National Institute Of Ocean Technology Tender

Providing and fixing UPVC Air Tight Sliding Windows frame/Glazed Panel window with UPVC Shutter frame as per site condition with necessary door running frame work in top , sides, bottom , the rate including all hardware fittings like glass and lock , necessary hardware fitting arrangements all etc. fixed to the shutters, as approved. all complete as per instruction of Engineer In-charge.(Model available at NIOT campus) Note: Fully Air tight Sliding UPVC Door in the operation time no vibrations, shacking should not be obtained so providing and fixing of necessary strong all around support section must be provided as per the site condition. Rate including of frosted film for glass. Note: Measurement taken as per site condition only actual work done site Length X Height, wastage is not considered. Make: Gealan, Qute, Fenesta. Approx Size 2 nos x 1.52 (w) x 1.1 (H)

Providing and fixing 6mm thick Lacquered glass using of while board . The glass back side using 12mm thick Commercial ply paneling with Sealant and necessary frame supports and all around finish with aluminim beading all necessary fitting arrangements etc all complete as per instruction of EIC.Make of Ply - Century, Green Ply, Archid Ply, Kit Ply ; Make of Glass : Saint Gobain

Taking out doors, windows and clerestory window shutters of Aluminium including removal of grill and stacking within 50 metres lead :lead starts from ground floor only (inclusive carriage of unserviceable material from 3rd floor to ground floor) Of area 3 sq. metres and below

Wall painting with Premium acrylic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on old work Make : Asian ,Nerolac, Berger

Providing and fixing of UPVC door with neccessary frame/ shutters , the door shall be 3D hinged for better weight capacity. Door has to be provided with variety of security device like muti point locksystem with cylinder lock facilitated handle inclusive of neccessary hardware fittings etc as directed by EIC.The door shall have 5mm thick single glass at top half and 20mm thick multichambered hollow uPVC panel at bottom. Approx size 1.0m(W) x 2.1 m (H)

TOTAL WITHOUT GST

Erecting/Dismantling double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding,scaffolding top to providing plywood platform,steel platform and necessary steps arrangements,necessary safety arrangements for platfrom top. Note :The Contractor must arrange for all necessary safety equipment including safety shoes, helmets, harnesses, jackets, safety rope with proper arrangement, all complete as per instruction of Engineer in Charge.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Removing the existing damaged Grid False ceiling Providing and fixing New Grid false ceiling in true horizontal level false ceiling as per the drawing, of approved make, using hot dipped galvanized steel section exposed surface chemically cleaned capping prefinished in baked polyester paint wall angle of size 3000mm x 19mm x 19mm used in the perphery of the ceiling fixed to the wall partition/ RC column band walls with the help of screws at 600mm C/C. Main runner of size 3000 x 15 x 32mm suspended at 1200mm C/C. by using 2mm / 3mm dia GI wire hange securely fixed to the structural soffit of RC slab/Structural steel by using 6mm anchor fastner at every 1200mm (max) a 1200mm long cross tee of size 15 x 32mm to be interlocked between in main runner at 600mm C/C (max to form a grid of 600 x 600mm. 600mm long cross tee of size 15 x 32mm fixed in between 1200mm long cross tee for forming a grid of 600 x 600mm. Finally laying 16 mm thk 600 x 600mm Wetformed mineral fiber tile with Factory applied latex paint. Fire rating of 60 minutes as per BS 476/23 of 1987, Noise Reduction Co-efficient (NRC) of 0.55, light Reflectance of 84%, sound attenuation of 34db, Thermal conductivity K-0.052 - 0.057 W/MOK, weight of 3.53Kg/Sqm and Humidity Resistance of RH - 99%. Note: The false ceiling area will be measured in flat area only . Location: Main building / 3rd floor /Room no. 414 Make :Armstrong,Saint gobain

Dismantling aluminium/ plywood partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead(inclusive carriage of unserviceable material from 3rd floor to ground floor) as directed by Engineer-in-charge. Leads start from Ground floor

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 12 mm cement plaster

Providing and fixing Commercial grade Wall Paper of approved shade with recommended Adhesive of approved make which have 100% washable, Scratch resistance, Peel proof, & fire retardant properties. Cost to include preparation of surface with Oil Primer etc.all complete as per instruction of Engineer in charge.

OUTER WALLS RAINCOAT CLASSIC WATERPROOFING:Surface shall be cleaned throughly with wire brush/Scrubbing/jet washing for removal of all unwanted things like dust, dirt and foreign materials etc .Fill the large cracks in the surface with polymer modified mortar using Dr. Fixit Pidicrete URP.Providing & Applying First of Basecoat as Raincoat WPC as Applying second coat of Raincoat WPC and Third coat of Dr. Fixit Raincoat Classic – singlecomponent UV stable Top coat in approved shade for exterior coating comprised of high quality acrylic emulsion polymer,light fast & weather durable pigments, properly selected & graded fine fillers, additives & biocides. The material shall beapplied un-diluted in right angle to Universal Basecoat layer and DFT of 190 microns, as per manufacturers recommendation, etc, complete. The product shall haveElongation 100% as per ASTM D 412, Tensile strength : 2.5Mpa as per ASTM D 412, Water Resistance conforming to SS500, Crack bridging ability conforming to Class A4 as per EN1062 Part 7, Positive hydrostatic pressure 7 bar as per DIN1048, Anti-carbonation property complying EN 1062 Part 6,RCPT conforming to ASTM C 1202 all complete etc.,as per instruction of Engineer in charge

Providing and laying RCC Pedestal (1:2:4) of Size 20" (L) X 10" (W) *10" (H) Rate inclusive of necessary reinforcement & Shuttering etc all complete as per direction of Engineer in charge.

Providing and fixing of Cupboard using 18 mm thick BWR ply wood the cupboard wide is 500mm and finished with 3 to 4mm thick veneer sheet finish polish with necessary beading and lipping and front faces are the shutter using 4 to 5mm clear glass with magnetic lock and the storage unti should including ISI marked SS hinges of required with necessary hardware fittings, handle etc,. complete as per instruction of EIC (colour and shadow approved by EIC ) Storage Unit : 1.00m(L)x0.50m(B)x 0.75m(ht.) -2nos.Note:model available in NIOT campus before quoting the rate contractor should visit the site. Measurement taken as per site condition only actual work done site Lenght X Height ,wastage not considered Make : Plywood - Green Ply,Kitply Plywood,Sharen.

Providing and Fixing Aluminium partition with hollow section of size 50*50mm at every 600mmc/c in both ways (Horizontal & vertical) .12mm Thick Gypsum board to be fixed with necessary screws on both sides ,horizontal and verticals joints of panel to be staggered and all joints to be taped and finished with joints paper tape and jointing compound.The Gypsum board joints to be finished in all respects using tape,the rate should inclusive of two coat putty, one coat of primer and 2 coat plastic emulsion paint.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of Interior wall primer of approved brand and manufacture on wall surface:Water thinnable cement primer.

GST 18%

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)