufactured Sand/Crushed stone sand/Rock sand 4.75mm to 2.36 mm confirming to IS 383 }, etc., to site, including machine mixing, laying concrete, finishing smooth to required levels, curing, all other incidental and operational charges, labour charges etc., including all taxes except GST & Segniorage Charges etc., complete for finished items of work as per drawing and as per standered specification of respective item.

Supply and placing of the M-25 Grade (with cement 380 kg per cum) Design Mix Concrete corresponding to IS 456 using Batching Plant at 50 cum per hour,Transit mixer 2cum capacity and concrete Pump with 20mm size hard granite machine crushed well graded metal (coarse aggregate - as per IS 383 - 1970 and IS 2386 Part 1 to Part 8), from approved quarry, fine aggregate { 50% of River Sand (Natural Sand) & 50% of Manufactured Sand/Crushed stone sand/Rock sand 4.75mm to 2.36 mm confirming to IS 383 }, including cost and conveyance of all materials like cement, fine aggregate {River Sand (Natural Sand) & Manufactured Sand/Crushed stone sand/Rock sand } , coarse aggregate, water etc., to site, including all operational, incidental and all labour charges such as weigh batching, machine mixing, laying concrete, curing, etc., and overheads & contractors profit,all taxes except GST & Seigniorage chareges, including HIRE CHARGES FOR CENTERING & SCAFFOLDING but excluding cost of steel and its fabrication charges , complete for finished item of work.

Footings

Columns - upto plinth level

Grade & Plinth beam work

Columns work - above Plinth level

Tie Beams/Roof Beams

VRCC Slab work of 150mm thickness

Vaccum dewatering the concrete floors using TREMIX or equivalent over and finishing the top surface to required level/ slope and grade with rough / polish finish using power trowels (both fan & disc) of standard make including curing, mixing of hardening compound ,cutting of VDF floor 100 mm thick in M-25 grade of concrete with minimum cement content of 380 kgs using 20mm to down graded HBG metal and fine aggregate { 50% of River Sand (Natural Sand) & 50% of Manufactured sand/Crushed stone sand/Rock sand 4.75mm to 2.36 mm confirming to IS 383 } complete as per specification and drawing. 500 micron LDPe Sheet(Geo Membrane) , providing construction and expansion joins not more than 3.5mX3.5mts panels as directed by Engneer in Charge including providing necessary slopes for drain of water, in cluding cost and conveyance of all material to site, all incidental all operational charges, labour charges, contractor and over head charges, all taxes except GST & seigniorage charges etc., complete as directed by the Engineer-in-Charge for finished item of work. For VDF FLOORING of 100 mm thick .

Supplying fitting and placing Thermo Mechanically Treated (TMT) (Fe 500 grade as per IS 1786-1979) of all diametres using primary producers like TATA, SAIL, VSP, Jindal, Shyam Steel etc., of bar reinforcements for RCC works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes except GST on all materials etc. , but includingoverheads & contractors profit etc., complete for finished item of work for all floors .( APSS No.126)

RR masonry in CM(1:6) prop.using hard granite stone from approved quarry including cost and conveyance of all materials to site,fine aggregate (River sand),water etc. to site, all labour charges for dressing stones to required size and shape,mixing of cement mortor, stone wall construction,curing,etc., including overheads & contractors profit, all taxes except GST & seigniorage charges, complete as directed by the Engineer-in-Charge for finished item of work (APSS No. 615)

Masonry work in CM(1:6) prop (Cement : Screened sand) in superstructure with fly ash cement blocks of size 290mm x 225mm x 140mm for manufacturing fly ash solid blocks using fly ash of 80kgs, cement of 50 kgs, Gypsum of 5 kgs and stone dust from approved source having minimum crushing strength of 50 Kg/Sqcm. including cost and conveyance of all materials like cement, sand, fly ash bricks, water etc., to site, including sales & other taxes except GST & seigniorage chareges on all materials and labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, overheads and contrctor profit etc., complete for finished item of work. (APSS No. 501 & 504) -Ground Floor

Reinforced Masonry for partition walls (100 mm thick) in CM (1:4) prop. (Cement : Screened sand) using fly ash cement / lime solid blocks of size 225 x 100 x 60 mm having minimum compressive strength of 50 Kg/Sq.cmand placing 2 Nos. of 6mm M.S plain rods in every third layer with free ends of the reinforcement pegged into mortar joints of main brick walls where applicable including cost and conveyance of all materials like cement, steel, sand, bricks, water etc., to site, including sales & other taxes except GST & seigniorage chareges on all materials, all operational, incidental charges such as labour charges for mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, etc., and overheads & contractors profit but excluding cost of steel and its fabrication charges complete for finished item of work. (APSS No. of 509) - Ground Floor

Proviiding Dadooing to walls with glazed full body glazed red or white full body ceramic wall tiles of size 300 x 600 mm and thickness between 6-8mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs and make set over a base coat of C.M (1:3) proportion, 12mm thick and neat grey cement slurry of honey like consistency, spread at the rate of 3.3kgs per sqm and jointed with white cement or coloured cement to match the shade of the tiles, including cost and conveyance of all materials like cement, sand, water, tiles, coloured cement etc., to site, cost of base coat cement, all operational and incidental charges, labour and lift charges on all materials and all labour charges for mixing of cement mortar, laying glazed tiles to level, curing, overheads & contractors profit, all taxes, except GST & seigniorage charges etc., complete as directed by Engineer-in-charge . for finished item of work.

Flooring with non-skid full body ceramic floor tiles of size 300mm x 300mm and thickness between 7 - 8mm 1st quality conforming to IS: 13711, IS: 13712, IS: 13630(Part 1 to 15) of any colour and finish in all shades and designs as approved by Engineer-in-charge, set over base coat of cement mortar (1:8), 12mm thick using screened sand over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 Kgs per Sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, screened sand , water and tiles, and overheads & contractors profit all taxes except GST & seigniorage charges etc., complete for finished item of work.( In toilets) (APSS No.701 & 707)

Flooring with Nano polished /stain free soluble salt porcelain vitrified tiles screen printed of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designsas directed by the Engineer-In -Charge, laying tiles, set over a base coat of CM (1:8) prop. 20mm thick using screened sand over CC bed already laid or RCC roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per Sqm. and jointed neately with white cement paste mixed with pigment of matching shade to full depth including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site (excluding cost of C.C. bed) including cost of all materials,cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as, including all taxes except GST & seigniorage charges, complete as directed by the Engineer- in-charge. (APSS No.701 & 707)

Plastering 12mm thick in two coats using screened sand with base coat of 9mm thick in CM (1:6) and top coat of 3mm thick in CM (1:3) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site, including sales & other taxes except GST & seignorge charges on all materials, and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, scaffolding, lift charges, curing, including cutting grooves as directed by Engineer - in - charge etc., and overheads & contractors profit etc., complete for finished item of work. (SS 901,903 & 904)

Ornamental plastering to ceiling 12 mm thick in two coats with base coat of 8mm thick in CM (1:5) and top coat of 4mm thick in CM (1:3) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site, all taxes except GST & seigniorage charges and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, scaffolding, lift charges, curing, including cutting Grooves as directed by Engineer - in - charge etc., for finished item of work .(SS 901,903 & 904 for RCC exposed faces for finished item of work, for:-Ceiling Plastering 2/c in CM (1:3) & (1:5): 12 mm

Plastering 20mm thick in two coats using screened sand with base coat of 16mm thick in CM(1:6) and top coat of 4mm thick in CM(1:4) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site, including sales & other taxes except GST & seigniorge charges on all materials, and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, scaffolding, lift charges, curing, including cutting grooves as directed by Engineer-in-charge etc., and overheads & contractors profit complete for finished item of work .(SS 901,903 & 904) for:-Plastering 2/c in CM (1:4) & (1:6): 20 mm

Supply & application of one coat water based cement primer of interior grade I and two coats of acrylic emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/litre for internal walls including cost and conveyance of all materials to site, sales & other taxes, except GST incidental, operational and all labour charges etc., and overheads & contractors profit etc., complete for finished item of work in all floors.

Supply & application of one coat water based cement primer of exterior grade II and two coats of acrylic emulsion paint exterior grade with silicon additives having VOC (Volatile Organic Compound) content less than 50 grams/ liter for exterior walls including cost and conveyance of all materials to site, sales & other taxes except GST, incidental, operational and all labour charges etc., and overheads & contractors profit, complete for finished item of work in all floors. External Painting .

Painting to Ceiling with two coats of white cement paint of apporved brand over a base coat of approved cement primer Grade-I making 3 coats in all to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges all taxes except GSTetc. complete for finished item of work.

Painting two coats with synthetic enamel paint Grade-I VOC (Volatile Organic Compound) content less than 50 grams/litre over primer coat of red oxide to new iron work including cost and conveyance of all materials to site, sales & other taxes except GST, incidental, operational and all labour charges etc., and overheads & contractors profit etc., complete for finished item of work in all floors. (SS No. 1201, 1212 & 1207).

Supply, manufacture, making to specified design including Labour charges for fabricating steel works like Window Grills, Compound Wall Grills, Iron Doors, Windows including cost of welding rods, power charges, including cost of fixing in position, all incidental, operational, labour charges all taxes except GST etc., complete for finished item of work

Supplying and fixing of stainless steel ( grade 304 ) hand railing of height as per approved drawing with top rail of 50mm dia pipe and 2mm thick medium class and vertical posts of 25mm dia and 1.6mm thick medium class 2 Nos for each step fixed with base plate of 75mm dia using bonding agent and anchor fastner and welding, drilling of 20mm dia holes with pneumatic compressor for fixing railing, buffing, polishing all members of the railing thouroughly , lacquer finishing to present seamless finish including cost and conveyance of all materials, electrodes, welding charges, cost of all consumables, labour charges , overheads & contractors profit, all taxes except GST etc., complete for finished item of work.

Supplying and fixing of Unplasticised Poly Vinyl Chloride (UPVC) casement windows openable shutters duly manufactured using UPVC reinforced profiles (Composition of profile shall consists a minimum of 5.5 PHR of TiO2 and not more than 12 PHR of CaCo3 for every 100 parts of PVC resin) of 60 mm x 55 mm x 2.40 mm for outer frames, 74 mm x 60 mm x 2.40 mm for mullion sections for two or more openable shutters 75 mm x 60 mm x 2.40 mm for openable shutter frame capable of mounting single glazing system structurally reinforced with hot dip galvanized up to 50 microns of minimum thickness of 1.0/1.2 mm prefabricated & welded through fusion welding.The window sash shall be fitted with 5 mm thick clear float glass of reputed make duly fixed with Grey colour TPV Gasket for sash & Glazing bead shall be co-extruded with Grey colour soft PVC and accessories for casement window – friction hinges of stainless steel grade 304/430- 2 Nos., per sash, handle with zamak alloy casting 1 No. per sash, multipoint locking system suitably concealed 1 No., per sash provided with raiser wedges for smooth operation and the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing/ deglazing at site etc., including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site , overhead charges & contractor profit all taxes, excliding GST, for finished item of work.

Providing, supplying & fixing of Fixed Louvered Ventilator made out of multi chambered uPVC sections with Glazing bead shall be co-extruded with Grey colour soft PVC. having isolated drainage and reinforced with Galvanized Iron profiles throughout the window. The outer frame having an overall size of 60 mm x 55 mm x 2.40mm with reinforcement of 1 mm thickness and Mullion with overall size of 74 mm x 60 mm x 2.40 mm with reinforcement of 1 mm thickness. (Composition of profile shall consists a minimum of 5.5 PHR of TiO2 and not more than 12 PHR of CaCo3 for every 100 parts of PVC resin).Ventilator shall be provided with 4.5 mm Pin Head glass, standard hardware. Wall thickness of frame & Mullion shall be 2.4 mm.,including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site, overhead charges & contractor profit, all taxes except GST , complete for finished item of work.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 95 mm x 60 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness .The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame, including cost and conveyane of all materials to site , all labour charges for fixing in position, all over head charges and contractor profit all taxes, except GST etc., complete . .

30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/ Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856 with Fixtures of powder coated MS Butt Hinges 100mmx58mmx1.9mm, Bright finished or black enamiled mild screw 40mm & 20mm , including cost of PU Paint and SS 304 Hardware ,including cost and conveyane of all materials to site , all labour charges for fixing in position, all over head charges and contractor profit all taxes, except GST etc., complete

Supply & Fixing of Single door with medium teak wood frame of size 100X65 mm and Flush shutter of solid bond wood block board type 35 mm thick with teak ply on both faces. conforming to IS:2202, fixing door frame to the wall with Fixtures of of 3 Nos of 125 mm long Brass Butt Hinges,1 Nos of 250 mm Long Brass Tower Bolt,2 Nos of 200 mm Long Brass Handle,1 No of Heavy Duty Mortice Locks,1 No of Aluminium Extruded Door Closure ,Rubber Beading Buffer and MS z hold Fasts as per approved drawing including Labour charges for wrought and put up and fixing in position, overheads and contractor's profit , all taxes, except GSTetc.,complete for finihsed item of work.

Extra for providing lipping with best teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).Extra for providing lipping with 2nd class teak wood battens 25 mm minimum, including all over head charges and contractor profit all taxes, except GST etc., complete as directed by Engineer-in-charge for finished item of work.

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings, including all over head charges and contractor profit all taxes, except GST etc., complete as per direction of Engineer-in-charge for finished item of work.

Providing and laying precast concrete blocks for paving of M-40 grade and thickness not less than 80 mm for Medium traffic areas conforming to IS 15658:2006 laid in required colour and pattern laid over 50 mm thick compacted bed of sand(River sand) and gaps filled with fine sand (River Sand) inclusive of all taxes except GST & seigniorage Charges etc., including all operational, incidental and labour charges, over head charges and contractor profit, complete as directed by the Engineer -in -charge for finished item of work.

Providing Granular Sub Base using HBG crushed close graded material confirming to grading -II of MoRTH table - 400.1 (35% of 26.5mm to 9.5mm , 25% of 9.5 to 2.36mm and 40% of 2.36mmm below)including spreading the HBG material in layers of uniform thickness not exceeding 150mm thick with motor grader on prepared surface, mixing by mix in place method at OMC and compacting with vibratory roller to achieve the desired density complete as per technical specification as directed by the Engineer-in-charge etc, including cost and conveyance of HBG material, water etc to site, seigniorage charges, labour charges for all operations, all incidentals hire & operational charges of roller and other T&P etc,excluding GST complete for finished item of work as per MoRT&H (5th Revision) Specification 401.

Design, supply and construction of PEB Cold Storage building by using the built up sections are made from hot rolled platers conforming to ASTM A - 572 GR 50 and other sections except beams are mill sections complying with IS : 2062 and the section should be provided with 2 coats of Zinc Phosphate Anti Corrosion Paint after sand blasting and 2 coats of enamel paints as per the approved colour. Bracing rods and sag rods are made of steel bars conforming to IS 2062 with a minimum yield strength of 240 MPa. All the fasteners should be confimed as per the IS/ASTM specifications. The roofing and Fascia board should be ZINC Aluminium alloy coated colour roof sheet of 0.47mm nominal thickness, cold roll formed from a cold rolled coil confirming to ASTM A 792 M Grade 80 with a minimum uield strenght of 550 MPa. The eves gutter should be provided with Zinc Aluminium alloy coated steel sheet of 0.8T with GI Gutter hangers. Downspouts are should be provided with 100mm size of Zinc aluminium coated shees with GI Leader straps. Galvanised purlin should be addopted as pe the required size. The quotated price should include the supply and fixing charges of MS inserts in the concrete, day light sheets in the Roof, Turbo ventilators, wall side cladding from finished floor level to roof sheet level with necessary supporting purlins & clamps, flashings etc. complete. Also the quoted rate should include all necessary labour charges and material and machinery charges including all works related the PEB structures excluding Civil works as per the detailed drawing and instructions of engineer in charge. Payment will be made as per the approved drawings on plinth area basis. The area under canopy, toilets and record room are factored in the unit cost and shall not be measured.

Design, supply and construction of PEB Ware House building by using the built up sections are made from hot rolled platers conforming to ASTM A - 572 GR 50 and other sections except beams are mill sections complying with IS : 2062 and the section should be provided with 2 coats of Zinc Phosphate Anti Corrosion Paint after sand blasting and 2 coats of enamel paints as per the approved colour. Bracing rods and sag rods are made of steel bars conforming to IS 2062 with a minimum yield strength of 240 MPa. All the fasteners should be confimed as per the IS/ASTM specifications. The roofing and Fascia board should be ZINC Aluminium alloy coated colour roof sheet of 0.47mm nominal thickness, cold roll formed from a cold rolled coil confirming to ASTM A 792 M Grade 80 with a minimum uield strenght of 550 MPa. The eves gutter should be provided with Zinc Aluminium alloy coated steel sheet of 0.8T with GI Gutter hangers. Downspouts are should be provided with 100mm size of Zinc aluminium coated shees with GI Leader straps. Galvanised purlin should be addopted as pe the required size. The quotated price should include the supply and fixing charges of MS inserts in the concrete, day light sheets in the Roof, Turbo ventilators, wall side cladding from finished floor level to roof sheet level with necessary supporting purlins & clamps, flashings etc. complete. Also the quoted rate should include all necessary labour charges and material and machinery charges including all works related the PEB structures excluding Civil works as per the detailed drawing and instructions of engineer in charge. Payment will be made as per the approved drawings on plinth area basis. The area under canopy, toilets and record room are factored in the unit cost and shall not be measured.

No. of Items : 36( Thirty Six only)

(Rupees Two Crores Fifty Lakhs Seventy Nine Thousand Three Hundred and Eleven Only)

Part-I

Part-II - Seigniorage Charges payable as per actuals

Note : 1)The Rates given in schedule 'A' under Part-I are excluding GST.The Tender Percentage(Excess or Less ) shall not apply to the above items under Part-II

1) The rates mentioned in schedule 'A' are including all taxes except GST. 2) The above rates are for finished items of work including cost and convenyance of all requisite materials to site, Seigniorage Charges, Labour Charges for all operationas, curing wherever needed, all Incidental, Hire and Operational charges of all T&P barricading, Diversion of traffic etc.