Water Resources Department Tender

Fabricating, supplying and erection of Screw Gearing steel shutters of size 0.23 m x 0.60 m with consists of skin plate made out of 8 mm thick mild steel plate and horizontally stiffened with 100 mm x 50 mm x 6 mm steel channel (ISMC) at an interval of not more than 0.5 m and vertical stiffeners made out of same section at an interval not more than 0.6 m and provided with 8 mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Groove Channels of ISMC 100mmx100mmx10mm mild steel angle for required height up to 1.50 m including welding hold fast of size 40 mm x 40 mmx 6 mm mild steel angle 3 numbers on both sides. Providing Sill Beam of 150mm x 80mm x 6mm, 0.23 m length and providing of 63 mm screw rod made of mild steel duly machined and fully threated to suite the Head set assembly with required height up to 2.0m and required holes. Fixing the screw rod to the shutter gusset plate with required bolts and nuts in proper alignment to the Head Set. Providing of Top Beam made up of 200 mm x 100 mm x 6 mm (ISMB 200) for the length of 0.83 m duly drilled to suite the Head Set assembly with required bed bolts made out of 25 mm mild steel round rod duly threated with suitable anchorage arrangements to the height of 0.6 m with necessary fish plate made out of 16 mm mild steel plate of size 0.2 m x 0.3 m 2 numbers with require bolts. Providing Head set assembly medium duty with Hexagonal nut (approximate 70 kg) made up of cast iron

Fabricating, supplying and erection of Screw Gearing steel shutters of size 1.80 m x 1.50 m with consists of skin plate made out of 8 mm thick mild steel plate and horizontally stiffened with 100 mm x 50 mm x 6 mm steel channel (ISMC) at an interval of not more than 0.5 m and vertical stiffeners made out of same section at an interval not more than 0.6 m and provided with 8 mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Groove Channels of ISMC 100mmx100mmx10mm mild steel angle for required height up to 3.50 m including welding hold fast of size 40 mm x 40 mmx 6 mm mild steel angle 3 numbers on both sides. Providing Sill Beam of 150mm x 80mm x 6mm, 1.80m length and providing of 63 mm screw rod made of mild steel duly machined and fully threated to suite the Head set assembly with required height up to 3.00 m and required holes. Fixing the screw rod to the shutter gusset plate with required bolts and nuts in proper alignment to the Head Set. Providing of Top Beam made up of 200 mm x 100 mm x 6 mm (ISMB 200) for the length of 2.40 m duly drilled to suite the Head Set assembly with required bed bolts made out of 25 mm mild steel round rod duly threated with suitable anchorage arrangements to the height of 0.6 m with necessary fish plate made out of 16 mm mild steel plate of size 0.2 m x 0.3 m 2 numbers with require bolts. Providing Head set assembly medium duty with Hexagonal nut (approximate 70 kg) made up of cast iron

Fabricating, supplying and erection of Screw Gearing steel shutters of size 1.73 m x 1.20 m with consists of skin plate made out of 8 mm thick mild steel plate and horizontally stiffened with 100 mm x 50 mm x 6 mm steel channel (ISMC) at an interval of not more than 0.5 m and vertical stiffeners made out of same section at an interval not more than 0.6 m and provided with 8 mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Groove Channels of ISMC 100mmx100mmx10mm mild steel angle for required height up to3.0 m including welding hold fast of size 40 mm x 40 mmx 6 mm mild steel angle 3 numbers on both sides. Providing Sill Beam of 150mm x 80mm x 6mm, 1.73m length and providing of 63 mm screw rod made of mild steel duly machined and fully threated to suite the Head set assembly with required height up to 3.00 m and required holes. Fixing the screw rod to the shutter gusset plate with required bolts and nuts in proper alignment to the Head Set. Providing of Top Beam made up of 200 mm x 100 mm x 6 mm (ISMB 200) for the length of 2.33 m duly drilled to suite the Head Set assembly with required bed bolts made out of 25 mm mild steel round rod duly threated with suitable anchorage arrangements to the height of 0.6 m with necessary fish plate made out of 16 mm mild steel plate of size 0.2 m x 0.3 m 2 numbers with require bolts. Providing Head set assembly medium duty with Hexagonal nut (approximate 70 kg) made up of cast iron

Providing and placing in position of Plain Cement Concrete of grade M 10 using hard well graded coarse aggregate of maximum nominal size of 40mm and downgraded to I.S specified grading (to produce concrete of the specified characteristic strength of 10N/Sqmm in 28 days) including dewatering the placement site by bailing / pumping and diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, compacting and finishing the surface to the profile with all leads and lifts, watering, curing to attain the strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with standard specification and as directed by the Engineer in charge of work.

Providing and placing in position of Plain Cement Concrete of grade M15 using hard well graded coarse aggregate of maximum nominal size of 40mm (60%) and 20mm (40%) and downgraded to I.S specified grading (to produce concrete of the specified characteristic strength of 15 N/Sqmm in 28 days) including dewatering the placement site by bailing / pumping and diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, vibrating, compacting and finishing the surface to the profile with all leads and lifts, watering, curing to attain the strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with standard specification and as directed by the Engineer in charge of work.

including moulding, machining and Hexagonal nut threaded to suit screw rod provided with thrust bearings for smooth operation. The whole shutter assembly should be painted with two coats of anti-corrosive black paint over one coat of red oxide primer paint. Erecting Shutter including crane hire charges (As per SR p .257) The rate is inclusive of all materials, labour charges including Lathing, Drilling, Welding, Gas cutting, Hydraulic bend removing of M.S. rod, hire charges of Crane and also inclusive of cost of covering plate, Foundation bolts, all bolt and nuts, conveyance to this site, Loading and unloading charges, Grease packing, Lubricating oil, Operating key, Locking arrangement and checking the Shutter operation etc., complete as directed by the Departmental Officers. Shutter size 1.73 m x 1.20 m

With strutting

Fabricating, supplying and erection of Screw Gearing steel shutters of size 0.30 m x 0.60 m with consists of skin plate made out of 8 mm thick mild steel plate and horizontally stiffened with 100 mm x 50 mm x 6 mm steel channel (ISMC) at an interval of not more than 0.5 m and vertical stiffeners made out of same section at an interval not more than 0.6 m and provided with 8 mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Groove Channels of ISMC 100mmx100mmx10mm mild steel angle for required height up to 1.50 m including welding hold fast of size 40 mm x 40 mmx 6 mm mild steel angle 3 numbers on both sides. Providing Sill Beam of 150mm x 80mm x 6mm, 0.3 m length and providing of 63 mm screw rod made of mild steel duly machined and fully threated to suite the Head set assembly with required height up to 2.0m and required holes. Fixing the screw rod to the shutter gusset plate with required bolts and nuts in proper alignment to the Head Set. Providing of Top Beam made up of 200 mm x 100 mm x 6 mm (ISMB 200) for the length of 0.9 m duly drilled to suite the Head Set assembly with required bed bolts made out of 25 mm mild steel round rod duly threated with suitable anchorage arrangements to the height of 0.6 m with necessary fish plate made out of 16 mm mild steel plate of size 0.2 m x 0.3 m 2 numbers with require bolts.

Earth work excavating and dopositting on bank with intial lead of 10 m & intial lift of 2m in hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders etc., complete complying with standard specification and as directed the Engineer in charge of work.

Fabricating, supplying and erection of Screw Gearing steel shutters of size 0.45 m x 0.60 m with consists of skin plate made out of 8 mm thick mild steel plate and horizontally stiffened with 100 mm x 50 mm x 6 mm steel channel (ISMC) at an interval of not more than 0.5 m and vertical stiffeners made out of same section at an interval not more than 0.6 m and provided with 8 mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Groove Channels of ISMC 100mmx100mmx10mm mild steel angle for required height up to 1.50 m including welding hold fast of size 40 mm x 40 mmx 6 mm mild steel angle 3 numbers on both sides. Providing Sill Beam of 150mm x 80mm x 6mm, 0.4 m length and providing of 63 mm screw rod made of mild steel duly machined and fully threated to suite the Head set assembly with required height up to 2.0m and required holes. Fixing the screw rod to the shutter gusset plate with required bolts and nuts in proper alignment to the Head Set. Providing of Top Beam made up of 200 mm x 100 mm x 6 mm (ISMB 200) for the length of 1.00 m duly drilled to suite the Head Set assembly with required bed bolts made out of 25 mm mild steel round rod duly threated with suitable anchorage arrangements to the height of 0.6 m with necessary fish plate made out of 16 mm mild steel plate of size 0.2 m x 0.3 m 2 numbers with require bolts. Providing Head set assembly medium duty with Hexagonal nut (approximate 70 kg) made up of cast iron

including moulding, machining and Hexagonal nut threaded to suit screw rod provided with thrust bearings for smooth operation. The whole shutter assembly should be painted with two coats of anti-corrosive black paint over one coat of red oxide primer paint.Erecting Shutter assembly by Durky post and Chain block. The rate is inclusive of all materials, labour charges including Lathing, Drilling, Welding, Gas cutting, Hydraulic bend removing of M.S. rod, hire charges of Crane and also inclusive of cost of covering plate, Foundation bolts, all bolt and nuts, conveyance to this site, Loading and unloading charges, Grease packing, Lubricating oil, Operating key, Locking arrangement and checking the Shutter operation etc., complete as directed by the Departmental Officers. Shutter size 0.23 m x 0.60 m

Providing and placing in position of Plain Cement Concrete of grade M15 using hard well graded coarse aggregate of maximum nominal size of 40mm weigh batching the ingeridents and mixing in approved mixers/ batching plant (to produce concrete of the specified characteristic strength of 15N/Sqmm in 28 days) including dewatering the placement site by bailing / pumping and diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, compacting and finishing the surface to the profile with all leads and lifts, watering, curing to attain the strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with standard specification and as directed by the Engineer in charge of work.

Supplying and erecting water tight steel centering for sides and soffits including supports and strutting up to height of 3.29 m high for plain surface such as R.C.C.slabs, vertical slabs,side slabs of R.C.C. Works with all cross bracings using mild steel B.G.10 gauge sheets of size 90cm x 60cm stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding laid over silver oak (country wood) joists of size 10cm x6.5cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre to centre complete complying with standard specification and as directed by the by the Engineer in charge of work (The retrieved materials should be taken back by the contractor ). The payment for centering should be made after the concrete is laid etc.,

GST 18%

Concrete upto 1 m height above GL and upto 1.50m depth below ground level

including moulding, machining and Hexagonal nut threaded to suit screw rod provided with thrust bearings for smooth operation. The whole shutter assembly should be painted with two coats of anti-corrosive black paint over one coat of red oxide primer paint. Erecting Shutter including crane hire charges (As per SR p .257) The rate is inclusive of all materials, labour charges including Lathing, Drilling, Welding, Gas cutting, Hydraulic bend removing of M.S. rod, hire charges of Crane and also inclusive of cost of covering plate, Foundation bolts, all bolt and nuts, conveyance to this site, Loading and unloading charges, Grease packing, Lubricating oil, Operating key, Locking arrangement and checking the Shutter operation etc., complete as directed by the Departmental Officers. Shutter size 1.80 m x 1.20 m

Earth work deploying earth moving machineries for desilting channel and forming bund on either side and depositing the earth on banks including jungle clerence etc complete complying with standard specification and as directed by the the Engineer in charge of work. Having a width of 3m - 10m

Providing Head set assembly medium duty with Hexagonal nut (approximate 70 kg) made up of cast iron including moulding, machining and Hexagonal nut threaded to suit screw rod provided with thrust bearings for smooth operation. The whole shutter assembly should be painted with two coats of anti-corrosive black paint over one coat of red oxide primer paint.Erecting Shutter assembly by Durky post and Chain block. The rate is inclusive of all materials, labour charges including Lathing, Drilling, Welding, Gas cutting, Hydraulic bend removing of M.S. rod, hire charges of Crane and also inclusive of cost of covering plate, Foundation bolts, all bolt and nuts, conveyance to this site, Loading and unloading charges, Grease packing, Lubricating oil, Operating key, Locking arrangement and checking the Shutter operation etc., complete as directed by the Departmental Officers. Shutter size 0.30 m x 0.60 m

2 numbers with require bolts. Providing Head set assembly medium duty with Hexagonal nut (approximate 70 kg) made up of cast iron including moulding, machining and Hexagonal nut threaded to suit screw rod provided with thrust bearings for smooth operation. The whole shutter assembly should be painted with two coats of anti-corrosive black paint over one coat of red oxide primer paint.Erecting Shutter assembly by Durky post and Chain block. The rate is inclusive of all materials, labour charges including Lathing, Drilling, Welding, Gas cutting, Hydraulic bend removing of M.S. rod, hire charges of Crane and also inclusive of cost of covering plate, Foundation bolts, all bolt and nuts, conveyance to this site, Loading and unloading charges, Grease packing, Lubricating oil, Operating key, Locking arrangement and checking the Shutter operation etc., complete as directed by the Departmental Officers. Shutter size 0.60 m x 0.60 m

Dismantling clearing away and carefully stacking materials useful for re-use for any thickness of plain cement concrete etc, complete complying with standard specification and as directed by the Engineer in charge of work.

Forming ring bund using with 80 bags per 100cft filled with using crushed stone sand stitching the bags with jute coir, conveyed the stitched bags to river portion for forming ring bund by placing the stitched sand bags in proper position and packing tightly and plugging the joints with clay and straw leaves to arrest the leakages as directed by the departmental officers including the cost of empty bags, sand, jute coir etc., complete complying with standard specification and as directed by the departmental officers.

Without strutting

Fabricating, supplying and erection of Screw Gearing steel shutters of size 1.80 m x 1.20 m with consists of skin plate made out of 8 mm thick mild steel plate and horizontally stiffened with 100 mm x 50 mm x 6 mm steel channel (ISMC) at an interval of not more than 0.5 m and vertical stiffeners made out of same section at an interval not more than 0.6 m and provided with 8 mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Groove Channels of ISMC 100mmx100mmx10mm mild steel angle for required height up to3.0 m including welding hold fast of size 40 mm x 40 mmx 6 mm mild steel angle 3 numbers on both sides. Providing Sill Beam of 150mm x 80mm x 6mm, 1.80m length and providing of 63 mm screw rod made of mild steel duly machined and fully threated to suite the Head set assembly with required height up to 3.00 m and required holes. Fixing the screw rod to the shutter gusset plate with required bolts and nuts in proper alignment to the Head Set. Providing of Top Beam made up of 200 mm x 100 mm x 6 mm (ISMB 200) for the length of 2.40 m duly drilled to suite the Head Set assembly with required bed bolts made out of 25 mm mild steel round rod duly threated with suitable anchorage arrangements to the height of 0.6 m with necessary fish plate made out of 16 mm mild steel plate of size 0.2 m x 0.3 m 2 numbers with require bolts. Providing Head set assembly medium duty with Hexagonal nut (approximate 70 kg) made up of cast iron

Providing and placing in position of Plain Cement Concrete of grade M15 using hard well graded coarse aggregate of maximum nominal size of 20mm and downgraded to I.S specified grading (to produce concrete of the specified characteristic strength of 15N/Sqmm in 28 days) including dewatering the placement site by bailing / pumping and diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, compacting and finishing the surface to the profile with all leads and lifts, watering, curing to attain the strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with standard specification and as directed by the Engineer in charge of work.

Supplying and Fixing demarcation R.C.C. pre cast posts in Cement concrete of grade M20 with well graded aggregates and the nominal maximum size of coarse aggregate of size 20 mm of size 0.15 x 0.15 x 1.20 M and fixing the post 40 Cm depth below ground level, the post includes using 4 numbers of 8mm RTS main rod to a length of 1.325 M, using 6mm MS 9 numbers as strips with steel centering and painting the post with enamel paint to a height of 0.80 M around the post etc. complete and conveying the post to the site of demarcation boundary such as tank bund and foreshore including earth work excavation for foundation in HSC having the base plain cement concrete of 10 cm of grade M15 concrete using hard blue granite broken stone of graded metal 1/3 Part of 40mm & 2/3 Part of 20 mm size, and the post embedded by using Cement concrete of grade M10 with well graded aggregates and the nominal maximum size of coarse aggregate of 20 mm etc, complete as directed by the Engineer in charge of works and as per the technical specifications

Concrete above 1 m height and upto 4.50m height above ground level

including moulding, machining and Hexagonal nut threaded to suit screw rod provided with thrust bearings for smooth operation. The whole shutter assembly should be painted with two coats of anti-corrosive black paint over one coat of red oxide primer paint. Erecting Shutter including crane hire charges (As per SR p .257) The rate is inclusive of all materials, labour charges including Lathing, Drilling, Welding, Gas cutting, Hydraulic bend removing of M.S. rod, hire charges of Crane and also inclusive of cost of covering plate, Foundation bolts, all bolt and nuts, conveyance to this site, Loading and unloading charges, Grease packing, Lubricating oil, Operating key, Locking arrangement and checking the Shutter operation etc., complete as directed by the Departmental Officers. Shutter size 1.80 m x 1.50 m

Concrete depth 1.5 m and upto 4.50m depth below ground level

Dewatering using 20HP diesel engine pumpset including Hire charges, cost of Diesel, Engine oil, pump operator, labour charges, conveyance of pumpset and fuel to site and back, loading, unloading and any other incidental charges etc., complete complying with standard specification and as directed by the departmental officers.

Fabricating, supplying and erection of Screw Gearing steel shutters of size 0.60 m x 0.60 m with consists of skin plate made out of 8 mm thick mild steel plate and horizontally stiffened with 100 mm x 50 mm x 6 mm steel channel (ISMC) at an interval of not more than 0.5 m and vertical stiffeners made out of same section at an interval not more than 0.6 m and provided with 8 mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Groove Channels of ISMC 100mmx100mmx10mm mild steel angle for required height up to 1.50 m including welding hold fast of size 40 mm x 40 mmx 6 mm mild steel angle 3 numbers on both sides. Providing Sill Beam of 150mm x 80mm x 6mm, 0.6 m length and providing of 63 mm screw rod made of mild steel duly machined and fully threated to suite the Head set assembly with required height up to 2.0m and required holes. Fixing the screw rod to the shutter gusset plate with required bolts and nuts in proper alignment to the Head Set. Providing of Top Beam made up of 200 mm x 100 mm x 6 mm (ISMB 200) for the length of 1.20 m duly drilled to suite the Head Set assembly with required bed bolts made out of 25 mm mild steel round rod duly threated with suitable anchorage arrangements to the height of 0.6 m with necessary fish plate made out of 16 mm mild steel plate of size 0.2 m x 0.3 m

Providing and placing in position of Plain Cement Concrete of grade M20 using hard well graded coarse aggregate of maximum nominal size of 20mm and downgraded to I.S specified grading (to produce concrete of the specified characteristic strength of 20N/Sqmm in 28 days) including dewatering the placement site by bailing / pumping and diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, compacting and finishing the surface to the profile with all leads and lifts, watering, curing to attain the strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with standard specification and as directed by the Engineer in charge of work. Concrete upto 1 m height above GL and upto 1.50m height below ground level

Providing and fixing weep holes of 110mm dia PVC pipe of working pressure 4Kg/cm2 to a required length for protection wall , Abutment & Wing wall etc., Including cost of all materials to work site including labour charges for 90cm spherical backfill arrangement with 110 mm dia and 20mm size hard granite broken stone charges at the periphery, the labour charges for fixing to drain the back fill etc., Complete complying with standard specification and as directed by the by the Engineer in charge of work.

Clearing the juliflora jungle without uprooting etc, complete complying with standard specification and as directed by the Engineer in charge of work.

Supplying, fabricating and placing in position of RTS or MS reinforcement for all reinforced cement concrete works including cost of steel rods of all sizes including binding wires and labour charges for decoiling, cutting, bending and tying the grills in position etc., complete complying with standard specification and as directed by the departmental officers.

Earthwork in all soils except hard rock requiring blasting and conveying for formation of bund and transporting the same with a lead of 6KM MR deploying earth moving machineries and Tippers including benching, formation of bund in layers of suitable thickness, depending upon type of compaction equipment deployed and not exceeded 23cm thickness, breaking clods, watering to Opitimum moisture content (OMC) and compaction of each layers to 95 % of procter density through deployment of appropriyate compaction equipment (8-10 T) power roller / vibratory power roller/ short width (+0.90m width drum) power roller or vibratory power roller ensuring compaction of designed bund section also ensuring compaction of earth fill and side slopes through deployment of hydraulic excavators with steel plate fixures attached to their booms/ heavy power roller capable of claimbing 2.00(Horizandal):1.00(Vertival) slope including side slope complete complying with standard specification and as directed by the the Engineer in charge of work.

Fabricating, supplying and erection of Screw Gearing steel shutters of size 1.90 m x 1.50 m with consists of skin plate made out of 8 mm thick mild steel plate and horizontally stiffened with 100 mm x 50 mm x 6 mm steel channel (ISMC) at an interval of not more than 0.5 m and vertical stiffeners made out of same section at an interval not more than 0.6 m and provided with 8 mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Groove Channels of ISMC 100mmx100mmx10mm mild steel angle for required height up to 3.50 m including welding hold fast of size 40 mm x 40 mmx 6 mm mild steel angle 3 numbers on both sides. Providing Sill Beam of 150mm x 80mm x 6mm, 1.90m length and providing of 63 mm screw rod made of mild steel duly machined and fully threated to suite the Head set assembly with required height up to 3.00 m and required holes. Fixing the screw rod to the shutter gusset plate with required bolts and nuts in proper alignment to the Head Set. Providing of Top Beam made up of 200 mm x 100 mm x 6 mm (ISMB 200) for the length of 2.50 m duly drilled to suite the Head Set assembly with required bed bolts made out of 25 mm mild steel round rod duly threated with suitable anchorage arrangements to the height of 0.6 m with necessary fish plate made out of 16 mm mild steel plate of size 0.2 m x 0.3 m 2 numbers with require bolts. Providing Head set assembly medium duty with Hexagonal nut (approximate 70 kg) made up of cast iron

including moulding, machining and Hexagonal nut threaded to suit screw rod provided with thrust bearings for smooth operation. The whole shutter assembly should be painted with two coats of anti-corrosive black paint over one coat of red oxide primer paint. Erecting Shutter including crane hire charges (As per SR p .257) The rate is inclusive of all materials, labour charges including Lathing, Drilling, Welding, Gas cutting, Hydraulic bend removing of M.S. rod, hire charges of Crane and also inclusive of cost of covering plate, Foundation bolts, all bolt and nuts, conveyance to this site, Loading and unloading charges, Grease packing, Lubricating oil, Operating key, Locking arrangement and checking the Shutter operation etc., complete as directed by the Departmental Officers. Shutter size 1.90 m x 1.50 m

Dismantling clearing away and carefully stacking materials useful for re-use for any thickness of walls Brick / Stone Masonry in cement mortar walls under 3m high etc, complete complying with standard specification and as directed by the Engineer in charge of work.