Sports Development Authority Of Tamil Nadu Tender

Brick work in following Cement Mortar using Fly Ash Bricks of 230 x 110 x 75mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

Plastering with Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

Renewing and laying and jointing UPVC Pipe(Un-Plasticized Polyvinyl Chloride) UPVC used for residential and home applications, water pressure in residential areas do not normally exceed the maximum tolerance.(schedule-40) but excluding cost of such specials and fixing in position dismantling masonry and make the same to original condition etc complete complying with standard specification and as directed by the departmental officers at site of work.

100mm dia of pipe

80mm dia of pipe

Supplying and fixing in position first quality and approved variety of Upvc ball valve of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

100mm dia of pipe

80mm dia of pipe

Dismantling , removing and carefully stacking Doors &windowsincludung removal of frames,hinges and fastenings etc., complete complying with standard specification and as directed by the departmental officers at site of work.

Supplying and fixing in position white glazed European Water Closet of best quality and make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings.such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supply and fixing in position of best Indian make white glazed earthernware Lipped mouth flat back urinal of best quality and approved make of size 380X400X590 mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Renewing the damaged broken unservicewable Health faucit with new one of Two way bib cock tap with flexible hose 15mm dia of approved quality and make including labour charges for fixing in position etc complete complying with standard specification and as directed by the departmental officers at site of work.

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position Wooden Polymer Composite (WPC) door with frame including furniture fittings hinges, Handle, Aldrop, Tower bolt etc., complete and asd irected by the departmental officers.

Supplying and fixing in position 15mm dia Long body tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing flush door with teak wood frame made by 32mm thick flush door with both side approval laminate sheet and all edges with teak wood lipping alrouynd and necessary locking arrangements such as 4Nos of hinges, lock with approved handles, aldrops etc., The outer frame to be fixed properly from true ceiling. The rate inclusive of cost of teak wood frame, Hydraulic door closer (make -OZONE SS NSK) and with all furniture fiitings and labour charges ans as directed by the deparrtmental officers.

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Renewing and laying and jointing UPVC Pipe(Un-Plasticized Polyvinyl Chloride) UPVC used for residential and home applications, water pressure in residential areas do not normally exceed the maximum tolerance.(schedule-40) but excluding cost of such specials and fixing in position dismantling masonry and make the same to original condition etc complete complying with standard specification and as directed by the departmental officers at site of work.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

110mm dia Elbow door

110mm dia Tee door

Cleaning the marbles, Granite and tiles area using necessary chemicals including labour charges, cost of brushes, jire charges for cleaning mavhine etc., complete and as directed by then departmental officers.

Renewing and refixing the damaged ventilator with newone of aluminium anodized natural colour matt finish louvered ventilator. The louvers with moving arrangements will be made with aluminium channel of size 60 x 30 x 4mm @ 0.27 Kg/M with necessary glass panes for louver 4mm thick aluminium clips, 'L' angles screws, nails, conveyance scaffolding if any and power consumption charges required for fabrication wherever necessary with power drill to the extent required and made good to original condition after fixing etc complete complying with standard specification and as directed by the departmental officers at site of work.The aluminium surface is matt finish under electrically controlled condition in accordance with ISI 1868 / 1962 anodic film thickness of not less than 15 microns for all sections.

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Renewing and fixing Angle Cock with new one of approved quality Metro or Equal Brand and approved make including labour for fixing in position etc complete complying with standard specification and as directed by the departmental officers at site of work.

Supplying and fixing in position 15mm dia brass CP Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Repainting the old wood work two coats in all floors with best Synthetic enamel paint of approved quality, colour and brand including thorugh scrapping, sand papering and preparation of surface including cost of bruses, high scaffolding charges neat finishing etc complete complying with standard specification and as directed by the departmental officers at site of work.

Labour charges for removing and relaying the old available paver blocks over the compacted bed of course sand or quarry dust etc and compacting and proper embedding / laying of old available inter locked paver blocks in ture and straight alignment with proper gradient over the sand bedding layer through vibratory compction by using the plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and compacting the paver surface neatly with out any undulations and sweeping the extra sand and cleaning the paver surface neatly etc., complete complying with standard specification and as directed and full satisfaction of departmental officers

Renewing the damaged paver block with new one of paving and laying the rubber moulded hydraulic presses paver block inter locked blocks with new one of 83mm thick inter locked blocks of approved quality and make over a sand cushion and laying the paver blocks in true and straight alignment with gradient and pointing neatly using quarry dust of fly ash and pointing neatly hire charges for vibrator machine including diesel consumption charges etc., complete complying with standard specifications and as directed by the departmental officers.

Renewing the damaged false ceiling with new 2 square PVC Laminated GYPTEX False ceiling in the true horizontal level false ceiling grid using hot dipped galvanized steel section exposed surface chemically cleaned capping pre finished in baned poly system paint wall angle of size 3000x24mmx24mm using in periphery of the ceiling fixed to the wall partition RC columns band walls with the held of screws of 60mm main runner of size 24x35x3000mm suspended at a 1200mm c/c by using 24x14mm angles hanger securely fixed to the structural soffits of RC slab by using 6mm cross tee of size 24x26x1200mm to be inter locked between in main runner at 600mm c/c mark to form a grid of 600x600mm long cross tee of size 24x26x600mm fixed in between 1200mm long cross tee for forming a grid of 600mmx600mm finally laying high quality viny film with back side aluminium foil PVC laminated gypsum ceiling tiles regular of size 595x595x7.50mm to 8mm thick of noise reduction co-efficient NRC of 01-03 relative humidity 95% density of 780kg.m3 and light refection 0.75 etc., complete.

Painting two coats of old plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour without primer including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of Exterior wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Repainting the old wood work two coats in all floors with best Synthetic enamel paint of approved quality, colour and brand including thorugh scrapping, sand papering and preparation of surface including cost of bruses, high scaffolding charges neat finishing etc complete complying with standard specification and as directed by the departmental officers at site of work.

Repainting the old iron work two coats of synthetic enamel paint of approved quality and colour and brand including thorough scrapping preparation of surface and finishing neatly etc complete complying with standard specification and as directed by the departmental officers at site of work.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position MS Sqaure tube column 0f 3m height for a size 300x300x10mm thick and base plate of size 450x450x12mm thick attached with bottom of the column and J -hooks fixed over the Concrete base including Earth work of size 0.92x0.92x0.92mm, stone dust filling. PCC1:5:10, and Reinforced cement concrete Column of size 0.60x0.60x0.60mm using RCC 1:1 1/2:3 concrete placing in the foundations and inserted of J hooks with Base plate on the concrete surface including steel fabrication etc., complete and as directed by the departmental officers.

Supplying anf fixing in position MS Gate of size 4.00m x2.50m using MS Rectangular tube section of size 80 x 40mm and 60x40mm with necessary furniture fittingd such as MS Aldrop 200mm length 2Nos - Ornamental handle, 6Nos of Holdfasts etc.,finally finishing with Two coat of synthetic enamel paint over one coat of Red oxide primer etc., complete and as directed by the departmental officers.The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supply and fixing Weld mesh7.50cmx2.50cm 10 gauge including labour charges for fixing and cutting welding charges etc., complete complying with std. specification and as directed by the deptl. Officer.

Removing the Existing damaged weld mesh (5cm x5cm) with MS angle Section partition Servicing, cutting and welding with required size including labour charges for removing and Refixing the same in position including cost of fastening screws, hinges and fixing charges etc., complete complying with std. specification and as directed by the department officers

Servicing the unfunctioning Colapsible gate repairing the Rolling Wheel necessary welding and Grees applying etc.,Complete.The rates including labour charges for SEP and the same in position including cost of fastening screws, hinges and fixing charges etc., complete complying with std. specification and as directed by the department officers

Clearing the sewer line and gully trap with split bamboos and coir ropes and removing the silt and slush etc., complete.

Repair and Retrofitting Works:Providing of Corrosion Repair treatment for the RCC Structure with the following specification : Prepare the surface by chipping the spalled and old concrete of the column, beam and slab. Check for the phenolphthalein test and if there is no change in colour chip the same further down until, reaching the good or uncontaminated concrete. Clean the surface and make sure that surface is clean and free from loose particle at an average thickness of 30 to 50mm. In case of greater thickness the same shall be accounted on additional measurement.

Prior to installation of the Galvashield XPI units, check the continuity of the steel reinforcement. Any loss of continuity will require additional electrical connections or restoration of continuity by effective means. Select a location for the Galvashield XPI as close as practical to the edge of the repair zone. Galvashield XPI units should be positioned around/along the repair boundary. In addition to standard substrate preparation, the Galvashield XPI anode(s) shall be thoroughly pre-soaked in clean water for a minimum of 10 minutes and a maximum of 20 minutes, prior to the application of the repair mortar. Tighten tie wires using Galvashield Fixing Tool so that no free movement is possible, thus ensuring good electrical continuity. To test electrical continuity between tie wires and reinforcement bar a continuity meter should be used. The anodes shall be spaced at 1 Nos/ Sq.m for slab and 1 Nos. / Rmt for beams

Providing of Protective Coating with the following specification : Prepare and clean the surface and remove any dust, unsound or contaminated material, plaster, oil, paint, grease, corrosion deposits or algae using necessary tools/ eqipments based on the site condition. Clean the surface and make sure that there are no foreign materials. Water wash the surface and allow it to dry. Apply one coat of primer a as per the standard specification and apply the top coat, two coats of Dekguard S, one after the other dries. - Complete.The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete

Erection of scaffolding in areas where the repair is to be done using a 2 legged steel pipe cuplock system wherever required Etc Complete.

Providing treatment to the existing damaged pre-cast expansion joints with the following specifications. All the precast joints shall be cleaned free of existing debris and dirt and shall be prepared neatly. The sides shall be roughened using a necessary tool followed by dry blowing the surface to prevent the presence of fine dust. The joints shall be treated by preparing the polymer modified shrinkage compensated reinstatement mortar Rendroc S2, a two component cement based blend of powder and liquid polymer using a heavy duty mixer. The same shall be applied in all the joints matching the existing level and finish the same neatly. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading charges,dismantling if any needed and redoing the same to good surfaces and all other incidental charges etc., complete

Providing of Expansion Joint Treatment with the Following Specification: Along all the areas of expansion joint. All dirt, laitance, loose material and foreign matter. Clean the surface and remove any dust, unsound or contaminated material, plaster, oil, paint, grease, corrosion deposits or algae shall be removed using necessary toool. The are shall be cleaned free of dust and dirt and ensure that the surface is completely dry. Mark lines on either sides of the expansion joint where the high performance elastomeric joint sealant tape Exponband One manufactured by M/s. Fosroc of 200mm wide and 2mm thick is to be installed. Mix the two component adhesiveNitobond PC40 manufactured by M/s Fosroc and apply the same on to the surface of the concrete/wall where the adhesive shall be pressed on to the expansion joint tape for the balance width of the tape on both the edges. The same shall be ensured by gently rolling on the edges to ensure that there is no entrapped air. Upon completion of the application of the elastomeric joint tape, the two component epoxy adhesive may be applied over the top of the tape all along the edges ensuring the gap (if any) between the tape and the concrete/wall surface is sealed thoroughly. In case of over lap along the length, the same shall be given a lap of 50mm and pasted using epoxy adhesive or fused using hot air blower. Upon completion of the application of the tape, the same is allowed to dry for a period of 48 hours. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete

Electrical and Fire Fighting :Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffoldingand re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers.Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and kept in position of Trolley Mounted Type 22.5 kg. Carbon-di-Oxide Fire Extinguisher as per IS15683, complete with control valve, gun metal cap, pressure gauge' operation sticker, discharge hose, mounting trolley with moving wheel, safety clip, etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT