Tamil Nadu Veterinary And Animal Sciences University Tender

Supplying and filling in foundation, basement, etc with filling M.sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with Quarry Dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Refilling in foundation, basement, etc with excavaed earth in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five M.sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and erecting steel shuttering including necessary supports for plain surfaces for reinforced cement concrete works such as grade beams, column footing, plinth beam, stair case steps, pedestals bed blocks cover slab etc., using mild steel B.G. 10 sheets of size 90cm X 60cm stiffened with mild steel angles of size 25mm X 25mm X 3mm for boarding laid over silver oak (Country wood) joists of size 10cm X 6.5 cm spaced at about 90cm centre to centre, supported by casurina props of 10cm to 13cm diameter spaced at 75cm centre to centre etc., complete complying with standard specification.

Supplying and erecting steel centering for sides and soffits including supports and strutting up to 3.29 meter height for plain surfaces such as RCC square or rectangular columns, top and bottom slabs of sunshade boxing sill slabs etc., with necessary facia etc., with all cross bracings using mild steel B.G., 10 sheets of size 90cm X 60cm stiffened with welded mild steel angles of size 25mm X 25mm X 3mm for boarding laid over silver oak (Country wood) Joists of size 10cm X 6.5 cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre to centre etc., complete complying with standard specification.

Supplying and erecting steel centering for sides and soffits including supports and strutting up to a height of 3.29m meter for plain surfaces such as RCC slabs, beams TEE or ELL beams, lintels staircases beams etc., with all cross bracings using mild steel B.G. 10 sheets of size 90cm X 60cm stiffened with welded mild steel angles of size 25mm X 25mm X 3mm laid over silver oak (Country wood) joists of size 10cm X 6.5cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at 75cm centre to centre etc., complete complying with standard specification in all floors.

Reinforced Cement Concrete 1:11/2:3 (One Cement, one and half M.sand and three hard broken stone jelly) using machine broken 20 mm gauge hard broken granite stone jelly for all RCC item of works excluding cost of reinforcement grill, fabricating charges, centering and shuttering but including laying, vibrating with mechanical vibrator, finishing, curing, etc., complete and providing fixtures like fan clamps in the RCC floor/roof slab wherever necessary and bearing surfaces of wall, beam etc. shall be finished smooth with cement mortar 1:3 (One Cement and Three P.Sand) 12mm thick and kraft paper laid over it without claiming extra, etc., complete complying with standard specification as directed by the departmental officers. For foundation and basement

For superstructure in Ground floor

Cement Concrete 1:4:8 (One Cement, four M.Sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Supplying, fabricating and placing in position of steel reinforcements using MS / RTS rods for all RCC works as per design given including cost of steel. Binding wire, straightening the rods, welding of rods, dia above 25mm in all floors complying with standard specifications. [The welding should conform to BIS. Wherever required at contractor’s expense.]

Brick work in Cement Mortar 1:5 (One cement and Five M.sand) using second class chamber burnt stock bricks of size 9”x 4½”x 3” for the following including curing, etc., complete complying with standard specification. For foundation and basement

For super structure in Ground floor

For super structure in First floor

Providing brick partition wall of 11.50 cm thick using best quality second class chamber burnt stock bricks of size 9” X 4 ½” X 3” in cement mortar 1:3 (One cement and three M.sand) including supply and fixing hoop iron reinforcement if considered necessary by the departmental officers as directed etc., complete complying with standard specifications. (The hoop reinforcement will be measured and paid separately). For Ground Floor

Special ceiling plastering and finishing the RCC exposed surface such as RCC slabs sunshade facia, canopy slab, stair case, waist slab, landing slab etc., with cement mortar 1:3 (One cement and three P.sand) 10mm thick including hacking and providing necessary cement mortar nosing, beading etc., wherever necessary and as directed with cement mortar etc., complete complying with standard specification

Plastering of walls in cement mortar 1:5 (One cement and five P.sand) 12mm thick in all floors including provision of cement mortar bands and raised plastering for doorways wherever required and as directed without any extra claim complying with standard specification.

Providing and fixing doors with door frames as per the design and details with the door farme made of well seasoned good quality teak wood frame size of 125mmX100mm finished with melamine polish of approved make, colour & pattern as per drawing and the door made of 35mm thick Teak flush door shutters of solid core block board type bonded with phenol formaldehyde synthetic resin thermo pressed with 8mm thick teak wood external edge lipping finished with melamine polish of approved make, colour & pattern as per drawing. The construction procedure of the shutter should be as per IS:2202.The size of block, shall perfectly correspond to the maximum size of lock, covered in IS:2209. All the four edges of the door shutter shall be square. The shutter shall be free from twist or warp in its plane and of required size etc. The rate shall inclusive of supplying and fixing 6 nos of MS holdfasts of size 230x50x6mm MS flats suitably folded to the rejoined ‘Z’ shape to have two end flats 50mm long and over all length of the horizontal position as 230mm and including making necessary groove in the two end flats to accommodate screws, and the following of hinges and other hardwares; complete as directed by the Engineer in charge.but the finishing of door shutters on both sides with 3.5mm thick veneer of approved color and finishing with melamine polish. The basic cost of veneer. The rate should be quoted for single side area of the door shutter. For Double Leafs doors fixtures are:- 1) SS 304 ball bearing butt Hinges of size 125x63x3mm - 6 Nos. 2) D type Handle 300 x 25mm in SS 304 - 2 nos 3) SS 304 Tower bolt 12mm dia 300x38x2.4mm – 2nos 4) Mortise dead lock with Europro file Cylinder 60mm Length (one side key other side thumb turn) with 4 level Master Key - 1 no for

Supplying, fabricating and fixing in position UPVC windows using JP 23 (80mm X 50mm 1.3 Kg/m) and JP 111 (80mm X 50mm 1.5kg/m) UPVC profiles for the outer frame. Total breadth is being divided equally into two or more shutters by using UPVC profile JP 050 (60mm X 36mm 0.80 Kg/m) and complete with fusion welding, 12.mm thick GI reinforcement and complete the window by fitting with 4mm clear glass with UPVC glass bead JP 022.(35mm X 18mm 0.27 Kg/m) including cost of all materials, labours, power consumption required for fabrication, drilling holes in RCC column, slab, masonry walls wherever necessary with power drills to the required extent and make good to the original condition after fixing and also as directed etc., complete.

Plain Cement Concrete 1:2:4 (One Cement, two M.sand and four hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and paving the floor with design mat finished ceramic tiles of approved brand and quality of size 300 X 300 X 8mm in all floors over a base mortar using cement mortar 1:3 (One cement and three M.sand) 20mm thick laid in situ true to alignment and pointed with colour cement (White cement mixed with colouring pigment) to suit the colour and shade of the ceramic tiles used neatly and fixed in position without any air gap in between the ceramic tiles etc., complete complying with standard specification and as directed by the departmental officers. (The sample colour and shade of the ceramic tiles should be got approved from the departmental officers before use on works).

Dadooing the walls with best quality glazed tiles of approved design, colour of size 30 cm X 45 cm over the base plastering of cement mortar 1:3 (One cement and three M.sand) 12mm thick and set in cement mortar 1:2 (One cement and two M.sand) and pointed with colour cement and finishing neatly as directed by the departmental officers., etc, complete complying with standard specification.

Paving the floor with Designed Colour double charged Vitrified tiles of size 60 x 60 x 8mm in all floors over a base layer of Cement Mortar 1:3 (One cement and three M.sand) 20mm thick and pointed with white cement mixed with colouring pigments at the rate of 0.3 Kg/sq.m including finishing neatly and curing, etc. complete, complying with standard specification and as directed by the departmental officers. (The basic cost of the tiles should not be less than Rs.90/Sq.ft )

Supplying and fixing MS grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification. The type design for the grills will be given by the Engineers,i/c.,

Supplying and erecting of 2000 litre capacity PVC Sintex water tank to ISI standard of approved quality and make including labour charges for fixing and fixtures etc. complete.

Supplying and fixing in position best approved ISI quality PVC Rain water down fall pipes of 110mm dia meter having working pressure of 4Kg/Cm2 including cost of PVC pipe, with necessary shoes, bends, nails, teakwood plugs, screws etc., and fixing of cost iron gratings of required dia meter and special clamps at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The PVC pipe shall be fixed with teak wood plugs by means of “U” clamps using brass screws. Special types of “U” clamp at the centre of the pipeline shall be fixed in addition to those for more than 3 meter pipe length complying with standard specifications.

Supply laying and jointing PVC pipe of approved quality and make of the following dia fixed on walls with necessary clamps and screws including cutting and threading wherever necessary, etc. complete complying with standard specification and as directed by Engineer-in-charge. (Above Ground Level) 110mm dia PVC pipe with ISI mark - 6 Kg/Cm2

63mm dia PVC pipe with ISI mark - 6 Kg/Cm2

32mm dia PVC pipe with ISI mark - 10 Kg/Cm2

25mm dia PVC pipe with ISI mark - 15 Kg/Cm2

Providing inspection chambers of size 60 x 60 x 90 cm (inner dimension) using 9” thick brick walls using second sort table moulded chamber burnt bricks of sizes 9”x 4½”x3” in Cement Mortar 1:5 (One cement and five M.sand) and plasting inside with cement mortar 1:3 (One cement and three M.sand) 12mm thick and outside surfaces in C.M. 1:5 (One cement and five P.sand) 12mm thick. A precast cover slab of 75mm thick with RCC 1:11/2:3 (One cement one and half M.sand and three hard broken stone jelly) shall be provided for the chamber. The rate includes necessary earth work excavation to the required depth, Plain Cement Concrete 1:5:10 (One cement five M.sand and ten aggregate) 75mm thick etc., complete with standard specification and as directed by the Engineer,i/c.,

Supplying and fixing in position the following Gun metal gate / wheel valve of best quality and approved make and heavy type quality including cost of cutting, threading of the pipes and fixing of the G.I. pipe in position with white lead, spun yarn etc., complete complying with standard specifications. 40mm dia GI Gate valve (with ISI mark)

25mm dia GM Gate valve (with ISI mark)

White washing two coats using freshly burnt shell lime white in colour. Fevicol type gum should be used in the preparation of white wash solution, adequate quality of approved blue powder to be added to white wash solution for application to the walls etc., complete complying with standard specification.

Painting two coats of exterior emulsion paint over one coat of exterior primer using best qualityand approved colour of paint, brushes, scaffolding charges etc. complete complying with standard specification. Paint, primer and colour have to be got approved by the Engineer,i/c.,

Painting two coats of new iron works such as steel doors, windows, ventilators, windows bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Engineer,i/c., before use on works).

Providing rain water harvesting pit by earth work excavation in circular shape of 90 cm dia at 100 cm depth. The pit is encased with well ring of 90 cm dia , 30 cm depth, 50 mm thick using RCC 1:2:4 using 20 mm metal for 4 nos. The entire depth ie. 120 cm is filled with 40 mm size metal. The top of the pit is covered with RCC 1:2:4 50mm thick perforated slab including cost and fabrication of reinforcement grills for ring and cover slab, labour charges, cost of materials, moulding curing, finishing and fixing in position etc. complete.

Supplying and fixing in position by means of 75 mm long and 65 mm dia counter sunk bolt and nuts embedded in the floor with rubber or fiber washer white glazed European Water Closet white colour with 100 mm "P" trap with double flapped rigid PVC black seat and seat cover with C.P. brass hinges including supply and fixing 10.00 liters capacity PVC low level flushing tank, etc., complete with all fittings such as 15 mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40 mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15 mm brass connections, 15 mm C.P. Angle clock valve, 15 mm brass nipple (2 Nos.), 15 mm nylon connection and fixing the low level ISI marked flushing tank with T.W. plugs and screws and giving necessary connection to the PVC pipe including cost of 600 mm length of 100 mm dia PVC Pipe and painting the Brackets with 2 coats of approved paint over one coat of red oxide primer and redoing the dismantled masonry to original condition etc. complete. (The EWC and flushing tank should be got approved by the departmental Engineers before use on works)

Supply and fixing of health faucet of good quality and approved make etc., complete and as directed by the Engineer,i/c., (The health faucet should be got approved by the Engineer,i/c., before use on works).

Supplying and fixing of 15mm CP two way tap of good quality and approved make in correct position etc., complete with standard specifications and as directed by the Engineer,i/c.,

Supplying and fixing in position best quality and approved make Indian made white glazed earthenware wash hand basin of size 550 X 400mm white colour of approved brand and quality including cost of cast iron brackets / fisher bolts 15 mm dia brass CP pillar tap, 32 mm dia bottle trap 32mm dia C.P. brass waste coupling with rubber plug and chain 15 mm brass nipple 15 mm dia nylon connection, 15mm CP angle clock including fixing of wash basin in the wall in position with a pair of fisher bolts / CI brackets with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc. complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Departmental Engineers before use on works).

Supply and fixing in position of best Indian make white glazed earthernware lipped mouth flat back urinal of best approved quality of size 430mm x 260mm x 350mm with GI pipe connection, PVC waste pipe fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masonry if necessary and re-doing the same to the original condition as directed complying with standard specifications

Supplying and fixing in position 15 mm dia C.P. long body tap (Heavy type) of approved make conforming to IS specification and quality including cost of shellac, thread, etc., complete, complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Departmental Officer before use on the works)

Supply and finishing in position of Solid PVC door shutters using 19 gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for paneling shall rigidly fixed in position including necessary furniture fittings. The overall size of styles shall be 50mm X 30mm. The overall size of top rail, lock rail and bottom rail shall be 75mm X 30mm. The overall size of frames shall be 50mm X 45mm with suitable rebate for housing the shutter. (Solid panel PVC door with Frame)

Supplying and fixing of partition with new one of aluminium anodized natural colour matt finish 1/3 glazed, 2/3 prelaminated particle board partition with alu. Box section No.20062, 20063 of size 63.50mm x 38.10mm x 1.28mm, 1.41mm @ 0.818kg/m, horizontal members are spacedat 90cm c/c and to vertical members are spaced at 1.20m, 2.10m and 2.80m height from floor level, panels should be covered with 12mm thick prelaminated exterior grade at 2/3 portion of partition and 5mm thick, plain glass covered at 1/3 portion of the partition with necessary aluminim clips of size 19mm x 17.30mm x 0.90mm at 0.124 kg/m, and L angles etc, the aluminium surface is to be anodized withmatt finish under electrically controlled condition inaccordance with ISI 1868/1962 specification for an average anodic film thickness and cost of materials conveyance scaffolding if any required etc and necesarydismantling making holes in RCC brick masonry wherever necessry with power drill to the extent required and made good to the original condition after fixing the partition as direced by the departmental officers. All materials should be got approved by the Engineer,i/c. before fixing in position, etc. complete.

Supplying and fixing of Door with aluminium anodised natural colour matt finsh half glazed half PLB door with outer frame using alu. Box section and of size 101.60mmx44.75mmx1.75mm at 1.367 Kg/m shutter frame at bottom using alu. Box section of size 95.25mm x 44.45mmx1.74mm at 0.881kg/m, at vertical (lock rail) using 47.62mmx44.45mmx1.52mm @0.881 kg/m and vertical plain using 47.62mmx44.45mmx1.74mm at 0.881kg/m bottom and top panel covered with 12mm thick prelaminated board and 5mm thick plain glass with necessary accessories such as rubber beading, aluminium clips of size 19mm x 17.30 x 0.90mm at 0.124 kg/m, and 'L' angles door stopper handle, mortice lock 150mm tower bolt, 125mm hinges, screws, PVC woolen felt, etc. complete the rate inclusive of labour power consumption charges required for fabrication if necessary clipping, dismantling the masonry RCC beams columns wherever necessary with power drill to the extent required and made good tothe original conditionafter fixing, etc. the complete the alu. surface to be anodized with matt finish under electrically controlled condition inaccordance with ISI specification 1868/1962 of anodic film thickness for all section all the materials should be got approved by the Engineer,i/c. before fixing inposition, etc. complete.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI / 1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the departmental Engineer,i/c., before use on work.

Plastering of walls in cement mortar 1:3 (One cement and three P.sand) 20mm thick in all floors with water proofing compound at 2% by weight of cement and finishing neatly including provision of cement mortar bands and raised plastering for doorways wherever required and as directed without any extra claim complying with standard specifications.

Supplying and fixing in position Indian make decorative type wooden framed Mirror of approved quality and brand of size 600 x 450 mm x 5.5 mm shelf type with necessary ply wood backing, rubber buttons, brass CP screws, T.W. plugs etc. complete complying with standard specification. (The mirror should be got approved by the Departmental Officer before use on woks)

Supplying and fixing in position best approved quality C.P. brass soap tray of size 150 x 150 mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position best quality brass chromium plated towel rail of 600mm length 20mm dia with CP brackets of same materials including fixing with necessary T.W. plugs, brass C.P. screws and dismantling masonry etc., complete with standard specifications. (The towel rail should be got approved by the Departmental officer before use on works).

Flooring with the Eurocon tiles of size 300mm x 300mm laid over cement mortar 1:3 (One cement and three M.sand) 20mm thick and pointing the joints to full depth of slabs with cement mortar 1:3 (One cement and three P.sand) mixed with colour oxide including laying, finishing, polishing with machine polish, curing etc., complete complying with standard specification.

Supply and fixing of granite sink size 2’-0” X 2’-0” X 1’-0” of good quality and with a pair of M.S. angle, brackets, 40mm PVC waste pipe with necessary coupling T.W. plugs, screws, washers, white lead, etc., including painting two coats including dismantling the masonry if necessary and recovering the same to the original condition as directed. (The granite sink to be used on work should be got approved by the Engineer,i/c., before use on work).